/****************************************************************************
 * boards/risc-v/esp32c3-legacy/common/src/esp32c3_board_apds9960.c
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

#include <errno.h>
#include <debug.h>
#include <stdio.h>

#include <nuttx/spi/spi.h>
#include <nuttx/sensors/apds9960.h>
#include <arch/board/board.h>

#include "esp32c3.h"
#include "esp32c3_i2c.h"
#include "esp32c3_gpio.h"

#include "esp32c3_board_apds9960.h"

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Use IO1 as APDS9960 INT */

#define GPIO_APDS9960_INT    1

/****************************************************************************
 * Public Functions
 ****************************************************************************/

struct esp32c3_apds9960config_s
{
  /* Configuration structure as seen by the APDS-9960 driver */

  struct apds9960_config_s config;

  /* Additional private definitions only known to this driver */

  void *arg;  /* Argument to pass to the interrupt handler */
  xcpt_t isr; /* ISR Handler */
};

/****************************************************************************
 * Private Function Prototypes
 ****************************************************************************/

static int  apds9960_irq_attach(struct apds9960_config_s *state,
                                xcpt_t isr, void *arg);

/****************************************************************************
 * Private Data
 ****************************************************************************/

/* A reference to a structure of this type must be passed to the APDS-9960
 * driver.  This structure provides information about the configuration
 * of the APDS-9960 and provides some board-specific hooks.
 *
 * Memory for this structure is provided by the caller.  It is not copied
 * by the driver and is presumed to persist while the driver is active. The
 * memory must be writable because, under certain circumstances, the driver
 * may modify frequency or X plate resistance values.
 */

static struct esp32c3_apds9960config_s g_apds9960config =
{
  .config =
    {
      .irq_attach  = apds9960_irq_attach,
    },
};

/****************************************************************************
 * Private Functions
 ****************************************************************************/

/* Attach the APDS-9960 interrupt handler to the GPIO interrupt */

static int apds9960_irq_attach(struct apds9960_config_s *state,
                               xcpt_t isr, void *arg)
{
  irqstate_t flags;
  int ret;
  int irq = ESP32C3_PIN2IRQ(GPIO_APDS9960_INT);

  sninfo("apds9960_irq_attach\n");

  flags = enter_critical_section();

  /* Configure the pins that will be used as interrupt input */

  esp32c3_configgpio(GPIO_APDS9960_INT, INPUT_FUNCTION_1 | PULLUP);

  /* Make sure the interrupt is disabled */

  esp32c3_gpioirqdisable(irq);

  ret = irq_attach(irq, isr, arg);
  if (ret < 0)
    {
      leave_critical_section(flags);
      syslog(LOG_ERR, "ERROR: apds9960_irq_attach() failed: %d\n", ret);
      return ret;
    }

  /* Setup interrupt for Falling Edge */

  esp32c3_gpioirqenable(irq, FALLING);

  leave_critical_section(flags);

  return OK;
}

/****************************************************************************
 * Public Functions
 ****************************************************************************/

/****************************************************************************
 * Name: board_apds9960_initialize
 *
 * Description:
 *   Initialize and register the APDS9960 gesture sensor.
 *
 * Input Parameters:
 *   devno - The device number, used to build the device path as /dev/gestN
 *   busno - The I2C bus number
 *
 * Returned Value:
 *   Zero (OK) on success; a negated errno value on failure.
 *
 ****************************************************************************/

int board_apds9960_initialize(int devno, int busno)
{
  struct i2c_master_s *i2c;
  char devpath[12];
  int ret;

  sninfo("Initializing APDS9960!\n");

  /* Initialize I2C */

  i2c = esp32c3_i2cbus_initialize(busno);
  if (i2c == NULL)
    {
      return -ENODEV;
    }

  /* Save this i2c in the config */

  g_apds9960config.config.i2c_dev  = i2c;
  g_apds9960config.config.i2c_addr = APDS9960_I2C_ADDR;

  /* Then register the gesture sensor */

  snprintf(devpath, sizeof(devpath), "/dev/gest%d", devno);
  ret = apds9960_register(devpath, &g_apds9960config.config);
  if (ret < 0)
    {
      snerr("ERROR: Failed registering APDS-9960!\n");
    }

  return ret;
}