/**************************************************************************** * boards/arm/lpc31xx/olimex-lpc-h3131/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H #define __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Clocking *****************************************************************/ /* Frequency of the FFAST input */ #define BOARD_FREQIN_FFAST (12000000) /* ffast (12 MHz crystal) */ /* HPLL0 configuration */ #define BOARD_HPLL0_FINSEL CGU_HPFINSEL_FFAST /* Frequency input selection */ #define BOARD_HPLL0_NDEC 131 /* PLL N-divider value */ #define BOARD_HPLL0_MDEC 29784 /* PLL M-divider value */ #define BOARD_HPLL0_PDEC 7 /* PLL P-divider value */ #define BOARD_HPLL0_SELR 0 /* SELR bandwidth selection */ #define BOARD_HPLL0_SELI 8 /* SELI bandwidth selection */ #define BOARD_HPLL0_SELP 31 /* SELP bandwidth selection */ #define BOARD_HPLL0_MODE 0 /* PLL mode */ #define BOARD_HPLL0_FREQ 406425600 /* Frequency of the PLL in MHz */ /* HPLL1 configuration */ #define BOARD_HPLL1_FINSEL CGU_HPFINSEL_FFAST /* Frequency input selection */ #define BOARD_HPLL1_NDEC 770 /* PLL N-divider value */ #define BOARD_HPLL1_MDEC 8191 /* PLL M-divider value */ #define BOARD_HPLL1_PDEC 98 /* PLL P-divider value */ #define BOARD_HPLL1_SELR 0 /* SELR bandwidth selection */ #define BOARD_HPLL1_SELI 16 /* SELI bandwidth selection */ #define BOARD_HPLL1_SELP 8 /* SELP bandwidth selection */ #define BOARD_HPLL1_MODE 0 /* PLL mode */ #define BOARD_HPLL1_FREQ 180000000 /* Frequency of the PLL in MHz */ /* The following 3 bitsets determine which clocks will be enabled at * initialization time. */ #define BOARD_CLKS_0_31 \ (_RBIT(CLKID_APB0CLK,0)|_RBIT(CLKID_APB1CLK,0)|_RBIT(CLKID_APB2CLK,0)|\ _RBIT(CLKID_APB3CLK,0)|_RBIT(CLKID_APB4CLK,0)|_RBIT(CLKID_AHB2INTCCLK,0)|\ _RBIT(CLKID_AHB0CLK,0)|_RBIT(CLKID_ARM926CORECLK,0)|_RBIT(CLKID_ARM926BUSIFCLK,0)|\ _RBIT(CLKID_ARM926RETIMECLK,0)|_RBIT(CLKID_ISRAM0CLK,0)|_RBIT(CLKID_ISRAM1CLK,0)|\ _RBIT(CLKID_ISROMCLK,0)|_RBIT(CLKID_INTCCLK,0)|_RBIT(CLKID_AHB2APB0PCLK,0)|\ _RBIT(CLKID_EVENTROUTERPCLK,0)|_RBIT(CLKID_CLOCKOUT,0)) #define BOARD_CLKS_32_63 \ (_RBIT(CLKID_IOCONFPCLK,32)|_RBIT(CLKID_CGUPCLK,32)|_RBIT(CLKID_SYSCREGPCLK,32)|\ _RBIT(CLKID_OTPPCLK,32)|_RBIT(CLKID_AHB2APB1PCLK,32)|_RBIT(CLKID_AHB2APB2PCLK,32)|\ _RBIT(CLKID_AHB2APB3PCLK,32)|_RBIT(CLKID_EDGEDETPCLK,32)) #define BOARD_CLKS_64_92 \ (0) /* LED definitions **********************************************************/ /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in * any way. The following definitions are used to access individual LEDs. */ /* LED index values for use with board_userled() */ #define BOARD_LED1 0 #define BOARD_LED2 1 #define BOARD_NLEDS 2 /* LED bits for use with board_userled_all() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) #define BOARD_LED2_BIT (1 << BOARD_LED2) /* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is * defined. In that case, the usage by the board port is as follows: * * SYMBOL Meaning LED state * LED2 LED1 * ------------------------ -------------------------- ------ ------ */ #define LED_STARTED 0 /* NuttX has been started OFF OFF */ #define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF */ #define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF */ #define LED_STACKCREATED 1 /* Idle stack created ON OFF */ #define LED_INIRQ 2 /* In an interrupt N/C N/C */ #define LED_SIGNAL 2 /* In a signal handler N/C N/C */ #define LED_ASSERTION 2 /* An assertion failed N/C N/C */ #define LED_PANIC 3 /* The system has crashed N/C Blinking */ #undef LED_IDLE /* MCU is is sleep mode Not used */ /* Thus if LED2 is statically on, NuttX has successfully booted and is, * apparently, running normmally. If LED1 is flashing at approximately * 2Hz, then a fatal error has been detected and the system has halted. * * NOTE: That LED2 is not used after completion of booting and may * be used by other board-specific logic. */ /* Button definitions *******************************************************/ /* The Olimex LPC_H3131 has no user buttons */ /**************************************************************************** * Public Data ****************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Public Function Prototypes ****************************************************************************/ #undef EXTERN #if defined(__cplusplus) } #endif /**************************************************************************** * Name: lpc31_setup_overcurrent * * Description: * Setup to receive an interrupt-level callback if an overcurrent condition * is detected. * * Input Parameters: * handler - New overcurrent interrupt handler * arg - The argument that will accompany the interrupt * * Returned Value: * Zero (OK) returned on success; a negated errno value is returned on * failure. * ****************************************************************************/ #if 0 /* Not ready yet */ int lpc31_setup_overcurrent(xcpt_t handler, void *arg); #endif #endif /* __ASSEMBLY__ */ #endif /* __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H */