/**************************************************************************** * drivers/wireless/lpwan/sx127x/sx127x.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "sx127x.h" /* TODO: * - OOK communication (RX+TX) doesn't work yet * - Channel Activity Detection (CAD) for LORA * - frequency hopping for LORA and FSK/OOK * - modulation shaping for FSK/OOK * - support for long payload for FSK/OOK (len > FIFO size) * - address filtering for FSK/OOK */ /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ #if !defined(CONFIG_SCHED_HPWORK) # error SX127X requires CONFIG_SCHED_HPWORK #endif /* Configuration ************************************************************/ /* Device name */ #define SX127X_DEV_NAME "/dev/sx127x" /* Payload fixlen default */ #define SX127X_RX_FIXLEN_DEFAULT (0xff) /* Calibration frequency */ #define SX127X_FREQ_CALIBRATION (CONFIG_LPWAN_SX127X_RFFREQ_DEFAULT) /* FSK default frequency deviation is 5kHz */ #define SX127X_FDEV_DEFAULT (5000) /* FSK/OOK bitrate default */ #define SX127X_FOM_BITRATE_DEFAULT (4800) /* FSK/OOK bandwidth default */ #define SX127X_FSKOOK_RXBW_DEFAULT FSKOOK_BANDWIDTH_15P6KHZ #define SX127X_FSKOOK_AFCBW_DEFAULT FSKOOK_BANDWIDTH_20P8KHZ /* Default LORA bandwidth */ #define SX127X_LRM_BW_DEFAULT LORA_BANDWIDTH_7P8KHZ /* Default SF for LORA */ #define SX127X_LRM_SF_DEFAULT (7) /* FSK/OOK RX/TX FIFO size (two separate FIFOs) */ #define SX127X_FOM_FIFO_LEN (64) /* LORA RX/TX FIFO size (one FIFO) */ #define SX127X_LRM_FIFO_LEN (256) /* LORA maximum payload length */ #define SX127X_LRM_PAYLOADMAX_DEFAULT (0xff) /* FSK/OOK default shaping configuration */ #define SX127X_FSKOOK_SHAPING_DEFAULT SX127X_CMN_PARAMP_SHAPING_NONE /* FSK/OOK default PARAMP configuration */ #define SX127X_FSKOOK_PARAMP_DEFAULT SX127X_CMN_PARAMP_PARAMP_40us /* Default code rate for LORA */ #define SX127X_LRM_CR_DEFAULT LORA_CR_4d5 /* Default IDLE mode */ #define SX127X_IDLE_OPMODE SX127X_OPMODE_STANDBY /* Total size for local RX FIFO */ #define SX127X_RXFIFO_TOTAL_SIZE (SX127X_RXFIFO_ITEM_SIZE*CONFIG_LPWAN_SX127X_RXFIFO_LEN) /* Some assertions */ #ifdef CONFIG_LPWAN_SX127X_FSKOOK # warning OOK support is not complete, RX+TX does not work yet! # if CONFIG_LPWAN_SX127X_RXFIFO_DATA_LEN > SX127X_FOM_FIFO_LEN # warning RX data length limited by chip RX FIFO size (FSK/OOK = 64, LORA = 256) # endif #endif /**************************************************************************** * Private Data Types ****************************************************************************/ /* SPI access mode */ typedef enum { MODE_READ, MODE_WRITE } sx127x_access_mode_t; /* SX127X modulation specific ops */ struct sx127x_dev_s; struct sx127x_priv_ops_s { /* Initialize configuration for modulation */ CODE void (*init)(FAR struct sx127x_dev_s *dev); /* Process IRQ 0 */ CODE int (*isr0_process)(FAR struct sx127x_dev_s *dev); /* Operation mode initialization */ CODE int (*opmode_init)(FAR struct sx127x_dev_s *dev, uint8_t opmode); /* Change operation mode */ CODE int (*opmode_set)(FAR struct sx127x_dev_s *dev, uint8_t opmode); /* Set preamble length */ CODE void (*preamble_set)(FAR struct sx127x_dev_s *dev, uint32_t len); /* Get preamble length */ CODE int (*preamble_get)(FAR struct sx127x_dev_s *dev); /* Get current RSSI */ CODE int16_t (*rssi_get)(FAR struct sx127x_dev_s *dev); /* Set sync word */ CODE int (*syncword_set)(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len); /* Get sync word */ CODE void (*syncword_get)(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len); #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT /* Send packet */ CODE int (*send)(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen); #endif #ifdef CONFIG_DEBUG_WIRELESS_INFO /* Dump registers for given modulation */ CODE void (*dumpregs)(FAR struct sx127x_dev_s *dev); #endif }; #ifdef CONFIG_LPWAN_SX127X_FSKOOK /* FSK/OOK private data */ struct sx127x_fskook_s { uint32_t bitrate; /* Bitrate */ uint32_t fdev; /* Frequency deviation */ uint8_t rx_bw; /* RX bandwidth */ uint8_t afc_bw; /* AFC bandwidth */ uint8_t addr_node; /* Node address used in address filtering */ uint8_t addr_brdcast; /* Broadcast address used int address filtering */ bool fixlen; /* Fix length */ bool addr_fltr; /* TODO: Address filtering */ bool seqon; /* Sequencer enabled */ }; #endif #ifdef CONFIG_LPWAN_SX127X_LORA /* LORA private data */ struct sx127x_lora_s { uint32_t freqhop; /* Frequency hopping (not supported) */ uint8_t bw; /* LORA banwidth */ uint8_t sf; /* Spreading factor */ uint8_t cr; /* Coding rate */ bool implicthdr; /* Implicit header mode ON */ bool invert_iq; /* Invert I and Q signals */ }; #endif /* SX127X private data */ struct sx127x_dev_s { /* Reference to SPI bus device */ FAR struct spi_dev_s *spi; /* Low-level MCU-specific support */ FAR const struct sx127x_lower_s *lower; /* Operations specific for selected modulation scheme */ struct sx127x_priv_ops_s ops; struct work_s irq0_work; /* Interrupt DIO0 handling "bottom half" */ uint32_t freq; /* RF carrier frequency */ uint8_t modulation; /* Current modulation (LORA/FSK/OOK) */ uint8_t opmode; /* Current operation mode */ uint8_t idle; /* IDLE opmode */ bool crcon; /* TX/RX CRC enable */ bool rx_cont; /* RX in continuous mode (not supported) */ bool tx_cont; /* TX in continuous mode (not supported) */ #ifdef CONFIG_LPWAN_SX127X_FSKOOK struct sx127x_fskook_s fskook; /* FSK/OOK modulation specific data */ #endif #ifdef CONFIG_LPWAN_SX127X_LORA struct sx127x_lora_s lora; /* LORA modulation specific data */ #endif #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT sem_t tx_sem; /* Wait for availability of send data */ uint32_t tx_timeout; /* TX timeout (not supported) */ int8_t power; /* TX power */ bool pa_force; /* Force PA BOOST pin select */ #endif #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT uint32_t rx_timeout; /* RX timeout (not supported) */ uint16_t rx_fifo_len; /* Number of bytes stored in fifo */ uint16_t nxt_read; /* Next read index */ uint16_t nxt_write; /* Next write index */ /* Circular RX packet buffer */ uint8_t rx_buffer[SX127X_RXFIFO_TOTAL_SIZE]; sem_t rx_sem; /* Wait for availability of received data */ sem_t rx_buffer_sem; /* Protect access to rx fifo */ #endif uint8_t nopens; /* Number of times the device has been opened */ sem_t dev_sem; /* Ensures exclusive access to this structure */ FAR struct pollfd *pfd; /* Polled file descr (or NULL if any) */ }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* Low-level SPI helpres */ static void sx127x_lock(FAR struct spi_dev_s *spi); static void sx127x_unlock(FAR struct spi_dev_s *spi); static uint8_t sx127x_readregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg); static void sx127x_writeregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg, uint8_t value); static uint8_t sx127x_modregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg, uint8_t setbits, uint8_t clrbits); /* LORA specific functions */ #ifdef CONFIG_LPWAN_SX127X_LORA static void sx127x_lora_init(FAR struct sx127x_dev_s *dev); static int16_t sx127x_lora_rssi_get(FAR struct sx127x_dev_s *dev); static int16_t sx127x_lora_rssi_correct(FAR struct sx127x_dev_s *dev, uint32_t freq, int8_t snr, uint8_t regval); static void sx127x_lora_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len); static int sx127x_lora_preamble_get(FAR struct sx127x_dev_s *dev); static int sx127x_lora_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode); static int sx127x_lora_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode); static int sx127x_lora_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len); static void sx127x_lora_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t *len); # ifdef CONFIG_LPWAN_SX127X_RXSUPPORT static int8_t sx127x_lora_snr_get(FAR struct sx127x_dev_s *dev); static int16_t sx127x_lora_pckrssi_get(FAR struct sx127x_dev_s *dev, int8_t snr); static size_t sx127x_lora_rxhandle(FAR struct sx127x_dev_s *dev); # endif # ifdef CONFIG_LPWAN_SX127X_TXSUPPORT static int sx127x_lora_send(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen); # endif # ifdef CONFIG_DEBUG_WIRELESS_INFO static void sx127x_lora_dumpregs(FAR struct sx127x_dev_s *dev); # endif #endif /* FSK/OOK specific functions */ #ifdef CONFIG_LPWAN_SX127X_FSKOOK static void sx127x_fskook_init(FAR struct sx127x_dev_s *dev); static int sx127x_fskook_fdev_set(FAR struct sx127x_dev_s *dev, uint32_t freq); static int16_t sx127x_fskook_rssi_get(FAR struct sx127x_dev_s *dev); static int sx127x_fskook_bitrate_set(FAR struct sx127x_dev_s *dev, uint32_t bitrate); static void sx127x_fskook_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len); static int sx127x_fskook_preamble_get(FAR struct sx127x_dev_s *dev); static int sx127x_fskook_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode); static int sx127x_fskook_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len); static void sx127x_fskook_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len); # ifdef CONFIG_LPWAN_SX127X_RXSUPPORT static size_t sx127x_fskook_rxhandle(FAR struct sx127x_dev_s *dev); # endif # ifdef CONFIG_LPWAN_SX127X_TXSUPPORT static int sx127x_fskook_send(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen); # endif # ifdef CONFIG_DEBUG_WIRELESS_INFO static void sx127x_fskook_dumpregs(FAR struct sx127x_dev_s *dev); # endif #endif /* Common for FSK/OOK and LORA */ static int sx127x_fskook_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode); static int sx127x_init(FAR struct sx127x_dev_s *dev); static int sx127x_deinit(FAR struct sx127x_dev_s *dev); static int sx127x_unregister(FAR struct sx127x_dev_s *dev); static inline int sx127x_attachirq0(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg); static int sx127x_irq0handler(int irq, FAR void *context, FAR void *arg); static int sx127x_modulation_set(FAR struct sx127x_dev_s *dev, uint8_t modulation); static uint8_t sx127x_modulation_get(FAR struct sx127x_dev_s *dev); static int16_t sx127x_rssi_get(FAR struct sx127x_dev_s *dev); static int sx127x_frequency_set(FAR struct sx127x_dev_s *dev, uint32_t freq); static uint32_t sx127x_frequency_get(FAR struct sx127x_dev_s *dev); static int sx127x_power_set(FAR struct sx127x_dev_s *dev, int8_t power); static int8_t sx127x_power_get(FAR struct sx127x_dev_s *dev); static void sx127x_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len); static int sx127x_preamble_get(FAR struct sx127x_dev_s *dev); static int sx127x_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode); static uint8_t sx127x_opmode_get(FAR struct sx127x_dev_s *dev); static int sx127x_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode); static int sx127x_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len); static void sx127x_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len); #ifdef CONFIG_DEBUG_WIRELESS_INFO static void sx127x_dumpregs(FAR struct sx127x_dev_s *dev); #else # define sx127x_dumpregs(x) #endif static bool sx127x_channel_scan(FAR struct sx127x_dev_s *dev, FAR struct sx127x_chanscan_ioc_s *chanscan); static uint32_t sx127x_random_get(FAR struct sx127x_dev_s *dev); #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT static int sx127x_txfifo_write(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen); #endif #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT static ssize_t sx127x_rxfifo_get(struct sx127x_dev_s *dev, FAR uint8_t *buffer, size_t buflen); static void sx127x_rxfifo_put(struct sx127x_dev_s *dev, FAR uint8_t *buffer, size_t buflen); #endif /* POSIX API */ static int sx127x_open(FAR struct file *filep); static int sx127x_close(FAR struct file *filep); static ssize_t sx127x_read(FAR struct file *filep, FAR char *buffer, size_t buflen); static ssize_t sx127x_write(FAR struct file *filep, FAR const char *buffer, size_t buflen); static int sx127x_ioctl(FAR struct file *filep, int cmd, unsigned long arg); static int sx127x_poll(FAR struct file *filep, FAR struct pollfd *fds, bool setup); /**************************************************************************** * Private Data ****************************************************************************/ /* Only one device is supported for now */ static struct sx127x_dev_s g_sx127x_devices[1]; /* File ops */ static const struct file_operations sx127x_fops = { sx127x_open, /* open */ sx127x_close, /* close */ sx127x_read, /* read */ sx127x_write, /* write */ NULL, /* seek */ sx127x_ioctl, /* ioctl */ sx127x_poll /* poll */ #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS , NULL /* unlink */ #endif }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: sx127x_lock * * Description: * Acquire exclusive access to the shared SPI bus. * ****************************************************************************/ static void sx127x_lock(FAR struct spi_dev_s *spi) { SPI_LOCK(spi, 1); SPI_SETBITS(spi, 8); SPI_SETMODE(spi, SPIDEV_MODE0); SPI_SETFREQUENCY(spi, CONFIG_LPWAN_SX127X_SPIFREQ); } /**************************************************************************** * Name: sx127x_unlock * * Description: * Release exclusive access to the shared SPI bus. * ****************************************************************************/ static void sx127x_unlock(FAR struct spi_dev_s *spi) { SPI_LOCK(spi, 0); } /**************************************************************************** * Name: sx127x_select ****************************************************************************/ static inline void sx127x_select(struct sx127x_dev_s * dev) { SPI_SELECT(dev->spi, SPIDEV_LPWAN(0), true); } /**************************************************************************** * Name: sx127x_deselect ****************************************************************************/ static inline void sx127x_deselect(struct sx127x_dev_s * dev) { SPI_SELECT(dev->spi, SPIDEV_LPWAN(0), false); } /**************************************************************************** * Name: sx127x_access ****************************************************************************/ static uint8_t sx127x_access(FAR struct sx127x_dev_s *dev, sx127x_access_mode_t mode, uint8_t cmd, FAR uint8_t *buf, int length) { uint8_t status = 0; /* Prepare SPI */ sx127x_select(dev); /* Transfer */ status = SPI_SEND(dev->spi, cmd); switch (mode) { case MODE_WRITE: { if (length > 0) { SPI_SNDBLOCK(dev->spi, buf, length); } break; } case MODE_READ: { SPI_RECVBLOCK(dev->spi, buf, length); break; } default: { wlerr("ERROR: unknown SPI access mode %d!\n", mode); break; } } sx127x_deselect(dev); return status; } /**************************************************************************** * Name: sx127x_readreg * * Description: * Read register from sx127x * ****************************************************************************/ static inline uint8_t sx127x_readreg(FAR struct sx127x_dev_s *dev, uint8_t reg, FAR uint8_t *value, int len) { return sx127x_access(dev, MODE_READ, reg | SX127X_R_REGISTER, value, len); } /**************************************************************************** * Name: sx127x_readregbyte * * Description: * Read single byte value from a register of sx127x * ****************************************************************************/ static inline uint8_t sx127x_readregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg) { uint8_t val = 0; sx127x_readreg(dev, reg, &val, 1); return val; } /**************************************************************************** * Name: sx127x_writereg * * Description: * Write value to a register of sx127x * ****************************************************************************/ static inline int sx127x_writereg(FAR struct sx127x_dev_s *dev, uint8_t reg, FAR const uint8_t *value, int len) { return sx127x_access(dev, MODE_WRITE, reg | SX127X_W_REGISTER, (FAR uint8_t *)value, len); } /**************************************************************************** * Name: sx127x_writeregbyte * * Description: * Write single byte value to a register of sx127x * ****************************************************************************/ static inline void sx127x_writeregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg, uint8_t value) { sx127x_writereg(dev, reg, &value, 1); } /**************************************************************************** * Name: sx127x_modreg * * Description: * Modify register value of sx127x * ****************************************************************************/ static uint8_t sx127x_modregbyte(FAR struct sx127x_dev_s *dev, uint8_t reg, uint8_t setbits, uint8_t clrbits) { uint8_t val = 0; sx127x_readreg(dev, reg, &val, 1); val &= ~clrbits; val |= setbits; sx127x_writereg(dev, reg, &val, 1); return val; } /**************************************************************************** * Name: sx127x_attachirq0 ****************************************************************************/ static inline int sx127x_attachirq0(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq0attach(isr, arg); } /**************************************************************************** * Name: sx127x_attachirq1 ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_DIO1 static inline int sx127x_attachirq1(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq1attach(isr, arg); } #endif /**************************************************************************** * Name: sx127x_attachirq2 ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_DIO2 static inline int sx127x_attachirq2(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq2attach(isr, arg); } #endif /**************************************************************************** * Name: sx127x_attachirq3 ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_DIO3 static inline int sx127x_attachirq3(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq3attach(isr, arg); } #endif /**************************************************************************** * Name: sx127x_attachirq4 ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_DIO4 static inline int sx127x_attachirq4(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq4attach(isr, arg); } #endif /**************************************************************************** * Name: sx127x_attachirq5 ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_DIO5 static inline int sx127x_attachirq5(FAR struct sx127x_dev_s *dev, xcpt_t isr, FAR void *arg) { return dev->lower->irq5attach(isr, arg); } #endif /**************************************************************************** * Name: sx127x_reset * * Description: * Reset radio * ****************************************************************************/ static void sx127x_reset(FAR struct sx127x_dev_s *dev) { dev->lower->reset(); } /**************************************************************************** * Name: sx127x_open * * Description: * This function is called whenever the SX127X device is opened. * ****************************************************************************/ static int sx127x_open(FAR struct file *filep) { FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; wlinfo("Opening sx127x dev\n"); DEBUGASSERT(filep); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; /* Get exclusive access to the driver data structure */ ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } /* Check if device is not already used */ if (dev->nopens > 0) { ret = -EBUSY; goto errout; } /* Initialize device */ ret = sx127x_init(dev); if (ret < 0) { wlerr("ERROR: failed to initialize sx127x\n"); goto errout; } dev->nopens++; errout: nxsem_post(&dev->dev_sem); return ret; } /**************************************************************************** * Name: sx127x_close * * Description: * This routine is called when the SX127X device is closed. * It waits for the last remaining data to be sent. * ****************************************************************************/ static int sx127x_close(FAR struct file *filep) { FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; wlinfo("Closing sx127x dev\n"); DEBUGASSERT(filep); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; /* Get exclusive access to the driver data structure */ ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } ret = sx127x_deinit(dev); if (ret < 0) { wlerr("ERROR: failed to deinit sx127x\n"); } dev->nopens--; nxsem_post(&dev->dev_sem); return OK; } /**************************************************************************** * Name: sx127x_read * * Description: * Standard driver read method * ****************************************************************************/ static ssize_t sx127x_read(FAR struct file *filep, FAR char *buffer, size_t buflen) { #ifndef CONFIG_LPWAN_SX127X_RXSUPPORT return -ENOSYS; #else FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; DEBUGASSERT(filep); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } if ((filep->f_oflags & O_NONBLOCK) != 0) { nxsem_trywait(&dev->rx_sem); ret = 0; } else { ret = nxsem_wait(&dev->rx_sem); } if (ret < 0) { return ret; } /* Get RX data from fifo */ ret = sx127x_rxfifo_get(dev, (uint8_t *)buffer, buflen); nxsem_post(&dev->dev_sem); return ret; #endif } /**************************************************************************** * Name: sx127x_write * * Description: * Standard driver write method. * ****************************************************************************/ static ssize_t sx127x_write(FAR struct file *filep, FAR const char *buffer, size_t buflen) { #ifndef CONFIG_LPWAN_SX127X_TXSUPPORT return -ENOSYS; #else FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; DEBUGASSERT(filep); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } wlinfo("buflen=%d \n", buflen); /* Change mode to STANDBY */ sx127x_opmode_set(dev, SX127X_OPMODE_STANDBY); /* Initialize TX mode */ ret = sx127x_opmode_init(dev, SX127X_OPMODE_TX); if (ret < 0) { /* Restore IDLE mode settings */ sx127x_opmode_init(dev, dev->idle); wlerr("Failed to initialize TX mode!\n"); ret = -EINVAL; goto errout; } /* Call modulation specific send */ ret = dev->ops.send(dev, (uint8_t *)buffer, buflen); /* Change mode to TX to start data transfer */ sx127x_opmode_set(dev, SX127X_OPMODE_TX); /* Wait for TXDONE */ nxsem_wait(&dev->tx_sem); errout: /* Change mode to IDLE after transfer * NOTE: if sequencer for FSK/OOK is ON - this should be done automatically */ sx127x_opmode_set(dev, dev->idle); nxsem_post(&dev->dev_sem); return ret; #endif } /**************************************************************************** * Name: sx127x_ioctl * * Description: * Standard driver ioctl method. * ****************************************************************************/ static int sx127x_ioctl(FAR struct file *filep, int cmd, unsigned long arg) { FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; wlinfo("cmd: %d arg: %ld\n", cmd, arg); DEBUGASSERT(filep); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; /* Get exclusive access to the driver data structure */ ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } /* Process the IOCTL by command */ switch (cmd) { /* Set radio frequency. Arg: Pointer to uint32_t frequency value in * Hz. */ case WLIOC_SETRADIOFREQ: { FAR uint32_t *ptr = (FAR uint32_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); sx127x_frequency_set(dev, *ptr); break; } /* Get current radio frequency. arg: Pointer to uint32_t frequency * value in Hz. */ case WLIOC_GETRADIOFREQ: { FAR int8_t *ptr = (FAR int8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_frequency_get(dev); break; } /* Set TX power. arg: Pointer to int8_t power value */ case WLIOC_SETTXPOWER: { FAR int8_t *ptr = (FAR int8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); sx127x_power_set(dev, *ptr); break; } /* Get current TX power. arg: Pointer to int8_t power value */ case WLIOC_GETTXPOWER: { FAR int8_t *ptr = (FAR int8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_power_get(dev); break; } /* Get RSSI */ case SX127XIOC_RSSIGET: { FAR int16_t *ptr = (FAR int16_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_rssi_get(dev); break; } /* Set modulation */ case SX127XIOC_MODULATIONSET: { FAR uint8_t *ptr = (FAR uint8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); ret = sx127x_modulation_set(dev, *ptr); break; } /* Get modulation */ case SX127XIOC_MODULATIONGET: { FAR uint8_t *ptr = (FAR uint8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_modulation_get(dev); break; } /* Operation mode set */ case SX127XIOC_OPMODESET: { FAR uint8_t *ptr = (FAR uint8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); ret = sx127x_opmode_set(dev, *ptr); break; } /* Operation mode get */ case SX127XIOC_OPMODEGET: { FAR uint8_t *ptr = (FAR uint8_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_opmode_get(dev); break; } /* Channel scan */ case SX127XIOC_CHANSCAN: { FAR struct sx127x_chanscan_ioc_s *ptr = (FAR struct sx127x_chanscan_ioc_s *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); sx127x_channel_scan(dev, ptr); break; } /* Preamble length set */ case SX127XIOC_PREAMBLESET: { FAR int *ptr = (FAR int *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); sx127x_preamble_set(dev, *ptr); break; } /* Preamble length get */ case SX127XIOC_PREAMBLEGET: { FAR int *ptr = (FAR int *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_preamble_get(dev); break; } /* SyncWord set */ case SX127XIOC_SYNCWORDSET: { ASSERT(0); sx127x_syncword_set(dev, NULL, 0); break; } /* SyncWord get */ case SX127XIOC_SYNCWORDGET: { ASSERT(0); sx127x_syncword_get(dev, NULL, 0); break; } /* Get random number based on RSSI */ case SX127XIOC_RANDOMGET: { FAR uint32_t *ptr = (FAR uint32_t *)((uintptr_t)arg); DEBUGASSERT(ptr != NULL); *ptr = sx127x_random_get(dev); break; } default: { ret = -ENOTTY; break; } } nxsem_post(&dev->dev_sem); return ret; } /**************************************************************************** * Name: sx127x_poll * * Description: * Standard driver poll method. * ****************************************************************************/ static int sx127x_poll(FAR struct file *filep, FAR struct pollfd *fds, bool setup) { #ifndef CONFIG_LPWAN_SX127X_RXSUPPORT return -ENOSYS; #else FAR struct sx127x_dev_s *dev = NULL; FAR struct inode *inode = NULL; int ret = 0; wlinfo("setup: %d\n", (int)setup); DEBUGASSERT(filep && fds); inode = filep->f_inode; DEBUGASSERT(inode && inode->i_private); dev = (FAR struct sx127x_dev_s *)inode->i_private; /* Exclusive access */ ret = nxsem_wait(&dev->dev_sem); if (ret < 0) { return ret; } /* Are we setting up the poll? Or tearing it down? */ if (setup) { /* Ignore waits that do not include POLLIN */ if ((fds->events & POLLIN) == 0) { ret = -EDEADLK; goto errout; } /* Check if we can accept this poll. * For now, only one thread can poll the device at any time * (shorter / simpler code) */ if (dev->pfd) { ret = -EBUSY; goto errout; } dev->pfd = fds; /* Is there is already data in the fifo? then trigger POLLIN now - * don't wait for RX. */ nxsem_wait(&dev->rx_buffer_sem); if (dev->rx_fifo_len > 0) { /* Data available for input */ dev->pfd->revents |= POLLIN; nxsem_post(dev->pfd->sem); } nxsem_post(&dev->rx_buffer_sem); } else /* Tear it down */ { dev->pfd = NULL; } errout: nxsem_post(&dev->dev_sem); return ret; #endif } /**************************************************************************** * Name: sx127x_lora_isr0_process * * Description: * Handle DIO0 interrupt for LORA radio * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_LORA static int sx127x_lora_isr0_process(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT bool data_valid = true; #endif uint8_t irq = 0; int ret = OK; /* Get IRQ */ sx127x_lock(dev->spi); irq = sx127x_readregbyte(dev, SX127X_LRM_IRQ); sx127x_unlock(dev->spi); wlinfo("ISR0: IRQ = 0x%02x\n", irq); switch (dev->opmode) { #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT /* TX DONE */ case SX127X_OPMODE_TX: { /* Release TX sem */ nxsem_post(&dev->tx_sem); /* Clear TX interrupt */ irq = SX127X_LRM_IRQ_TXDONE; break; } #endif /* CONFIG_LPWAN_SX127X_TXSUPPORT */ #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT /* RX DONE */ case SX127X_OPMODE_RX: case SX127X_OPMODE_RXSINGLE: { /* REVISIT: Always check PAYLOADCRCERR even CRCONPAYLOAD not set */ if ((irq & SX127X_LRM_IRQ_PAYLOADCRCERR) != 0) { data_valid = false; } if (data_valid) { ret = sx127x_lora_rxhandle(dev); if (ret > 0) { if (dev->pfd) { /* Data available for input */ dev->pfd->revents |= POLLIN; wlinfo("Wake up polled fd\n"); nxsem_post(dev->pfd->sem); } /* Wake-up any thread waiting in recv */ nxsem_post(&dev->rx_sem); } } else { /* RX Data invalid */ wlinfo("Invalid LORA RX data!\n"); } /* After receiving the data in RXSINGLE mode the chip goes into * STANBY mode */ if (dev->opmode == SX127X_OPMODE_RXSINGLE) { dev->opmode = SX127X_OPMODE_STANDBY; } /* Clear RX interrupts */ irq = (SX127X_LRM_IRQ_RXDONE | SX127X_LRM_IRQ_PAYLOADCRCERR | SX127X_LRM_IRQ_VALIDHDR); break; } #endif /* CONFIG_LPWAN_SX127X_RXSUPPORT */ /* Only LORA - CAD DONE */ case SX127X_OPMODE_CAD: { /* TODO */ wlerr("TODO: ISR0 in CAD mode not implemented yet!\n"); /* Clear CAD interrupt */ irq = SX127X_LRM_IRQ_CADDONE; break; } default: { wlwarn("WARNING: Interrupt not processed, opmode=%d\n", dev->opmode); ret = -EINVAL; break; } } /* Clear interrupts */ sx127x_lock(dev->spi); sx127x_writeregbyte(dev, SX127X_LRM_IRQ, irq); sx127x_unlock(dev->spi); return ret; } #endif /* CONFIG_LPWAN_SX127X_LORA */ /**************************************************************************** * Name: sx127x_fskook_isr0_process * * Description: * Handle DIO0 interrupt for FSK/OOK radio * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_FSKOOK static int sx127x_fskook_isr0_process(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT bool data_valid = true; #endif uint8_t irq1 = 0; uint8_t irq2 = 0; int ret = OK; /* Get IRQ1 and IRQ2 */ sx127x_lock(dev->spi); irq1 = sx127x_readregbyte(dev, SX127X_FOM_IRQ1); irq2 = sx127x_readregbyte(dev, SX127X_FOM_IRQ2); sx127x_unlock(dev->spi); wlinfo("ISR0: IRQ1 = 0x%02x, IRQ2 = 0x%02x\n", irq1, irq2); switch (dev->opmode) { #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT /* TX DONE */ case SX127X_OPMODE_TX: { /* Release TX sem */ nxsem_post(&dev->tx_sem); break; } #endif /* CONFIG_LPWAN_SX127X_TXSUPPORT */ #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT /* RX DONE */ case SX127X_OPMODE_RX: { /* RX data valid ? */ if (dev->crcon == true && (irq2 & SX127X_FOM_IRQ2_CRCOK) == 0) { data_valid = false; } if (data_valid == true) { /* RX data valid */ ret = sx127x_fskook_rxhandle(dev); if (ret > 0) { if (dev->pfd) { /* Data available for input */ dev->pfd->revents |= POLLIN; wlinfo("Wake up polled fd\n"); nxsem_post(dev->pfd->sem); } /* Wake-up any thread waiting in recv */ nxsem_post(&dev->rx_sem); } } else { /* RX Data invalid */ wlinfo("Invalid FSK/OOK RX data!\n"); } /* TODO: restart RX if continuous mode */ break; } #endif /* CONFIG_LPWAN_SX127X_RXSUPPORT */ default: { wlwarn("WARNING: Interrupt not processed\n"); ret = -EINVAL; break; } } /* REVISIT: clear interrupts */ irq1 = (SX127X_FOM_IRQ1_RSSI | SX127X_FOM_IRQ1_PREAMBE | SX127X_FOM_IRQ1_SYNCADDRMATCH); irq2 = SX127X_FOM_IRQ2_FIFOOVR; sx127x_lock(dev->spi); sx127x_writeregbyte(dev, SX127X_FOM_IRQ1, irq1); sx127x_writeregbyte(dev, SX127X_FOM_IRQ2, irq2); sx127x_unlock(dev->spi); return ret; } #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ /**************************************************************************** * Name: sx127x_isr0_process * * Description: * Handle DIO0 interrupt for LORA radio * ****************************************************************************/ static void sx127x_isr0_process(FAR void *arg) { DEBUGASSERT(arg); FAR struct sx127x_dev_s *dev = (struct sx127x_dev_s *)arg; int ret = OK; /* Return immediately if isr0_process is not initialized */ if (dev->ops.isr0_process == NULL) { return; } /* isr0_process depends on the current modulation scheme */ ret = dev->ops.isr0_process(dev); if (ret < 0) { wlerr("Failed to process ISR0 %d\n", ret); } } /**************************************************************************** * Name: sx127x_irq0handler ****************************************************************************/ static int sx127x_irq0handler(int irq, FAR void *context, FAR void *arg) { FAR struct sx127x_dev_s *dev = (FAR struct sx127x_dev_s *)arg; DEBUGASSERT(dev != NULL); DEBUGASSERT(work_available(&dev->irq0_work)); return work_queue(HPWORK, &dev->irq0_work, sx127x_isr0_process, arg, 0); } #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT /**************************************************************************** * Name: sx127x_fskook_rxhandle * * Description: * Receive data from FIFO for FSK/OOK radio * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_FSKOOK static size_t sx127x_fskook_rxhandle(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); struct sx127x_read_hdr_s rxdata; uint8_t datalen = 0; size_t len = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get data from chip fifo */ if (dev->fskook.fixlen == true) { /* Fixed packet length hardcoded */ datalen = SX127X_RX_FIXLEN_DEFAULT; } else { /* First byte is payload length */ datalen = sx127x_readregbyte(dev, SX127X_CMN_FIFO); } /* Ignore packets with unsupported data length */ if (datalen > SX127X_READ_DATA_MAX) { wlerr("Unsupported data length! %d > %d\n", datalen, SX127X_READ_DATA_MAX); sx127x_unlock(dev->spi); goto errout; } /* Read payload and store */ sx127x_readreg(dev, SX127X_CMN_FIFO, rxdata.data, datalen); /* Unlock SPI */ sx127x_unlock(dev->spi); /* No RX SNR data for FSK/OOK */ rxdata.snr = 0; /* Store last RSSI */ rxdata.rssi = sx127x_fskook_rssi_get(dev); /* Store packet length */ rxdata.datalen = datalen; /* Total length */ len = datalen + SX127X_READ_DATA_HEADER_LEN; /* Put data on local fifo */ sx127x_rxfifo_put(dev, (uint8_t *)&rxdata, len); errout: /* Return total length */ return len; } #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ /**************************************************************************** * Name: sx127x_lora_rxhandle * * Description: * Receive data from FIFO for LORA radio * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_LORA static size_t sx127x_lora_rxhandle(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); struct sx127x_read_hdr_s rxdata; size_t len = 0; uint8_t datalen = 0; uint8_t rx_ptr = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get payload length */ datalen = sx127x_readregbyte(dev, SX127X_LRM_RXBYTES); /* Ignore packets with unsupported data length */ if (datalen > SX127X_READ_DATA_MAX) { wlerr("Unsupported data length! %d > %d\n", datalen, SX127X_READ_DATA_MAX); sx127x_unlock(dev->spi); goto errout; } /* Get start address of last packet received */ rx_ptr = sx127x_readregbyte(dev, SX127X_LRM_RXCURR); /* Set FIFO pointer */ sx127x_writeregbyte(dev, SX127X_LRM_ADDRPTR, rx_ptr); /* Read payload */ sx127x_readreg(dev, SX127X_CMN_FIFO, rxdata.data, datalen); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Store last RX SNR */ rxdata.snr = sx127x_lora_snr_get(dev); /* Store last RX RSSI */ rxdata.rssi = sx127x_lora_pckrssi_get(dev, rxdata.snr); /* Store packet length */ rxdata.datalen = datalen; /* Total length */ len = datalen + SX127X_READ_DATA_HEADER_LEN; /* Put data on local fifo */ sx127x_rxfifo_put(dev, (uint8_t *)&rxdata, len); errout: /* Return total length */ return len; } #endif /* CONFIG_LPWAN_SX127X_LORA */ /**************************************************************************** * Name: sx127x_rxfifo_get * * Description: * Get data from RX FIFO * ****************************************************************************/ static ssize_t sx127x_rxfifo_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *buffer, size_t buflen) { FAR struct sx127x_read_hdr_s *pkt = NULL; size_t i = 0; size_t pktlen = 0; size_t ret = 0; ret = nxsem_wait(&dev->rx_buffer_sem); if (ret < 0) { return ret; } /* No data on RX FIFO */ if (dev->rx_fifo_len == 0) { pktlen = 0; goto no_data; } /* Get packet header */ pkt = (struct sx127x_read_hdr_s *) (dev->rx_buffer + dev->nxt_read * SX127X_RXFIFO_ITEM_SIZE); /* Packet length is data length + header length */ pktlen = pkt->datalen + SX127X_READ_DATA_HEADER_LEN; /* Get packet from FIFO */ for (i = 0; i < pktlen && i < SX127X_RXFIFO_ITEM_SIZE; i += 1) { buffer[i] = dev->rx_buffer[dev->nxt_read * SX127X_RXFIFO_ITEM_SIZE + i]; } dev->nxt_read = (dev->nxt_read + 1) % CONFIG_LPWAN_SX127X_RXFIFO_LEN; dev->rx_fifo_len--; ret = pktlen; no_data: nxsem_post(&dev->rx_buffer_sem); return ret; } /**************************************************************************** * Name: sx127x_rxfifo_put * * Description: * Put packet data on RX FIFO * ****************************************************************************/ static void sx127x_rxfifo_put(FAR struct sx127x_dev_s *dev, FAR uint8_t *buffer, size_t buflen) { size_t i = 0; int ret = 0; ret = nxsem_wait(&dev->rx_buffer_sem); if (ret < 0) { return; } dev->rx_fifo_len++; if (dev->rx_fifo_len > CONFIG_LPWAN_SX127X_RXFIFO_LEN) { dev->rx_fifo_len = CONFIG_LPWAN_SX127X_RXFIFO_LEN; dev->nxt_read = (dev->nxt_read + 1) % CONFIG_LPWAN_SX127X_RXFIFO_LEN; } /* Put packet on fifo */ for (i = 0; i < (buflen + 1) && i < SX127X_RXFIFO_ITEM_SIZE; i += 1) { dev->rx_buffer[i + dev->nxt_write * SX127X_RXFIFO_ITEM_SIZE] = buffer[i]; } dev->nxt_write = (dev->nxt_write + 1) % CONFIG_LPWAN_SX127X_RXFIFO_LEN; nxsem_post(&dev->rx_buffer_sem); } #endif /* CONFIG_LPWAN_SX127X_RXSUPPORT */ #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT /**************************************************************************** * Name: sx127x_txfifo_write * * Description: * Write data to the SX127X TX FIFO * ****************************************************************************/ static int sx127x_txfifo_write(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen) { /* NOTE: Do not lock SPI here, it should be already locked! */ /* Write buffer to FIFO */ sx127x_writereg(dev, SX127X_CMN_FIFO, data, datalen); return OK; } /**************************************************************************** * Name: sx127x_fskook_send * * Description: * Send data in FSK/OOK radio mode * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_FSKOOK static int sx127x_fskook_send(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); int ret = 0; /* Check payload length */ if (datalen > SX127X_FOM_PAYLOADLEN_MAX) { wlerr("Not supported data len!\n"); ret = -EINVAL; goto errout; } #if 1 /* For now we don't support datalen > FIFO_LEN for FSK/OOK. * For fixlen = true, datalen <= 64 * For fixlen = false, datalen < 64 (we support this for now) */ if (datalen > 63) { wlerr("Not supported data len!\n"); ret = -EINVAL; goto errout; } #endif /* Lock SPI */ sx127x_lock(dev->spi); if (dev->fskook.fixlen == true) { /* Write payload length register (only LSB for now) */ sx127x_writeregbyte(dev, SX127X_FOM_PAYLOADLEN, datalen); } else { /* First byte is length */ ret = sx127x_txfifo_write(dev, (uint8_t *)&datalen, 1); } /* Write payload */ sx127x_txfifo_write(dev, data, datalen); /* Unlock SPI */ sx127x_unlock(dev->spi); errout: return ret; } #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ /**************************************************************************** * Name: sx127x_lora_send * * Description: * Send data in LORA radio mode * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_LORA static int sx127x_lora_send(FAR struct sx127x_dev_s *dev, FAR const uint8_t *data, size_t datalen) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); int ret = 0; /* Check payload length */ if (datalen > SX127X_LRM_PAYLOADLEN_MAX) { wlerr("Not supported data len!\n"); ret = -EINVAL; goto errout; } /* Lock SPI */ sx127x_lock(dev->spi); /* Configure payload length */ sx127x_writeregbyte(dev, SX127X_LRM_PAYLOADLEN, datalen); /* Write payload */ sx127x_txfifo_write(dev, data, datalen); /* Unlock SPI */ sx127x_unlock(dev->spi); errout: return ret; } #endif /* CONFIG_LPWAN_SX127X_LORA */ #endif /* CONFIG_LPWAN_SX127X_TXSUPPORT */ /**************************************************************************** * Name: sx127x_opmode_init * * Description: * Initialize operation mode * ****************************************************************************/ static int sx127x_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode) { int ret = OK; if (opmode == dev->opmode) { goto errout; } /* Board-specific opmode configuration */ ret = dev->lower->opmode_change(opmode); if (ret < 0) { wlerr("Board-specific opmode_change failed %d!\n", ret); goto errout; } /* Initialize opmode */ ret = dev->ops.opmode_init(dev, opmode); if (ret < 0) { wlerr("opmode_init failed %d!\n", ret); goto errout; } errout: return ret; } /**************************************************************************** * Name: sx127x_opmode_set * * Description: * Set operation mode * ****************************************************************************/ static int sx127x_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode) { int ret = OK; wlinfo("opmode_set %d->%d\n", dev->opmode, opmode); if (opmode == dev->opmode) { goto errout; } #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT /* REVISIT: TX is initialized before data send, * but where we should initialize RX ? */ if (opmode != SX127X_OPMODE_TX) { ret = sx127x_opmode_init(dev, opmode); } #endif /* Change mode */ dev->ops.opmode_set(dev, opmode); /* Update local variable */ dev->opmode = opmode; errout: return ret; } /**************************************************************************** * Name: sx127x_opmode_get * * Description: * Get current operation mode * ****************************************************************************/ static uint8_t sx127x_opmode_get(FAR struct sx127x_dev_s *dev) { wlerr("TODO: sx127x_opmode_get not implemented yet\n"); return 0; } /**************************************************************************** * Name: sx127x_lora_opmode_init * * Description: * Initialize operation mode for FSK/OOK. * We need this even if FSK/OOK support is disabled * ****************************************************************************/ static int sx127x_fskook_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); uint8_t dio0map = 0; uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; sx127x_lock(dev->spi); /* Get mode specific configuration */ switch (opmode) { case SX127X_OPMODE_SLEEP: case SX127X_OPMODE_STANDBY: case SX127X_OPMODE_FSRX: case SX127X_OPMODE_FSTX: { break; } case SX127X_OPMODE_TX: { /* Remap DIO0 to RXTX DONE */ dio0map = SX127X_FOM_DIOMAP1_DIO0_RXTX; /* TX start condition on FIFO not empty */ sx127x_writeregbyte(dev, SX127X_FOM_FIFOTHR, SX127X_FOM_FIFOTHR_TXSTARTCOND); break; } case SX127X_OPMODE_RX: { /* Remap DIO0 to RXTX DONE */ dio0map = SX127X_FOM_DIOMAP1_DIO0_RXTX; /* REVISIT: Configure RXCFG register: * - AGC auto ON * - AFC auto ON * - RX trigger on PreableDetect */ setbits = (SX127X_FOM_RXCFG_AGCAUTOON | SX127X_FOM_RXCFG_AFCAUTOON | SX127X_FOM_RXCFG_TRG_PREDET); sx127x_writeregbyte(dev, SX127X_FOM_RXCFG, setbits); break; } default: { wlerr("ERROR: invalid mode %d\n", opmode); ret = -EINVAL; goto errout; } } /* Configure DIO0 pin */ setbits = dio0map; clrbits = SX127X_CMN_DIOMAP1_DIO0_MASK; sx127x_modregbyte(dev, SX127X_CMN_DIOMAP1, setbits, clrbits); sx127x_unlock(dev->spi); errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_opmode_set * * Description: * Set operation mode for FSK/OOK. * We need this even if FSK/OOK support is disabled * ****************************************************************************/ static int sx127x_fskook_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; switch (opmode) { case SX127X_OPMODE_SLEEP: case SX127X_OPMODE_STANDBY: case SX127X_OPMODE_FSRX: case SX127X_OPMODE_FSTX: case SX127X_OPMODE_TX: case SX127X_OPMODE_RX: { /* Do nothing */ break; } default: { wlerr("ERROR: invalid FSK/OOK mode %d\n", opmode); ret = -EINVAL; goto errout; } } sx127x_lock(dev->spi); /* Update mode */ setbits = ((opmode - 1) << SX127X_CMN_OPMODE_MODE_SHIFT); clrbits = SX127X_CMN_OPMODE_MODE_MASK; sx127x_modregbyte(dev, SX127X_CMN_OPMODE, setbits, clrbits); sx127x_unlock(dev->spi); errout: return ret; } #ifdef CONFIG_LPWAN_SX127X_FSKOOK /**************************************************************************** * Name: sx127x_fskook_rxbw_set * * Description: * Set RX BW for FSK/OOK * ****************************************************************************/ static int sx127x_fskook_rxbw_set(FAR struct sx127x_dev_s *dev, uint8_t rx_bw) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); int ret = OK; if (rx_bw == dev->fskook.rx_bw) { goto errout; } switch (rx_bw) { case FSKOOK_BANDWIDTH_2P6KHZ: case FSKOOK_BANDWIDTH_3P1KHZ: case FSKOOK_BANDWIDTH_3P9KHZ: case FSKOOK_BANDWIDTH_5P2KHZ: case FSKOOK_BANDWIDTH_6P3KHZ: case FSKOOK_BANDWIDTH_7P8KHZ: case FSKOOK_BANDWIDTH_10P4KHZ: case FSKOOK_BANDWIDTH_12P5KHZ: case FSKOOK_BANDWIDTH_15P6KHZ: case FSKOOK_BANDWIDTH_20P8KHZ: case FSKOOK_BANDWIDTH_25KHZ: case FSKOOK_BANDWIDTH_31P3KHZ: case FSKOOK_BANDWIDTH_41P7KHZ: case FSKOOK_BANDWIDTH_50KHZ: case FSKOOK_BANDWIDTH_62P5KHZ: case FSKOOK_BANDWIDTH_83P3KHZ: case FSKOOK_BANDWIDTH_100KHZ: case FSKOOK_BANDWIDTH_125KHZ: case FSKOOK_BANDWIDTH_166P7KHZ: case FSKOOK_BANDWIDTH_200KHZ: case FSKOOK_BANDWIDTH_250KHZ: { /* Lock SPI */ sx127x_lock(dev->spi); /* Write register */ sx127x_writeregbyte(dev, SX127X_FOM_RXBW, rx_bw); /* Unlock SPI */ sx127x_unlock(dev->spi); break; } default: { wlerr("Unsupported bandwidth %d\n", rx_bw); ret = -EINVAL; goto errout; } } /* Update local */ dev->fskook.rx_bw = rx_bw; errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_afcbw_set * * Description: * Set AFC BW for FSK/OOK * ****************************************************************************/ static int sx127x_fskook_afcbw_set(FAR struct sx127x_dev_s *dev, uint8_t afc_bw) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); int ret = OK; if (afc_bw == dev->fskook.afc_bw) { goto errout; } switch (afc_bw) { case FSKOOK_BANDWIDTH_2P6KHZ: case FSKOOK_BANDWIDTH_3P1KHZ: case FSKOOK_BANDWIDTH_3P9KHZ: case FSKOOK_BANDWIDTH_5P2KHZ: case FSKOOK_BANDWIDTH_6P3KHZ: case FSKOOK_BANDWIDTH_7P8KHZ: case FSKOOK_BANDWIDTH_10P4KHZ: case FSKOOK_BANDWIDTH_12P5KHZ: case FSKOOK_BANDWIDTH_15P6KHZ: case FSKOOK_BANDWIDTH_20P8KHZ: case FSKOOK_BANDWIDTH_25KHZ: case FSKOOK_BANDWIDTH_31P3KHZ: case FSKOOK_BANDWIDTH_41P7KHZ: case FSKOOK_BANDWIDTH_50KHZ: case FSKOOK_BANDWIDTH_62P5KHZ: case FSKOOK_BANDWIDTH_83P3KHZ: case FSKOOK_BANDWIDTH_100KHZ: case FSKOOK_BANDWIDTH_125KHZ: case FSKOOK_BANDWIDTH_166P7KHZ: case FSKOOK_BANDWIDTH_200KHZ: case FSKOOK_BANDWIDTH_250KHZ: { /* Lock SPI */ sx127x_lock(dev->spi); /* Write register */ sx127x_writeregbyte(dev, SX127X_FOM_AFCBW, afc_bw); /* Unlock SPI */ sx127x_unlock(dev->spi); break; } default: { wlerr("Unsupported bandwidth %d\n", afc_bw); ret = -EINVAL; goto errout; } } /* Update local */ dev->fskook.afc_bw = afc_bw; errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_seq_start ****************************************************************************/ static void sx127x_fskook_seq_start(FAR struct sx127x_dev_s *dev, bool state) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); /* Lock SPI */ sx127x_lock(dev->spi); if (state == true) { /* Start sequencer */ sx127x_modregbyte(dev, SX127X_FOM_SEQCFG1, SX127X_FOM_SEQCFG1_SEQSTART, 0); } else { /* Stop sequencer */ sx127x_modregbyte(dev, SX127X_FOM_SEQCFG1, SX127X_FOM_SEQCFG1_SEQSTOP, 0); } /* Unlock SPI */ sx127x_unlock(dev->spi); /* Store sequencer state */ dev->fskook.seqon = state; } /**************************************************************************** * Name: sx127x_fskook_seq_init * * Description: * Initialize FSK/OOK sequencer. * This can be used to automate transitions between operation modes and * thus further reduce energy consumption. * ****************************************************************************/ static int sx127x_fskook_seq_init(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); uint8_t seq1 = 0; uint8_t seq2 = 0; int ret = OK; /* Need sleep mode or standby mode */ if (dev->opmode > SX127X_OPMODE_STANDBY) { sx127x_opmode_set(dev, SX127X_OPMODE_STANDBY); } /* Nothing here */ seq1 = 0; seq2 = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Write registers */ sx127x_writeregbyte(dev, SX127X_FOM_SEQCFG1, seq1); sx127x_writeregbyte(dev, SX127X_FOM_SEQCFG2, seq2); /* Unlock SPI */ sx127x_unlock(dev->spi); return ret; } /**************************************************************************** * Name: sx127x_fskook_syncword_get ****************************************************************************/ static void sx127x_fskook_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); wlerr("sx127x_fskook_syncword_get not implemented yet\n"); } /**************************************************************************** * Name: sx127x_fskook_syncword_set * * Description: * Set SyncWord for FSK/OOK * ****************************************************************************/ static int sx127x_fskook_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); uint8_t setbits = 0; uint8_t clrbits = 0; uint8_t offset = 0; int ret = OK; int i = 0; if (len > SX127X_FOM_SYNCSIZE_MAX) { wlerr("Unsupported sync word length %d!", len); ret = -EINVAL; goto errout; } /* Lock SPI */ sx127x_lock(dev->spi); if (len == 0) { /* Disable sync word generation and detection */ clrbits = (SX127X_FOM_SYNCCFG_SYNCSIZE_MASK | SX127X_FOM_SYNCCFG_SYNCON); setbits = 0; sx127x_modregbyte(dev, SX127X_FOM_SYNCCFG, setbits, clrbits); } else { /* Configure sync word length */ clrbits = SX127X_FOM_SYNCCFG_SYNCSIZE_MASK; setbits = (SX127X_FOM_SYNCCFG_SYNCON | SX127X_FOM_SYNCCFG_SYNCSIZE(len - 1)); sx127x_modregbyte(dev, SX127X_FOM_SYNCCFG, setbits, clrbits); /* Write sync words */ for (i = 0; i < len; i += 1) { offset = SX127X_FOM_SYNCVAL1 + i; sx127x_writeregbyte(dev, offset, sw[i]); } } /* Unlock SPI */ sx127x_unlock(dev->spi); errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_init * * Description: * Initialization specific for FSK/OOK modulation * ****************************************************************************/ static void sx127x_fskook_init(FAR struct sx127x_dev_s *dev) { uint8_t setbits = 0; uint8_t clrbits = 0; uint8_t syncword[] = { 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01 }; DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); /* Set FDEV */ sx127x_fskook_fdev_set(dev, SX127X_FDEV_DEFAULT); /* Set bitrate */ sx127x_fskook_bitrate_set(dev, SX127X_FOM_BITRATE_DEFAULT); /* Configure sequencer * WARNING: sequencer is OFF for now! */ sx127x_fskook_seq_init(dev); sx127x_fskook_seq_start(dev, false); /* Configure Sync Word * REVISIT: FSK communication doesn't work if syncword is disabled! */ sx127x_fskook_syncword_set(dev, syncword, 8); /* Configure bandwidth */ sx127x_fskook_rxbw_set(dev, SX127X_FSKOOK_RXBW_DEFAULT); sx127x_fskook_afcbw_set(dev, SX127X_FSKOOK_AFCBW_DEFAULT); /* Lock SPI */ sx127x_lock(dev->spi); /* Configure packet mode settings 1: * - fixlen * - RX/TX CRC */ setbits = 0; setbits |= dev->fskook.fixlen == true ? 0 : SX127X_FOM_PKTCFG1_PCKFORMAT; setbits |= dev->crcon == true ? SX127X_FOM_PKTCFG1_CRCON : 0; clrbits = SX127X_FOM_PKTCFG1_PCKFORMAT | SX127X_FOM_PKTCFG1_CRCON; /* Write packet mode settings 1 */ sx127x_modregbyte(dev, SX127X_FOM_PKTCFG1, setbits, clrbits); /* Configure packet mode settings 2: * - packet mode on */ setbits = 0; setbits |= SX127X_FOM_PKTCFG2_DATAMODE; clrbits = 0; /* Write packet mode settings 2 */ sx127x_modregbyte(dev, SX127X_FOM_PKTCFG2, setbits, clrbits); /* Configure PARAMP register */ setbits = (SX127X_FSKOOK_SHAPING_DEFAULT | SX127X_FSKOOK_PARAMP_DEFAULT); clrbits = (SX127X_CMN_PARAMP_PARAMP_MASK | SX127X_CMN_PARAMP_SHAPING_MASK); /* Write PARAMP register */ sx127x_modregbyte(dev, SX127X_CMN_PARAMP, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); } /**************************************************************************** * Name: sx127x_fskook_rssi_get * * Description: * Get current RSSI for FSK/OOK modem * ****************************************************************************/ static int16_t sx127x_fskook_rssi_get(FAR struct sx127x_dev_s *dev) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get register value */ regval = sx127x_readregbyte(dev, SX127X_FOM_RSSIVAL); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Return decoded RSSI value */ return SX127X_FOM_RSSIVAL_GET(regval); } /**************************************************************************** * Name: sx127x_fskook_fdev_set * * Description: * Set frequency deviation * ****************************************************************************/ static int sx127x_fskook_fdev_set(FAR struct sx127x_dev_s *dev, uint32_t freq) { uint32_t fdev = 0; int ret = OK; /* Only for FSK modulation */ if (dev->modulation != SX127X_MODULATION_FSK) { ret = -EINVAL; goto errout; } if (freq == dev->fskook.fdev) { goto errout; } /* Lock SPI */ sx127x_lock(dev->spi); /* Get FDEV value */ fdev = SX127X_FDEV_FROM_FREQ(freq); /* Write FDEV MSB */ sx127x_writeregbyte(dev, SX127X_FOM_FDEVMSB, SX127X_FOM_FDEV_MSB(fdev)); /* Write FDEV LSB */ sx127x_writeregbyte(dev, SX127X_FOM_FDEVLSB, SX127X_FOM_FDEV_LSB(fdev)); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Update local variable */ dev->fskook.fdev = freq; errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_bitrate_set * * Description: * Set bitrate for FSK/OOK modulation * ****************************************************************************/ static int sx127x_fskook_bitrate_set(FAR struct sx127x_dev_s *dev, uint32_t bitrate) { uint32_t br = 0; int ret = OK; if (bitrate == dev->fskook.bitrate) { goto errout; } /* Get bitrate register value */ br = SX127X_FXOSC / bitrate; /* Lock SPI */ sx127x_lock(dev->spi); /* Set fractial part to 0 */ sx127x_writeregbyte(dev, SX127X_FOM_BITRATEFRAC, 0); /* Write MSB */ sx127x_writeregbyte(dev, SX127X_FOM_BITRATEMSB, SX127X_FOM_BITRATE_MSB(br)); /* Write LSB */ sx127x_writeregbyte(dev, SX127X_FOM_BITRATELSB, SX127X_FOM_BITRATE_LSB(br)); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Update local variable */ dev->fskook.bitrate = bitrate; errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_preamble_set * * Description: * Set preamble for FSK/OOK modulation * ****************************************************************************/ static void sx127x_fskook_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); if (len == 0) { /* Disable detector */ regval = 0; sx127x_writeregbyte(dev, SX127X_FOM_PREDET, regval); } else { /* Configure preamble length */ regval = SX127X_FOM_PRE_MSB(len); sx127x_writeregbyte(dev, SX127X_FOM_PREMSB, regval); regval = SX127X_FOM_PRE_LSB(len); sx127x_writeregbyte(dev, SX127X_FOM_PRELSB, regval); /* Configure preamble polarity to 0xAA */ regval = SX127X_FOM_SYNCCFG_PREPOL; sx127x_modregbyte(dev, SX127X_FOM_SYNCCFG, regval, 0); /* Configure and enable preamble detector: * - tolerance = 10 * - detector size = 2B */ regval = (SX127X_FOM_PREDET_ON | SX127X_FOM_PREDET_SIZE_2B | SX127X_FOM_PREDET_TOL(10)); sx127x_writeregbyte(dev, SX127X_FOM_PREDET, regval); } /* Unlock SPI */ sx127x_unlock(dev->spi); } /**************************************************************************** * Name: sx127x_fskook_preamble_get * * Description: * Get current preamble configuration for FSK/OOK * ****************************************************************************/ static int sx127x_fskook_preamble_get(FAR struct sx127x_dev_s *dev) { wlerr("sx127x_fskook_preamble_get\n"); return 0; } #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ #ifdef CONFIG_LPWAN_SX127X_LORA /**************************************************************************** * Name: sx127x_lora_opmode_init * * Description: * Initialize operation mode for LORA * ****************************************************************************/ static int sx127x_lora_opmode_init(FAR struct sx127x_dev_s *dev, uint8_t opmode) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t dio0map = 0; uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; sx127x_lock(dev->spi); /* Get mode specific configuration */ switch (opmode) { case SX127X_OPMODE_SLEEP: case SX127X_OPMODE_STANDBY: case SX127X_OPMODE_FSRX: case SX127X_OPMODE_FSTX: { break; } case SX127X_OPMODE_TX: { /* DIO0 is TX DONE */ dio0map = SX127X_LRM_DIOMAP1_DIO0_TXDONE; /* Full buffer for TX */ sx127x_writeregbyte(dev, SX127X_LRM_TXBASE, 0); /* Reset FIFO pointer */ sx127x_writeregbyte(dev, SX127X_LRM_ADDRPTR, 0); break; } case SX127X_OPMODE_RX: case SX127X_OPMODE_RXSINGLE: { /* DIO0 is RX DONE */ dio0map = SX127X_LRM_DIOMAP1_DIO0_RXDONE; /* Full buffer for RX */ sx127x_writeregbyte(dev, SX127X_LRM_RXBASE, 0); /* Reset FIFO pointer */ sx127x_writeregbyte(dev, SX127X_LRM_ADDRPTR, 0); break; } case SX127X_OPMODE_CAD: { /* DIO0 is CAD DONE */ dio0map = SX127X_LRM_DIOMAP1_DIO0_CADDONE; break; } default: { wlerr("ERROR: invalid mode %d\n", opmode); ret = -EINVAL; goto errout; } } /* Configure DIO0 pin */ setbits = dio0map; clrbits = SX127X_CMN_DIOMAP1_DIO0_MASK; sx127x_modregbyte(dev, SX127X_CMN_DIOMAP1, setbits, clrbits); sx127x_unlock(dev->spi); errout: return ret; } /**************************************************************************** * Name: sx127x_lora_opmode_set * * Description: * Set operation mode for LORA * ****************************************************************************/ static int sx127x_lora_opmode_set(FAR struct sx127x_dev_s *dev, uint8_t opmode) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); int ret = OK; sx127x_lock(dev->spi); switch (opmode) { case SX127X_OPMODE_SLEEP: case SX127X_OPMODE_STANDBY: case SX127X_OPMODE_FSRX: case SX127X_OPMODE_FSTX: case SX127X_OPMODE_TX: case SX127X_OPMODE_RX: case SX127X_OPMODE_RXSINGLE: case SX127X_OPMODE_CAD: { /* Do nothing */ break; } default: { wlerr("ERROR: invalid LORA mode %d\n", opmode); ret = -EINVAL; goto errout; } } /* Update mode */ sx127x_modregbyte(dev, SX127X_CMN_OPMODE, ((opmode - 1) << SX127X_CMN_OPMODE_MODE_SHIFT), SX127X_CMN_OPMODE_MODE_MASK); sx127x_unlock(dev->spi); /* Wait for mode ready. REVISIT: do we need this ? */ nxsig_usleep(250); errout: return ret; } /**************************************************************************** * Name: sx127x_lora_syncword_get ****************************************************************************/ static void sx127x_lora_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_FSK || dev->modulation == SX127X_MODULATION_OOK); wlerr("sx127x_lora_syncword_get not implemented yet\n"); } /**************************************************************************** * Name: sx127x_lora_syncword_set * * Description: * Set SyncWord for LORA * ****************************************************************************/ static int sx127x_lora_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); int ret = OK; if (len != 1) { wlerr("LORA support sync word with len = 1 but len = %d\n", len); ret = -EINVAL; goto errout; } /* Lock SPI */ sx127x_lock(dev->spi); /* Write sync word */ sx127x_writeregbyte(dev, SX127X_LRM_SYNCWORD, sw[0]); /* Unlock SPI */ sx127x_unlock(dev->spi); errout: return ret; } /**************************************************************************** * Name: sx127x_lora_bw_set * * Description: * Configure LORA bandwidth * ****************************************************************************/ static int sx127x_lora_bw_set(FAR struct sx127x_dev_s *dev, uint8_t bw) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t clrbits = 0; uint8_t setbits = 0; int ret = OK; if (bw == dev->lora.bw) { goto errout; } switch (bw) { case LORA_BANDWIDTH_7P8KHZ: case LORA_BANDWIDTH_10P4KHZ: case LORA_BANDWIDTH_15P6KHZ: case LORA_BANDWIDTH_20P8KHZ: case LORA_BANDWIDTH_31P2KHZ: case LORA_BANDWIDTH_41P4KHZ: case LORA_BANDWIDTH_62P5KHZ: case LORA_BANDWIDTH_125KHZ: case LORA_BANDWIDTH_250KHZ: { /* Lock SPI */ sx127x_lock(dev->spi); setbits = bw << SX127X_LRM_MDMCFG1_BW_SHIFT; clrbits = SX127X_LRM_MDMCFG1_BW_MASK; sx127x_modregbyte(dev, SX127X_LRM_MDMCFG1, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); break; } default: { ret = -EINVAL; wlerr("Unsupported bandwidth %d\n", bw); goto errout; } } dev->lora.bw = bw; errout: return ret; } /**************************************************************************** * Name: sx127x_lora_cr_set * * Description: * Configure LORA coding rate * ****************************************************************************/ static int sx127x_lora_cr_set(FAR struct sx127x_dev_s *dev, uint8_t cr) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t clrbits = 0; uint8_t setbits = 0; int ret = OK; if (cr == dev->lora.cr) { goto errout; } switch (cr) { case LORA_CR_4d5: case LORA_CR_4d6: case LORA_CR_4d7: case LORA_CR_4d8: { /* Lock SPI */ sx127x_lock(dev->spi); setbits = cr << SX127X_LRM_MDMCFG1_CDRATE_SHIFT; clrbits = SX127X_LRM_MDMCFG1_CDRATE_MASK; sx127x_modregbyte(dev, SX127X_LRM_MDMCFG1, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); break; } default: { ret = -EINVAL; wlerr("Unsupported code rate %d\n", cr); goto errout; } } dev->lora.cr = cr; errout: return ret; } /**************************************************************************** * Name: sx127x_lora_sf_set * * Description: * Configure LORA SF * ****************************************************************************/ static int sx127x_lora_sf_set(FAR struct sx127x_dev_s *dev, uint8_t sf) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t dopt = SX127X_LRM_DETECTOPT_DO_SF7SF12; uint8_t dthr = SX127X_LRM_DETECTTHR_SF7SF12; uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; if (dev->lora.sf == sf) { goto errout; } /* Special configuration required by SF6 (highest data rate transmission): * - implicit header mode ON * - Detection optimize for SF6 * - Detection threshold for SF6 */ if (dev->lora.sf == 6) { if (dev->lora.implicthdr == true) { wlerr("SF6 needs implicit header ON!\n"); ret = -EINVAL; goto errout; } dopt = SX127X_LRM_DETECTOPT_DO_SF6; dthr = SX127X_LRM_DETECTTHR_SF6; } /* Lock SPI */ sx127x_lock(dev->spi); /* Write spreading factor */ clrbits = SX127X_LRM_MDMCFG2_SPRFACT_MASK; setbits = (sf << SX127X_LRM_MDMCFG2_SPRFACT_SHIFT); sx127x_modregbyte(dev, SX127X_LRM_MDMCFG2, setbits, clrbits); sx127x_writeregbyte(dev, SX127X_LRM_DETECTOPT, dopt); sx127x_writeregbyte(dev, SX127X_LRM_DETECTTHR, dthr); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Update local variable */ dev->lora.sf = sf; errout: return ret; } /**************************************************************************** * Name: sx127x_lora_implicthdr_set * * Description: * Enable/disable implicit header for LORA * ****************************************************************************/ static int sx127x_lora_implicthdr_set(FAR struct sx127x_dev_s *dev, bool enable) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; if (dev->lora.sf == 6 && enable == false) { wlerr("SF=6 requires implicit header ON\n"); ret = -EINVAL; goto errout; } if (enable == dev->lora.implicthdr) { goto errout; } /* Lock SPI */ sx127x_lock(dev->spi); /* Modify MDMCFG1 register */ clrbits = 0; setbits = SX127X_LRM_MDMCFG1_IMPLHDRON; sx127x_modregbyte(dev, SX127X_LRM_MDMCFG1, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Update local variable */ dev->lora.implicthdr = enable; errout: return ret; } /**************************************************************************** * Name: sx127x_lora_init * * Description: * Initialization specific for LORA modulation * ****************************************************************************/ static void sx127x_lora_init(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev->modulation == SX127X_MODULATION_LORA); uint8_t setbits = 0; uint8_t clrbits = 0; /* Configure sync word for LORA modulation */ setbits = SX127X_LRM_SYNCWORD_DEFAULT; sx127x_lora_syncword_set(dev, &setbits, 1); /* Configure bandwidth */ sx127x_lora_bw_set(dev, SX127X_LRM_BW_DEFAULT); /* Configure coding rate */ sx127x_lora_cr_set(dev, SX127X_LRM_CR_DEFAULT); /* TODO: Configure frequency hopping */ /* sx127x_lora_fhop_set(dev,) */ /* Configure spreading factor */ sx127x_lora_sf_set(dev, SX127X_LRM_SF_DEFAULT); /* Configure LORA header */ sx127x_lora_implicthdr_set(dev, CONFIG_LPWAN_SX127X_LORA_IMPHEADER); /* Lock SPI */ sx127x_lock(dev->spi); /* Configure maximum payload */ sx127x_writeregbyte(dev, SX127X_LRM_PAYLOADMAX, SX127X_LRM_PAYLOADMAX_DEFAULT); /* Modem PHY config 2: * - RXCRCON * NOTE: this works differently for implicit header and explicit header * - packet mode */ setbits = (dev->crcon == true ? SX127X_LRM_MDMCFG2_RXCRCON : 0); clrbits = (SX127X_LRM_MDMCFG2_TXCONT | SX127X_LRM_MDMCFG2_RXCRCON); sx127x_modregbyte(dev, SX127X_LRM_MDMCFG2, setbits, clrbits); /* Invert I and Q signals if configured */ setbits = (dev->lora.invert_iq == true ? SX127X_LRM_INVERTIQ_IIQ : 0); clrbits = SX127X_LRM_INVERTIQ_IIQ; sx127x_modregbyte(dev, SX127X_LRM_INVERTIQ, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); } /**************************************************************************** * Name: sx127x_lora_rssi_correct * * Description: * Correct RSSI for LORA radio according to datasheet * ****************************************************************************/ static int16_t sx127x_lora_rssi_correct(FAR struct sx127x_dev_s *dev, uint32_t freq, int8_t snr, uint8_t regval) { int16_t offset = 0; int16_t ret = 0; /* Ignore SNR if >= 0 */ if (snr >= 0) { snr = 0; } /* RSSI offset depends on RF frequency */ offset = (freq > SX127X_HFBAND_THR ? SX127X_LRM_RSSIVAL_HF_OFFSET : SX127X_LRM_RSSIVAL_LF_OFFSET); /* Get corrected RSSI value */ ret = regval + offset + snr; return ret; } /**************************************************************************** * Name: sx127x_lora_snr_get * * Description: * Get estimation of SNR on last packet received for LORA modem * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT static int8_t sx127x_lora_snr_get(FAR struct sx127x_dev_s *dev) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get register value */ regval = sx127x_readregbyte(dev, SX127X_LRM_PKTSNR); /* Get SNR */ regval = regval / 4; /* Unlock SPI */ sx127x_unlock(dev->spi); /* Return corrected RSSI */ return (int8_t)regval; } /**************************************************************************** * Name: sx127x_lora_pckrssi_get * * Description: * Get RSSI of the last received LORA packet * ****************************************************************************/ static int16_t sx127x_lora_pckrssi_get(FAR struct sx127x_dev_s *dev, int8_t snr) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get register value */ regval = sx127x_readregbyte(dev, SX127X_LRM_PKTRSSI); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Return corrected RSSI */ return sx127x_lora_rssi_correct(dev, dev->freq, snr, regval); } #endif /**************************************************************************** * Name: sx127x_lora_rssi_get * * Description: * Get current RSSI for LORA modem * ****************************************************************************/ static int16_t sx127x_lora_rssi_get(FAR struct sx127x_dev_s *dev) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get register value */ regval = sx127x_readregbyte(dev, SX127X_LRM_RSSIVAL); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Return corrected RSSI */ return sx127x_lora_rssi_correct(dev, dev->freq, 0, regval); } /**************************************************************************** * Name: sx127x_lora_preamble_set * * Description: * Set preamble for LORA modulation * ****************************************************************************/ static void sx127x_lora_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Configure preamble len */ regval = SX127X_LRM_PRE_MSB(len); sx127x_writeregbyte(dev, SX127X_LRM_PREMSB, regval); regval = SX127X_LRM_PRE_LSB(len); sx127x_writeregbyte(dev, SX127X_LRM_PRELSB, regval); /* Unlock SPI */ sx127x_unlock(dev->spi); } /**************************************************************************** * Name: sx127x_lora_preamble_get * * Description: * ****************************************************************************/ static int sx127x_lora_preamble_get(FAR struct sx127x_dev_s *dev) { wlerr("sx127x_lora_preamble_get\n"); return 0; } #endif /* CONFIG_LPWAN_SX127X_LORA */ /**************************************************************************** * Name: sx127x_syncword_get ****************************************************************************/ static void sx127x_syncword_get(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, FAR uint8_t *len) { dev->ops.syncword_get(dev, sw, len); } /**************************************************************************** * Name: sx127x_syncword_set ****************************************************************************/ static int sx127x_syncword_set(FAR struct sx127x_dev_s *dev, FAR uint8_t *sw, uint8_t len) { return dev->ops.syncword_set(dev, sw, len); } /**************************************************************************** * Name: sx127x_modulation_get * * Description: * Get current radio modulation * ****************************************************************************/ static uint8_t sx127x_modulation_get(FAR struct sx127x_dev_s *dev) { uint8_t regval = 0; uint8_t ret = 0; /* Get OPMODE register */ regval = sx127x_readregbyte(dev, SX127X_CMN_OPMODE); if (regval & SX127X_CMN_OPMODE_LRMODE) { /* LORA modulation */ ret = SX127X_MODULATION_LORA; } else { /* FSK or OOK modulation */ ret = (regval & SX127X_CMN_OPMODE_MODTYPE_FSK ? SX127X_MODULATION_FSK : SX127X_MODULATION_OOK); } return ret; } /**************************************************************************** * Name: sx127x_ops_set ****************************************************************************/ static void sx127x_ops_set(FAR struct sx127x_dev_s *dev, uint8_t modulation) { if (modulation <= SX127X_MODULATION_OOK) { /* NOTE: we need opmode_init and opmode_set for FSK/OOK even if * support for these modulations is disabled! */ dev->ops.opmode_init = sx127x_fskook_opmode_init; dev->ops.opmode_set = sx127x_fskook_opmode_set; #ifdef CONFIG_LPWAN_SX127X_FSKOOK dev->ops.init = sx127x_fskook_init; dev->ops.isr0_process = sx127x_fskook_isr0_process; dev->ops.preamble_set = sx127x_fskook_preamble_set; dev->ops.preamble_get = sx127x_fskook_preamble_get; dev->ops.rssi_get = sx127x_fskook_rssi_get; dev->ops.syncword_set = sx127x_fskook_syncword_set; dev->ops.syncword_get = sx127x_fskook_syncword_get; #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT dev->ops.send = sx127x_fskook_send; #endif #ifdef CONFIG_DEBUG_WIRELESS_INFO dev->ops.dumpregs = sx127x_fskook_dumpregs; #endif #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ } #ifdef CONFIG_LPWAN_SX127X_LORA if (modulation == SX127X_MODULATION_LORA) { dev->ops.init = sx127x_lora_init; dev->ops.isr0_process = sx127x_lora_isr0_process; dev->ops.opmode_init = sx127x_lora_opmode_init; dev->ops.opmode_set = sx127x_lora_opmode_set; dev->ops.preamble_set = sx127x_lora_preamble_set; dev->ops.preamble_get = sx127x_lora_preamble_get; dev->ops.rssi_get = sx127x_lora_rssi_get; dev->ops.syncword_set = sx127x_lora_syncword_set; dev->ops.syncword_get = sx127x_lora_syncword_get; #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT dev->ops.send = sx127x_lora_send; #endif #ifdef CONFIG_DEBUG_WIRELESS_INFO dev->ops.dumpregs = sx127x_lora_dumpregs; #endif } #endif /* CONFIG_LPWAN_SX127X_LORA */ } /**************************************************************************** * Name: sx127x_modulation_init ****************************************************************************/ static void sx127x_modulation_init(FAR struct sx127x_dev_s *dev) { dev->ops.init(dev); /* Configure preamble */ sx127x_preamble_set(dev, CONFIG_LPWAN_SX127X_PREAMBLE_DEFAULT); /* Dump registers after initial configuration */ sx127x_dumpregs(dev); } /**************************************************************************** * Name: sx127x_modulation_set * * Description: * Set radio modulation and configure * ****************************************************************************/ static int sx127x_modulation_set(FAR struct sx127x_dev_s *dev, uint8_t modulation) { uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; wlinfo("modulation_set %d->%d\n", dev->modulation, modulation); if (modulation == dev->modulation) { goto errout; } /* Modulation can be only changed in SLEEP mode */ sx127x_opmode_set(dev, SX127X_OPMODE_SLEEP); /* Change modulation */ switch (modulation) { #ifdef CONFIG_LPWAN_SX127X_FSKOOK case SX127X_MODULATION_FSK: { clrbits = (SX127X_CMN_OPMODE_LRMODE | SX127X_CMN_OPMODE_MODTYPE_MASK); setbits = SX127X_CMN_OPMODE_MODTYPE_FSK; break; } case SX127X_MODULATION_OOK: { clrbits = (SX127X_CMN_OPMODE_LRMODE | SX127X_CMN_OPMODE_MODTYPE_MASK); setbits = SX127X_CMN_OPMODE_MODTYPE_OOK; break; } #endif /* CONFIG_LPWAN_SX127X_FSKOOK */ #ifdef CONFIG_LPWAN_SX127X_LORA case SX127X_MODULATION_LORA: { clrbits = SX127X_CMN_OPMODE_MODTYPE_MASK; setbits = SX127X_CMN_OPMODE_LRMODE; break; } #endif /* CONFIG_LPWAN_SX127X_LORA */ default: { wlerr("ERROR: Unsupported modulation type %d\n", modulation); ret = -EINVAL; goto errout; } } /* Lock SPI */ sx127x_lock(dev->spi); /* Modify register */ sx127x_modregbyte(dev, SX127X_CMN_OPMODE, setbits, clrbits); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Initialization specific for modulation and initialize private ops */ sx127x_ops_set(dev, modulation); /* Update local variable */ dev->modulation = modulation; /* Initial configuration */ sx127x_modulation_init(dev); errout: return ret; } /**************************************************************************** * Name: sx127x_fskook_rssi_get ****************************************************************************/ static int16_t sx127x_rssi_get(FAR struct sx127x_dev_s *dev) { return dev->ops.rssi_get(dev); } /**************************************************************************** * Name: sx127x_channel_scan * * Description: * ****************************************************************************/ static bool sx127x_channel_scan(FAR struct sx127x_dev_s *dev, FAR struct sx127x_chanscan_ioc_s *chanscan) { struct timespec tstart; struct timespec tnow; bool ret = true; int16_t rssi = 0; int16_t max = 0; int16_t min = 0; /* Set frequency */ sx127x_frequency_set(dev, chanscan->freq); /* Set mode to RX */ sx127x_opmode_set(dev, SX127X_OPMODE_RX); /* Get start time */ clock_gettime(CLOCK_REALTIME, &tstart); /* Initialize min/max */ max = INT16_MIN; min = INT16_MAX; do { /* Get time now */ clock_gettime(CLOCK_REALTIME, &tnow); /* Check RSSI */ rssi = dev->ops.rssi_get(dev); /* Store maximum/minimum value */ if (rssi > max) { max = rssi; } else if (rssi < min) { min = rssi; } if (rssi > chanscan->rssi_thr) { ret = false; break; } /* Wait some time */ nxsig_usleep(1000); } while (tstart.tv_sec + chanscan->stime > tnow.tv_sec); /* Set mode to STANDBY */ sx127x_opmode_set(dev, SX127X_OPMODE_STANDBY); /* Store limit values */ chanscan->rssi_max = max; chanscan->rssi_min = min; /* Store return value in struct */ chanscan->free = ret; return ret; } /**************************************************************************** * Name: sx127x_random_get * * Description: * ****************************************************************************/ static uint32_t sx127x_random_get(FAR struct sx127x_dev_s *dev) { wlerr("sx127x_random_get not implemented yet\n"); return 0; } /**************************************************************************** * Name: sx127x_frequency_get * * Description: * Get RF carrier frequency * ****************************************************************************/ static uint32_t sx127x_frequency_get(FAR struct sx127x_dev_s *dev) { wlerr("sx127x_frequency_get\n"); return 0; } /**************************************************************************** * Name: sx127x_frequency_set * * Description: * Set RF carrier frequency for LORA and FSK/OOK modulation * ****************************************************************************/ static int sx127x_frequency_set(FAR struct sx127x_dev_s *dev, uint32_t freq) { uint32_t frf = 0; int ret = OK; wlinfo("frequency %" PRId32 "->%" PRId32 "\n", dev->freq, freq); if (freq == dev->freq) { goto errout; } /* REVISIT: needs sleep/standby mode ? */ /* Lock SPI */ sx127x_lock(dev->spi); /* Get FRF value */ frf = SX127X_FRF_FROM_FREQ(freq); /* Write FRF MSB */ sx127x_writeregbyte(dev, SX127X_CMN_FRFMSB, SX127X_CMN_FRF_MSB(frf)); /* Write FRF MID */ sx127x_writeregbyte(dev, SX127X_CMN_FRFMID, SX127X_CMN_FRF_MID(frf)); /* Write FRF LSB */ sx127x_writeregbyte(dev, SX127X_CMN_FRFLSB, SX127X_CMN_FRF_LSB(frf)); /* Unlock SPI */ sx127x_unlock(dev->spi); /* Update local variable */ dev->freq = freq; /* Call board-specific LF/HF configuration */ ret = dev->lower->freq_select(freq); if (ret < 0) { wlerr("Board-specific freq_select failed %d!\n", ret); goto errout; } errout: return ret; } /**************************************************************************** * Name: sx127x_power_set ****************************************************************************/ static int sx127x_power_set(FAR struct sx127x_dev_s *dev, int8_t power) { #ifndef CONFIG_LPWAN_SX127X_TXSUPPORT return -ENOSYS; #else bool pa_select = false; bool pa_dac = false; uint8_t setbits = 0; uint8_t clrbits = 0; int ret = OK; if (dev->power == power) { goto errout; } /* PA BOOST configuration */ if (power > SX127X_PASELECT_POWER || dev->pa_force == true) { pa_select = true; } /* High power PA BOOST */ if (power >= 20) { pa_dac = true; } /* Saturate power output */ if (pa_select == true) { if (pa_dac == true) { if (power < 5) { power = 5; } else if (power > 20) { power = 20; } } else { if (power < 2) { power = 2; } else if (power > 17) { power = 17; } } } else { if (power < -1) { power = -1; } else if (power > 14) { power = 14; } } wlinfo("power %d->%d, pa=%d, dac=%d\n", dev->power, power, pa_select, pa_dac); sx127x_lock(dev->spi); if (pa_select == true) { if (pa_dac == true) { /* Enable high power on PA_BOOST */ sx127x_writeregbyte(dev, SX127X_CMN_PADAC, SX127X_CMN_PADAC_BOOST); /* Configure output power */ setbits = (power - 5) << SX127X_CMN_PACFG_OUTPOWER_SHIFT; clrbits = SX127X_CMN_PACFG_OUTPOWER_MASK; sx127x_modregbyte(dev, SX127X_CMN_PACFG, setbits, clrbits); } else { /* Disable high power on PA_BOOST */ sx127x_writeregbyte(dev, SX127X_CMN_PADAC, SX127X_CMN_PADAC_DEFAULT); /* Configure output power */ setbits = (power - 2) << SX127X_CMN_PACFG_OUTPOWER_SHIFT; clrbits = SX127X_CMN_PACFG_OUTPOWER_MASK; sx127x_modregbyte(dev, SX127X_CMN_PACFG, setbits, clrbits); } /* Enable PA BOOST output */ sx127x_modregbyte(dev, SX127X_CMN_PACFG, SX127X_CMN_PACFG_PASELECT, 0); } else { /* Configure output power and max power to 13.8 dBm */ setbits = ((power + 1) << SX127X_CMN_PACFG_OUTPOWER_SHIFT); setbits |= (5 << SX127X_CMN_PACFG_MAXPOWER_SHIFT); clrbits = (SX127X_CMN_PACFG_OUTPOWER_MASK | SX127X_CMN_PACFG_MAXPOWER_SHIFT); sx127x_modregbyte(dev, SX127X_CMN_PACFG, setbits, clrbits); /* Enable RFO output */ sx127x_modregbyte(dev, SX127X_CMN_PACFG, 0, SX127X_CMN_PACFG_PASELECT); } sx127x_unlock(dev->spi); /* Call board-specific logic */ ret = dev->lower->pa_select(pa_select); if (ret < 0) { wlerr("Board-specific pa_select failed %d!\n", ret); } /* Update local variable */ dev->power = power; errout: return ret; #endif } /**************************************************************************** * Name: sx127x_power_get ****************************************************************************/ static int8_t sx127x_power_get(FAR struct sx127x_dev_s *dev) { #ifndef CONFIG_LPWAN_SX127X_TXSUPPORT return 0; #else return dev->power; #endif } /**************************************************************************** * Name: sx127x_preamble_set ****************************************************************************/ static void sx127x_preamble_set(FAR struct sx127x_dev_s *dev, uint32_t len) { dev->ops.preamble_set(dev, len); } /**************************************************************************** * Name: sx127x_preamble_get ****************************************************************************/ static int sx127x_preamble_get(FAR struct sx127x_dev_s *dev) { return dev->ops.preamble_get(dev); } /**************************************************************************** * Name: sx127x_version_get * * Description: * Get chip version * ****************************************************************************/ static uint8_t sx127x_version_get(FAR struct sx127x_dev_s *dev) { uint8_t regval = 0; /* Lock SPI */ sx127x_lock(dev->spi); /* Get version */ regval = sx127x_readregbyte(dev, SX127X_CMN_VERSION); /* Unlock SPI */ sx127x_unlock(dev->spi); return regval; } /**************************************************************************** * Name: sx127x_calibration * * Description: * Calibrate radio for given frequency * ****************************************************************************/ static int sx127x_calibration(FAR struct sx127x_dev_s *dev, uint32_t freq) { uint8_t regval = 0; int ret = OK; /* NOTE: The automatic calibration at POR and Reset is only valid at * 434 MHz. */ wlinfo("SX127X calibration for %" PRId32 "\n", freq); /* Calibration is supported only in FSK/OOK mode */ ret = sx127x_modulation_set(dev, SX127X_MODULATION_FSK); if (ret < 0) { wlerr("ERROR: can't change modulation to FSK \n"); goto errout; } /* We need standby mode ? */ ret = sx127x_opmode_set(dev, SX127X_OPMODE_STANDBY); /* Set calibration frequency */ sx127x_frequency_set(dev, freq); /* Lock SPI */ sx127x_lock(dev->spi); /* Start calibration */ sx127x_modregbyte(dev, SX127X_FOM_IMAGECAL, SX127X_FOM_IMAGECAL_IMGCALSTART, 0); /* Wait for calibration done */ do { /* Wait 10ms */ nxsig_usleep(10000); /* Get register */ regval = sx127x_readregbyte(dev, SX127X_FOM_IMAGECAL); } while (regval & SX127X_FOM_IMAGECAL_IMGCALRUN); /* Unlock SPI */ sx127x_unlock(dev->spi); wlinfo("Calibration done\n"); errout: return ret; } /**************************************************************************** * Name: sx127x_init * * Description: * Initialize SX127X chip * ****************************************************************************/ static int sx127x_init(FAR struct sx127x_dev_s *dev) { int ret = OK; uint8_t regval = 0; wlinfo("Init sx127x dev\n"); /* Reset radio */ sx127x_reset(dev); /* Get initial modem state */ regval = sx127x_readregbyte(dev, SX127X_CMN_OPMODE); dev->opmode = (((regval >> SX127X_CMN_OPMODE_MODE_SHIFT) & SX127X_CMN_OPMODE_MODE_MASK) + 1); /* After reset - FSK mode */ dev->modulation = SX127X_MODULATION_FSK; /* Initialize modem ops */ sx127x_ops_set(dev, dev->modulation); wlinfo("Init state: modulation=%d, opmode=%d\n", dev->modulation, dev->opmode); #ifdef CONFIG_LPWAN_SX127X_FSKOOK /* Initialize FSK/OOK modem only if support is enabled */ sx127x_modulation_init(dev); #endif /* Get chip version */ regval = sx127x_version_get(dev); if (regval == 0x00) { /* Probably sth wrong with communication */ wlerr("ERROR: failed to get chip version!\n"); ret = -ENODATA; goto errout; } wlinfo("SX127X version = 0x%02x\n", regval); /* Calibration */ ret = sx127x_calibration(dev, SX127X_FREQ_CALIBRATION); if (ret < 0) { wlerr("ERROR: calibration failed \n"); } /* Set default modulation */ sx127x_modulation_set(dev, CONFIG_LPWAN_SX127X_MODULATION_DEFAULT); /* Enter SLEEP mode */ sx127x_opmode_set(dev, SX127X_OPMODE_SLEEP); /* Set default channel frequency - common for FSK/OOK and LORA */ ret = sx127x_frequency_set(dev, CONFIG_LPWAN_SX127X_RFFREQ_DEFAULT); if (ret < 0) { goto errout; } /* Configure RF output power - common for FSK/OOK and LORA */ ret = sx127x_power_set(dev, CONFIG_LPWAN_SX127X_TXPOWER_DEFAULT); if (ret < 0) { goto errout; } wlinfo("Init sx127x dev - DONE\n"); errout: return ret; } /**************************************************************************** * Name: sx127x_deinit * * Description: * Deinitialize SX127X chip * ****************************************************************************/ static int sx127x_deinit(FAR struct sx127x_dev_s *dev) { wlinfo("Deinit sx127x dev\n"); /* Enter SLEEP mode */ sx127x_opmode_set(dev, SX127X_OPMODE_SLEEP); /* Reset radio */ sx127x_reset(dev); return OK; } #ifdef CONFIG_DEBUG_WIRELESS_INFO /**************************************************************************** * Name: sx127x_lora_dumpregs * * Description: * Dump registers for LORA modem * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_LORA static void sx127x_lora_dumpregs(FAR struct sx127x_dev_s *dev) { sx127x_lock(dev->spi); wlinfo("LORA dump:\n"); wlinfo("FIFO: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FIFO)); wlinfo("OPMODE: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_OPMODE)); wlinfo("FRFMSB: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFMSB)); wlinfo("FRFMID: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFMID)); wlinfo("FRFLSB: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFLSB)); wlinfo("PACFG: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PACFG)); wlinfo("PARAMP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PARAMP)); wlinfo("OCP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_OCP)); wlinfo("LNA: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_LNA)); wlinfo("ADDRPTR: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_ADDRPTR)); wlinfo("TXBASE: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_TXBASE)); wlinfo("RXBASE: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXBASE)); wlinfo("RXCURR: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXCURR)); wlinfo("IRQMASK: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_IRQMASK)); wlinfo("IRQ: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_IRQ)); wlinfo("RXBYTES: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXBYTES)); wlinfo("RXHDRMSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXHDRMSB)); wlinfo("RXHDRLSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXHDRLSB)); wlinfo("RXPKTMSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXPKTMSB)); wlinfo("RXPKTLSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXPKTLSB)); wlinfo("MODSTAT: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_MODSTAT)); wlinfo("PKTSNR: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PKTSNR)); wlinfo("PKTRSSI: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PKTRSSI)); wlinfo("RSSI: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RSSIVAL)); wlinfo("HOPCHAN: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_HOPCHAN)); wlinfo("MDMCFG1: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_MDMCFG1)); wlinfo("MDMCFG2: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_MDMCFG2)); wlinfo("RXTIMEOUTLSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXTIMEOUTLSB)); wlinfo("PREMSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PREMSB)); wlinfo("PRELSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PRELSB)); wlinfo("PAYLOADLEN: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PAYLOADLEN)); wlinfo("PAYLOADMAX: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_PAYLOADMAX)); wlinfo("HOPPER: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_HOPPER)); wlinfo("RXFIFOADDR: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RXFIFOADDR)); wlinfo("MODEMCFG3: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_MODEMCFG3)); wlinfo("FEIMSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_FEIMSB)); wlinfo("FEIMID: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_FEIMID)); wlinfo("FEILSB: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_FEILSB)); wlinfo("RSSIWIDEBAND: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_RSSIWIDEBAND)); wlinfo("DETECTOPT: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_DETECTOPT)); wlinfo("INVERTIQ: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_INVERTIQ)); wlinfo("DETECTTHR: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_DETECTTHR)); wlinfo("SYNCWORD: %02x\n", sx127x_readregbyte(dev, SX127X_LRM_SYNCWORD)); wlinfo("DIOMAP1: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_DIOMAP1)); wlinfo("DIOMAP2: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_DIOMAP2)); wlinfo("VERSION: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_VERSION)); wlinfo("TCXO: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_TCXO)); wlinfo("PADAC: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PADAC)); wlinfo("FTEMP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FTEMP)); wlinfo("AGCREF: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCREF)); wlinfo("AGCTHR1: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR1)); wlinfo("AGCTHR2: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR2)); wlinfo("AGCTHR3: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR3)); wlinfo("PLL: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PLL)); sx127x_unlock(dev->spi); } #endif /* CONFIG_LPWAN_SX127X_LORA */ /**************************************************************************** * Name: sx127x_fskook_dumpregs * * Description: * Dump registers for FSK/OOK modem * ****************************************************************************/ #ifdef CONFIG_LPWAN_SX127X_FSKOOK static void sx127x_fskook_dumpregs(FAR struct sx127x_dev_s *dev) { sx127x_lock(dev->spi); wlinfo("FSK/OOK dump:\n"); wlinfo("FIFO: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FIFO)); wlinfo("OPMODE: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_OPMODE)); wlinfo("FRFMSB: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFMSB)); wlinfo("FRFMID: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFMID)); wlinfo("FRFLSB: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FRFLSB)); wlinfo("PACFG: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PACFG)); wlinfo("PARAMP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PARAMP)); wlinfo("OCP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_OCP)); wlinfo("LNA: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_LNA)); wlinfo("BITRATEMSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_BITRATEMSB)); wlinfo("BITRATELSM: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_BITRATELSB)); wlinfo("FDEVMSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_FDEVMSB)); wlinfo("FDEVLSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_FDEVLSB)); wlinfo("RXCFG: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXCFG)); wlinfo("RSSICFG: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RSSICFG)); wlinfo("RSSICOLL: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RSSICOLL)); wlinfo("RSSITHR: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RSSITHR)); wlinfo("RSSIVAL: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RSSIVAL)); wlinfo("RXBW: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXBW)); wlinfo("AFCBW: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_AFCBW)); wlinfo("OOKPEAK: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_OOKPEAK)); wlinfo("OOKFIX: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_OOKFIX)); wlinfo("AFCFEI: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_AFCFEI)); wlinfo("AFCMSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_AFCMSB)); wlinfo("AFCLSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_AFCLSB)); wlinfo("FEIMSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_FEIMSB)); wlinfo("FEILSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_FEILSB)); wlinfo("PREDET: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PREDET)); wlinfo("RXTIMEOUT1: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXTIMEOUT1)); wlinfo("RXTIMEOUT2: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXTIMEOUT1)); wlinfo("RXTIMEOUT3: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXTIMEOUT1)); wlinfo("RXDELAY: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_RXDELAY)); wlinfo("OSC: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_OSC)); wlinfo("PREMSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PREMSB)); wlinfo("PRELSB: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PRELSB)); wlinfo("SYNCCFG: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCCFG)); wlinfo("SYNCVAL1: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCVAL1)); wlinfo("SYNCVAL2: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCVAL2)); wlinfo("SYNCVAL3: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCVAL3)); wlinfo("SYNCVAL4: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCVAL4)); wlinfo("SYNCVAL5: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SYNCVAL5)); wlinfo("PKTCFG1: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PKTCFG1)); wlinfo("PKTCFG2: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PKTCFG2)); wlinfo("PAYLOADLEN: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PAYLOADLEN)); wlinfo("NODEADDR: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_NODEADDR)); wlinfo("BROADCAST: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_BROADCAST)); wlinfo("FIFOTHR: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_FIFOTHR)); wlinfo("SEQCFG1: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SEQCFG1)); wlinfo("SEQCFG2: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_SEQCFG2)); wlinfo("TIMRES: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_TIMRES)); wlinfo("TIMER1COEF: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_TIMER1COEF)); wlinfo("TIMER2COEF: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_TIMER2COEF)); wlinfo("IMAGECAL: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_IMAGECAL)); wlinfo("TEMP: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_TEMP)); wlinfo("LOWBAT: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_LOWBAT)); wlinfo("IRQ1: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_IRQ1)); wlinfo("IRQ2: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_IRQ2)); wlinfo("PLLHOP: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_PLLHOP)); wlinfo("BITRATEFRAC: %02x\n", sx127x_readregbyte(dev, SX127X_FOM_BITRATEFRAC)); wlinfo("DIOMAP1: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_DIOMAP1)); wlinfo("DIOMAP2: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_DIOMAP2)); wlinfo("VERSION: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_VERSION)); wlinfo("TCXO: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_TCXO)); wlinfo("PADAC: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PADAC)); wlinfo("FTEMP: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_FTEMP)); wlinfo("AGCREF: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCREF)); wlinfo("AGCTHR1: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR1)); wlinfo("AGCTHR2: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR2)); wlinfo("AGCTHR3: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_AGCTHR3)); wlinfo("PLL: %02x\n", sx127x_readregbyte(dev, SX127X_CMN_PLL)); sx127x_unlock(dev->spi); } #endif /**************************************************************************** * Name: sx127x_dumpregs * * Description: * Dump registers according to current modulation * ****************************************************************************/ static void sx127x_dumpregs(FAR struct sx127x_dev_s *dev) { switch (dev->modulation) { #ifdef CONFIG_LPWAN_SX127X_LORA case SX127X_MODULATION_LORA: { sx127x_lora_dumpregs(dev); break; } #endif #ifdef CONFIG_LPWAN_SX127X_FSKOOK case SX127X_MODULATION_FSK: case SX127X_MODULATION_OOK: { sx127x_fskook_dumpregs(dev); break; } #endif default: { wlinfo("Unknown SX127X modulation\n"); break; } } } #endif /* CONFIG_DEBUG_WIRELESS_INFO */ /**************************************************************************** * Name: sx127x_unregister * * Description: * Unregister SX127X device * ****************************************************************************/ static int sx127x_unregister(FAR struct sx127x_dev_s *dev) { DEBUGASSERT(dev != NULL); /* Release IRQ */ sx127x_attachirq0(dev, NULL, NULL); /* Destroy semaphores */ nxsem_destroy(&dev->dev_sem); #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT nxsem_destroy(&dev->tx_sem); #endif #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT nxsem_destroy(&dev->rx_sem); nxsem_destroy(&dev->rx_buffer_sem); #endif return OK; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: sx127x_register * * Description: * Register sx127x driver * ****************************************************************************/ int sx127x_register(FAR struct spi_dev_s *spi, FAR const struct sx127x_lower_s *lower) { FAR struct sx127x_dev_s *dev = NULL; int ret = OK; DEBUGASSERT(spi != NULL); DEBUGASSERT(lower != NULL); DEBUGASSERT(lower->reset != NULL); DEBUGASSERT(lower->irq0attach != NULL); DEBUGASSERT(lower->opmode_change != NULL); DEBUGASSERT(lower->freq_select != NULL); DEBUGASSERT(lower->pa_select != NULL); /* Only one sx127x device supported for now */ dev = &g_sx127x_devices[0]; /* Reset data */ memset(dev, 0, sizeof(struct sx127x_dev_s)); /* Attach the interface, lower driver */ dev->spi = spi; dev->lower = lower; /* Initlaize configuration */ dev->idle = SX127X_IDLE_OPMODE; #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT dev->pa_force = lower->pa_force; #endif dev->crcon = CONFIG_LPWAN_SX127X_CRCON; #ifdef CONFIG_LPWAN_SX127X_FSKOOK dev->fskook.fixlen = false; #endif #ifdef CONFIG_LPWAN_SX127X_LORA dev->lora.invert_iq = false; #endif /* Polled file decr */ dev->pfd = NULL; /* Initialize sem */ nxsem_init(&dev->dev_sem, 0, 1); #ifdef CONFIG_LPWAN_SX127X_TXSUPPORT nxsem_init(&dev->tx_sem, 0, 0); #endif #ifdef CONFIG_LPWAN_SX127X_RXSUPPORT nxsem_init(&dev->rx_sem, 0, 0); nxsem_init(&dev->rx_buffer_sem, 0, 1); #endif /* Attach irq0 - TXDONE/RXDONE/CADDONE */ sx127x_attachirq0(dev, sx127x_irq0handler, dev); /* TODO: support for irq1-5 */ wlinfo("Registering " SX127X_DEV_NAME "\n"); ret = register_driver(SX127X_DEV_NAME, &sx127x_fops, 0666, dev); if (ret < 0) { wlerr("ERROR: register_driver() failed: %d\n", ret); sx127x_unregister(dev); } return ret; }