/************************************************************************************ * configs/sama5d3-xplained/src/sam_usb.c * * Copyright (C) 2014-2016 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ /************************************************************************************ * Included Files ************************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include "up_arch.h" #include "sam_pio.h" #include "sam_usbhost.h" #include "chip/sam_ohci.h" #include "sama5d3-xplained.h" #if defined(CONFIG_SAMA5_UHPHS) || defined(CONFIG_SAMA5_UDPHS) /************************************************************************************ * Pre-processor Definitions ************************************************************************************/ #ifndef CONFIG_SAMA5D3XPLAINED_USBHOST_PRIO # define CONFIG_SAMA5D3XPLAINED_USBHOST_PRIO 50 #endif #ifndef CONFIG_SAMA5D3XPLAINED_USBHOST_STACKSIZE # define CONFIG_SAMA5D3XPLAINED_USBHOST_STACKSIZE 1024 #endif #ifdef HAVE_USBDEV # undef CONFIG_SAMA5_UHPHS_RHPORT1 #endif /************************************************************************************ * Private Data ************************************************************************************/ /* Retained device driver handles */ #ifdef CONFIG_SAMA5_OHCI static struct usbhost_connection_s *g_ohciconn; #endif #ifdef CONFIG_SAMA5_EHCI static struct usbhost_connection_s *g_ehciconn; #endif /* Overcurrent interrupt handler */ #if defined(HAVE_USBHOST) && defined(CONFIG_SAMA5_PIOD_IRQ) static xcpt_t g_ochandler; #endif /************************************************************************************ * Private Functions ************************************************************************************/ /************************************************************************************ * Name: usbhost_waiter * * Description: * Wait for USB devices to be connected to either the OHCI or EHCI hub. * ************************************************************************************/ #if HAVE_USBHOST #ifdef CONFIG_DEBUG_USB static int usbhost_waiter(struct usbhost_connection_s *dev, const char *hcistr) #else static int usbhost_waiter(struct usbhost_connection_s *dev) #endif { struct usbhost_hubport_s *hport; uinfo("Running\n"); for (;;) { /* Wait for the device to change state */ DEBUGVERIFY(CONN_WAIT(dev, &hport)); uinfo("%s\n", hport->connected ? "connected" : "disconnected"); /* Did we just become connected? */ if (hport->connected) { /* Yes.. enumerate the newly connected device */ (void)CONN_ENUMERATE(dev, hport); } } /* Keep the compiler from complaining */ return 0; } #endif /************************************************************************************ * Name: ohci_waiter * * Description: * Wait for USB devices to be connected to the OHCI hub. * ************************************************************************************/ #ifdef CONFIG_SAMA5_OHCI static int ohci_waiter(int argc, char *argv[]) { #ifdef CONFIG_DEBUG_USB return usbhost_waiter(g_ohciconn, "OHCI"); #else return usbhost_waiter(g_ohciconn); #endif } #endif /************************************************************************************ * Name: ehci_waiter * * Description: * Wait for USB devices to be connected to the EHCI hub. * ************************************************************************************/ #ifdef CONFIG_SAMA5_EHCI static int ehci_waiter(int argc, char *argv[]) { #ifdef CONFIG_DEBUG_USB return usbhost_waiter(g_ehciconn, "EHCI"); #else return usbhost_waiter(g_ehciconn); #endif } #endif /************************************************************************************ * Public Functions ************************************************************************************/ /************************************************************************************ * Name: sam_usbinitialize * * Description: * Called from sam_usbinitialize very early in inialization to setup USB-related * GPIO pins for the SAMA5D3-Xplained board. * * USB Ports * The SAMA5D3 series-MB features three USB communication ports: * * 1. Port A Host High Speed (EHCI) and Full Speed (OHCI) multiplexed with * USB Device High Speed Micro AB connector, J20 * * 2. Port B Host High Speed (EHCI) and Full Speed (OHCI) standard type A * connector, J19 upper port * * 3. Port C Host Full Speed (OHCI) only standard type A connector, J19 * lower port * * The two USB host ports (only) are equipped with 500-mA high-side power * switch for self-powered and bus-powered applications. * * The USB device port A (J6) features a VBUS insert detection function. * * Port A * * PIO Signal Name Function * ---- ----------- ------------------------------------------------------- * PE9 VBUS_SENSE VBus detection * * Note: No VBus power switch enable on port A. I think that this limits * this port to a device port or as a host port for self-powered devices * only. * * Port B * * PIO Signal Name Function * ---- ----------- ------------------------------------------------------- * PE4 EN5V_USBB VBus power enable (via MN3 power switch). To the A1 * pin of J19 Dual USB A connector * * Port C * * PIO Signal Name Function * ---- ----------- ------------------------------------------------------- * PE3 EN5V_USBC VBus power enable (via MN3 power switch). To the B1 * pin of J19 Dual USB A connector * * Both Ports B and C * * PIO Signal Name Function * ---- ----------- ------------------------------------------------------- * PE5 OVCUR_USB Combined over-current indication from port A and B * * That offers a lot of flexibility. However, here we enable the ports only * as follows: * * Port A -- USB device * Port B -- EHCI host * Port C -- OHCI host * ************************************************************************************/ void weak_function sam_usbinitialize(void) { #ifdef HAVE_USBDEV /* Configure Port A to support the USB device function */ sam_configpio(PIO_USBA_VBUS_SENSE); /* VBUS sense */ /* TODO: Configure an interrupt on VBUS sense */ #endif #ifdef HAVE_USBHOST #ifdef CONFIG_SAMA5_UHPHS_RHPORT1 /* Configure Port A to support the USB OHCI/EHCI function */ #ifdef PIO_USBA_VBUS_ENABLE /* SAMA5D3-Xplained has no port A VBUS enable */ sam_configpio(PIO_USBA_VBUS_ENABLE); /* VBUS enable, initially OFF */ #endif #endif #ifdef CONFIG_SAMA5_UHPHS_RHPORT2 /* Configure Port B to support the USB OHCI/EHCI function */ sam_configpio(PIO_USBB_VBUS_ENABLE); /* VBUS enable, initially OFF */ #endif #ifdef CONFIG_SAMA5_UHPHS_RHPORT3 /* Configure Port C to support the USB OHCI/EHCI function */ sam_configpio(PIO_USBC_VBUS_ENABLE); /* VBUS enable, initially OFF */ #endif #if defined(CONFIG_SAMA5_UHPHS_RHPORT2) || defined(CONFIG_SAMA5_UHPHS_RHPORT3) /* Configure Port B/C VBUS overrcurrent detection */ sam_configpio(PIO_USBBC_VBUS_OVERCURRENT); /* VBUS overcurrent */ #endif #endif /* HAVE_USBHOST */ } /*********************************************************************************** * Name: sam_usbhost_initialize * * Description: * Called at application startup time to initialize the USB host functionality. * This function will start a thread that will monitor for device * connection/disconnection events. * ***********************************************************************************/ #if HAVE_USBHOST int sam_usbhost_initialize(void) { pid_t pid; int ret; /* First, register all of the class drivers needed to support the drivers * that we care about */ #ifdef CONFIG_USBHOST_HUB /* Initialize USB hub class support */ ret = usbhost_hub_initialize(); if (ret < 0) { udbg("ERROR: usbhost_hub_initialize failed: %d\n", ret); } #endif #ifdef CONFIG_USBHOST_MSC /* Register theUSB host Mass Storage Class */ ret = usbhost_msc_initialize(); if (ret != OK) { udbg("ERROR: Failed to register the mass storage class: %d\n", ret); } #endif #ifdef CONFIG_USBHOST_CDCACM /* Register the CDC/ACM serial class */ ret = usbhost_cdcacm_initialize(); if (ret != OK) { udbg("ERROR: Failed to register the CDC/ACM serial class: %d\n", ret); } #endif #ifdef CONFIG_USBHOST_HIDKBD /* Register the USB host HID keyboard class driver */ ret = usbhost_kbdinit(); if (ret != OK) { udbg("ERROR: Failed to register the KBD class\n"); } #endif /* Then get an instance of the USB host interface. */ #ifdef CONFIG_SAMA5_OHCI /* Get an instance of the USB OHCI interface */ g_ohciconn = sam_ohci_initialize(0); if (!g_ohciconn) { udbg("ERROR: sam_ohci_initialize failed\n"); return -ENODEV; } /* Start a thread to handle device connection. */ pid = task_create("OHCI Monitor", CONFIG_SAMA5D3XPLAINED_USBHOST_PRIO, CONFIG_SAMA5D3XPLAINED_USBHOST_STACKSIZE, (main_t)ohci_waiter, (FAR char * const *)NULL); if (pid < 0) { udbg("ERROR: Failed to create ohci_waiter task: %d\n", ret); return -ENODEV; } #endif #ifdef CONFIG_SAMA5_EHCI /* Get an instance of the USB EHCI interface */ g_ehciconn = sam_ehci_initialize(0); if (!g_ehciconn) { udbg("ERROR: sam_ehci_initialize failed\n"); return -ENODEV; } /* Start a thread to handle device connection. */ pid = task_create("EHCI Monitor", CONFIG_SAMA5D3XPLAINED_USBHOST_PRIO, CONFIG_SAMA5D3XPLAINED_USBHOST_STACKSIZE, (main_t)ehci_waiter, (FAR char * const *)NULL); if (pid < 0) { udbg("ERROR: Failed to create ehci_waiter task: %d\n", ret); return -ENODEV; } #endif return OK; } #endif /*********************************************************************************** * Name: sam_usbhost_vbusdrive * * Description: * Enable/disable driving of VBUS 5V output. This function must be provided by * each platform that implements the OHCI or EHCI host interface * * Input Parameters: * rhport - Selects root hub port to be powered host interface. See SAM_RHPORT_* * definitions above. * enable - true: enable VBUS power; false: disable VBUS power * * Returned Value: * None * ***********************************************************************************/ #if HAVE_USBHOST void sam_usbhost_vbusdrive(int rhport, bool enable) { pio_pinset_t pinset = 0; uinfo("RHPort%d: enable=%d\n", rhport+1, enable); /* Pick the PIO configuration associated with the selected root hub port */ switch (rhport) { case SAM_RHPORT1: #if !defined(CONFIG_SAMA5_UHPHS_RHPORT1) udbg("ERROR: RHPort1 is not available in this configuration\n"); return; #elif !defined(PIO_USBA_VBUS_ENABLE) /* SAMA5D3-Xplained has no port A VBUS enable */ udbg("ERROR: RHPort1 has no VBUS enable\n"); return; #else pinset = PIO_USBA_VBUS_ENABLE; break; #endif case SAM_RHPORT2: #ifndef CONFIG_SAMA5_UHPHS_RHPORT2 udbg("ERROR: RHPort2 is not available in this configuration\n"); return; #else pinset = PIO_USBB_VBUS_ENABLE; break; #endif case SAM_RHPORT3: #ifndef CONFIG_SAMA5_UHPHS_RHPORT3 udbg("ERROR: RHPort3 is not available in this configuration\n"); return; #else pinset = PIO_USBC_VBUS_ENABLE; break; #endif default: udbg("ERROR: RHPort%d is not supported\n", rhport+1); return; } /* Then enable or disable VBUS power (active low for SP2526A-2) */ if (enable) { /* Enable the Power Switch by driving the enable pin low */ sam_piowrite(pinset, false); } else { /* Disable the Power Switch by driving the enable pin high */ sam_piowrite(pinset, true); } } #endif /************************************************************************************ * Name: sam_setup_overcurrent * * Description: * Setup to receive an interrupt-level callback if an overcurrent condition is * detected on port B or C. * * REVISIT: Since this is a common signal, we will need to come up with some way * to inform both EHCI and OHCI drivers when this error occurs. * * Input Parameter: * handler - New overcurrent interrupt handler * * Returned value: * Old overcurrent interrupt handler * ************************************************************************************/ #if HAVE_USBHOST xcpt_t sam_setup_overcurrent(xcpt_t handler) { #if defined(CONFIG_SAMA5_PIOD_IRQ) && (defined(CONFIG_SAMA5_UHPHS_RHPORT2) || \ defined(CONFIG_SAMA5_UHPHS_RHPORT3)) xcpt_t oldhandler; irqstate_t flags; /* Disable interrupts until we are done. This guarantees that the * following operations are atomic. */ flags = enter_critical_section(); /* Get the old interrupt handler and save the new one */ oldhandler = g_ochandler; g_ochandler = handler; /* Configure the interrupt */ sam_pioirq(PIO_USBBC_VBUS_OVERCURRENT); (void)irq_attach(IRQ_USBBC_VBUS_OVERCURRENT, handler); sam_pioirqenable(IRQ_USBBC_VBUS_OVERCURRENT); /* Return the old handler (so that it can be restored) */ leave_critical_section(flags); return oldhandler; #else return NULL; #endif } #endif /* CONFIG_SAMA5_PIOD_IRQ ... */ /************************************************************************************ * Name: sam_usbsuspend * * Description: * Board logic must provide the sam_usbsuspend logic if the USBDEV driver is * used. This function is called whenever the USB enters or leaves suspend mode. * This is an opportunity for the board logic to shutdown clocks, power, etc. * while the USB is suspended. * ************************************************************************************/ #ifdef CONFIG_USBDEV void sam_usbsuspend(FAR struct usbdev_s *dev, bool resume) { ullerr("resume: %d\n", resume); } #endif #endif /* CONFIG_SAMA5_UHPHS || CONFIG_SAMA5_UDPHS */