/************************************************************************************ * configs/stm32f4discovery/include/board.h * * Copyright (C) 2012, 2014-2016 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ************************************************************************************/ #ifndef __CONFIG_STM32F4DISCOVERY_INCLUDE_BOARD_H #define __CONFIG_STM32F4DISCOVERY_INCLUDE_BOARD_H /************************************************************************************ * Included Files ************************************************************************************/ #include #ifndef __ASSEMBLY__ # include # include #endif /************************************************************************************ * Pre-processor Definitions ************************************************************************************/ /* Clocking *************************************************************************/ /* The STM32F4 Discovery board features a single 8MHz crystal. Space is provided * for a 32kHz RTC backup crystal, but it is not stuffed. * * This is the canonical configuration: * System Clock source : PLL (HSE) * SYSCLK(Hz) : 168000000 Determined by PLL configuration * HCLK(Hz) : 168000000 (STM32_RCC_CFGR_HPRE) * AHB Prescaler : 1 (STM32_RCC_CFGR_HPRE) * APB1 Prescaler : 4 (STM32_RCC_CFGR_PPRE1) * APB2 Prescaler : 2 (STM32_RCC_CFGR_PPRE2) * HSE Frequency(Hz) : 8000000 (STM32_BOARD_XTAL) * PLLM : 8 (STM32_PLLCFG_PLLM) * PLLN : 336 (STM32_PLLCFG_PLLN) * PLLP : 2 (STM32_PLLCFG_PLLP) * PLLQ : 7 (STM32_PLLCFG_PLLQ) * Main regulator output voltage : Scale1 mode Needed for high speed SYSCLK * Flash Latency(WS) : 5 * Prefetch Buffer : OFF * Instruction cache : ON * Data cache : ON * Require 48MHz for USB OTG FS, : Enabled * SDIO and RNG clock */ /* HSI - 16 MHz RC factory-trimmed * LSI - 32 KHz RC * HSE - On-board crystal frequency is 8MHz * LSE - 32.768 kHz */ #define STM32_BOARD_XTAL 8000000ul #define STM32_HSI_FREQUENCY 16000000ul #define STM32_LSI_FREQUENCY 32000 #define STM32_HSE_FREQUENCY STM32_BOARD_XTAL #define STM32_LSE_FREQUENCY 32768 /* Main PLL Configuration. * * PLL source is HSE * PLL_VCO = (STM32_HSE_FREQUENCY / PLLM) * PLLN * = (8,000,000 / 8) * 336 * = 336,000,000 * SYSCLK = PLL_VCO / PLLP * = 336,000,000 / 2 = 168,000,000 * USB OTG FS, SDIO and RNG Clock * = PLL_VCO / PLLQ * = 48,000,000 */ #define STM32_PLLCFG_PLLM RCC_PLLCFG_PLLM(8) #define STM32_PLLCFG_PLLN RCC_PLLCFG_PLLN(336) #define STM32_PLLCFG_PLLP RCC_PLLCFG_PLLP_2 #define STM32_PLLCFG_PLLQ RCC_PLLCFG_PLLQ(7) #define STM32_SYSCLK_FREQUENCY 168000000ul /* AHB clock (HCLK) is SYSCLK (168MHz) */ #define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ #define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY #define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* same as above, to satisfy compiler */ /* APB1 clock (PCLK1) is HCLK/4 (42MHz) */ #define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd4 /* PCLK1 = HCLK / 4 */ #define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/4) /* Timers driven from APB1 will be twice PCLK1 */ #define STM32_APB1_TIM2_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM3_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM4_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM5_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM6_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM7_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM12_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM13_CLKIN (2*STM32_PCLK1_FREQUENCY) #define STM32_APB1_TIM14_CLKIN (2*STM32_PCLK1_FREQUENCY) /* APB2 clock (PCLK2) is HCLK/2 (84MHz) */ #define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLKd2 /* PCLK2 = HCLK / 2 */ #define STM32_PCLK2_FREQUENCY (STM32_HCLK_FREQUENCY/2) /* Timers driven from APB2 will be twice PCLK2 */ #define STM32_APB2_TIM1_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM8_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM9_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM10_CLKIN (2*STM32_PCLK2_FREQUENCY) #define STM32_APB2_TIM11_CLKIN (2*STM32_PCLK2_FREQUENCY) /* Timer Frequencies, if APBx is set to 1, frequency is same to APBx * otherwise frequency is 2xAPBx. * Note: TIM1,8 are on APB2, others on APB1 */ #define BOARD_TIM1_FREQUENCY STM32_HCLK_FREQUENCY #define BOARD_TIM2_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM3_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM4_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM5_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM6_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM7_FREQUENCY (STM32_HCLK_FREQUENCY / 2) #define BOARD_TIM8_FREQUENCY STM32_HCLK_FREQUENCY /* SDIO dividers. Note that slower clocking is required when DMA is disabled * in order to avoid RX overrun/TX underrun errors due to delayed responses * to service FIFOs in interrupt driven mode. These values have not been * tuned!!! * * SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(118+2)=400 KHz */ #define SDIO_INIT_CLKDIV (118 << SDIO_CLKCR_CLKDIV_SHIFT) /* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz */ #ifdef CONFIG_SDIO_DMA # define SDIO_MMCXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) #else # define SDIO_MMCXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) #endif /* DMA ON: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(1+2)=16 MHz * DMA OFF: SDIOCLK=48MHz, SDIO_CK=SDIOCLK/(2+2)=12 MHz */ #ifdef CONFIG_SDIO_DMA # define SDIO_SDXFR_CLKDIV (1 << SDIO_CLKCR_CLKDIV_SHIFT) #else # define SDIO_SDXFR_CLKDIV (2 << SDIO_CLKCR_CLKDIV_SHIFT) #endif /* LED definitions ******************************************************************/ /* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any * way. The following definitions are used to access individual LEDs. */ /* LED index values for use with board_userled() */ #define BOARD_LED1 0 #define BOARD_LED2 1 #define BOARD_LED3 2 #define BOARD_LED4 3 #define BOARD_NLEDS 4 #define BOARD_LED_GREEN BOARD_LED1 #define BOARD_LED_ORANGE BOARD_LED2 #define BOARD_LED_RED BOARD_LED3 #define BOARD_LED_BLUE BOARD_LED4 /* LED bits for use with board_userled_all() */ #define BOARD_LED1_BIT (1 << BOARD_LED1) #define BOARD_LED2_BIT (1 << BOARD_LED2) #define BOARD_LED3_BIT (1 << BOARD_LED3) #define BOARD_LED4_BIT (1 << BOARD_LED4) /* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 4 LEDs on board the * stm32f4discovery. The following definitions describe how NuttX controls the LEDs: */ #define LED_STARTED 0 /* LED1 */ #define LED_HEAPALLOCATE 1 /* LED2 */ #define LED_IRQSENABLED 2 /* LED1 + LED2 */ #define LED_STACKCREATED 3 /* LED3 */ #define LED_INIRQ 4 /* LED1 + LED3 */ #define LED_SIGNAL 5 /* LED2 + LED3 */ #define LED_ASSERTION 6 /* LED1 + LED2 + LED3 */ #define LED_PANIC 7 /* N/C + N/C + N/C + LED4 */ /* Button definitions ***************************************************************/ /* The STM32F4 Discovery supports one button: */ #define BUTTON_USER 0 #define NUM_BUTTONS 1 #define BUTTON_USER_BIT (1 << BUTTON_USER) /* Alternate function pin selections ************************************************/ /* CAN */ #ifndef CONFIG_STM32_FSMC # define GPIO_CAN1_RX GPIO_CAN1_RX_3 # define GPIO_CAN1_TX GPIO_CAN1_TX_3 #endif #ifndef CONFIG_STM32_ETHMAC # define GPIO_CAN2_RX GPIO_CAN2_RX_1 # define GPIO_CAN2_TX GPIO_CAN2_TX_1 #endif /* USART2: * * The STM32F4 Discovery has no on-board serial devices, but the console is * brought out to PA2 (TX) and PA3 (RX) for connection to an external serial * device. (See the README.txt file for other options) * * These pins selections, however, conflict with pin usage on the STM32F4DIS-BB. */ #ifndef CONFIG_STM32F4DISBB # define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */ # define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */ #endif /* USART3: * * Used in pseudoterm configuration and also with the BT860 HCI UART. * RTS/CTS Flow control support is need by the HCI UART. */ #define GPIO_USART3_TX GPIO_USART3_TX_1 /* PB10 */ #define GPIO_USART3_RX GPIO_USART3_RX_1 /* PB11 */ #define GPIO_USART3_CTS GPIO_USART3_CTS_1 /* PB13 */ #define GPIO_USART3_RTS GPIO_USART3_RTS_1 /* PB14 */ /* USART6: * * The STM32F4DIS-BB base board provides RS-232 drivers and a DB9 connector * for USART6. This is the preferred serial console for use with the STM32F4DIS-BB. */ #define GPIO_USART6_RX GPIO_USART6_RX_1 /* PC7 */ #define GPIO_USART6_TX GPIO_USART6_TX_1 /* PC6 */ /* PWM * * The STM32F4 Discovery has no real on-board PWM devices, but the board can be * configured to output a pulse train using TIM4 CH2 on PD13. */ #define GPIO_TIM4_CH2OUT GPIO_TIM4_CH2OUT_2 /* RGB LED * * R = TIM1 CH1 on PE9 | G = TIM2 CH2 on PA1 | B = TIM3 CH3 on PB0 */ #define GPIO_TIM1_CH1OUT GPIO_TIM1_CH1OUT_2 #define GPIO_TIM2_CH2OUT GPIO_TIM2_CH2OUT_1 #define GPIO_TIM3_CH3OUT GPIO_TIM3_CH3OUT_1 /* SPI - There is a MEMS device on SPI1 using these pins: */ #define GPIO_SPI1_MISO GPIO_SPI1_MISO_1 #define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_1 #define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* SPI2 - Test MAX31855 on SPI2 PB10 = SCK, PB14 = MISO */ #define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 #define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 #define GPIO_SPI2_SCK GPIO_SPI2_SCK_1 /* I2S3 - CS43L22 configuration uses I2S3 */ #define GPIO_I2S3_SD GPIO_I2S3_SD_2 #define GPIO_I2S3_CK GPIO_I2S3_CK_2 #define GPIO_I2S3_WS GPIO_I2S3_WS_1 #define DMACHAN_I2S3_RX DMAMAP_SPI3_RX_2 #define DMACHAN_I2S3_TX DMAMAP_SPI3_TX_2 /* I2C. Only I2C1 is available on the stm32f4discovery. I2C1_SCL and I2C1_SDA are * available on the following pins: * * - PB6 is I2C1_SCL * - PB9 is I2C1_SDA */ #define GPIO_I2C1_SCL GPIO_I2C1_SCL_1 #define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 /* Timer Inputs/Outputs (see the README.txt file for options) */ #define GPIO_TIM2_CH1IN GPIO_TIM2_CH1IN_2 #define GPIO_TIM2_CH2IN GPIO_TIM2_CH2IN_1 #define GPIO_TIM8_CH1IN GPIO_TIM8_CH1IN_1 #define GPIO_TIM8_CH2IN GPIO_TIM8_CH2IN_1 /* Ethernet *************************************************************************/ #if defined(CONFIG_STM32F4DISBB) && defined(CONFIG_STM32_ETHMAC) /* RMII interface to the LAN8720 PHY */ # ifndef CONFIG_STM32_RMII # error CONFIG_STM32_RMII must be defined # endif /* Clocking is provided by an external 25Mhz XTAL */ # ifndef CONFIG_STM32_RMII_EXTCLK # error CONFIG_STM32_RMII_EXTCLK must be defined # endif /* Pin disambiguation */ # define GPIO_ETH_RMII_TX_EN GPIO_ETH_RMII_TX_EN_1 # define GPIO_ETH_RMII_TXD0 GPIO_ETH_RMII_TXD0_1 # define GPIO_ETH_RMII_TXD1 GPIO_ETH_RMII_TXD1_1 # define GPIO_ETH_PPS_OUT GPIO_ETH_PPS_OUT_1 #endif /* DMA Channl/Stream Selections *****************************************************/ /* Stream selections are arbitrary for now but might become important in the future * if we set aside more DMA channels/streams. * * SDIO DMA * DMAMAP_SDIO_1 = Channel 4, Stream 3 * DMAMAP_SDIO_2 = Channel 4, Stream 6 */ #define DMAMAP_SDIO DMAMAP_SDIO_1 #endif /* __CONFIG_STM32F4DISCOVERY_INCLUDE_BOARD_H */