/**************************************************************************** * config/sam4l-xplained/src/sam_ug2832hsweg04.c * * Copyright (C) 2013, 2015 Gregory Nutt. All rights reserved. * Author: Gregory Nutt * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /* OLED1 Connector: * * OLED1 EXT1 EXT2 Other use of either pin * ----------------- -------------------- -------------------- ------------------------------------ * 1 ID 1 1 * 2 GND 2 GND 2 * 3 BUTTON2 3 PA04 ADCIFE/AD0 3 PA07 ADCIFE/AD2 * 4 BUTTON3 4 PA05 ADCIFE/AD1 4 PB02 ADCIFE/AD3 * 5 DATA_CMD_SEL 5 PB12 GPIO 5 PC08 GPIO PB12 and PC8 on EXT5 * 6 LED3 6 PC02 GPIO 6 PB10 GPIO PB10 on EXT5 * 7 LED1 7 PC00 TC/1/A0 7 PC04 TC/1/A2 * 8 LED2 8 PC01 TC/1/B0 8 PC05 TC/1/B2 PC05 on EXT5 * 9 BUTTON1 9 PC25 EIC/EXTINT2 9 PC06 EIC/EXTINT8 PC25 on EXT5 * 10 DISPLAY_RESET 10 PB13 SPI/NPCS1 10 PC09 GPIO PB13 on EXT5 * 11 N/C 11 PA23 TWIMS/0/TWD 11 PB14 TWIMS/3/TWD PB14 on EXT3&4, PA23 and PB14 on EXT5 * 12 N/C 12 PA24 TWIMS/0/TWCK 12 PB15 TWIMS/3/TWCK PB15 on EXT3&4, PA24 and PB15 on EXT5 * 13 N/C 13 PB00 USART/0/RXD 13 PC26 USART/1/RXD PB00 on EXT4, PC26 on EXT3&5 * 14 N/C 14 PB01 USART/0/TXD 14 PC27 USART/1/TXD PB01 on EXT4, PC27 on EXT3&5 * 15 DISPLAY_SS 15 PC03 SPI/NPCS0 15 PB11 SPI/NPCS2 PB11 on EXT5 * 16 SPI_MOSI 16 PA22 SPI/MOSI 16 PA22 SPI/MOSI PA22 on EXT5 * 17 N/C 17 PA21 SPI/MISO 17 PA21 SPI/MISO PA21 on EXT5 * 18 SPI_SCK 18 PC30 SPI/SCK 18 PC30 SPI/SCK PC30 on EXT5 * 19 GND 19 GND GND * 20 VCC 20 VCC VCC * * OLED1 signals * * DATA_CMD_SEL - Data/command select. Used to choose whether the * communication is data to the display memory or a command to the LCD * controller. High = data, low = command * DISPLAY_RESET - Reset signal to the OLED display, active low. Used during * initialization of the display. * DISPLAY_SS - SPI slave select signal, must be held low during SPI * communication. * SPI_MOSI - SPI master out, slave in signal. Used to write data to the * display * SPI_SCK SPI - clock signal, generated by the master. */ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include "sam_gpio.h" #include "sam_spi.h" #include "sam4l-xplained.h" #ifdef CONFIG_SAM4L_XPLAINED_OLED1MODULE /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Configuration ************************************************************/ /* The pin configurations here require that SPI1 is selected */ #ifndef CONFIG_LCD_SSD1306 # error "The OLED driver requires CONFIG_LCD_SSD1306 in the configuration" #endif #ifndef CONFIG_LCD_UG2832HSWEG04 # error "The OLED driver requires CONFIG_LCD_UG2832HSWEG04 in the configuration" #endif #ifndef CONFIG_SAM34_SPI0 # error "The OLED driver requires CONFIG_SAM34_SPI0 in the configuration" #endif #ifndef CONFIG_SPI_CMDDATA # error "The OLED driver requires CONFIG_SPI_CMDDATA in the configuration" #endif /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: board_graphics_setup * * Description: * Called by NX initialization logic to configure the OLED. * ****************************************************************************/ FAR struct lcd_dev_s *board_graphics_setup(unsigned int devno) { FAR struct spi_dev_s *spi; FAR struct lcd_dev_s *dev; /* Configure the OLED GPIOs. This initial configuration is RESET low, * putting the OLED into reset state. */ (void)sam_configgpio(GPIO_OLED_RST); /* Wait a bit then release the OLED from the reset state */ up_mdelay(20); sam_gpiowrite(GPIO_OLED_RST, true); /* Get the SPI1 port interface */ spi = sam_spibus_initialize(OLED_CSNO); if (!spi) { lcderr("ERROR: Failed to initialize SPI port 1\n"); } else { /* Bind the SPI port to the OLED */ dev = ssd1306_initialize(spi, NULL, devno); if (!dev) { lcderr("ERROR: Failed to bind SPI port 1 to OLED %d: %d\n", devno); } else { lcdinfo("Bound SPI port 1 to OLED %d\n", devno); /* And turn the OLED on */ (void)dev->setpower(dev, CONFIG_LCD_MAXPOWER); return dev; } } return NULL; } #endif /* CONFIG_SAM4L_XPLAINED_OLED1MODULE */