/**************************************************************************** * drivers/can/sja1000.c * * SJA1000 CAN driver based on esp32c3_twai.c * * License header retained from original source. * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "sja1000.h" #include #ifdef CONFIG_CAN_SJA1000 /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Configuration * ************************************************************/ #if defined(CONFIG_CAN_SJA1000_DEBUG) #define cantrace _info #else #define cantrace _none #endif /* CONFIG_CAN_SJA1000_DEBUG */ /* Default values written to various registers on initialization */ #define SJA1000_INIT_TEC 0 #define SJA1000_INIT_REC 0 #define SJA1000_INIT_EWL 96 #define SJA1000_ACCEPTANCE_CODE 0x0 /* 32-bit address to match */ #define SJA1000_ACCEPTANCE_MASK 0xffffffff /* 32-bit address mask */ /**************************************************************************** * Private Types ****************************************************************************/ /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* SJA1000 Register access */ #ifdef CONFIG_CANBUS_REGDEBUG static void sja1000_printreg(uint32_t addr, uint32_t value); #endif /* SJA1000 methods */ static void sja1000_reset(struct can_dev_s *dev); static int sja1000_setup(struct can_dev_s *dev); static void sja1000_shutdown(struct can_dev_s *dev); static void sja1000_rxint(struct can_dev_s *dev, bool enable); static void sja1000_txint(struct can_dev_s *dev, bool enable); static int sja1000_ioctl(struct can_dev_s *dev, int cmd, unsigned long arg); static int sja1000_remoterequest(struct can_dev_s *dev, uint16_t id); static int sja1000_send(struct can_dev_s *dev, struct can_msg_s *msg); static bool sja1000_txready(struct can_dev_s *dev); static bool sja1000_txempty(struct can_dev_s *dev); /* SJA1000 interrupts */ static int sja1000_interrupt(FAR struct sja1000_config_s *config, void *arg); /* SJA1000 acceptance filter */ static void sja1000_set_acc_filter(struct sja1000_dev_s *priv, uint32_t code, uint32_t mask, bool single_filter); /* SJA1000 bit-timing initialization */ static int sja1000_baud_rate(struct sja1000_dev_s *priv, int rate, int clock, int sjw, int sampl_pt, int flags); /**************************************************************************** * Private Data ****************************************************************************/ static const struct can_ops_s g_sja1000ops = { .co_reset = sja1000_reset, .co_setup = sja1000_setup, .co_shutdown = sja1000_shutdown, .co_rxint = sja1000_rxint, .co_txint = sja1000_txint, .co_ioctl = sja1000_ioctl, .co_remoterequest = sja1000_remoterequest, .co_send = sja1000_send, .co_txready = sja1000_txready, .co_txempty = sja1000_txempty, }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: sja1000_printreg * * Description: * Print the value read from a register. * * Input Parameters: * addr - The register address * value - The register value * * Returned Value: * None * ****************************************************************************/ #ifdef CONFIG_CANBUS_REGDEBUG static void sja1000_printreg(uint32_t addr, uint32_t value) { static uint32_t prevaddr; static uint32_t preval; static uint32_t count; /* Is this the same value that we read from the same register last time? * Are we polling the register? If so, suppress some of the output. */ if (addr == prevaddr && value == preval) { if (count == 0xffffffff || ++count > 3) { if (count == 4) { caninfo("...\n"); } return; } } /* No this is a new address or value */ else { /* Did we print "..." for the previous value? */ if (count > 3) { /* Yes.. then show how many times the value repeated */ caninfo("[repeats %" PRId32 " more times]\n", count - 3); } /* Save the new address, value, and count */ prevaddr = addr; preval = value; count = 1; } /* Show the register value read */ caninfo("%08" PRIx32 "->%08" PRIx32 "\n", addr, value); } #endif /* CONFIG_CANBUS_REGDEBUG */ /**************************************************************************** * Name: sja1000_reset * * Description: * Reset the SJA1000 device. Called early to initialize the hardware. *This function is called, before litex_sja1000_setup() and on error *conditions. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * * Returned Value: * None * ****************************************************************************/ static void sja1000_reset(struct can_dev_s *dev) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; irqstate_t flags; int ret; caninfo("SJA1000 Device %" PRIu8 "\n", port); #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ /* Disable the SJA1000 and stop ongoing transmissions */ uint32_t mode_value = SJA1000_RESET_MODE_M | SJA1000_LISTEN_ONLY_MODE_M; sja1000_putreg(priv, SJA1000_MODE_REG, mode_value); /* Enter Reset Mode */ sja1000_modifyreg32(priv, SJA1000_CLOCK_DIVIDER_REG, 0, SJA1000_EXT_MODE_M); sja1000_putreg(priv, SJA1000_INT_ENA_REG, 0); /* Disable interrupts */ sja1000_getreg(priv, SJA1000_STATUS_REG); /* Clear status bits */ sja1000_putreg(priv, SJA1000_TX_ERR_CNT_REG, SJA1000_INIT_TEC); /* TEC */ sja1000_putreg(priv, SJA1000_RX_ERR_CNT_REG, SJA1000_INIT_REC); /* REC */ sja1000_putreg(priv, SJA1000_ERR_WARNING_LIMIT_REG, SJA1000_INIT_EWL); /* EWL */ sja1000_set_acc_filter( priv, SJA1000_ACCEPTANCE_CODE, SJA1000_ACCEPTANCE_MASK, true); /* Set bit timing */ ret = sja1000_baud_rate(priv, config->bitrate, config->clk_freq, config->sjw, config->samplep, 0); if (ret != OK) { canerr("ERROR: Failed to set bit timing: %d\n", ret); } /* Restart the SJA1000 */ if (config->loopback) { /* Leave Reset Mode, enter Test Mode */ sja1000_putreg(priv, SJA1000_MODE_REG, SJA1000_SELF_TEST_MODE_M); } else { /* Leave Reset Mode */ sja1000_putreg(priv, SJA1000_MODE_REG, 0); } /* Abort transmission and clear overrun. * Command register can only be modified when in Operation Mode. */ sja1000_putreg(priv, SJA1000_CMD_REG, SJA1000_ABORT_TX_M | SJA1000_CLR_OVERRUN_M); #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ } /**************************************************************************** * Name: sja1000_setup * * Description: * Configure the SJA1000. This method is called the first time that the *SJA1000 device is opened. This will occur when the port is first opened. * This setup includes configuring and attaching SJA1000 interrupts. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * * Returned Value: * Zero on success; a negated errno on failure * ****************************************************************************/ static int sja1000_setup(struct can_dev_s *dev) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; irqstate_t flags; int ret = OK; caninfo("SJA1000 (%" PRIu8 ")\n", port); #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ sja1000_putreg(priv, SJA1000_INT_ENA_REG, SJA1000_DEFAULT_INTERRUPTS); /* clear latched interrupts */ sja1000_getreg(priv, SJA1000_INT_RAW_REG); /* Attach the SJA1000 interrupts and handler. */ ret = config->attach( config, (sja1000_handler_t)sja1000_interrupt, (FAR void *)dev); if (ret < 0) { canerr("ERROR: Failed to attach to IRQ Handler!\n"); return ret; } #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ return ret; } /**************************************************************************** * Name: sja1000_shutdown * * Description: * Disable the SJA1000. This method is called when the SJA1000 device is *closed. This method reverses the operation the setup method. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * * Returned Value: * None * ****************************************************************************/ static void sja1000_shutdown(struct can_dev_s *dev) { int ret; struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; cantrace("shutdown SJA1000 (%" PRIu8 ")\n", port); /* Detach the SJA1000 interrupts and handler. */ ret = config->detach(config); if (ret < 0) { canerr("ERROR: Failed to detach from IRQ Handler!\n"); } } /**************************************************************************** * Name: sja1000_rxint * * Description: * Call to enable or disable RX interrupts. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * enable - Enable or disable receive interrupt. * * Returned Value: * None * ****************************************************************************/ static void sja1000_rxint(struct can_dev_s *dev, bool enable) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; uint32_t regval; irqstate_t flags; cantrace("SJA1000 (%" PRIu8 ") enable: %d\n", port, enable); /* The INT_ENA register is also modified from the interrupt handler, * so we have to protect this code section. */ #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ regval = sja1000_getreg(priv, SJA1000_INT_ENA_REG); if (enable) { regval |= SJA1000_RX_INT_ENA_M; } else { regval &= ~SJA1000_RX_INT_ENA_M; } sja1000_putreg(priv, SJA1000_INT_ENA_REG, regval); #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ } /**************************************************************************** * Name: sja1000_txint * * Description: * Call to enable or disable TX interrupts. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * enable - Enable or disable transmit interrupt. * * Returned Value: * None * ****************************************************************************/ static void sja1000_txint(struct can_dev_s *dev, bool enable) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; uint32_t regval; irqstate_t flags; cantrace("SJA1000 (%" PRIu8 ") enable: %d\n", port, enable); /* Only disabling of the TX interrupt is supported here. The TX interrupt * is automatically enabled just before a message is sent in order to * avoid lost TX interrupts. */ if (!enable) { /* TX interrupts are also disabled from the interrupt handler, so we * have to protect this code section. */ #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ /* Disable all TX interrupts */ regval = sja1000_getreg(priv, SJA1000_INT_ENA_REG); regval &= ~(SJA1000_TX_INT_ENA_M); sja1000_putreg(priv, SJA1000_INT_ENA_REG, regval); #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ } cantrace("Exiting.\n"); } /**************************************************************************** * Name: sja1000_ioctl * * Description: * All ioctl calls will be routed through this method * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * cmd - A ioctl command. * arg - A ioctl argument. * * Returned Value: * Zero on success; a negated errno on failure * ****************************************************************************/ static int sja1000_ioctl(struct can_dev_s *dev, int cmd, unsigned long arg) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; int ret = -ENOTTY; uint8_t port = config->port; cantrace("SJA1000 (%" PRIu8 ") cmd=%04x arg=%lu\n", port, cmd, arg); /* Handle the command */ switch (cmd) { /* CANIOC_GET_BITTIMING: * Description: Return the current bit timing settings * Argument: A pointer to a write-able instance of struct * canioc_bittiming_s in which current bit timing * values will be returned. * Returned Value: Zero (OK) is returned on success. Otherwise -1 * (ERROR) is returned with the errno variable set * to indicate the nature of the error. * Dependencies: None */ case CANIOC_GET_BITTIMING: { struct canioc_bittiming_s *bt = (struct canioc_bittiming_s *)arg; uint32_t timing0; uint32_t timing1; uint32_t brp; DEBUGASSERT(bt != NULL); timing0 = sja1000_getreg(priv, SJA1000_BUS_TIMING_0_REG); timing1 = sja1000_getreg(priv, SJA1000_BUS_TIMING_1_REG); brp = ((timing0 & SJA1000_BAUD_PRESC_M) + 1) * 2; bt->bt_sjw = ((timing0 & SJA1000_SYNC_JUMP_WIDTH_M) >> SJA1000_SYNC_JUMP_WIDTH_S) + 1; bt->bt_tseg1 = ((timing1 & SJA1000_TIME_SEG1_M) >> SJA1000_TIME_SEG1_S) + 1; bt->bt_tseg2 = ((timing1 & SJA1000_TIME_SEG2_M) >> SJA1000_TIME_SEG2_S) + 1; bt->bt_baud = config->clk_freq / (brp * (bt->bt_tseg1 + bt->bt_tseg2 + 1)); cantrace("Retrieved baud rate. TS1: %" PRId8 " TS2: %" PRId8 " BRP: %" PRId32 "\n", bt->bt_tseg1, bt->bt_tseg2, brp); cantrace("timing0: 0x%" PRIx32 ", timing1: 0x%" PRIx32 " Baud: " "%" PRId32 "\n", timing0, timing1, bt->bt_baud); ret = OK; } break; /* Unsupported/unrecognized command */ default: canerr("ERROR: Unrecognized command: %04x\n", cmd); break; } return ret; } static int sja1000_remoterequest(struct can_dev_s *dev, uint16_t id) { canwarn("Remote request not implemented\n"); return -ENOSYS; } /**************************************************************************** * Name: sja1000_send * * Description: * Send one SJA1000 message. * * One SJA1000-message consists of a maximum of 10 bytes. A message is * composed of at least the first 2 bytes (when there are no data bytes). * * Byte 0: Bits 0-7: Bits 3-10 of the 11-bit SJA1000 identifier * Byte 1: Bits 5-7: Bits 0-2 of the 11-bit SJA1000 identifier * Bit 4: Remote Transmission Request (RTR) * Bits 0-3: Data Length Code (DLC) * Bytes 2-10: SJA1000 data * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * msg - A message to send. * * Returned Value: * Zero on success; a negated errno on failure * ****************************************************************************/ static int sja1000_send(struct can_dev_s *dev, struct can_msg_s *msg) { struct sja1000_dev_s *priv = (struct sja1000_dev_s *)dev->cd_priv; struct sja1000_config_s *config = priv->config; uint32_t regval; uint32_t i; uint32_t len; uint32_t id; uint32_t frame_info; irqstate_t flags; uint8_t port = config->port; int ret = OK; cantrace("SJA1000 (%" PRIu8 ") ID: %" PRIu32 " DLC: %" PRIu8 "\n", port, (uint32_t)msg->cm_hdr.ch_id, msg->cm_hdr.ch_dlc); len = (uint32_t)msg->cm_hdr.ch_dlc; if (len > CAN_MAXDATALEN) len = CAN_MAXDATALEN; frame_info = len; if (msg->cm_hdr.ch_rtr) { frame_info |= (1 << 6); } #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ /* Make sure that TX interrupts are enabled BEFORE sending the * message. * * NOTE: The INT_ENA is also modified from the interrupt handler, but the * following is safe because interrupts are disabled here. */ regval = sja1000_getreg(priv, SJA1000_INT_ENA_REG); regval |= SJA1000_TX_INT_ENA_M; sja1000_putreg(priv, SJA1000_INT_ENA_REG, regval); /* Set up the transfer */ #ifdef CONFIG_CAN_EXTID if (msg->cm_hdr.ch_extid) { /* The provided ID should be 29 bits */ id = (uint32_t)msg->cm_hdr.ch_id; DEBUGASSERT((id & ~CAN_MAX_EXTMSGID) == 0); frame_info |= (1 << 7); sja1000_putreg(priv, SJA1000_DATA_0_REG, frame_info); id <<= 3; sja1000_putreg(priv, SJA1000_DATA_4_REG, id & 0xff); id >>= 8; sja1000_putreg(priv, SJA1000_DATA_3_REG, id & 0xff); id >>= 8; sja1000_putreg(priv, SJA1000_DATA_2_REG, id & 0xff); id >>= 8; sja1000_putreg(priv, SJA1000_DATA_1_REG, id & 0xff); for (i = 0; i < len; i++) { sja1000_putreg(priv, (SJA1000_DATA_5_REG + i), msg->cm_data[i]); } } else #endif { /* The provided ID should be 11 bits */ id = (uint32_t)msg->cm_hdr.ch_id; DEBUGASSERT((id & ~CAN_MAX_STDMSGID) == 0); sja1000_putreg(priv, SJA1000_DATA_0_REG, frame_info); id <<= 5; sja1000_putreg(priv, SJA1000_DATA_1_REG, (id >> 8) & 0xff); sja1000_putreg(priv, SJA1000_DATA_2_REG, id & 0xff); for (i = 0; i < len; i++) { sja1000_putreg(priv, (SJA1000_DATA_3_REG + i), msg->cm_data[i]); } } /* Send the message */ if (config->loopback) { sja1000_putreg(priv, SJA1000_CMD_REG, SJA1000_SELF_RX_REQ_M | SJA1000_ABORT_TX_M); } else { sja1000_putreg(priv, SJA1000_CMD_REG, SJA1000_TX_REQ_M); } #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ return ret; } /**************************************************************************** * Name: sja1000_txready * * Description: * Return true if the SJA1000 hardware can accept another TX message. * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * * Returned Value: * True if the SJA1000 hardware is ready to accept another TX message. * ****************************************************************************/ static bool sja1000_txready(struct can_dev_s *dev) { struct sja1000_dev_s *priv = dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; uint32_t regval = sja1000_getreg(priv, SJA1000_STATUS_REG); caninfo("SJA1000 (%" PRIu8 ") txready: %d\n", port, ((regval & SJA1000_TX_BUF_ST_M) != 0)); return ((regval & SJA1000_TX_BUF_ST_M) != 0); } /**************************************************************************** * Name: sja1000_txempty * * Description: * Return true if all message have been sent. If for example, the SJA1000 * hardware implements FIFOs, then this would mean the transmit FIFO is * empty. This method is called when the driver needs to make sure that * all characters are "drained" from the TX hardware before calling * co_shutdown(). * * Input Parameters: * dev - An instance of the "upper half" CAN driver state structure. * * Returned Value: * True if there are no pending TX transfers in the SJA1000 hardware. * ****************************************************************************/ static bool sja1000_txempty(struct can_dev_s *dev) { struct sja1000_dev_s *priv = dev->cd_priv; struct sja1000_config_s *config = priv->config; uint8_t port = config->port; uint32_t regval = sja1000_getreg(priv, SJA1000_STATUS_REG); caninfo("SJA1000 (%" PRIu8 ") txempty: %d\n", port, ((regval & SJA1000_TX_BUF_ST_M) != 0)); return ((regval & SJA1000_TX_BUF_ST_M) != 0); } /**************************************************************************** * Name: sja1000_interrupt * * Description: * SJA1000 RX/TX interrupt handler * * Input Parameters: * irq - The IRQ number of the interrupt. * context - The register state save array at the time of the interrupt. * arg - The pointer to driver structure. * * Returned Value: * Zero on success; a negated errno on failure * ****************************************************************************/ static int sja1000_interrupt(FAR struct sja1000_config_s *config, void *arg) { #ifdef CONFIG_CAN_SJA1000 struct can_dev_s *dev = (struct can_dev_s *)arg; struct sja1000_dev_s *priv = dev->cd_priv; struct can_hdr_s hdr; uint8_t data[8]; uint32_t frame_info; uint32_t len; uint32_t datastart; uint32_t regval; uint32_t i; /* Read the interrupt register results in clearing bits */ regval = sja1000_getreg(priv, SJA1000_INT_RAW_REG); cantrace("Entered. Regval = 0x%" PRIx32 "\n", regval); /* Check for a receive interrupt */ if ((regval & SJA1000_RX_INT_ST_M) != 0) { memset(&hdr, 0, sizeof(hdr)); memset(data, 0, sizeof(data)); frame_info = sja1000_getreg(priv, SJA1000_DATA_0_REG); /* Construct the SJA1000 header */ if (frame_info & (1 << 6)) { hdr.ch_rtr = 1; } #ifdef CONFIG_CAN_EXTID if (frame_info & (1 << 7)) { /* The provided ID should be 29 bits */ hdr.ch_extid = 1; hdr.ch_id = (sja1000_getreg(priv, SJA1000_DATA_1_REG) << 21) + (sja1000_getreg(priv, SJA1000_DATA_2_REG) << 13) + (sja1000_getreg(priv, SJA1000_DATA_3_REG) << 5) + (sja1000_getreg(priv, SJA1000_DATA_4_REG) >> 3); datastart = SJA1000_DATA_5_REG; } else #endif /* CONFIG_CAN_EXTID */ { /* The provided ID should be 11 bits */ hdr.ch_id = (sja1000_getreg(priv, SJA1000_DATA_1_REG) << 3) + (sja1000_getreg(priv, SJA1000_DATA_2_REG) >> 5); datastart = SJA1000_DATA_3_REG; } len = frame_info & 0xf; if (len > CAN_MAXDATALEN) { len = CAN_MAXDATALEN; } hdr.ch_dlc = len; for (i = 0; i < len; i++) { data[i] = sja1000_getreg(priv, (datastart + i)); } /* Release the receive buffer */ sja1000_putreg(priv, SJA1000_CMD_REG, SJA1000_RELEASE_BUF_M); #ifdef CONFIG_CAN_ERRORS hdr.ch_error = 0; /* Error reporting not supported */ #endif /* CONFIG_CAN_ERRORS */ can_receive(dev, &hdr, data); } /* Check for TX buffer complete */ if ((regval & SJA1000_TX_INT_ST_M) != 0) { /* Disable all further TX buffer interrupts */ regval = sja1000_getreg(priv, SJA1000_INT_ENA_REG); regval &= ~SJA1000_TX_INT_ENA_M; sja1000_putreg(priv, SJA1000_INT_ENA_REG, regval); /* Indicate that the TX is done and a new TX buffer is available */ can_txdone(dev); } #endif /* CONFIG_CAN_SJA1000 */ return OK; } /**************************************************************************** * Name: sja1000_set_acc_filter * * Description: * Call to set acceptance filter. * Must be called in reset mode. * * Input Parameters: * priv - Private SJA1000 context * code - Acceptance Code. * mask - Acceptance Mask. * single_filter - Whether to enable single filter mode. * * Returned Value: * None * ****************************************************************************/ static void sja1000_set_acc_filter(struct sja1000_dev_s *priv, uint32_t code, uint32_t mask, bool single_filter) { uint32_t regval; uint32_t code_swapped = __builtin_bswap32(code); uint32_t mask_swapped = __builtin_bswap32(mask); regval = sja1000_getreg(priv, SJA1000_MODE_REG); if (single_filter) { regval |= SJA1000_RX_FILTER_MODE_M; } else { regval &= ~(SJA1000_RX_FILTER_MODE_M); } sja1000_putreg(priv, SJA1000_MODE_REG, regval); for (int i = 0; i < 4; i++) { sja1000_putreg(priv, (SJA1000_DATA_0_REG + i), ((code_swapped >> (i * 8)) & 0xff)); sja1000_putreg(priv, (SJA1000_DATA_4_REG + i), ((mask_swapped >> (i * 8)) & 0xff)); } } /**************************************************************************** * Name: sja1000_baud_rate * * Description: * Set the CAN bus timing registers based on the configured bit-rate and * sample point position. * * The bit timing logic monitors the serial bus-line and performs sampling * and adjustment of the sample point by synchronizing on the start-bit edge * and resynchronizing on the following edges. * * Its operation may be explained simply by splitting nominal bit time into * three segments as follows: * * 1. Synchronization segment (SYNC_SEG): a bit change is expected to occur * within this time segment. It has a fixed length of one time quantum * (1 x tCAN). * 2. Bit segment 1 (BS1): defines the location of the sample point. It * includes the PROP_SEG and PHASE_SEG1 of the CAN standard. Its duration * is programmable between 1 and 16 time quanta but may be automatically * lengthened to compensate for positive phase drifts due to differences * in the frequency of the various nodes of the network. * 3. Bit segment 2 (BS2): defines the location of the transmit point. It * represents the PHASE_SEG2 of the CAN standard. Its duration is * programmable between 1 and 8 time quanta but may also be automatically * shortened to compensate for negative phase drifts. * * Pictorially: * * |<----------------- NOMINAL BIT TIME ----------------->| * |<- SYNC_SEG ->|<------ BS1 ------>|<------ BS2 ------>| * |<---- Tq ---->|<----- Tbs1 ------>|<----- Tbs2 ------>| * * Where * Tbs1 is the duration of the BS1 segment * Tbs2 is the duration of the BS2 segment * Tq is the "Time Quantum" * * Relationships: * * baud = 1 / bit_time * bit_time = Tq + Tbs1 + Tbs2 * Tbs1 = Tq * ts1 * Tbs2 = Tq * ts2 * Tq = brp * Tcan * * Where: * Tcan is the period of the APB clock * * Input Parameters: * priv - A reference to the CAN block status * * Returned Value: * Zero on success; a negated errno on failure * ****************************************************************************/ static int sja1000_baud_rate(struct sja1000_dev_s *priv, int rate, int clock, int sjw, int sampl_pt, int flags) { struct sja1000_config_s *config = priv->config; const struct can_bittiming_const_s *timing = config->bittiming_const; int best_error = 1000000000; int error; int best_tseg = 0; int best_brp = 0; int best_rate = 0; int brp = 0; int tseg = 0; int tseg1 = 0; int tseg2 = 0; uint32_t timing0; uint32_t timing1; /* tseg even = round down, odd = round up */ for (tseg = (0 + 0 + 2) * 2; tseg <= (timing->tseg2_max + timing->tseg1_max + 2) * 2 + 1; tseg++) { brp = clock / ((1 + tseg / 2) * rate) + tseg % 2; if (brp == 0 || brp > 64) { continue; } error = rate - clock / (brp * (1 + tseg / 2)); if (error < 0) { error = -error; } if (error <= best_error) { best_error = error; best_tseg = tseg / 2; best_brp = brp; best_rate = clock / (brp * (1 + tseg / 2)); } } if (best_error && (rate / best_error < 10)) { canerr( "baud rate %d is not possible with %d Hz clock\n", rate, clock); canerr("%d bps. brp=%d, best_tseg=%d, tseg1=%d, tseg2=%d\n", best_rate, best_brp, best_tseg, tseg1, tseg2); return -EINVAL; } tseg2 = best_tseg - (sampl_pt * (best_tseg + 1)) / 100 + 1; if (tseg2 < 0) { tseg2 = 0; } if (tseg2 > timing->tseg2_max) { tseg2 = timing->tseg2_max; } tseg1 = best_tseg - tseg2; if (tseg1 > timing->tseg1_max) { tseg1 = timing->tseg1_max; tseg2 = best_tseg - tseg1; } caninfo("Setting baud rate. TS1: %d TS2: %d BRP: %d\n", tseg1, tseg2, best_brp); /* Configure bit timing */ timing0 = ((best_brp - 1) / 2) & SJA1000_BAUD_PRESC_M; timing0 |= ((sjw - 1) << SJA1000_SYNC_JUMP_WIDTH_S) & SJA1000_SYNC_JUMP_WIDTH_M; timing1 = (tseg1 - 1) & SJA1000_TIME_SEG1_M; timing1 |= ((tseg2 - 1) << SJA1000_TIME_SEG2_S) & SJA1000_TIME_SEG2_M; if (config->triple_sample) { /* The bus is sampled 3 times (recommended for low to medium speed * buses to spikes on the bus-line). */ timing1 |= (config->triple_sample << SJA1000_TIME_SAMP_S) & SJA1000_TIME_SAMP_M; } cantrace("Writing to BTR0, BTR1: timing0: 0x%" PRIx32 " timing1: " "0x%" PRIx32 "\n", timing0, timing1); sja1000_putreg(priv, SJA1000_BUS_TIMING_1_REG, timing1); sja1000_putreg(priv, SJA1000_BUS_TIMING_0_REG, timing0); #ifdef CONFIG_CANBUS_REGDEBUG timing1 = sja1000_getreg(priv, SJA1000_BUS_TIMING_1_REG); timing0 = sja1000_getreg(priv, SJA1000_BUS_TIMING_0_REG); caninfo("Read-verify: timing0: 0x%" PRIx32 " timing1: 0x%" PRIx32 "\n", timing0, timing1); #endif /* CONFIG_CANBUS_REGDEBUG */ return OK; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: sja1000_instantiate * * Description: * Initialize the selected SJA1000 CAN Bus Controller * * Input Parameters: * priv - An instance of the "lower half" CAN driver state structure. * * Returned Value: * Valid CAN device structure reference on success; a NULL on failure * ****************************************************************************/ FAR struct can_dev_s *sja1000_instantiate(FAR struct sja1000_dev_s *priv) { struct sja1000_config_s *config = priv->config; FAR struct can_dev_s *dev; irqstate_t flags; DEBUGASSERT(dev); DEBUGASSERT(priv); DEBUGASSERT(config); cantrace("Starting sja1000_instantiate()!\n"); /* Allocate a CAN Device structure */ dev = kmm_zalloc(sizeof(struct can_dev_s)); if (dev == NULL) { canerr("ERROR: Failed to allocate instance of can_dev_s!\n"); return NULL; } #ifdef CONFIG_ARCH_HAVE_MULTICPU flags = spin_lock_irqsave(&priv->lock); #else flags = enter_critical_section(); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ #ifdef CONFIG_ARCH_HAVE_MULTICPU priv->lock = SP_UNLOCKED; #endif /* CONFIG_ARCH_HAVE_MULTICPU */ dev->cd_ops = &g_sja1000ops; dev->cd_priv = (FAR void *)priv; #ifdef CONFIG_ARCH_HAVE_MULTICPU spin_unlock_irqrestore(&priv->lock, flags); #else leave_critical_section(flags); #endif /* CONFIG_ARCH_HAVE_MULTICPU */ /* Reset chip */ sja1000_reset(dev); return dev; } #endif /* CONFIG_CAN_SJA1000 */