# # For a description of the syntax of this configuration file, # see the file kconfig-language.txt in the NuttX tools repository. # comment "Tiva/Stellaris Configuration Options" choice prompt "Tiva/Stellaris Chip Selection" default ARCH_CHIP_LM3S6965 depends on ARCH_CHIP_LM || ARCH_CHIP_TIVA || ARCH_CHIP_SIMPLELINK config ARCH_CHIP_LM3S6918 bool "LM3S6918" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_I2C1 select TIVA_HAVE_SSI1 select TIVA_HAVE_TIMER3 select TIVA_HAVE_ETHERNET config ARCH_CHIP_LM3S9B92 bool "LM3S9B92" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_UART3 select TIVA_HAVE_I2C1 select TIVA_HAVE_SSI1 select TIVA_HAVE_TIMER3 select TIVA_HAVE_ETHERNET select TIVA_HAVE_GPIOH_IRQS config ARCH_CHIP_LM3S9B96 bool "LM3S9B96" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_UART3 select TIVA_HAVE_I2C1 select TIVA_HAVE_SSI1 select TIVA_HAVE_TIMER3 select TIVA_HAVE_ETHERNET select TIVA_HAVE_GPIOH_IRQS config ARCH_CHIP_LM3S6432 bool "LM3S6432" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_ETHERNET config ARCH_CHIP_LM3S6965 bool "LM3S6965" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_UART3 select TIVA_HAVE_I2C1 select TIVA_HAVE_TIMER3 select TIVA_HAVE_ETHERNET select TIVA_HAVE_GPIOH_IRQS config ARCH_CHIP_LM3S8962 bool "LM3S8962" depends on ARCH_CHIP_LM select ARCH_CORTEXM3 select ARCH_CHIP_LM3S select TIVA_HAVE_UART3 select TIVA_HAVE_I2C1 select TIVA_HAVE_TIMER3 select TIVA_HAVE_TIMER4 select TIVA_HAVE_TIMER5 select TIVA_HAVE_ETHERNET select TIVA_HAVE_GPIOH_IRQS config ARCH_CHIP_LM4F120 bool "LM4F120" depends on ARCH_CHIP_LM select ARCH_CORTEXM4 select ARCH_CHIP_LM4F select ARCH_HAVE_FPU config ARCH_CHIP_TM4C123GH6ZRB bool "TM4C123GH6ZRB" depends on ARCH_CHIP_TIVA select ARCH_CHIP_TM4C select ARCH_CHIP_TM4C123 select TIVA_HAVE_GPIOP_IRQS select TIVA_HAVE_GPIOQ_IRQS select TIVA_HAVE_I2C4 select TIVA_HAVE_I2C5 config ARCH_CHIP_TM4C123GH6PMI bool "TM4C123GH6PMI" depends on ARCH_CHIP_TIVA select ARCH_CHIP_TM4C select ARCH_CHIP_TM4C123 select TIVA_HAVE_GPIOA_IRQS select TIVA_HAVE_GPIOB_IRQS select TIVA_HAVE_GPIOC_IRQS select TIVA_HAVE_GPIOD_IRQS select TIVA_HAVE_GPIOE_IRQS select TIVA_HAVE_GPIOF_IRQS select TIVA_HAVE_ADC0 select TIVA_HAVE_ADC1 config ARCH_CHIP_TM4C1294NC bool "TM4C1294NC" depends on ARCH_CHIP_TIVA select ARCH_CHIP_TM4C select ARCH_CHIP_TM4C129 select TIVA_HAVE_ETHERNET select TIVA_HAVE_EEPROM config ARCH_CHIP_TM4C129XNC bool "TM4C129XNC" depends on ARCH_CHIP_TIVA select ARCH_CHIP_TM4C select ARCH_CHIP_TM4C129 select TIVA_HAVE_ETHERNET config ARCH_CHIP_CC1310 bool "CC1310 SimpleLink" depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL select ARCH_CHIP_CC13X0 config ARCH_CHIP_CC1312R1 bool "CC1312R1 SimpleLink" depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL select ARCH_CHIP_CC13X2 config ARCH_CHIP_CC1352R1 bool "CC1352R1 SimpleLink" depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL select ARCH_CHIP_CC13X2 endchoice # Chip versions choice prompt "CC13xx Chip Version" default ARCH_CHIP_CC13XX_V1 depends on ARCH_CHIP_CC13X0 || ARCH_CHIP_CC13X2 config ARCH_CHIP_CC13XX_V1 bool "Version 1" depends on ARCH_CHIP_CC13X2 config ARCH_CHIP_CC13XX_V2 bool "Version 2" endchoice # CC13x2 Chip Version # Chip families config ARCH_CHIP_LM3S bool select TIVA_HAVE_GPIOA_IRQS select TIVA_HAVE_GPIOB_IRQS select TIVA_HAVE_GPIOC_IRQS select TIVA_HAVE_GPIOD_IRQS select TIVA_HAVE_GPIOE_IRQS select TIVA_HAVE_GPIOF_IRQS select TIVA_HAVE_GPIOG_IRQS select TIVA_HAVE_SSI0 select TIVA_HAVE_UART1 select TIVA_HAVE_UART2 select TIVA_HAVE_UART3 config ARCH_CHIP_LM4F bool select TIVA_HAVE_GPIOA_IRQS select TIVA_HAVE_GPIOB_IRQS select TIVA_HAVE_GPIOC_IRQS select TIVA_HAVE_GPIOD_IRQS select TIVA_HAVE_GPIOE_IRQS select TIVA_HAVE_GPIOF_IRQS select TIVA_HAVE_GPIOG_IRQS select TIVA_HAVE_GPIOH_IRQS select TIVA_HAVE_I2C1 select TIVA_HAVE_I2C2 select TIVA_HAVE_I2C3 select TIVA_HAVE_UART1 select TIVA_HAVE_UART2 select TIVA_HAVE_UART3 select TIVA_HAVE_UART4 select TIVA_HAVE_UART5 select TIVA_HAVE_UART6 select TIVA_HAVE_UART7 select TIVA_HAVE_SSI0 select TIVA_HAVE_SSI1 select TIVA_HAVE_SSI2 select TIVA_HAVE_SSI3 select TIVA_HAVE_TIMER3 select TIVA_HAVE_TIMER4 select TIVA_HAVE_TIMER5 config ARCH_CHIP_TM4C123 bool config ARCH_CHIP_TM4C129 bool select TIVA_HAVE_GPIOP_IRQS select TIVA_HAVE_GPIOQ_IRQS select TIVA_HAVE_I2C4 select TIVA_HAVE_I2C5 select TIVA_HAVE_I2C6 select TIVA_HAVE_I2C7 select TIVA_HAVE_I2C8 select TIVA_HAVE_I2C9 select TIVA_HAVE_TIMER6 select TIVA_HAVE_TIMER7 select TIVA_HAVE_UART1 select TIVA_HAVE_UART2 select TIVA_HAVE_UART3 config ARCH_CHIP_TM4C bool select ARCH_CORTEXM4 select ARCH_HAVE_FPU select TIVA_HAVE_ADC0 select TIVA_HAVE_ADC1 select TIVA_HAVE_GPIOP_IRQS select TIVA_HAVE_I2C1 select TIVA_HAVE_I2C2 select TIVA_HAVE_I2C3 select TIVA_HAVE_SSI0 select TIVA_HAVE_SSI1 select TIVA_HAVE_SSI2 select TIVA_HAVE_SSI3 select TIVA_HAVE_TIMER0 select TIVA_HAVE_TIMER1 select TIVA_HAVE_TIMER2 select TIVA_HAVE_TIMER3 select TIVA_HAVE_TIMER4 select TIVA_HAVE_TIMER5 select TIVA_HAVE_UART1 select TIVA_HAVE_UART2 select TIVA_HAVE_UART3 select TIVA_HAVE_UART4 select TIVA_HAVE_UART5 select TIVA_HAVE_UART6 select TIVA_HAVE_UART7 config ARCH_CHIP_CC13X0 bool select ARCH_CORTEXM3 select TIVA_HAVE_ADC0 select TIVA_HAVE_SSI0 select TIVA_HAVE_SSI1 select TIVA_HAVE_TIMER0 select TIVA_HAVE_TIMER1 select TIVA_HAVE_TIMER2 select TIVA_HAVE_TIMER3 config ARCH_CHIP_CC13X2 bool select ARCH_CORTEXM4 select ARCH_HAVE_FPU select TIVA_HAVE_ADC0 select TIVA_HAVE_I2C1 select TIVA_HAVE_SSI0 select TIVA_HAVE_SSI1 select TIVA_HAVE_TIMER0 select TIVA_HAVE_TIMER1 select TIVA_HAVE_TIMER2 select TIVA_HAVE_TIMER3 select TIVA_HAVE_UART1 config LM_REVA2 bool "Rev A2" default n depends on ARCH_CHIP_LM ---help--- Some early silicon returned an increase LDO voltage or 2.75V to work around a PLL bug menu "Tiva/Stellaris Peripheral Support" # MCU capabilities config TIVA_ADC bool default n config TIVA_HAVE_ADC0 bool default n config TIVA_HAVE_ADC1 bool default n config TIVA_I2C bool default n config TIVA_HAVE_I2C1 bool default n config TIVA_HAVE_I2C2 bool default n config TIVA_HAVE_I2C3 bool default n config TIVA_HAVE_I2C4 bool default n config TIVA_HAVE_I2C5 bool default n config TIVA_HAVE_I2C6 bool default n config TIVA_HAVE_I2C7 bool default n config TIVA_HAVE_I2C8 bool default n config TIVA_HAVE_I2C9 bool default n config TIVA_HAVE_UART1 bool default n config TIVA_HAVE_UART2 bool default n config TIVA_HAVE_UART3 bool default n config TIVA_HAVE_UART4 bool default n config TIVA_HAVE_UART5 bool default n config TIVA_HAVE_UART6 bool default n config TIVA_HAVE_UART7 bool default n config TIVA_HAVE_SSI0 bool default n config TIVA_HAVE_SSI1 bool default n config TIVA_HAVE_SSI2 bool default n config TIVA_HAVE_SSI3 bool default n config TIVA_HAVE_EEPROM bool default n config TIVA_HAVE_ETHERNET bool default n config TIVA_HAVE_TIMER0 bool default n config TIVA_HAVE_TIMER1 bool default n config TIVA_HAVE_TIMER2 bool default n config TIVA_HAVE_TIMER3 bool default n config TIVA_HAVE_TIMER4 bool default n config TIVA_HAVE_TIMER5 bool default n config TIVA_HAVE_TIMER6 bool default n config TIVA_HAVE_TIMER7 bool default n # Driver selections config TIVA_SSI bool default n config TIVA_TIMER bool default n # Peripheral Selections config TIVA_ADC0 bool "ADC0" default n select TIVA_ADC config TIVA_ADC1 bool "ADC1" default n depends on TIVA_HAVE_ADC0 select TIVA_ADC config TIVA_I2C0 bool "I2C0" default n select TIVA_I2C config TIVA_I2C1 bool "I2C1" default n select TIVA_I2C config TIVA_I2C2 bool "I2C2" default n depends on TIVA_HAVE_I2C2 select TIVA_I2C config TIVA_I2C3 bool "I2C3" default n depends on TIVA_HAVE_I2C3 select TIVA_I2C config TIVA_I2C4 bool "I2C4" default n depends on TIVA_HAVE_I2C4 select TIVA_I2C config TIVA_I2C5 bool "I2C5" default n depends on TIVA_HAVE_I2C5 select TIVA_I2C config TIVA_I2C6 bool "I2C6" default n depends on TIVA_HAVE_I2C6 select TIVA_I2C config TIVA_I2C7 bool "I2C7" default n depends on TIVA_HAVE_I2C7 select TIVA_I2C config TIVA_I2C8 bool "I2C8" default n depends on TIVA_HAVE_I2C8 select TIVA_I2C config TIVA_I2C9 bool "I2C9" default n depends on TIVA_HAVE_I2C9 select TIVA_I2C config TIVA_HCIUART bool default n choice prompt "UART0 Driver Configuration" default TIVA_UART0_NONE config TIVA_UART0_NONE bool "Not selected" config TIVA_UART0 bool "Standard serial driver" select UART0_SERIALDRIVER config TIVA_UART0_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART0 Driver Configuration if TIVA_UART0_HCIUART config TIVA_HCIUART0_RXBUFSIZE int "HCI UART0 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART0_TXBUFSIZE int "HCI UART0 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART0_BAUD int "HCI UART0 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART0_HCIUART choice prompt "UART1 Driver Configuration" default TIVA_UART1_NONE config TIVA_UART1_NONE bool "Not selected" config TIVA_UART1 bool "Standard serial driver" select UART1_SERIALDRIVER config TIVA_UART1_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART1 Driver Configuration if TIVA_UART1_HCIUART config TIVA_HCIUART1_RXBUFSIZE int "HCI UART1 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART1_TXBUFSIZE int "HCI UART1 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART1_BAUD int "HCI UART1 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART1_HCIUART choice prompt "UART2 Driver Configuration" default TIVA_UART2_NONE config TIVA_UART2_NONE bool "Not selected" config TIVA_UART2 bool "Standard serial driver" select UART2_SERIALDRIVER config TIVA_UART2_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART2 Driver Configuration if TIVA_UART2_HCIUART config TIVA_HCIUART2_RXBUFSIZE int "HCI UART2 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART2_TXBUFSIZE int "HCI UART2 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART2_BAUD int "HCI UART2 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART2_HCIUART choice prompt "UART3 Driver Configuration" default TIVA_UART3_NONE config TIVA_UART3_NONE bool "Not selected" config TIVA_UART3 bool "Standard serial driver" select UART3_SERIALDRIVER config TIVA_UART3_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART3 Driver Configuration if TIVA_UART3_HCIUART config TIVA_HCIUART3_RXBUFSIZE int "HCI UART3 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART3_TXBUFSIZE int "HCI UART3 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART3_BAUD int "HCI UART3 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART3_HCIUART choice prompt "UART4 Driver Configuration" default TIVA_UART4_NONE config TIVA_UART4_NONE bool "Not selected" config TIVA_UART4 bool "Standard serial driver" select UART4_SERIALDRIVER config TIVA_UART4_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART4 Driver Configuration if TIVA_UART4_HCIUART config TIVA_HCIUART4_RXBUFSIZE int "HCI UART4 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART4_TXBUFSIZE int "HCI UART4 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART4_BAUD int "HCI UART4 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART4_HCIUART choice prompt "UART5 Driver Configuration" default TIVA_UART5_NONE config TIVA_UART5_NONE bool "Not selected" config TIVA_UART5 bool "Standard serial driver" select UART5_SERIALDRIVER config TIVA_UART5_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART5 Driver Configuration if TIVA_UART5_HCIUART config TIVA_HCIUART5_RXBUFSIZE int "HCI UART5 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART5_TXBUFSIZE int "HCI UART5 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART5_BAUD int "HCI UART5 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART5_HCIUART choice prompt "UART6 Driver Configuration" default TIVA_UART6_NONE config TIVA_UART6_NONE bool "Not selected" config TIVA_UART6 bool "Standard serial driver" select UART6_SERIALDRIVER config TIVA_UART6_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART6 Driver Configuration if TIVA_UART6_HCIUART config TIVA_HCIUART6_RXBUFSIZE int "HCI UART6 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART6_TXBUFSIZE int "HCI UART6 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART6_BAUD int "HCI UART6 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART6_HCIUART choice prompt "UART7 Driver Configuration" default TIVA_UART7_NONE config TIVA_UART7_NONE bool "Not selected" config TIVA_UART7 bool "Standard serial driver" select UART7_SERIALDRIVER config TIVA_UART7_HCIUART bool "Bluetooth HCI-UART" select TIVA_HCIUART depends on WIRELESS_BLUETOOTH endchoice # UART7 Driver Configuration if TIVA_UART7_HCIUART config TIVA_HCIUART7_RXBUFSIZE int "HCI UART7 Rx buffer size" default 80 ---help--- Characters are buffered as they are received. This specifies the size of the receive buffer. Ideally this should be at least the size of the largest frame that can be received config TIVA_HCIUART7_TXBUFSIZE int "HCI UART7 Transmit buffer size" default 80 ---help--- Characters are buffered before being sent. This specifies the size of the transmit buffer. Ideally this should be at least the size of the largest frame that can be sent config TIVA_HCIUART7_BAUD int "HCI UART7 initial BAUD rate" default 115200 ---help--- The configured initial BAUD of the HCI UART used during bringup. In most cases this initial rate can be increased by the upper half HCI UART driver using vendor-specifi HCI UART commands. endif # TIVA_UART7_HCIUART menu "HCI UART Driver Configuration" depends on TIVA_HCIUART config TIVA_HCIUART_SW_RXFLOW bool "Use Software UART RTS flow control" default n ---help--- Enable UART RTS flow control using Software. config TIVA_HCIUART_SW_TXFLOW bool "Use Software UART CTS flow control" default n ---help--- Enable UART CTS flow control using Software. endmenu # HCI UART Driver Configuration config TIVA_SSI0 bool "SSI0" default n depends on TIVA_HAVE_SSI0 select TIVA_SSI config TIVA_SSI1 bool "SSI1" default n depends on TIVA_HAVE_SSI1 select TIVA_SSI config TIVA_SSI2 bool "SSI2" default n depends on TIVA_HAVE_SSI2 select TIVA_SSI config TIVA_SSI3 bool "SSI3" default n depends on TIVA_HAVE_SSI3 select TIVA_SSI config TIVA_TIMER0 bool "16-/32-bit Timer 0" default n depends on TIVA_HAVE_TIMER0 select TIVA_TIMER config TIVA_TIMER1 bool "16-/32-bit Timer 1" default n depends on TIVA_HAVE_TIMER1 select TIVA_TIMER config TIVA_TIMER2 bool "16-/32-bit Timer 2" default n depends on TIVA_HAVE_TIMER2 select TIVA_TIMER config TIVA_TIMER3 bool "16-/32-bit Timer 3" default n depends on TIVA_HAVE_TIMER3 select TIVA_TIMER config TIVA_TIMER4 bool "16-/32-bit Timer 4" default n depends on TIVA_HAVE_TIMER4 select TIVA_TIMER config TIVA_TIMER5 bool "16-/32-bit Timer 5" default n depends on TIVA_HAVE_TIMER5 select TIVA_TIMER config TIVA_TIMER6 bool "16-/32-bit Timer 6" default n depends on TIVA_HAVE_TIMER6 select TIVA_TIMER config TIVA_TIMER7 bool "16-/32-bit Timer 7" default n depends on TIVA_HAVE_TIMER7 select TIVA_TIMER config TIVA_ETHERNET bool "Ethernet" default n depends on TIVA_HAVE_ETHERNET select NETDEVICES select ARCH_HAVE_NETDEV_STATISTICS if ARCH_CHIP_LM3S || ARCH_CHIP_LM4F ---help--- This must be set (along with NET) to build the Stellaris Ethernet driver. config TIVA_FLASH bool "Internal FLASH driver" default n ---help--- Enable MTD driver support for internal FLASH. config TIVA_EEPROM bool "Internal EEPROM driver" default n depends on TIVA_HAVE_EEPROM && EXPERIMENTAL ---help--- Enable MTD driver support for internal EEPROM. endmenu config TIVA_RAMVBAR bool "Set VBAR" default n ---help--- Set the ARM VBAR register to position interrupt vectors at the beginning of RAM (vs the beginning of FLASH). The beginning of RAM is that address defined by CONFIG_RAM_START. menu "Enable GPIO Interrupts" config TIVA_GPIO_IRQS bool default n config TIVA_HAVE_GPIOA_IRQS bool default n config TIVA_HAVE_GPIOB_IRQS bool default n config TIVA_HAVE_GPIOC_IRQS bool default n config TIVA_HAVE_GPIOD_IRQS bool default n config TIVA_HAVE_GPIOE_IRQS bool default n config TIVA_HAVE_GPIOF_IRQS bool default n config TIVA_HAVE_GPIOG_IRQS bool default n config TIVA_HAVE_GPIOH_IRQS bool default n config TIVA_HAVE_GPIOJ_IRQS bool default n config TIVA_HAVE_GPIOK_IRQS bool default n config TIVA_HAVE_GPIOL_IRQS bool default n config TIVA_HAVE_GPIOM_IRQS bool default n config TIVA_HAVE_GPION_IRQS bool default n config TIVA_HAVE_GPIOP_IRQS bool default n config TIVA_HAVE_GPIOQ_IRQS bool default n config TIVA_HAVE_GPIOR_IRQS bool default n config TIVA_HAVE_GPIOS_IRQS bool default n config TIVA_HAVE_GPIOT_IRQS bool default n config TIVA_GPIOA_IRQS bool "Enable GPIOA IRQs" default n depends on TIVA_HAVE_GPIOA_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOB_IRQS bool "Enable GPIOB IRQs" default n depends on TIVA_HAVE_GPIOB_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOC_IRQS bool "Enable GPIOC IRQs" default n depends on TIVA_HAVE_GPIOC_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOD_IRQS bool "Enable GPIOD IRQs" default n depends on TIVA_HAVE_GPIOD_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOE_IRQS bool "Enable GPIOE IRQs" default n depends on TIVA_HAVE_GPIOE_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOF_IRQS bool "Enable GPIOF IRQs" default n depends on TIVA_HAVE_GPIOF_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOG_IRQS bool "Enable GPIOG IRQs" default n depends on TIVA_HAVE_GPIOG_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOH_IRQS bool "Enable GPIOH IRQs" default n depends on TIVA_HAVE_GPIOH_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOJ_IRQS bool "Enable GPIOJ IRQs" default n depends on TIVA_HAVE_GPIOJ_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOK_IRQS bool "Enable GPIOK IRQs" default n depends on TIVA_HAVE_GPIOK_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOL_IRQS bool "Enable GPIOL IRQs" default n depends on TIVA_HAVE_GPIOL_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOM_IRQS bool "Enable GPIOM IRQs" default n depends on TIVA_HAVE_GPIOM_IRQS select TIVA_GPIO_IRQS config TIVA_GPION_IRQS bool "Enable GPION IRQs" default n depends on TIVA_HAVE_GPION_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOP_IRQS bool "Enable GPIOP IRQs" default n depends on TIVA_HAVE_GPIOP_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOQ_IRQS bool "Enable GPIOQ IRQs" default n depends on TIVA_HAVE_GPIOQ_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOR_IRQS bool "Enable GPIOR IRQs" default n depends on TIVA_HAVE_GPIOR_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOS_IRQS bool "Enable GPIOS IRQs" default n depends on TIVA_HAVE_GPIOS_IRQS select TIVA_GPIO_IRQS config TIVA_GPIOT_IRQS bool "Enable GPIOT IRQs" default n depends on TIVA_HAVE_GPIOT_IRQS select TIVA_GPIO_IRQS endmenu if TIVA_I2C menu "I2C Configuration" config TIVA_I2C_DYNTIMEO bool "Use dynamic timeouts" default n if TIVA_I2C_DYNTIMEO config TIVA_I2C_DYNTIMEO_USECPERBYTE int "Timeout Microseconds per Byte" default 500 config TIVA_I2C_DYNTIMEO_STARTSTOP int "Timeout for Start/Stop (Milliseconds)" default 1000 endif # TIVA_I2C_DYNTIMEO config TIVA_I2C_TIMEOSEC int "Timeout seconds" default 0 if !TIVA_I2C_DYNTIMEO config TIVA_I2C_TIMEOMS int "Timeout Milliseconds" default 500 depends on !TIVA_I2C_DYNTIMEO config TIVA_I2C_TIMEOTICKS int "Timeout for Done and Stop (ticks)" default 500 depends on !TIVA_I2C_DYNTIMEO endif # !TIVA_I2C_DYNTIMEO config TIVA_I2C_HIGHSPEED bool "High speed support" default n depends on ARCH_CHIP_TM4C && EXPERIMENTAL ---help--- Enable support for high speed I2C transfers. Only partially implemented and completely untested. config TIVA_I2C_REGDEBUG bool "Register level debug" default n depends on DEBUG_I2C_INFO ---help--- Enables extremely detailed register access debug output. endmenu # I2C Configuration endif # TIVA_I2C if TIVA_TIMER menu "Timer Configuration" config TIVA_TIMER_32BIT bool "32-bit timer support" default n if TIVA_TIMER_32BIT config TIVA_TIMER32_PERIODIC bool "32-bit one-shot/periodic timer support" default n config TIVA_TIMER32_RTC bool "32-bit RTC (needs 32.768-KHz input)" default n endif # TIVA_TIMER_32BIT config TIVA_TIMER_16BIT bool "16-bit timer support" default n if TIVA_TIMER_16BIT config TIVA_TIMER16_PERIODIC bool "16-bit one-shot/periodic timer support" default n config TIVA_TIMER16_EDGECOUNT bool "16-bit input edge-count capture support" default n depends on EXPERIMENTAL config TIVA_TIMER16_TIMECAP bool "16-bit input time capture support" default n depends on EXPERIMENTAL config TIVA_TIMER16_PWM bool "16-bit PWM output support" default n depends on EXPERIMENTAL endif # TIVA_TIMER_16BIT config TIVA_TIMER_REGDEBUG bool "Register level debug" default n depends on DEBUG_TIMER_INFO ---help--- Enables extremely detailed register access debug output. endmenu # Tiva Timer Configuration endif # TIVA_TIMER if TIVA_ADC menu "ADC Configuration" config TIVA_ADC_REGDEBUG bool "Register level debug" default n depends on DEBUG_ANALOG_INFO ---help--- Enables extremely detailed register access debug output. endmenu # Tiva ADC Configuration endif # TIVA_ADC if TIVA_ETHERNET menu "Stellaris Ethernet Configuration" depends on ARCH_CHIP_LM3S config TIVA_ETHLEDS bool "Ethernet LEDs" default n ---help--- Enable to use Ethernet LEDs on the board. config TIVA_ETHHDUPLEX bool "Force Half Duplex" default n ---help--- Set to force half duplex operation config TIVA_ETHNOAUTOCRC bool "Disable auto-CRC" default n ---help--- Set to suppress auto-CRC generation config TIVA_ETHNOPAD bool "Disable Tx Padding" default n ---help--- Set to suppress Tx padding config TIVA_MULTICAST bool "Enable Multicast" default n ---help--- Set to enable multicast frames config TIVA_PROMISCUOUS bool "Enable Promiscuous Mode" default n ---help--- Set to enable promiscuous mode config TIVA_TIMESTAMP bool "Enable Timestamping" default n config TIVA_BADCRC bool "Enable Bad CRC Rejection" default n ---help--- Set to enable bad CRC rejection. config TIVA_DUMPPACKET bool "Dump Packets" default n ---help--- Dump each packet received/sent to the console. endmenu # Stellaris Ethernet Configuration menu "Ethernet Configuration" depends on ARCH_CHIP_TM4C choice prompt "PHY selection" default TIVA_PHY_INTERNAL config TIVA_PHY_INTERNAL bool "Internal PHY" ---help--- Use the built-in, internal Tiva PHY config TIVA_PHY_MII bool "External MII interface" depends on EXPERIMENTAL ---help--- Support external PHY MII interface. config TIVA_PHY_RMII bool "External RMII interface" depends on EXPERIMENTAL ---help--- Support external PHY RMII interface. endchoice # PHY selection config TIVA_AUTONEG bool "Use autonegotiation" default y ---help--- Use PHY autonegotiation to determine speed and mode if !TIVA_PHY_INTERNAL config TIVA_PHYADDR int "PHY address" default 1 ---help--- The 5-bit address of the PHY on the board. Default: 1 if !TIVA_AUTONEG config TIVA_ETHFD bool "Full duplex" default n ---help--- If TIVA_AUTONEG is not defined, then this may be defined to select full duplex mode. Default: half-duplex config TIVA_ETH100MBPS bool "100 Mbps" default n ---help--- If TIVA_AUTONEG is not defined, then this may be defined to select 100 MBps speed. Default: 10 Mbps endif # !TIVA_AUTONEG if TIVA_AUTONEG config TIVA_PHYSR int "PHY Status Register Address (decimal)" ---help--- This must be provided if TIVA_AUTONEG is defined. The PHY status register address may diff from PHY to PHY. This configuration sets the address of the PHY status register. config TIVA_PHYSR_ALTCONFIG bool "PHY Status Alternate Bit Layout" default n ---help--- Different PHYs present speed and mode information in different ways. Some will present separate information for speed and mode (this is the default). Those PHYs, for example, may provide a 10/100 Mbps indication and a separate full/half duplex indication. This options selects an alternative representation where speed and mode information are combined. This might mean, for example, separate bits for 10HD, 100HD, 10FD and 100FD. if !TIVA_PHYSR_ALTCONFIG config TIVA_PHYSR_SPEED hex "PHY Speed Mask" ---help--- This must be provided if TIVA_AUTONEG is defined. This provides bit mask for isolating the 10 or 100MBps speed indication. config TIVA_PHYSR_100MBPS hex "PHY 100Mbps Speed Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This provides the value of the speed bit(s) indicating 100MBps speed. config TIVA_PHYSR_MODE hex "PHY Mode Mask" ---help--- This must be provided if TIVA_AUTONEG is defined. This provide bit mask for isolating the full or half duplex mode bits. config TIVA_PHYSR_FULLDUPLEX hex "PHY Full Duplex Mode Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This provides the value of the mode bits indicating full duplex mode. endif # !TIVA_PHYSR_ALTCONFIG if TIVA_PHYSR_ALTCONFIG config TIVA_PHYSR_ALTMODE hex "PHY Mode Mask" ---help--- This must be provided if TIVA_AUTONEG is defined. This provide bit mask for isolating the speed and full/half duplex mode bits. config TIVA_PHYSR_10HD hex "10MBase-T Half Duplex Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This is the value under the bit mask that represents the 10Mbps, half duplex setting. config TIVA_PHYSR_100HD hex "100Base-T Half Duplex Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This is the value under the bit mask that represents the 100Mbps, half duplex setting. config TIVA_PHYSR_10FD hex "10Base-T Full Duplex Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This is the value under the bit mask that represents the 10Mbps, full duplex setting. config TIVA_PHYSR_100FD hex "100Base-T Full Duplex Value" ---help--- This must be provided if TIVA_AUTONEG is defined. This is the value under the bit mask that represents the 100Mbps, full duplex setting. endif # TIVA_PHYSR_ALTCONFIG endif # TIVA_AUTONEG endif # !TIVA_PHY_INTERNAL config TIVA_PHY_INTERRUPTS bool "PHY interrupt support" select ARCH_PHY_INTERRUPT select NETDEV_PHY_IOCTL default n ---help--- Enable logic to signal user tasks when a PHY interrupt occurs. The PHY interrupt may indicate a change in the link status such as, for example, when a cable is plugged in or unplugged. config TIVA_EMAC_NRXDESC int "Number of RX descriptors" default 8 ---help--- Number of RX DMA descriptors to use. config TIVA_EMAC_NTXDESC int "Number of TX descriptors" default 4 ---help--- Number of TX DMA descriptors to use. config TIVA_EMAC_ENHANCEDDESC bool default n config TIVA_EMAC_PTP bool "Precision Time Protocol (PTP)" default n depends on EXPERIMENTAL select TIVA_EMAC_ENHANCEDDESC ---help--- Precision Time Protocol (PTP). Not supported but some hooks are indicated with this condition. config TIVA_EMAC_HWCHECKSUM bool "Use hardware checksums" default n depends on EXPERIMENTAL ---help--- Use the hardware checksum capabilities of the Tiva chip config TIVA_ETHERNET_REGDEBUG bool "Register-Level Debug" default n depends on DEBUG_NET_INFO ---help--- Enable very low-level register access debug. Depends on CONFIG_DEBUG_FEATURES. endmenu # Tiva Ethernet Configuration config TIVA_BOARDMAC bool "Board MAC" default n ---help--- If the board-specific logic can provide a MAC address (via tiva_ethernetmac()), then this should be selected. endif # TIVA_ETHERNET if TIVA_SSI menu "Tiva/Stellaris SSI Configuration" config SSI_POLLWAIT bool "Poll Wait (No-Interrupt) Mode" default y config SSI_TXLIMIT int "Tx Limit" default 4 ---help--- Default of 4 assumes half of the 8 entry FIFO endmenu endif if TIVA_FLASH menu "Tiva/Stellaris Internal Flash Driver Configuration" config TIVA_FLASH_STARTPAGE int "First page accessible by the MTD driver" default 250 ---help--- To prevent accessing FLASH sections where code is stored. endmenu endif