/**************************************************************************** * arch/arm/src/stm32/stm32_adc.c * * Copyright (C) 2011, 2013, 2015-2017 Gregory Nutt. All rights reserved. * Copyright (C) 2015 Omni Hoverboards Inc. All rights reserved. * Authors: Gregory Nutt * Diego Sanchez * Paul Alexander Patience * Mateusz Szafoni * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in * the documentation and/or other materials provided with the * distribution. * 3. Neither the name NuttX nor the names of its contributors may be * used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************/ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "up_internal.h" #include "up_arch.h" #include "chip.h" #include "stm32.h" #include "stm32_dma.h" #include "stm32_adc.h" /* ADC "upper half" support must be enabled */ #ifdef CONFIG_STM32_ADC /* Some ADC peripheral must be enabled */ #if defined(CONFIG_STM32_ADC1) || defined(CONFIG_STM32_ADC2) || \ defined(CONFIG_STM32_ADC3) || defined(CONFIG_STM32_ADC4) /* This implementation is for the STM32 F1, F2, F3, F4 and STM32L15XX only */ #if defined(CONFIG_STM32_STM32F10XX) || defined(CONFIG_STM32_STM32F20XX) || \ defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) || \ defined(CONFIG_STM32_STM32F37XX) || defined(CONFIG_STM32_STM32F40XX) || \ defined(CONFIG_STM32_STM32L15XX) /* At the moment there is no proper implementation for timers external * trigger in STM32L15XX May be added latter */ #if defined(ADC_HAVE_TIMER) && defined(CONFIG_STM32_STM32L15XX) # warning "There is no proper implementation for TIMER TRIGGERS at the moment" #endif /* At the moment there is no proper implementation for HRTIMER external * trigger in STM32F33XX */ #if defined(ADC_HAVE_HRTIMER) && defined(CONFIG_STM32_STM32F33XX) # warning "There is no proper implementation for HRTIMER TRIGGERS at the moment" #endif /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* RCC reset ****************************************************************/ #if defined(CONFIG_STM32_STM32F10XX) # define STM32_RCC_RSTR STM32_RCC_APB2RSTR # define RCC_RSTR_ADC1RST RCC_APB2RSTR_ADC1RST # define RCC_RSTR_ADC2RST RCC_APB2RSTR_ADC2RST # define RCC_RSTR_ADC3RST RCC_APB2RSTR_ADC3RST # define RCC_RSTR_ADC4RST RCC_APB2RSTR_ADC4RST #elif defined(CONFIG_STM32_STM32F30XX) # define STM32_RCC_RSTR STM32_RCC_AHBRSTR # define RCC_RSTR_ADC1RST RCC_AHBRSTR_ADC12RST # define RCC_RSTR_ADC2RST RCC_AHBRSTR_ADC12RST # define RCC_RSTR_ADC3RST RCC_AHBRSTR_ADC34RST # define RCC_RSTR_ADC4RST RCC_AHBRSTR_ADC34RST #elif defined(CONFIG_STM32_STM32F33XX) # define STM32_RCC_RSTR STM32_RCC_AHBRSTR # define RCC_RSTR_ADC1RST RCC_AHBRSTR_ADC12RST # define RCC_RSTR_ADC2RST RCC_AHBRSTR_ADC12RST #elif defined(CONFIG_STM32_STM32F37XX) # define STM32_RCC_RSTR STM32_RCC_APB2RSTR # define RCC_RSTR_ADC1RST RCC_APB2RSTR_ADCRST #elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX) # define STM32_RCC_RSTR STM32_RCC_APB2RSTR # define RCC_RSTR_ADC1RST RCC_APB2RSTR_ADCRST # define RCC_RSTR_ADC2RST RCC_APB2RSTR_ADCRST # define RCC_RSTR_ADC3RST RCC_APB2RSTR_ADCRST # define RCC_RSTR_ADC4RST RCC_APB2RSTR_ADCRST #elif defined(CONFIG_STM32_STM32L15XX) # define STM32_RCC_RSTR STM32_RCC_APB2RSTR # define RCC_RSTR_ADC1RST RCC_APB2RSTR_ADC1RST #endif /* ADC interrupts ***********************************************************/ #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) # define STM32_ADC_DMAREG_OFFSET STM32_ADC_CFGR_OFFSET # define ADC_DMAREG_DMA ADC_CFGR_DMAEN # define STM32_ADC_EXTREG_OFFSET STM32_ADC_CFGR_OFFSET # define ADC_EXTREG_EXTSEL_MASK ADC_CFGR_EXTSEL_MASK # define ADC_EXTREG_EXTEN_MASK ADC_CFGR_EXTEN_MASK # define ADC_EXTREG_EXTEN_DEFAULT ADC_CFGR_EXTEN_RISING # define ADC_ISR_EOC ADC_INT_EOC # define ADC_IER_EOC ADC_INT_EOC # define ADC_ISR_AWD ADC_INT_AWD1 # define ADC_IER_AWD ADC_INT_AWD1 # define ADC_ISR_JEOC ADC_INT_JEOC # define ADC_IER_JEOC ADC_INT_JEOC # define ADC_ISR_OVR ADC_INT_OVR # define ADC_IER_OVR ADC_INT_OVR #else # define STM32_ADC_DMAREG_OFFSET STM32_ADC_CR2_OFFSET # define ADC_DMAREG_DMA ADC_CR2_DMA # define STM32_ADC_EXTREG_OFFSET STM32_ADC_CR2_OFFSET # define ADC_EXTREG_EXTSEL_MASK ADC_CR2_EXTSEL_MASK # define STM32_ADC_ISR_OFFSET STM32_ADC_SR_OFFSET # define STM32_ADC_IER_OFFSET STM32_ADC_CR1_OFFSET # define ADC_ISR_EOC ADC_SR_EOC # define ADC_IER_EOC ADC_CR1_EOCIE # define ADC_ISR_AWD ADC_SR_AWD # define ADC_IER_AWD ADC_CR1_AWDIE # define ADC_ISR_JEOC ADC_SR_JEOC # define ADC_IER_JEOC ADC_CR1_JEOCIE # if defined(CONFIG_STM32_STM32F10XX) || defined(CONFIG_STM32_STM32F37XX) # define ADC_EXTREG_EXTEN_MASK ADC_CR2_EXTTRIG # define ADC_EXTREG_EXTEN_NONE 0 # define ADC_EXTREG_EXTEN_DEFAULT ADC_CR2_EXTTRIG # define ADC_ISR_OVR 0 # define ADC_IER_OVR 0 # else # define ADC_EXTREG_EXTEN_MASK ADC_CR2_EXTEN_MASK # define ADC_EXTREG_EXTEN_NONE ADC_CR2_EXTEN_NONE # define ADC_EXTREG_EXTEN_DEFAULT ADC_CR2_EXTEN_RISING # define ADC_ISR_OVR ADC_SR_OVR # define ADC_IER_OVR ADC_CR1_OVRIE # endif #endif #define ADC_ISR_ALLINTS (ADC_ISR_EOC | ADC_ISR_AWD | ADC_ISR_JEOC | \ ADC_ISR_OVR) #define ADC_IER_ALLINTS (ADC_IER_EOC | ADC_IER_AWD | ADC_IER_JEOC | \ ADC_IER_OVR) /* ADC Channels/DMA ********************************************************/ /* The maximum number of channels that can be sampled. If DMA support is * not enabled, then only a single channel can be sampled. Otherwise, * data overruns would occur. */ #define ADC_MAX_CHANNELS_DMA 16 #define ADC_MAX_CHANNELS_NODMA 1 #ifdef ADC_HAVE_DMA # define ADC_MAX_SAMPLES ADC_MAX_CHANNELS_DMA #else # if defined(CONFIG_STM32_STM32F30XX) # define ADC_MAX_SAMPLES ADC_MAX_CHANNELS_DMA /* Works without DMA should sampling frequency be reduced */ # else # define ADC_MAX_SAMPLES ADC_MAX_CHANNELS_NODMA # endif #endif #if defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX) # define ADC_DMA_CONTROL_WORD (DMA_SCR_MSIZE_16BITS | \ DMA_SCR_PSIZE_16BITS | \ DMA_SCR_MINC | \ DMA_SCR_CIRC | \ DMA_SCR_DIR_P2M) #else # define ADC_DMA_CONTROL_WORD (DMA_CCR_MSIZE_16BITS | \ DMA_CCR_PSIZE_16BITS | \ DMA_CCR_MINC | \ DMA_CCR_CIRC) #endif /* DMA channels and interface values differ for the F1 and F4 families */ #if defined(CONFIG_STM32_STM32F10XX) # define ADC_SMPR_DEFAULT ADC_SMPR_55p5 # define ADC_SMPR1_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR1_SMP10_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP11_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP12_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP13_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP14_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP15_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP16_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP17_SHIFT)) # define ADC_SMPR2_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR2_SMP0_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP1_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP2_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP3_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP4_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP5_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP6_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP7_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP8_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP9_SHIFT)) #elif defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) # if defined(ADC_HAVE_DMA) || (ADC_MAX_SAMPLES == 1) # define ADC_SMPR_DEFAULT ADC_SMPR_61p5 # else /* Slow down sampling frequency */ # define ADC_SMPR_DEFAULT ADC_SMPR_601p5 # endif # define ADC_SMPR1_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR1_SMP1_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP2_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP3_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP4_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP5_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP6_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP7_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP8_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP9_SHIFT)) # define ADC_SMPR2_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR2_SMP10_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP11_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP12_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP13_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP14_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP15_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP16_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP17_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP18_SHIFT)) #elif defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F37XX) || \ defined(CONFIG_STM32_STM32F40XX) # if defined(CONFIG_STM32_STM32F37XX) # define ADC_SMPR_DEFAULT ADC_SMPR_239p5 /* TODO choose 1p5? */ # else # define ADC_SMPR_DEFAULT ADC_SMPR_112 # endif # define ADC_SMPR1_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR1_SMP10_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP11_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP12_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP13_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP14_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP15_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP16_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP17_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR1_SMP18_SHIFT)) # define ADC_SMPR2_DEFAULT ((ADC_SMPR_DEFAULT << ADC_SMPR2_SMP0_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP1_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP2_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP3_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP4_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP5_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP6_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP7_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP8_SHIFT) | \ (ADC_SMPR_DEFAULT << ADC_SMPR2_SMP9_SHIFT)) #elif defined(CONFIG_STM32_STM32L15XX) # define ADC_CHANNELS_NUMBER 32 # define ADC_SMPR_DEFAULT ADC_SMPR_384 #endif /**************************************************************************** * Private Types ****************************************************************************/ /* This structure describes the state of one ADC block */ struct stm32_dev_s { FAR const struct adc_callback_s *cb; uint8_t irq; /* Interrupt generated by this ADC block */ uint8_t nchannels; /* Number of channels */ uint8_t cchannels; /* Number of configured channels */ uint8_t intf; /* ADC interface number */ uint8_t current; /* Current ADC channel being converted */ #ifdef ADC_HAVE_DMA uint8_t dmachan; /* DMA channel needed by this ADC */ bool hasdma; /* True: This channel supports DMA */ #endif #ifdef CONFIG_STM32_STM32L15XX /* Sample time selection. These bits must be written only when ADON=0 */ uint8_t sample_rate[ADC_CHANNELS_NUMBER]; #endif #ifdef ADC_HAVE_TIMER uint8_t trigger; /* Timer trigger channel: 0=CC1, 1=CC2, 2=CC3, * 3=CC4, 4=TRGO */ #endif xcpt_t isr; /* Interrupt handler for this ADC block */ uint32_t base; /* Base address of registers unique to this ADC * block */ #ifdef ADC_HAVE_TIMER uint32_t tbase; /* Base address of timer used by this ADC block */ uint32_t extsel; /* EXTSEL value used by this ADC block */ uint32_t pclck; /* The PCLK frequency that drives this timer */ uint32_t freq; /* The desired frequency of conversions */ #endif #ifdef ADC_HAVE_DMA DMA_HANDLE dma; /* Allocated DMA channel */ /* DMA transfer buffer */ uint16_t dmabuffer[ADC_MAX_SAMPLES]; #endif /* List of selected ADC channels to sample */ uint8_t chanlist[ADC_MAX_SAMPLES]; }; /**************************************************************************** * Private Function Prototypes ****************************************************************************/ /* ADC Register access */ #if defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F30XX) || \ defined(CONFIG_STM32_STM32F33XX) || defined(CONFIG_STM32_STM32F37XX) || \ defined(CONFIG_STM32_STM32F40XX) || defined(CONFIG_STM32_STM32L15XX) static void stm32_modifyreg32(unsigned int addr, uint32_t clrbits, uint32_t setbits); #endif static uint32_t adc_getreg(FAR struct stm32_dev_s *priv, int offset); static void adc_putreg(FAR struct stm32_dev_s *priv, int offset, uint32_t value); static void adc_modifyreg(FAR struct stm32_dev_s *priv, int offset, uint32_t clrbits, uint32_t setbits); #ifdef ADC_HAVE_TIMER static uint16_t tim_getreg(FAR struct stm32_dev_s *priv, int offset); static void tim_putreg(FAR struct stm32_dev_s *priv, int offset, uint16_t value); static void tim_modifyreg(FAR struct stm32_dev_s *priv, int offset, uint16_t clrbits, uint16_t setbits); static void tim_dumpregs(FAR struct stm32_dev_s *priv, FAR const char *msg); #endif static void adc_rccreset(FAR struct stm32_dev_s *priv, bool reset); /* ADC Interrupt Handler */ static int adc_interrupt(FAR struct adc_dev_s *dev); #if defined(STM32_IRQ_ADC1) && defined(CONFIG_STM32_ADC1) static int adc1_interrupt(int irq, FAR void *context, FAR void *arg); #endif #if defined(STM32_IRQ_ADC12) && (defined(CONFIG_STM32_ADC1) || \ defined(CONFIG_STM32_ADC2)) static int adc12_interrupt(int irq, FAR void *context, FAR void *arg); #endif #if (defined(STM32_IRQ_ADC3) && defined(CONFIG_STM32_ADC3)) static int adc3_interrupt(int irq, FAR void *context, FAR void *arg); #endif #if defined(STM32_IRQ_ADC4) && defined(CONFIG_STM32_ADC4) static int adc4_interrupt(int irq, FAR void *context, FAR void *arg); #endif #if defined(STM32_IRQ_ADC) static int adc123_interrupt(int irq, FAR void *context, FAR void *arg); #endif /* ADC Driver Methods */ static int adc_bind(FAR struct adc_dev_s *dev, FAR const struct adc_callback_s *callback); static void adc_reset(FAR struct adc_dev_s *dev); static int adc_setup(FAR struct adc_dev_s *dev); static void adc_shutdown(FAR struct adc_dev_s *dev); static void adc_rxint(FAR struct adc_dev_s *dev, bool enable); static int adc_ioctl(FAR struct adc_dev_s *dev, int cmd, unsigned long arg); static void adc_enable(FAR struct stm32_dev_s *priv, bool enable); static uint32_t adc_sqrbits(FAR struct stm32_dev_s *priv, int first, int last, int offset); static int adc_set_ch(FAR struct adc_dev_s *dev, uint8_t ch); #ifdef CONFIG_STM32_STM32L15XX static void adc_power_down_idle(FAR struct stm32_dev_s *priv, bool pdi_high); static void adc_power_down_delay(FAR struct stm32_dev_s *priv, bool pdd_high); static void adc_dels_after_conversion(FAR struct stm32_dev_s *priv, uint32_t delay); static void adc_select_ch_bank(FAR struct stm32_dev_s *priv, bool chb_selected); static int adc_ioc_change_ints(FAR struct adc_dev_s *dev, int cmd, bool arg); #if STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI static void adc_enable_hsi(bool enable); static void adc_reset_hsi_disable(FAR struct adc_dev_s *dev); #endif #endif #ifdef ADC_HAVE_TIMER static void adc_timstart(FAR struct stm32_dev_s *priv, bool enable); static int adc_timinit(FAR struct stm32_dev_s *priv); #endif #ifdef ADC_HAVE_DMA static void adc_dmaconvcallback(DMA_HANDLE handle, uint8_t isr, FAR void *arg); #endif static void adc_startconv(FAR struct stm32_dev_s *priv, bool enable); /**************************************************************************** * Private Data ****************************************************************************/ /* ADC interface operations */ static const struct adc_ops_s g_adcops = { .ao_bind = adc_bind, #if defined(CONFIG_STM32_STM32L15XX) && \ (STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI) .ao_reset = adc_reset_hsi_disable, #else .ao_reset = adc_reset, #endif .ao_setup = adc_setup, .ao_shutdown = adc_shutdown, .ao_rxint = adc_rxint, .ao_ioctl = adc_ioctl, }; /* ADC1 state */ #ifdef CONFIG_STM32_ADC1 static struct stm32_dev_s g_adcpriv1 = { #if defined(STM32_IRQ_ADC1) .irq = STM32_IRQ_ADC1, .isr = adc1_interrupt, #elif defined(STM32_IRQ_ADC12) .irq = STM32_IRQ_ADC12, .isr = adc12_interrupt, #elif defined(STM32_IRQ_ADC) .irq = STM32_IRQ_ADC, .isr = adc123_interrupt, #else # error "No STM32_IRQ_ADC1 STM32_IRQ_ADC12 or STM32_IRQ_ADC defined for CONFIG_STM32_ADC1" #endif .intf = 1, .base = STM32_ADC1_BASE, #ifdef ADC1_HAVE_TIMER .trigger = CONFIG_STM32_ADC1_TIMTRIG, .tbase = ADC1_TIMER_BASE, .extsel = ADC1_EXTSEL_VALUE, .pclck = ADC1_TIMER_PCLK_FREQUENCY, .freq = CONFIG_STM32_ADC1_SAMPLE_FREQUENCY, #endif #ifdef ADC1_HAVE_DMA .dmachan = ADC1_DMA_CHAN, .hasdma = true, #endif }; static struct adc_dev_s g_adcdev1 = { .ad_ops = &g_adcops, .ad_priv = &g_adcpriv1, }; #endif /* ADC2 state */ #ifdef CONFIG_STM32_ADC2 static struct stm32_dev_s g_adcpriv2 = { #if defined(STM32_IRQ_ADC12) .irq = STM32_IRQ_ADC12, .isr = adc12_interrupt, #elif defined(STM32_IRQ_ADC) .irq = STM32_IRQ_ADC, .isr = adc123_interrupt, #else # error "No STM32_IRQ_ADC12 or STM32_IRQ_ADC defined for CONFIG_STM32_ADC2" #endif .intf = 2, .base = STM32_ADC2_BASE, #ifdef ADC2_HAVE_TIMER .trigger = CONFIG_STM32_ADC2_TIMTRIG, .tbase = ADC2_TIMER_BASE, .extsel = ADC2_EXTSEL_VALUE, .pclck = ADC2_TIMER_PCLK_FREQUENCY, .freq = CONFIG_STM32_ADC2_SAMPLE_FREQUENCY, #endif #ifdef ADC2_HAVE_DMA .dmachan = ADC2_DMA_CHAN, .hasdma = true, #endif }; static struct adc_dev_s g_adcdev2 = { .ad_ops = &g_adcops, .ad_priv = &g_adcpriv2, }; #endif /* ADC3 state */ #ifdef CONFIG_STM32_ADC3 static struct stm32_dev_s g_adcpriv3 = { #if defined(STM32_IRQ_ADC3) .irq = STM32_IRQ_ADC3, .isr = adc3_interrupt, #elif defined(STM32_IRQ_ADC) .irq = STM32_IRQ_ADC, .isr = adc123_interrupt, #else # error "No STM32_IRQ_ADC3 or STM32_IRQ_ADC defined for CONFIG_STM32_ADC3" #endif .intf = 3, .base = STM32_ADC3_BASE, #ifdef ADC3_HAVE_TIMER .trigger = CONFIG_STM32_ADC3_TIMTRIG, .tbase = ADC3_TIMER_BASE, .extsel = ADC3_EXTSEL_VALUE, .pclck = ADC3_TIMER_PCLK_FREQUENCY, .freq = CONFIG_STM32_ADC3_SAMPLE_FREQUENCY, #endif #ifdef ADC3_HAVE_DMA .dmachan = ADC3_DMA_CHAN, .hasdma = true, #endif }; static struct adc_dev_s g_adcdev3 = { .ad_ops = &g_adcops, .ad_priv = &g_adcpriv3, }; #endif /* ADC4 state */ #ifdef CONFIG_STM32_ADC4 static struct stm32_dev_s g_adcpriv4 = { .irq = STM32_IRQ_ADC4, .isr = adc4_interrupt, .intf = 4, .base = STM32_ADC4_BASE, #ifdef ADC4_HAVE_TIMER .trigger = CONFIG_STM32_ADC4_TIMTRIG, .tbase = ADC4_TIMER_BASE, .extsel = ADC4_EXTSEL_VALUE, .pclck = ADC4_TIMER_PCLK_FREQUENCY, .freq = CONFIG_STM32_ADC4_SAMPLE_FREQUENCY, #endif #ifdef ADC4_HAVE_DMA .dmachan = ADC4_DMA_CHAN, .hasdma = true, #endif }; static struct adc_dev_s g_adcdev4 = { .ad_ops = &g_adcops, .ad_priv = &g_adcpriv4, }; #endif /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: stm32_modifyreg32 * * Description: * Modify the value of a 32-bit register (not atomic). * * Input Parameters: * addr - The address of the register * clrbits - The bits to clear * setbits - The bits to set * * Returned Value: * None * ****************************************************************************/ #if defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F30XX) || \ defined(CONFIG_STM32_STM32F33XX) || defined(CONFIG_STM32_STM32F37XX) || \ defined(CONFIG_STM32_STM32F40XX) || defined(CONFIG_STM32_STM32L15XX) static void stm32_modifyreg32(unsigned int addr, uint32_t clrbits, uint32_t setbits) { putreg32((getreg32(addr) & ~clrbits) | setbits, addr); } #endif /**************************************************************************** * Name: adc_getreg * * Description: * Read the value of an ADC register. * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to read * * Returned Value: * The current contents of the specified register * ****************************************************************************/ static uint32_t adc_getreg(FAR struct stm32_dev_s *priv, int offset) { return getreg32(priv->base + offset); } /**************************************************************************** * Name: adc_putreg * * Description: * Write a value to an ADC register. * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to write to * value - The value to write to the register * * Returned Value: * None * ****************************************************************************/ static void adc_putreg(FAR struct stm32_dev_s *priv, int offset, uint32_t value) { putreg32(value, priv->base + offset); } /**************************************************************************** * Name: adc_modifyreg * * Description: * Modify the value of an ADC register (not atomic). * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to modify * clrbits - The bits to clear * setbits - The bits to set * * Returned Value: * None * ****************************************************************************/ static void adc_modifyreg(FAR struct stm32_dev_s *priv, int offset, uint32_t clrbits, uint32_t setbits) { adc_putreg(priv, offset, (adc_getreg(priv, offset) & ~clrbits) | setbits); } /**************************************************************************** * Name: tim_getreg * * Description: * Read the value of an ADC timer register. * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to read * * Returned Value: * The current contents of the specified register * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static uint16_t tim_getreg(FAR struct stm32_dev_s *priv, int offset) { return getreg16(priv->tbase + offset); } #endif /**************************************************************************** * Name: tim_putreg * * Description: * Write a value to an ADC timer register. * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to write to * value - The value to write to the register * * Returned Value: * None * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static void tim_putreg(FAR struct stm32_dev_s *priv, int offset, uint16_t value) { putreg16(value, priv->tbase + offset); } #endif /**************************************************************************** * Name: tim_modifyreg * * Description: * Modify the value of an ADC timer register (not atomic). * * Input Parameters: * priv - A reference to the ADC block status * offset - The offset to the register to modify * clrbits - The bits to clear * setbits - The bits to set * * Returned Value: * None * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static void tim_modifyreg(FAR struct stm32_dev_s *priv, int offset, uint16_t clrbits, uint16_t setbits) { tim_putreg(priv, offset, (tim_getreg(priv, offset) & ~clrbits) | setbits); } #endif /**************************************************************************** * Name: tim_dumpregs * * Description: * Dump all timer registers. * * Input parameters: * priv - A reference to the ADC block status * * Returned Value: * None * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static void tim_dumpregs(FAR struct stm32_dev_s *priv, FAR const char *msg) { ainfo("%s:\n", msg); ainfo(" CR1: %04x CR2: %04x SMCR: %04x DIER: %04x\n", tim_getreg(priv, STM32_GTIM_CR1_OFFSET), tim_getreg(priv, STM32_GTIM_CR2_OFFSET), tim_getreg(priv, STM32_GTIM_SMCR_OFFSET), tim_getreg(priv, STM32_GTIM_DIER_OFFSET)); ainfo(" SR: %04x EGR: 0000 CCMR1: %04x CCMR2: %04x\n", tim_getreg(priv, STM32_GTIM_SR_OFFSET), tim_getreg(priv, STM32_GTIM_CCMR1_OFFSET), tim_getreg(priv, STM32_GTIM_CCMR2_OFFSET)); ainfo(" CCER: %04x CNT: %04x PSC: %04x ARR: %04x\n", tim_getreg(priv, STM32_GTIM_CCER_OFFSET), tim_getreg(priv, STM32_GTIM_CNT_OFFSET), tim_getreg(priv, STM32_GTIM_PSC_OFFSET), tim_getreg(priv, STM32_GTIM_ARR_OFFSET)); ainfo(" CCR1: %04x CCR2: %04x CCR3: %04x CCR4: %04x\n", tim_getreg(priv, STM32_GTIM_CCR1_OFFSET), tim_getreg(priv, STM32_GTIM_CCR2_OFFSET), tim_getreg(priv, STM32_GTIM_CCR3_OFFSET), tim_getreg(priv, STM32_GTIM_CCR4_OFFSET)); #ifndef CONFIG_STM32_STM32L15XX if (priv->tbase == STM32_TIM1_BASE || priv->tbase == STM32_TIM8_BASE) { ainfo(" RCR: %04x BDTR: %04x DCR: %04x DMAR: %04x\n", tim_getreg(priv, STM32_ATIM_RCR_OFFSET), tim_getreg(priv, STM32_ATIM_BDTR_OFFSET), tim_getreg(priv, STM32_ATIM_DCR_OFFSET), tim_getreg(priv, STM32_ATIM_DMAR_OFFSET)); } else { ainfo(" DCR: %04x DMAR: %04x\n", tim_getreg(priv, STM32_GTIM_DCR_OFFSET), tim_getreg(priv, STM32_GTIM_DMAR_OFFSET)); } #endif } #endif /**************************************************************************** * Name: adc_timstart * * Description: * Start (or stop) the timer counter * * Input Parameters: * priv - A reference to the ADC block status * enable - True: Start conversion * * Returned Value: * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static void adc_timstart(FAR struct stm32_dev_s *priv, bool enable) { ainfo("enable: %d\n", enable ? 1 : 0); if (enable) { /* Start the counter */ tim_modifyreg(priv, STM32_GTIM_CR1_OFFSET, 0, GTIM_CR1_CEN); } else { /* Disable the counter */ tim_modifyreg(priv, STM32_GTIM_CR1_OFFSET, GTIM_CR1_CEN, 0); } } #endif /**************************************************************************** * Name: adc_timinit * * Description: * Initialize the timer that drivers the ADC sampling for this channel * using the pre-calculated timer divider definitions. * * Input Parameters: * priv - A reference to the ADC block status * * Returned Value: * Zero on success; a negated errno value on failure. * ****************************************************************************/ #ifdef ADC_HAVE_TIMER static int adc_timinit(FAR struct stm32_dev_s *priv) { uint32_t prescaler; uint32_t reload; uint32_t timclk; uint16_t clrbits = 0; uint16_t setbits = 0; uint16_t cr2; uint16_t ccmr1; uint16_t ccmr2; uint16_t ocmode1; uint16_t ocmode2; uint16_t ccenable; uint16_t ccer; uint16_t egr; /* If the timer base address is zero, then this ADC was not configured to * use a timer. */ if (priv->tbase == 0) { return ERROR; } /* EXTSEL selection: These bits select the external event used to trigger * the start of conversion of a regular group. NOTE: * * - The position with of the EXTSEL field varies from one STM32 MCU * to another. * - The width of the EXTSEL field varies from one STM32 MCU to another. * - The value in priv->extsel is already shifted into the correct bit * position. */ ainfo("Initializing timers extsel = 0x%08x\n", priv->extsel); adc_modifyreg(priv, STM32_ADC_EXTREG_OFFSET, ADC_EXTREG_EXTEN_MASK | ADC_EXTREG_EXTSEL_MASK, ADC_EXTREG_EXTEN_DEFAULT | priv->extsel); /* Configure the timer channel to drive the ADC */ /* Caculate optimal values for the timer prescaler and for the timer * reload register. If freq is the desired frequency, then * * reload = timclk / freq * reload = (pclck / prescaler) / freq * * There are many solutions to do this, but the best solution will be the * one that has the largest reload value and the smallest prescaler value. * That is the solution that should give us the most accuracy in the timer * control. Subject to: * * 0 <= prescaler <= 65536 * 1 <= reload <= 65535 * * So ( prescaler = pclck / 65535 / freq ) would be optimal. */ prescaler = (priv->pclck / priv->freq + 65534) / 65535; /* We need to decrement the prescaler value by one, but only, the value * does not underflow. */ if (prescaler < 1) { awarn("WARNING: Prescaler underflowed.\n"); prescaler = 1; } /* Check for overflow */ else if (prescaler > 65536) { awarn("WARNING: Prescaler overflowed.\n"); prescaler = 65536; } timclk = priv->pclck / prescaler; reload = timclk / priv->freq; if (reload < 1) { awarn("WARNING: Reload value underflowed.\n"); reload = 1; } else if (reload > 65535) { awarn("WARNING: Reload value overflowed.\n"); reload = 65535; } /* Disable the timer until we get it configured */ adc_timstart(priv, false); /* Set up the timer CR1 register. * * Select the Counter Mode == count up: * * ATIM_CR1_EDGE: The counter counts up or down depending on the * direction bit(DIR). * ATIM_CR1_DIR: 0: count up, 1: count down * * Set the clock division to zero for all */ clrbits = GTIM_CR1_DIR | GTIM_CR1_CMS_MASK | GTIM_CR1_CKD_MASK; setbits = GTIM_CR1_EDGE; tim_modifyreg(priv, STM32_GTIM_CR1_OFFSET, clrbits, setbits); /* Set the reload and prescaler values */ tim_putreg(priv, STM32_GTIM_PSC_OFFSET, prescaler-1); tim_putreg(priv, STM32_GTIM_ARR_OFFSET, reload); /* Clear the advanced timers repetition counter in TIM1 */ #ifndef CONFIG_STM32_STM32L15XX if (priv->tbase == STM32_TIM1_BASE || priv->tbase == STM32_TIM8_BASE) { tim_putreg(priv, STM32_ATIM_RCR_OFFSET, 0); tim_putreg(priv, STM32_ATIM_BDTR_OFFSET, ATIM_BDTR_MOE); /* Check me */ } #endif /* TIMx event generation: Bit 0 UG: Update generation */ tim_putreg(priv, STM32_GTIM_EGR_OFFSET, GTIM_EGR_UG); /* Handle channel specific setup */ ocmode1 = 0; ocmode2 = 0; switch (priv->trigger) { case 0: /* TimerX CC1 event */ { ccenable = ATIM_CCER_CC1E; ocmode1 = (ATIM_CCMR_CCS_CCOUT << ATIM_CCMR1_CC1S_SHIFT) | (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC1M_SHIFT) | ATIM_CCMR1_OC1PE; /* Set the event CC1 */ egr = ATIM_EGR_CC1G; /* Set the duty cycle by writing to the CCR register for this * channel */ tim_putreg(priv, STM32_GTIM_CCR1_OFFSET, (uint16_t)(reload >> 1)); } break; case 1: /* TimerX CC2 event */ { ccenable = ATIM_CCER_CC2E; ocmode1 = (ATIM_CCMR_CCS_CCOUT << ATIM_CCMR1_CC2S_SHIFT) | (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR1_OC2M_SHIFT) | ATIM_CCMR1_OC2PE; /* Set the event CC2 */ egr = ATIM_EGR_CC2G; /* Set the duty cycle by writing to the CCR register for this * channel */ tim_putreg(priv, STM32_GTIM_CCR2_OFFSET, (uint16_t)(reload >> 1)); } break; case 2: /* TimerX CC3 event */ { ccenable = ATIM_CCER_CC3E; ocmode2 = (ATIM_CCMR_CCS_CCOUT << ATIM_CCMR2_CC3S_SHIFT) | (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR2_OC3M_SHIFT) | ATIM_CCMR2_OC3PE; /* Set the event CC3 */ egr = ATIM_EGR_CC3G; /* Set the duty cycle by writing to the CCR register for this * channel */ tim_putreg(priv, STM32_GTIM_CCR3_OFFSET, (uint16_t)(reload >> 1)); } break; case 3: /* TimerX CC4 event */ { ccenable = ATIM_CCER_CC4E; ocmode2 = (ATIM_CCMR_CCS_CCOUT << ATIM_CCMR2_CC4S_SHIFT) | (ATIM_CCMR_MODE_PWM1 << ATIM_CCMR2_OC4M_SHIFT) | ATIM_CCMR2_OC4PE; /* Set the event CC4 */ egr = ATIM_EGR_CC4G; /* Set the duty cycle by writing to the CCR register for this * channel */ tim_putreg(priv, STM32_GTIM_CCR4_OFFSET, (uint16_t)(reload >> 1)); } break; case 4: /* TimerX TRGO event */ { /* TODO: TRGO support not yet implemented */ /* Set the event TRGO */ ccenable = 0; egr = GTIM_EGR_TG; /* Set the duty cycle by writing to the CCR register for this * channel */ tim_putreg(priv, STM32_GTIM_CCR4_OFFSET, (uint16_t)(reload >> 1)); } break; default: aerr("ERROR: No such trigger: %d\n", priv->trigger); return -EINVAL; } /* Disable the Channel by resetting the CCxE Bit in the CCER register */ ccer = tim_getreg(priv, STM32_GTIM_CCER_OFFSET); ccer &= ~ccenable; tim_putreg(priv, STM32_GTIM_CCER_OFFSET, ccer); /* Fetch the CR2, CCMR1, and CCMR2 register (already have ccer) */ cr2 = tim_getreg(priv, STM32_GTIM_CR2_OFFSET); ccmr1 = tim_getreg(priv, STM32_GTIM_CCMR1_OFFSET); ccmr2 = tim_getreg(priv, STM32_GTIM_CCMR2_OFFSET); /* Reset the Output Compare Mode Bits and set the select output compare * mode */ ccmr1 &= ~(ATIM_CCMR1_CC1S_MASK | ATIM_CCMR1_OC1M_MASK | ATIM_CCMR1_OC1PE | ATIM_CCMR1_CC2S_MASK | ATIM_CCMR1_OC2M_MASK | ATIM_CCMR1_OC2PE); ccmr2 &= ~(ATIM_CCMR2_CC3S_MASK | ATIM_CCMR2_OC3M_MASK | ATIM_CCMR2_OC3PE | ATIM_CCMR2_CC4S_MASK | ATIM_CCMR2_OC4M_MASK | ATIM_CCMR2_OC4PE); ccmr1 |= ocmode1; ccmr2 |= ocmode2; /* Reset the output polarity level of all channels (selects high * polarity) */ ccer &= ~(ATIM_CCER_CC1P | ATIM_CCER_CC2P | ATIM_CCER_CC3P | ATIM_CCER_CC4P); /* Enable the output state of the selected channel (only) */ ccer &= ~(ATIM_CCER_CC1E | ATIM_CCER_CC2E | ATIM_CCER_CC3E | ATIM_CCER_CC4E); ccer |= ccenable; #ifndef CONFIG_STM32_STM32L15XX if (priv->tbase == STM32_TIM1_BASE || priv->tbase == STM32_TIM8_BASE) { /* Reset output N polarity level, output N state, output compare state, * output compare N idle state. */ # if defined(CONFIG_STM32_STM32F20XX) || \ defined(CONFIG_STM32_STM32F30XX) || \ defined(CONFIG_STM32_STM32F40XX) ccer &= ~(ATIM_CCER_CC1NE | ATIM_CCER_CC1NP | ATIM_CCER_CC2NE | ATIM_CCER_CC2NP | ATIM_CCER_CC3NE | ATIM_CCER_CC3NP | ATIM_CCER_CC4NP); # else ccer &= ~(ATIM_CCER_CC1NE | ATIM_CCER_CC1NP | ATIM_CCER_CC2NE | ATIM_CCER_CC2NP | ATIM_CCER_CC3NE | ATIM_CCER_CC3NP); # endif /* Reset the output compare and output compare N IDLE State */ cr2 &= ~(ATIM_CR2_OIS1 | ATIM_CR2_OIS1N | ATIM_CR2_OIS2 | ATIM_CR2_OIS2N | ATIM_CR2_OIS3 | ATIM_CR2_OIS3N | ATIM_CR2_OIS4); } # if defined(CONFIG_STM32_STM32F20XX) || \ defined(CONFIG_STM32_STM32F30XX) || \ defined(CONFIG_STM32_STM32F40XX) else { ccer &= ~(GTIM_CCER_CC1NP | GTIM_CCER_CC2NP | GTIM_CCER_CC3NP); } # endif #else /* For the STM32L15XX family only these timers can be used: 2-4, 6, 7, 9, 10 * Reset the output compare and output compare N IDLE State */ if (priv->tbase >= STM32_TIM2_BASE && priv->tbase <= STM32_TIM4_BASE) { /* Reset output N polarity level, output N state, output compare state, * output compare N idle state. */ ccer &= ~(ATIM_CCER_CC1NE | ATIM_CCER_CC1NP | ATIM_CCER_CC2NE | ATIM_CCER_CC2NP | ATIM_CCER_CC3NE | ATIM_CCER_CC3NP | ATIM_CCER_CC4NP); } #endif /* Save the modified register values */ tim_putreg(priv, STM32_GTIM_CR2_OFFSET, cr2); tim_putreg(priv, STM32_GTIM_CCMR1_OFFSET, ccmr1); tim_putreg(priv, STM32_GTIM_CCMR2_OFFSET, ccmr2); tim_putreg(priv, STM32_GTIM_CCER_OFFSET, ccer); tim_putreg(priv, STM32_GTIM_EGR_OFFSET, egr); /* Set the ARR Preload Bit */ tim_modifyreg(priv, STM32_GTIM_CR1_OFFSET, 0, GTIM_CR1_ARPE); /* Enable the timer counter */ adc_timstart(priv, true); tim_dumpregs(priv, "After starting timers"); return OK; } #endif /**************************************************************************** * Name: adc_startconv * * Description: * Start (or stop) the ADC conversion process * * Input Parameters: * priv - A reference to the ADC block status * enable - True: Start conversion * * Returned Value: * ****************************************************************************/ #if defined(CONFIG_STM32_STM32F10XX) static void adc_startconv(FAR struct stm32_dev_s *priv, bool enable) { ainfo("enable: %d\n", enable ? 1 : 0); if (!enable) { /* Clear ADON to stop the conversion and put the ADC in the * power down state. */ adc_enable(priv, false); } /* If the ADC is already on, set ADON again to start the conversion. * Otherwise, set ADON once to wake up the ADC from the power down state. */ adc_enable(priv, true); } #elif defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) static void adc_startconv(FAR struct stm32_dev_s *priv, bool enable) { uint32_t regval; ainfo("enable: %d\n", enable ? 1 : 0); if (enable) { /* Start the conversion of regular channels */ adc_modifyreg(priv, STM32_ADC_CR_OFFSET, 0, ADC_CR_ADSTART); } else { regval = adc_getreg(priv, STM32_ADC_CR_OFFSET); /* Is a conversion ongoing? */ if ((regval & ADC_CR_ADSTART) != 0) { /* Stop the conversion */ adc_putreg(priv, STM32_ADC_CR_OFFSET, regval | ADC_CR_ADSTP); /* Wait for the conversion to stop */ while ((adc_getreg(priv, STM32_ADC_CR_OFFSET) & ADC_CR_ADSTP) != 0); } } } #else static void adc_startconv(FAR struct stm32_dev_s *priv, bool enable) { ainfo("enable: %d\n", enable ? 1 : 0); if (enable) { /* Start the conversion of regular channels */ adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, 0, ADC_CR2_SWSTART); } else { /* Stop the conversion */ adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, ADC_CR2_SWSTART, 0); } } #endif /**************************************************************************** * Name: adc_rccreset * * Description: * Deinitializes the ADCx peripheral registers to their default * reset values. It could set all the ADCs configured. * * Input Parameters: * regaddr - The register to read * reset - Condition, set or reset * * Returned Value: * ****************************************************************************/ static void adc_rccreset(FAR struct stm32_dev_s *priv, bool reset) { uint32_t adcbit; /* Pick the appropriate bit in the APB2 reset register. * For the STM32 F1, there is an individual bit to reset each ADC, * but for the STM32 F2/F4, there is one common reset for all ADCs. * THIS will probably cause some problems! */ switch (priv->intf) { #ifdef CONFIG_STM32_ADC1 case 1: adcbit = RCC_RSTR_ADC1RST; break; #endif #ifdef CONFIG_STM32_ADC2 case 2: adcbit = RCC_RSTR_ADC2RST; break; #endif #ifdef CONFIG_STM32_ADC3 case 3: adcbit = RCC_RSTR_ADC3RST; break; #endif #ifdef CONFIG_STM32_ADC4 case 4: adcbit = RCC_RSTR_ADC4RST; break; #endif default: return; } /* Set or clear the selected bit in the APB2 reset register. * modifyreg32() disables interrupts. Disabling interrupts is necessary * because the APB2RTSR register is used by several different drivers. */ if (reset) { /* Enable ADC reset state */ modifyreg32(STM32_RCC_RSTR, 0, adcbit); } else { /* Release ADC from reset state */ modifyreg32(STM32_RCC_RSTR, adcbit, 0); } } /**************************************************************************** * Name: adc_power_down_idle * * Description : Enables or disables power down during the idle phase. * * Input Parameters: * * priv - pointer to the adc device structure * pdi_high - true: The ADC is powered down when waiting for a start event * false: The ADC is powered up when waiting for a start event * * Returned Value: * None. * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_power_down_idle(FAR struct stm32_dev_s *priv, bool pdi_high) { uint32_t regval; ainfo("PDI: %d\n", pdi_high ? 1 : 0); regval = adc_getreg(priv, STM32_ADC_CR1_OFFSET); if ((STM32_ADC1_CR2 & ADC_CR2_ADON) == 0) { if (pdi_high) { regval |= ADC_CR1_PDI; } else { regval &= ~ADC_CR1_PDI; } adc_putreg(priv, STM32_ADC_CR1_OFFSET, regval); } } #endif /**************************************************************************** * Name: adc_power_down_delay * * Description : Enables or disables power down during the delay phase. * * Input Parameters: * * priv - pointer to the adc device structure * pdd_high - true: The ADC is powered down when waiting for a start event * false: The ADC is powered up when waiting for a start event * * Returned Value: * None. * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_power_down_delay(FAR struct stm32_dev_s *priv, bool pdd_high) { uint32_t regval; ainfo("PDD: %d\n", pdd_high ? 1 : 0); regval = adc_getreg(priv, STM32_ADC_CR1_OFFSET); if ((STM32_ADC1_CR2 & ADC_CR2_ADON) == 0) { if (pdd_high) { regval |= ADC_CR1_PDD; } else { regval &= ~ADC_CR1_PDD; } adc_putreg(priv, STM32_ADC_CR1_OFFSET, regval); } } #endif /**************************************************************************** * Name: adc_dels_after_conversion * * Description : Defines the length of the delay which is applied * after a conversion or a sequence of conversions. * * Input Parameters: * * priv - pointer to the adc device structure * delay - delay selection (see definition in chip/chip/stm32_adc.h * starting from line 284) * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_dels_after_conversion(FAR struct stm32_dev_s *priv, uint32_t delay) { ainfo("Delay selected: 0x%08x\n", delay); adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, ADC_CR2_DELS_MASK, delay); } #endif /**************************************************************************** * Name: adc_select_ch_bank * * Description : Selects the bank of channels to be converted * (! Must be modified only when no conversion is on going !) * * Input Parameters: * * priv - pointer to the adc device structure * enable - true: bank of channels B selected * false: bank of channels A selected * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_select_ch_bank(FAR struct stm32_dev_s *priv, bool chb_selected) { ainfo("Bank of channels selected: %c\n", chb_selected ? 'B' : 'A'); if (chb_selected) { adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, 0, ADC_CR2_CFG); } else { adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, ADC_CR2_CFG, 0); } } #endif /**************************************************************************** * Name: adc_enable * * Description : Enables or disables the specified ADC peripheral. * Also, starts a conversion when the ADC is not * triggered by timers * * Input Parameters: * * enable - true: enable ADC conversion * false: disable ADC conversion * * Returned Value: * ****************************************************************************/ #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) static void adc_enable(FAR struct stm32_dev_s *priv, bool enable) { uint32_t regval; ainfo("enable: %d\n", enable ? 1 : 0); regval = adc_getreg(priv, STM32_ADC_CR_OFFSET); if (enable) { /* Enable the ADC */ adc_putreg(priv, STM32_ADC_CR_OFFSET, regval | ADC_CR_ADEN); /* Wait for the ADC to be ready */ while ((adc_getreg(priv, STM32_ADC_ISR_OFFSET) & ADC_INT_ARDY) == 0); } else if ((regval & ADC_CR_ADEN) != 0 && (regval & ADC_CR_ADDIS) == 0) { /* Stop ongoing conversions */ adc_startconv(priv, false); /* Disable the ADC */ adc_putreg(priv, STM32_ADC_CR_OFFSET, regval | ADC_CR_ADDIS); /* Wait for the ADC to be disabled */ while ((adc_getreg(priv, STM32_ADC_CR_OFFSET) & ADC_CR_ADEN) != 0); } } #else static void adc_enable(FAR struct stm32_dev_s *priv, bool enable) { #ifdef ADC_SR_ADONS bool enabled = (adc_getreg(priv, STM32_ADC_SR_OFFSET) & ADC_SR_ADONS) != 0; #else bool enabled = false; #endif ainfo("enable: %d\n", enable ? 1 : 0); if (!enabled && enable) { adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, 0, ADC_CR2_ADON); } else if (enabled && !enable) { adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, ADC_CR2_ADON, 0); } } #endif /**************************************************************************** * Name: adc_write_sample_time_registers * * Description: * Writes previously defined values into ADC_SMPR0, ADC_SMPR1, ADC_SMPR2 * and ADC_SMPR3 registers * * Input Parameters: * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_write_sample_time_registers(FAR struct adc_dev_s *dev) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; uint32_t value = 0; uint8_t i; uint8_t shift; /* Sampling time individually for each channel * 000: 4 cycles * 001: 9 cycles * 010: 16 cycles * 011: 24 cycles * 100: 48 cycles * 101: 96 cycles * 110: 192 cycles * 111: 384 cycles - selected for all channels */ for (i = 0, shift = 0; i < 32; i++) { value |= priv->sample_rate[i] << (shift * 3); switch (i) { case 9: adc_putreg(priv, STM32_ADC_SMPR3_OFFSET, value); shift = 0; value = 0; break; case 19: adc_putreg(priv, STM32_ADC_SMPR2_OFFSET, value); shift = 0; value = 0; break; case 29: adc_putreg(priv, STM32_ADC_SMPR1_OFFSET, value); shift = 0; value = 0; break; case 31: adc_putreg(priv, STM32_ADC_SMPR0_OFFSET, value); shift = 0; value = 0; break; default: shift++; break; } } } #endif /**************************************************************************** * Name: adc_dmaconvcallback * * Description: * Callback for DMA. Called from the DMA transfer complete interrupt after * all channels have been converted and transferred with DMA. * * Input Parameters: * * handle - handle to DMA * isr - * arg - adc device * * Returned Value: * ****************************************************************************/ #ifdef ADC_HAVE_DMA static void adc_dmaconvcallback(DMA_HANDLE handle, uint8_t isr, FAR void *arg) { FAR struct adc_dev_s *dev = (FAR struct adc_dev_s *)arg; FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; int i; /* Verify that the upper-half driver has bound its callback functions */ if (priv->cb != NULL) { DEBUGASSERT(priv->cb->au_receive != NULL); for (i = 0; i < priv->nchannels; i++) { priv->cb->au_receive(dev, priv->chanlist[priv->current], priv->dmabuffer[priv->current]); priv->current++; if (priv->current >= priv->nchannels) { /* Restart the conversion sequence from the beginning */ priv->current = 0; } } } /* Restart DMA for the next conversion series */ adc_modifyreg(priv, STM32_ADC_DMAREG_OFFSET, ADC_DMAREG_DMA, 0); adc_modifyreg(priv, STM32_ADC_DMAREG_OFFSET, 0, ADC_DMAREG_DMA); } #endif /**************************************************************************** * Name: adc_bind * * Description: * Bind the upper-half driver callbacks to the lower-half implementation. * This must be called early in order to receive ADC event notifications. * ****************************************************************************/ static int adc_bind(FAR struct adc_dev_s *dev, FAR const struct adc_callback_s *callback) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; DEBUGASSERT(priv != NULL); priv->cb = callback; return OK; } /**************************************************************************** * Name: adc_reset * * Description: * Reset the ADC device. Called early to initialize the hardware. * This is called, before adc_setup() and on error conditions. * * Input Parameters: * * Returned Value: * ****************************************************************************/ static void adc_reset(FAR struct adc_dev_s *dev) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; irqstate_t flags; uint32_t clrbits; uint32_t setbits; #ifdef ADC_HAVE_TIMER int ret; #endif ainfo("intf: %d\n", priv->intf); flags = enter_critical_section(); #if defined(CONFIG_STM32_STM32L15XX) && \ (STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI) /* The STM32L15XX family uses HSI as an independent clock-source * for the ADC */ adc_enable_hsi(true); #endif #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) /* Turn off the ADC so we can write the RCC bits */ adc_enable(priv, false); #endif /* Enable ADC reset state */ adc_rccreset(priv, true); /* Release ADC from reset state */ adc_rccreset(priv, false); #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) /* Set voltage regular enable to intermediate state */ adc_modifyreg(priv, STM32_ADC_CR_OFFSET, ADC_CR_ADVREGEN_MASK, ADC_CR_ADVREGEN_INTER); /* Enable the ADC voltage regulator */ adc_modifyreg(priv, STM32_ADC_CR_OFFSET, ADC_CR_ADVREGEN_MASK, ADC_CR_ADVREGEN_ENABLED); /* Wait for the ADC voltage regulator to startup */ up_udelay(10); #if 0 /* Doesn't work */ /* Calibrate the ADC */ adc_modifyreg(priv, STM32_ADC_CR_OFFSET, ADC_CR_ADCALDIF, AD_CR_ADCAL); /* Wait for the calibration to complete */ while ((adc_getreg(priv, STM32_ADC_CR_OFFSET) & ADC_CR_ADCAL) != 0); #endif /* Initialize the watchdog 1 threshold register */ adc_putreg(priv, STM32_ADC_TR1_OFFSET, 0x0fff0000); #else /* Initialize the watchdog high threshold register */ adc_putreg(priv, STM32_ADC_HTR_OFFSET, 0x00000fff); /* Initialize the watchdog low threshold register */ adc_putreg(priv, STM32_ADC_LTR_OFFSET, 0x00000000); #endif /* Initialize the same sample time for each ADC. * During sample cycles channel selection bits must remain unchanged. */ #ifdef CONFIG_STM32_STM32L15XX adc_write_sample_time_registers(dev); #else adc_putreg(priv, STM32_ADC_SMPR1_OFFSET, ADC_SMPR1_DEFAULT); adc_putreg(priv, STM32_ADC_SMPR2_OFFSET, ADC_SMPR2_DEFAULT); #endif #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) /* Enable the analog watchdog */ clrbits = ADC_CFGR_AWD1CH_MASK; setbits = ADC_CFGR_AWD1EN | ADC_CFGR_AWD1SGL | (priv->chanlist[0] << ADC_CFGR_AWD1CH_SHIFT); /* Set the resolution of the conversion */ clrbits |= ADC_CFGR_RES_MASK; setbits |= ADC_CFGR_RES_12BIT; #ifdef ADC_HAVE_DMA if (priv->hasdma) { /* Set DMA one shot mode */ clrbits |= ADC_CFGR_DMACFG; /* Enable DMA */ setbits |= ADC_CFGR_DMAEN; } #endif /* Disable continuous mode and set align to right */ clrbits |= ADC_CFGR_CONT | ADC_CFGR_ALIGN; /* Disable external trigger for regular channels */ clrbits |= ADC_CFGR_EXTEN_MASK; setbits |= ADC_CFGR_EXTEN_NONE; /* Set CFGR configuration */ adc_modifyreg(priv, STM32_ADC_CFGR_OFFSET, clrbits, setbits); /* Enable interrupt flags, but disable overrun interrupt */ clrbits = ADC_IER_OVR; setbits = ADC_IER_ALLINTS & ~ADC_IER_OVR; /* Set IER configuration */ adc_modifyreg(priv, STM32_ADC_IER_OFFSET, clrbits, setbits); #else /* CONFIG_STM32_STM32F30XX || CONFIG_STM32_STM33XX */ /* Enable the analog watchdog */ clrbits = ADC_CR1_AWDCH_MASK; setbits = ADC_CR1_AWDEN | (priv->chanlist[0] << ADC_CR1_AWDCH_SHIFT); #ifdef CONFIG_STM32_STM32F10XX /* Set independent mode */ clrbits |= ADC_CR1_DUALMOD_MASK; setbits |= ADC_CR1_IND; #elif (! defined(CONFIG_STM32_STM32F37XX)) /* Set the resolution of the conversion */ clrbits |= ADC_CR1_RES_MASK; setbits |= ADC_CR1_RES_12BIT; #endif #ifdef ADC_HAVE_DMA if (priv->hasdma) { setbits |= ADC_CR1_SCAN; } #endif /* Enable interrupt flags, but disable overrun interrupt: TODO this is * done later by upper half when opening device by adc_rxint(). */ #ifndef CONFIG_STM32_STM32F37XX clrbits |= ADC_IER_OVR; setbits |= ADC_IER_ALLINTS & ~ADC_IER_OVR; #else /* TODO NON DMA mode */ #endif /* Set CR1 configuration */ adc_modifyreg(priv, STM32_ADC_CR1_OFFSET, clrbits, setbits); #ifdef CONFIG_STM32_STM32L15XX /* Disables power down during the delay phase */ adc_power_down_idle(priv, false); adc_power_down_delay(priv, false); /* Select the bank of channels A */ adc_select_ch_bank(priv, false); /* Delay until the converted data has been read */ adc_dels_after_conversion(priv, ADC_CR2_DELS_TILLRD); #endif /* Disable continuous mode and set align to right */ clrbits = ADC_CR2_CONT | ADC_CR2_ALIGN; setbits = 0; /* Disable external trigger for regular channels */ clrbits |= ADC_EXTREG_EXTEN_MASK; setbits |= ADC_EXTREG_EXTEN_NONE; /* Enable software trigger for regular channels */ #ifdef CONFIG_STM32_STM32F37XX clrbits |= ADC_CR2_EXTSEL_MASK; setbits |= ADC_CR2_EXTSEL_SWSTART | ADC_CR2_EXTTRIG; /* SW is considered as external trigger */ #endif #ifdef ADC_HAVE_DMA if (priv->hasdma) { setbits |= ADC_CR2_DMA; } #endif /* Set CR2 configuration */ adc_modifyreg(priv, STM32_ADC_CR2_OFFSET, clrbits, setbits); #endif /* Configuration of the channel conversions */ adc_set_ch(dev, 0); /* ADC CCR configuration */ #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) clrbits = ADC_CCR_DUAL_MASK | ADC_CCR_DELAY_MASK | ADC_CCR_DMACFG | ADC_CCR_MDMA_MASK | ADC_CCR_CKMODE_MASK | ADC_CCR_VREFEN | ADC_CCR_TSEN | ADC_CCR_VBATEN; setbits = ADC_CCR_DUAL_IND | ADC_CCR_DELAY(0) | ADC_CCR_MDMA_DISABLED | ADC_CCR_CKMODE_ASYNCH; if (priv->base == STM32_ADC1_BASE || priv->base == STM32_ADC2_BASE) { stm32_modifyreg32(STM32_ADC12_CCR, clrbits, setbits); } #ifndef CONFIG_STM32_STM32F33XX else { stm32_modifyreg32(STM32_ADC34_CCR, clrbits, setbits); } #endif #elif defined(CONFIG_STM32_STM32F20XX) || \ defined(CONFIG_STM32_STM32F40XX) || \ defined(CONFIG_STM32_STM32L15XX) clrbits = ADC_CCR_ADCPRE_MASK | ADC_CCR_TSVREFE; setbits = ADC_CCR_ADCPRE_DIV2; #if defined(CONFIG_STM32_STM32F20XX) || defined(CONFIG_STM32_STM32F40XX) clrbits |= ADC_CCR_MULTI_MASK | ADC_CCR_DELAY_MASK | ADC_CCR_DDS | ADC_CCR_DMA_MASK | ADC_CCR_VBATE; setbits |= ADC_CCR_MULTI_NONE | ADC_CCR_DMA_DISABLED; #endif stm32_modifyreg32(STM32_ADC_CCR, clrbits, setbits); #endif #ifdef ADC_HAVE_DMA /* Enable DMA */ if (priv->hasdma) { /* Stop and free DMA if it was started before */ if (priv->dma != NULL) { stm32_dmastop(priv->dma); stm32_dmafree(priv->dma); } priv->dma = stm32_dmachannel(priv->dmachan); stm32_dmasetup(priv->dma, priv->base + STM32_ADC_DR_OFFSET, (uint32_t)priv->dmabuffer, priv->nchannels, ADC_DMA_CONTROL_WORD); stm32_dmastart(priv->dma, adc_dmaconvcallback, dev, false); } #endif /* Set ADON to wake up the ADC from the power down state */ adc_enable(priv, true); #ifdef ADC_HAVE_TIMER if (priv->tbase != 0) { ret = adc_timinit(priv); if (ret < 0) { aerr("ERROR: adc_timinit failed: %d\n", ret); } } #ifndef CONFIG_ADC_NO_STARTUP_CONV else #endif #endif #ifndef CONFIG_ADC_NO_STARTUP_CONV { adc_startconv(priv, true); } #endif leave_critical_section(flags); #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) ainfo("ISR: 0x%08x CR: 0x%08x CFGR: 0x%08x\n", adc_getreg(priv, STM32_ADC_ISR_OFFSET), adc_getreg(priv, STM32_ADC_CR_OFFSET), adc_getreg(priv, STM32_ADC_CFGR_OFFSET)); #else ainfo("SR: 0x%08x CR1: 0x%08x CR2: 0x%08x\n", adc_getreg(priv, STM32_ADC_SR_OFFSET), adc_getreg(priv, STM32_ADC_CR1_OFFSET), adc_getreg(priv, STM32_ADC_CR2_OFFSET)); #endif ainfo("SQR1: 0x%08x SQR2: 0x%08x SQR3: 0x%08x\n", adc_getreg(priv, STM32_ADC_SQR1_OFFSET), adc_getreg(priv, STM32_ADC_SQR2_OFFSET), adc_getreg(priv, STM32_ADC_SQR3_OFFSET)); #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) ainfo("SQR4: 0x%08x\n", adc_getreg(priv, STM32_ADC_SQR4_OFFSET)); #elif defined(CONFIG_STM32_STM32L15XX) ainfo("SQR4: 0x%08x SQR5: 0x%08x\n", adc_getreg(priv, STM32_ADC_SQR4_OFFSET) adc_getreg(priv, STM32_ADC_SQR5_OFFSET)); #endif #if defined(CONFIG_STM32_STM32F30XX) || defined(CONFIG_STM32_STM32F33XX) if (priv->base == STM32_ADC1_BASE || priv->base == STM32_ADC2_BASE) { ainfo("CCR: 0x%08x\n", getreg32(STM32_ADC12_CCR)); } #ifndef CONFIG_STM32_STM32F33XX else { ainfo("CCR: 0x%08x\n", getreg32(STM32_ADC34_CCR)); } #endif #elif defined(CONFIG_STM32_STM32F20XX) || \ defined(CONFIG_STM32_STM32F40XX) || \ defined(CONFIG_STM32_STM32L15XX) ainfo("CCR: 0x%08x\n", getreg32(STM32_ADC_CCR)); #endif } /**************************************************************************** * Name: adc_reset_hsi_disable * * Description: * Reset the ADC device with HSI and ADC shut down. Called early to * initialize the hardware. This is called, before adc_setup() and on * error conditions. In STM32L15XX case sometimes HSI must be shut * down after the first initialization * * Input Parameters: * * Returned Value: * ****************************************************************************/ #if defined(CONFIG_STM32_STM32L15XX) && \ (STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI) static void adc_reset_hsi_disable(FAR struct adc_dev_s *dev) { adc_reset(dev); adc_shutdown(dev); } #endif /**************************************************************************** * Name: adc_setup * * Description: * Configure the ADC. This method is called the first time that the ADC * device is opened. This will occur when the port is first opened. * This setup includes configuring and attaching ADC interrupts. * Interrupts are all disabled upon return. * * Input Parameters: * * Returned Value: * ****************************************************************************/ static int adc_setup(FAR struct adc_dev_s *dev) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; int ret; /* Attach the ADC interrupt */ ret = irq_attach(priv->irq, priv->isr, NULL); if (ret < 0) { ainfo("irq_attach failed: %d\n", ret); return ret; } /* Make sure that the ADC device is in the powered up, reset state */ adc_reset(dev); /* Enable the ADC interrupt */ ainfo("Enable the ADC interrupt: irq=%d\n", priv->irq); up_enable_irq(priv->irq); return ret; } /**************************************************************************** * Name: adc_shutdown * * Description: * Disable the ADC. This method is called when the ADC device is closed. * This method reverses the operation the setup method. * * Input Parameters: * * Returned Value: * ****************************************************************************/ static void adc_shutdown(FAR struct adc_dev_s *dev) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; adc_enable(priv, false); #if defined(CONFIG_STM32_STM32L15XX) && \ (STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI) adc_enable_hsi(false); #endif /* Disable ADC interrupts and detach the ADC interrupt handler */ up_disable_irq(priv->irq); irq_detach(priv->irq); /* Disable and reset the ADC module */ adc_rccreset(priv, true); } /**************************************************************************** * Name: adc_rxint * * Description: * Call to enable or disable RX interrupts. * * Input Parameters: * * Returned Value: * ****************************************************************************/ static void adc_rxint(FAR struct adc_dev_s *dev, bool enable) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; uint32_t regval; ainfo("intf: %d enable: %d\n", priv->intf, enable ? 1 : 0); if (enable) { /* Enable the analog watchdog / overrun interrupts, and if no DMA, * end-of-conversion ADC. */ regval = ADC_IER_ALLINTS; #ifdef ADC_HAVE_DMA if (priv->hasdma) { regval &= ~(ADC_IER_EOC | ADC_IER_JEOC); } #endif adc_modifyreg(priv, STM32_ADC_IER_OFFSET, 0, regval); } else { /* Disable all ADC interrupts */ adc_modifyreg(priv, STM32_ADC_IER_OFFSET, ADC_IER_ALLINTS, 0); } } /**************************************************************************** * Name: adc_enable_tvref_register * * Description: * Enable/disable the temperature sensor and the VREFINT channel. * * Input Parameters: * dev - pointer to device structure used by the driver * enable - true: Temperature sensor and V REFINT channel enabled * (ch 16 and 17) * false: Temperature sensor and V REFINT channel disabled * (ch 16 and 17) * * Returned Value: * None. * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_ioc_enable_tvref_register(FAR struct adc_dev_s *dev, bool enable) { if (enable) { stm32_modifyreg32(STM32_ADC_CCR, 0, ADC_CCR_TSVREFE); } else { stm32_modifyreg32(STM32_ADC_CCR, ADC_CCR_TSVREFE, 0); } ainfo("STM32_ADC_CCR value: 0x%08x\n", getreg32(STM32_ADC_CCR)); } #endif /**************************************************************************** * Name: adc_ioc_change_sleep_between_opers * * Description: * Changes PDI and PDD bits to save battery. * * Input Parameters: * dev - pointer to device structure used by the driver * cmd - command * arg - arguments passed with command * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static int adc_ioc_change_sleep_between_opers(FAR struct adc_dev_s *dev, int cmd, bool arg) { int ret = OK; FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; adc_enable(priv, false); switch (cmd) { case IO_ENABLE_DISABLE_PDI: adc_power_down_idle(priv, arg); break; case IO_ENABLE_DISABLE_PDD: adc_power_down_delay(priv, arg); break; case IO_ENABLE_DISABLE_PDD_PDI: adc_power_down_idle(priv, arg); adc_power_down_delay(priv, arg); break; default: ainfo("unknown cmd: %d\n", cmd); break; } adc_enable(priv, true); return ret; } #endif /**************************************************************************** * Name: adc_ioc_enable_awd_int * * Description: * Turns ON/OFF ADC analog watchdog interrupt. * * Input Parameters: * dev - pointer to device structure used by the driver * arg - true: Turn ON interrupt * false: Turn OFF interrupt * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_ioc_enable_awd_int(FAR struct stm32_dev_s *priv, bool enable) { if (enable) { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, 0, ADC_IER_AWD); } else { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, ADC_IER_AWD, 0); } } #endif /**************************************************************************** * Name: adc_ioc_enable_eoc_int * * Description: * Turns ON/OFF ADC EOC interrupt. * * Input Parameters: * dev - pointer to device structure used by the driver * arg - true: Turn ON interrupt * false: Turn OFF interrupt * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_ioc_enable_eoc_int(FAR struct stm32_dev_s *priv, bool enable) { if (enable) { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, 0, ADC_IER_EOC); } else { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, ADC_IER_EOC, 0); } } #endif /**************************************************************************** * Name: adc_ioc_enable_jeoc_int * * Description: * Turns ON/OFF ADC injected channels interrupt. * * Input Parameters: * dev - pointer to device structure used by the driver * arg - true: Turn ON interrupt * false: Turn OFF interrupt * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_ioc_enable_jeoc_int(FAR struct stm32_dev_s *priv, bool enable) { if (enable) { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, 0, ADC_IER_JEOC); } else { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, ADC_IER_JEOC, 0); } } #endif /**************************************************************************** * Name: adc_ioc_enable_ovr_int * * Description: * Turns ON/OFF ADC overrun interrupt. * * Input Parameters: * dev - pointer to device structure used by the driver * arg - true: Turn ON interrupt * false: Turn OFF interrupt * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static void adc_ioc_enable_ovr_int(FAR struct stm32_dev_s *priv, bool enable) { if (enable) { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, 0, ADC_IER_OVR); } else { adc_modifyreg(priv, STM32_ADC_IER_OFFSET, ADC_IER_OVR, 0); } } #endif /**************************************************************************** * Name: adc_ioc_change_ints * * Description: * Turns ON/OFF ADC interrupts. * * Input Parameters: * dev - pointer to device structure used by the driver * cmd - command * arg - arguments passed with command * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static int adc_ioc_change_ints(FAR struct adc_dev_s *dev, int cmd, bool arg) { int ret = OK; FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; switch (cmd) { case IO_ENABLE_DISABLE_AWDIE: adc_ioc_enable_awd_int(priv, arg); break; case IO_ENABLE_DISABLE_EOCIE: adc_ioc_enable_eoc_int(priv, arg); break; case IO_ENABLE_DISABLE_JEOCIE: adc_ioc_enable_jeoc_int(priv, arg); break; case IO_ENABLE_DISABLE_OVRIE: adc_ioc_enable_ovr_int(priv, arg); break; case IO_ENABLE_DISABLE_ALL_INTS: adc_ioc_enable_awd_int(priv, arg); adc_ioc_enable_eoc_int(priv, arg); adc_ioc_enable_jeoc_int(priv, arg); adc_ioc_enable_ovr_int(priv, arg); break; default: ainfo("unknown cmd: %d\n", cmd); break; } return ret; } #endif /**************************************************************************** * Name: adc_ioc_wait_rcnr_zeroed * * Description: * For the STM3215XX-family the ADC_SR_RCNR bit must be zeroed, * before next conversion. * * Input Parameters: * dev - pointer to device structure used by the driver * * Returned Value: * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX static int adc_ioc_wait_rcnr_zeroed(FAR struct stm32_dev_s *priv) { int i; for (i = 0; i < 30000; i++) { if ((adc_getreg(priv, STM32_ADC_SR_OFFSET) & ADC_SR_RCNR) == 0) { return OK; } } return -ENODATA; } #endif /**************************************************************************** * Name: adc_enable_hsi * * Description: * Enable/Disable HSI clock * * Input Parameters: * enable - true : HSI clock for ADC enabled * false : HSI clock for ADC disabled * * Returned Value: * ****************************************************************************/ #if defined(CONFIG_STM32_STM32L15XX) && \ (STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI) static void adc_enable_hsi(bool enable) { if (enable) { /* Enable the HSI */ stm32_modifyreg32(STM32_RCC_CR, 0, RCC_CR_HSION); while ((getreg32(STM32_RCC_CR) & RCC_CR_HSIRDY) == 0); } else { /* Disable the HSI */ stm32_modifyreg32(STM32_RCC_CR, RCC_CR_HSION, 0); } } #endif /**************************************************************************** * Name: adc_sqrbits ****************************************************************************/ static uint32_t adc_sqrbits(FAR struct stm32_dev_s *priv, int first, int last, int offset) { uint32_t bits = 0; int i; for (i = first - 1; i < priv->nchannels && i < last; i++, offset += ADC_SQ_OFFSET) { bits |= (uint32_t)priv->chanlist[i] << offset; } return bits; } /**************************************************************************** * Name: adc_set_ch * * Description: * Sets the ADC channel. * * Input Parameters: * dev - pointer to device structure used by the driver * ch - ADC channel number + 1. 0 reserved for all configured channels * * Returned Value: * int - errno * ****************************************************************************/ static int adc_set_ch(FAR struct adc_dev_s *dev, uint8_t ch) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; uint32_t bits; int i; if (ch == 0) { priv->current = 0; priv->nchannels = priv->cchannels; } else { for (i = 0; i < priv->cchannels && priv->chanlist[i] != ch - 1; i++); if (i >= priv->cchannels) { return -ENODEV; } priv->current = i; priv->nchannels = 1; } #ifdef STM32_ADC_SQR5_OFFSET bits = adc_sqrbits(priv, ADC_SQR5_FIRST, ADC_SQR5_LAST, ADC_SQR5_SQ_OFFSET); adc_modifyreg(priv, STM32_ADC_SQR5_OFFSET, ~ADC_SQR5_RESERVED, bits); #endif #ifdef STM32_ADC_SQR4_OFFSET bits = adc_sqrbits(priv, ADC_SQR4_FIRST, ADC_SQR4_LAST, ADC_SQR4_SQ_OFFSET); adc_modifyreg(priv, STM32_ADC_SQR4_OFFSET, ~ADC_SQR4_RESERVED, bits); #endif bits = adc_sqrbits(priv, ADC_SQR3_FIRST, ADC_SQR3_LAST, ADC_SQR3_SQ_OFFSET); adc_modifyreg(priv, STM32_ADC_SQR3_OFFSET, ~ADC_SQR3_RESERVED, bits); bits = adc_sqrbits(priv, ADC_SQR2_FIRST, ADC_SQR2_LAST, ADC_SQR2_SQ_OFFSET); adc_modifyreg(priv, STM32_ADC_SQR2_OFFSET, ~ADC_SQR2_RESERVED, bits); bits = ((uint32_t)priv->nchannels - 1) << ADC_SQR1_L_SHIFT | adc_sqrbits(priv, ADC_SQR1_FIRST, ADC_SQR1_LAST, ADC_SQR1_SQ_OFFSET); adc_modifyreg(priv, STM32_ADC_SQR1_OFFSET, ~ADC_SQR1_RESERVED, bits); return OK; } /**************************************************************************** * Name: adc_ioctl * * Description: * All ioctl calls will be routed through this method. * * Input Parameters: * dev - pointer to device structure used by the driver * cmd - command * arg - arguments passed with command * * Returned Value: * ****************************************************************************/ static int adc_ioctl(FAR struct adc_dev_s *dev, int cmd, unsigned long arg) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; int ret = OK; switch (cmd) { case ANIOC_TRIGGER: adc_startconv(priv, true); break; #ifdef CONFIG_STM32_STM32L15XX case IO_ENABLE_TEMPER_VOLT_CH: adc_ioc_enable_tvref_register(dev, *(bool *)arg); break; case IO_ENABLE_DISABLE_PDI: case IO_ENABLE_DISABLE_PDD: case IO_ENABLE_DISABLE_PDD_PDI: adc_ioc_change_sleep_between_opers(dev, cmd, *(bool *)arg); break; case IO_ENABLE_DISABLE_AWDIE: case IO_ENABLE_DISABLE_EOCIE: case IO_ENABLE_DISABLE_JEOCIE: case IO_ENABLE_DISABLE_OVRIE: case IO_ENABLE_DISABLE_ALL_INTS: adc_ioc_change_ints(dev, cmd, *(bool *)arg); break; case IO_START_CONV: { uint8_t ch = ((uint8_t)arg); ret = adc_ioc_wait_rcnr_zeroed(priv); if (ret < 0) { set_errno(-ret); return ret; } ret = adc_set_ch(dev, ch); if (ret < 0) { set_errno(-ret); return ret; } if (ch) { /* Clear fifo */ dev->ad_recv.af_head = 0; dev->ad_recv.af_tail = 0; } adc_startconv(priv, true); } break; #if STM32_CFGR_PLLSRC != 0 || STM32_SYSCLK_SW != RCC_CFGR_SW_HSI case IO_STOP_ADC: adc_enable(priv, false); adc_enable_hsi(false); break; case IO_START_ADC: adc_enable_hsi(true); adc_enable(priv, true); break; #endif #endif /* CONFIG_STM32_STM32L15XX */ default: aerr("ERROR: Unknown cmd: %d\n", cmd); ret = -ENOTTY; break; } return ret; } /**************************************************************************** * Name: adc_interrupt * * Description: * Common ADC interrupt handler. * * Input Parameters: * * Returned Value: * ****************************************************************************/ static int adc_interrupt(FAR struct adc_dev_s *dev) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; uint32_t regval; uint32_t pending; int32_t data; regval = adc_getreg(priv, STM32_ADC_ISR_OFFSET); pending = regval & ADC_ISR_ALLINTS; if (pending == 0) { return OK; } /* Identifies the interruption AWD, OVR or EOC */ if ((regval & ADC_ISR_AWD) != 0) { awarn("WARNING: Analog Watchdog, Value converted out of range!\n"); } if ((regval & ADC_ISR_OVR) != 0) { awarn("WARNING: Overrun has occurred!\n"); } /* EOC: End of conversion */ if ((regval & ADC_ISR_EOC) != 0) { /* Read the converted value and clear EOC bit * (It is cleared by reading the ADC_DR) */ data = adc_getreg(priv, STM32_ADC_DR_OFFSET) & ADC_DR_RDATA_MASK; /* Verify that the upper-half driver has bound its callback functions */ if (priv->cb != NULL) { /* Give the ADC data to the ADC driver. The ADC receive() method * accepts 3 parameters: * * 1) The first is the ADC device instance for this ADC block. * 2) The second is the channel number for the data, and * 3) The third is the converted data for the channel. */ DEBUGASSERT(priv->cb->au_receive != NULL); priv->cb->au_receive(dev, priv->chanlist[priv->current], data); } /* Set the channel number of the next channel that will complete * conversion. */ priv->current++; if (priv->current >= priv->nchannels) { /* Restart the conversion sequence from the beginning */ priv->current = 0; } } /* by MR regval &= ~pending; */ /* by MR adc_putreg(priv, STM32_ADC_ISR_OFFSET, regval); adc_putreg(priv, STM32_ADC_ISR_OFFSET, pending); */ return OK; } /**************************************************************************** * Name: adc1_interrupt * * Description: * ADC interrupt handler for the STM32 L15XX family. * * Input Parameters: * irq - The IRQ number that generated the interrupt. * context - Architecture specific register save information. * * Returned Value: * ****************************************************************************/ #if defined(STM32_IRQ_ADC1) static int adc1_interrupt(int irq, FAR void *context, FAR void *arg) { adc_interrupt(&g_adcdev1); return OK; } #endif /**************************************************************************** * Name: adc12_interrupt * * Description: * ADC1/2 interrupt handler for the STM32 F1/F3 families. * * Input Parameters: * * Returned Value: * ****************************************************************************/ #if defined(STM32_IRQ_ADC12) && \ (defined(CONFIG_STM32_ADC1) || defined(CONFIG_STM32_ADC2)) static int adc12_interrupt(int irq, FAR void *context, FAR void *arg) { #ifdef CONFIG_STM32_ADC1 adc_interrupt(&g_adcdev1); #endif #ifdef CONFIG_STM32_ADC2 adc_interrupt(&g_adcdev2); #endif return OK; } #endif /**************************************************************************** * Name: adc3_interrupt * * Description: * ADC3 interrupt handler for the STM32 F1 family. * * Input Parameters: * * Returned Value: * ****************************************************************************/ #if defined(STM32_IRQ_ADC3) && defined(CONFIG_STM32_ADC3) static int adc3_interrupt(int irq, FAR void *context, FAR void *arg) { adc_interrupt(&g_adcdev3); return OK; } #endif /**************************************************************************** * Name: adc4_interrupt * * Description: * ADC4 interrupt handler for the STM32 F3 family. * * Input Parameters: * * Returned Value: * ****************************************************************************/ #if defined(STM32_IRQ_ADC4) && defined(CONFIG_STM32_ADC4) static int adc4_interrupt(int irq, FAR void *context, FAR void *arg) { adc_interrupt(&g_adcdev4); return OK; } #endif /**************************************************************************** * Name: adc123_interrupt * * Description: * ADC1/2/3 interrupt handler for the STM32 F2/F4 families. * * Input Parameters: * * Returned Value: * ****************************************************************************/ #if defined(STM32_IRQ_ADC) static int adc123_interrupt(int irq, FAR void *context, FAR void *arg) { #ifdef CONFIG_STM32_ADC1 adc_interrupt(&g_adcdev1); #endif #ifdef CONFIG_STM32_ADC2 adc_interrupt(&g_adcdev2); #endif #ifdef CONFIG_STM32_ADC3 adc_interrupt(&g_adcdev3); #endif return OK; } #endif /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: adc_change_sample_time * * Description: * Changes sample times for specified channels. This method * doesn't make any register writing. So, it's only stores the information. * Values provided by user will be written in registers only on the next * ADC peripheral start, as it was told to do in manual. However, before * very first start, user can call this method and override default values * either for every channels or for only some predefined by user channel(s) * * Input Parameters: * priv - pointer to the adc device structure * pdi_high - true: The ADC is powered down when waiting for a start event * false: The ADC is powered up when waiting for a start event * * Returned Value: * None * ****************************************************************************/ #ifdef CONFIG_STM32_STM32L15XX void stm32_adcchange_sample_time(FAR struct adc_dev_s *dev, FAR struct adc_sample_time_s *time_samples) { FAR struct stm32_dev_s *priv = (FAR struct stm32_dev_s *)dev->ad_priv; uint8_t ch_index; uint8_t i; /* Check if user wants to assign the same value for all channels * or just wants to change sample time values for certain channels */ if (time_samples->all_same) { memset(priv->sample_rate, time_samples->all_ch_sample_time, ADC_CHANNELS_NUMBER); } else { for (i = 0; i < time_samples->channels_nbr; i++) { ch_index = time_samples->channel->channel; if (ch_index >= ADC_CHANNELS_NUMBER) { break; } priv->sample_rate[ch_index] = time_samples->channel->sample_time; } } } #endif /**************************************************************************** * Name: stm32_adcinitialize * * Description: * Initialize the ADC. * * The logic is, save nchannels : # of channels (conversions) in ADC_SQR1_L * Then, take the chanlist array and store it in the SQR Regs, * chanlist[0] -> ADC_SQR3_SQ1 * chanlist[1] -> ADC_SQR3_SQ2 * ... * chanlist[15]-> ADC_SQR1_SQ16 * * up to * chanlist[nchannels] * * Input Parameters: * intf - Could be {1,2,3} for ADC1, ADC2, or ADC3 * chanlist - The list of channels * cchannels - Number of channels * * Returned Value: * Valid ADC device structure reference on succcess; a NULL on failure * ****************************************************************************/ struct adc_dev_s *stm32_adcinitialize(int intf, FAR const uint8_t *chanlist, int cchannels) { FAR struct adc_dev_s *dev; FAR struct stm32_dev_s *priv; ainfo("intf: %d cchannels: %d\n", intf, cchannels); switch (intf) { #ifdef CONFIG_STM32_ADC1 case 1: ainfo("ADC1 selected\n"); dev = &g_adcdev1; break; #endif #ifdef CONFIG_STM32_ADC2 case 2: ainfo("ADC2 selected\n"); dev = &g_adcdev2; break; #endif #ifdef CONFIG_STM32_ADC3 case 3: ainfo("ADC3 selected\n"); dev = &g_adcdev3; break; #endif #ifdef CONFIG_STM32_ADC4 case 4: ainfo("ADC4 selected\n"); dev = &g_adcdev4; break; #endif default: aerr("ERROR: No ADC interface defined\n"); return NULL; } /* Configure the selected ADC */ priv = (FAR struct stm32_dev_s *)dev->ad_priv; #if defined(CONFIG_STM32_STM32L15XX) /* Assign default values for the sample time table */ memset(priv->sample_rate, ADC_SMPR_DEFAULT, ADC_CHANNELS_NUMBER); #endif DEBUGASSERT(cchannels <= ADC_MAX_SAMPLES); priv->cb = NULL; priv->cchannels = cchannels; memcpy(priv->chanlist, chanlist, cchannels); return dev; } #endif /* CONFIG_STM32_STM32F10XX || CONFIG_STM32_STM32F20XX || * CONFIG_STM32_STM32F30XX || CONFIG_STM32_STM32F33XX || * CONFIG_STM32_STM32F47XX || CONFIG_STM32_STM32F40XX || * CONFIG_STM32_STM32L15XX */ #endif /* CONFIG_STM32_ADC1 || CONFIG_STM32_ADC2 || * CONFIG_STM32_ADC3 || CONFIG_STM32_ADC4 */ #endif /* CONFIG_STM32_ADC */