sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
bug/duktape-crash-ctrl-c
nuttx/drivers/contactless/mfrc522.h
raiden00pl 6c5f8bd61f drivers/contactless: fix gcc14 errors
2024-06-13 02:21:29 +08:00

423 lines
24 KiB
C
Raw Permalink Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/****************************************************************************
* drivers/contactless/mfrc522.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __DRIVERS_CONTACTLESS_MFRC522_H
#define __DRIVERS_CONTACTLESS_MFRC522_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <nuttx/spi/spi.h>
#include <nuttx/wqueue.h>
/****************************************************************************
* Pre-Processor Definitions
****************************************************************************/
/* The commands used by the PCD to manage communication with several PICCs
* (ISO 14443-3, Type A, section 6.4)
*/
#define PICC_CMD_REQA 0x26 /* REQuest command, Type A */
#define PICC_CMD_WUPA 0x52 /* Wake-UP command, Type A */
#define PICC_CMD_CT 0x88 /* Cascade Tag, used during anti collision. */
#define PICC_CMD_SEL_CL1 0x93 /* Anti collision/Select, Cascade Level 1 */
#define PICC_CMD_SEL_CL2 0x95 /* Anti collision/Select, Cascade Level 2 */
#define PICC_CMD_SEL_CL3 0x97 /* Anti collision/Select, Cascade Level 3 */
#define PICC_CMD_HLTA 0x50 /* HaLT command, Type A */
/* The commands used for MIFARE Classic
* (from http://www.mouser.com/ds/2/302/MF1S503x-89574.pdf, Section 9)
* Use PCD_MFAuthent to authenticate access to a sector, then use these
* commands to read/write/modify the blocks on the sector.
* The read/write commands can also be used for MIFARE Ultralight.
*/
#define PICC_CMD_MF_AUTH_KEY_A 0x60 /* Perform authentication with Key A */
#define PICC_CMD_MF_AUTH_KEY_B 0x61 /* Perform authentication with Key B */
#define PICC_CMD_MF_READ 0x30 /* Reads one 16 byte block from auth sector */
#define PICC_CMD_MF_WRITE 0xA0 /* Writes one 16 byte block to auth senctor */
#define PICC_CMD_MF_DECREMENT 0xC0 /* Decrements contents of a block */
#define PICC_CMD_MF_INCREMENT 0xC1 /* Increments contents of a block */
#define PICC_CMD_MF_RESTORE 0xC2 /* Reads the contents of a block */
#define PICC_CMD_MF_TRANSFER 0xB0 /* Writes the contents of a block */
/* The commands used for MIFARE Ultralight
* (from http://www.nxp.com/documents/data_sheet/MF0ICU1.pdf, Section 8.6)
* The PICC_CMD_MF_READ/_MF_WRITE can also be used for MIFARE Ultralight.
*/
#define PICC_CMD_UL_WRITE 0xA2 /* Writes one 4 byte page to the PICC. */
/* MFRC522 Registers */
/* NOTE: All SPI addresses are shifted one bit left in the SPI address byte
* See section 8.1.2.3 from MFRC522 datasheet
*/
/* Page 0: Commands and status */
/* 0x00 - reserved for future use */
#define MFRC522_COMMAND_REG (0x01 << 1) /* starts/stops command execution */
#define MFRC522_COM_IEN_REG (0x02 << 1) /* dis/enable int. req. ctrl bits */
#define MFRC522_DIV_IEN_REG (0x03 << 1) /* dis/enable int. req. ctrl bits */
#define MFRC522_COM_IRQ_REG (0x04 << 1) /* interrupt request bits */
#define MFRC522_DIV_IRQ_REG (0x05 << 1) /* interrupt request bits */
#define MFRC522_ERROR_REG (0x06 << 1) /* error bits status of last cmd */
#define MFRC522_STATUS1_REG (0x07 << 1) /* communication status bits */
#define MFRC522_STATUS2_REG (0x08 << 1) /* rcvr and transmitter status */
#define MFRC522_FIFO_DATA_REG (0x09 << 1) /* input/output of FIFO buffer */
#define MFRC522_FIFO_LEVEL_REG (0x0A << 1) /* number of bytes stored in the FIFO */
#define MFRC522_WATER_LEVEL_REG (0x0B << 1) /* level for FIFO under/overflow */
#define MFRC522_CONTROL_REG (0x0C << 1) /* miscellaneos control register */
#define MFRC522_BIT_FRAMING_REG (0x0D << 1) /* adjustments for bit-oriented frames */
#define MFRC522_COLL_REG (0x0E << 1) /* bit position of first bit-collision detected */
/* 0x0F - reserved for future use */
/* Page 1: Commands */
/* 0x10 - reserved for future use */
#define MFRC522_MODE_REG (0x11 << 1) /* defines general modes for transmit/receive */
#define MFRC522_TX_MODE_REG (0x12 << 1) /* defines transmission data rate and framing */
#define MFRC522_RX_MODE_REG (0x13 << 1) /* defines reception data rate and framing */
#define MFRC522_TX_CTRL_REG (0x14 << 1) /* controls antenna driver pins TX1 and TX2 */
#define MFRC522_TX_ASK_REG (0x15 << 1) /* controls the setting of transmission modulation */
#define MFRC522_TX_SEL_REG (0x16 << 1) /* selects the internal sources for antenna driver */
#define MFRC522_RX_SEL_REG (0x17 << 1) /* selects the internal receiver settings */
#define MFRC522_RX_THLD_REG (0x18 << 1) /* selects the thresholds for bit decoder */
#define MFRC522_DEMOD_REG (0x19 << 1) /* defines demodulator settings */
/* 0x1A - reserved for future use */
/* 0x1B - reserved for future use */
#define MFRC522_MF_TX_REG (0x1C << 1) /* controls some MIFARE comm tx param */
#define MFRC522_MF_RX_REG (0x1D << 1) /* controls some MIFARE comm rx param */
/* 0x1E - reserved for future use */
#define MFRC522_SERIAL_SPD_REG (0x1F << 1) /* selects the speed of the serial UART */
/* Page 2: Configuration */
/* 0x20 - reserved for future use */
#define MFRC522_CRC_RESULT_REGH (0x21 << 1) /* shows the MSB values of CRC calc. */
#define MFRC522_CRC_RESULT_REGL (0x22 << 1) /* shows the LSB values of CRC calc. */
/* 0x23 - reserved for future use */
#define MFRC522_MOD_WIDTH_REG (0x24 << 1) /* controls the ModWidth setting */
/* 0x25 - reserved for future use */
#define MFRC522_RF_CFG_REG (0x26 << 1) /* configures the receiver gain */
#define MFRC522_GSN_REG (0x27 << 1) /* selects the conductance of n-driver TX1/2 */
#define MFRC522_CW_GSP_REG (0x28 << 1) /* defines the conductance of p-driver during no modulation */
#define MFRC522_MOD_GSP_REG (0x29 << 1) /* defines the conductance of p-driver during modulation */
#define MFRC522_TMODE_REG (0x2A << 1) /* defines settings for the internal timer */
#define MFRC522_TPRESCALER_REG (0x2B << 1) /* the lower 8 bits of TPrescaler value */
#define MFRC522_TRELOAD_REGH (0x2C << 1) /* defines the 16-bit timer reload value */
#define MFRC522_TRELOAD_REGL (0x2D << 1) /* defines the 16-bit timer reload value */
#define MFRC522_TCOUNT_VAL_REGH (0x2E << 1) /* shows the 16-bit timer value */
#define MFRC522_TCOUNT_VAL_REGL (0x2F << 1) /* shows the 16-bit timer value */
/* Page 3: Test Registers */
/* 0x30 - reserved for future use */
#define MFRC522_TEST_SEL1_REG (0x31 << 1) /* general test signal configuration */
#define MFRC522_TEST_SEL2_REG (0x32 << 1) /* general test signal configuration */
#define MFRC522_TEST_PIN_EN_REG (0x33 << 1) /* enables pin output driver on pins D1 to D7 */
#define MFRC522_TEST_PIN_VAL_REG (0x34 << 1) /* defines the values to D1 to D7 */
#define MFRC522_TEST_BUS_REG (0x35 << 1) /* shows the status of the internal test bus */
#define MFRC522_AUTOTEST_REG (0x36 << 1) /* controls the digital self test */
#define MFRC522_VERSION_REG (0x37 << 1) /* shows the software version */
#define MFRC522_ANALOG_TEST_REG (0x38 << 1) /* controls the pins AUX1 and AUX2 */
#define MFRC522_TEST_DAC1_REG (0x39 << 1) /* defines the test value for TestDAC1 */
#define MFRC522_TEST_DAC2_REG (0x3A << 1) /* defines the test value for TestDAC2 */
#define MFRC522_TEST_ADC_REG (0x3B << 1) /* show the value of ADC I and Q channels */
/* Section 9.3.1.2: MFRC522 Command Register */
#define MFRC522_CMD_MASK 0x0F
# define MFRC522_IDLE_CMD 0x00 /* no action, cancels current command execution */
# define MFRC522_MEM_CMD 0x01 /* stores 25 bytes into the internal buffer */
# define MFRC522_GEN_RND_ID_CMD 0x02 /* generates a 10-bytes random ID number */
# define MFRC522_CALC_CRC_CMD 0x03 /* activates the CRC coprocessor or self test */
# define MFRC522_TRANSMIT_CMD 0x04 /* transmits data from the FIFO buffer */
# define MFRC522_NO_CHANGE_CMD 0x07 /* no command change, used to modify CommandReg */
# define MFRC522_RECEIVE_CMD 0x08 /* activates the receiver circuits */
# define MFRC522_TRANSCV_CMD 0x0C /* transmits data from FIFO and receive automatically */
# define MFRC522_MF_AUTH_CMD 0x0E /* performs the MIFARE stand authentication as a reader */
# define MFRC522_SOFTRST_CMD 0x0F /* resets the MFRC522 */
#define MFRC522_POWER_DOWN (1 << 4) /* soft power-down mode entered */
#define MFRC522_RCV_OFF (1 << 5) /* turns off analog part of receiver */
/* Section 9.3.1.3: ComIEnReg register */
#define MFRC522_TIMER_IEN (1 << 0) /* allows the timer interrupt request on pin IRQ */
#define MFRC522_ERR_IEN (1 << 1) /* allows the error interrupt request on pin IRQ */
#define MFRC522_LO_ALERT_IEN (1 << 2) /* allows the low alert interrupt request on pin IRQ */
#define MFRC522_HI_ALERT_IEN (1 << 3) /* allows the high alert interrupt request on pin IRQ */
#define MFRC522_IDLE_IEN (1 << 4) /* allows the idle interrupt request on pin IRQ */
#define MFRC522_RX_IEN (1 << 5) /* allows the receiver interrupt request on pin IRQ */
#define MFRC522_TX_IEN (1 << 6) /* allows the transmitter interrupt request on pin IRQ */
#define MFRC522_IRQ_INV (1 << 7) /* signal on pin IRQ is inverse of IRq bit from Status1Reg */
/* Section 9.3.1.4: DivIEnReg register */
#define MFRC522_CRC_IEN (1 << 2) /* allows the CRC interrupt request on pin IRQ */
#define MFRC522_MFIN_ACT_IEN (1 << 4) /* allows the MFIN active interrupt request on pin IRQ */
#define MFRC522_IRQ_PUSH_PULL (1 << 7) /* 1 = IRQ pin is a standard CMOS output pin, 0 = open-drain */
/* Section 9.3.1.5: ComIrqReg register */
#define MFRC522_COM_IRQ_MASK (0x7F)
#define MFRC522_TIMER_IRQ (1 << 0) /* enabled when TCounterValReg reaches value 0 */
#define MFRC522_ERR_IRQ (1 << 1) /* any error bit in the ErrorReg register is set */
#define MFRC522_LO_ALERT_IRQ (1 << 2) /* Status1Reg register’s LoAlert bit is set */
#define MFRC522_HI_ALERT_IRQ (1 << 3) /* Status1Reg register’s HiAlert bit is set */
#define MFRC522_IDLE_IRQ (1 << 4) /* if a command terminates this bit is set */
#define MFRC522_RX_IRQ (1 << 5) /* receiver has detected the end of a valid data stream */
#define MFRC522_TX_IRQ (1 << 6) /* set immediately after the last data bit was transmitted */
#define MFRC522_SET1 (1 << 7) /* indicate the status of ComIrqReg bits */
/* Section 9.3.1.6: DivIrqReg register */
#define MFRC522_CRC_IRQ (1 << 2) /* the CalcCRC command is active and all data is processed */
#define MFRC522_MFIN_ACT_IRQ (1 << 4) /* MFIN is active, int is set on rising/falling signal edge */
#define MFRC522_SET2 (1 << 7) /* indicates the status of the marked bits in the DivIrqReg */
/* Section 9.3.1.7: ErrorReg register */
#define MFRC522_PROTO_ERR (1 << 0) /* set if the SOF is incorrect or during MFAuthent if data is incorrect */
#define MFRC522_PARITY_ERR (1 << 1) /* parity check failed */
#define MFRC522_CRC_ERR (1 << 2) /* the RxCRCEn bit is set and the CRC calculation fails */
#define MFRC522_COLL_ERR (1 << 3) /* a bit-collision is detected */
#define MFRC522_BUF_OVFL_ERR (1 << 4) /* FIFO is full and the host or internal state machine try to write data */
#define MFRC522_TEMP_ERR (1 << 6) /* internal temperature sensor detects overheating */
#define MFRC522_WR_ERR (1 << 7) /* data write error in the FIFO, host writing to FIFO at the wrong time */
/* Section 9.3.1.8: Status1Reg register */
#define MFRC522_LO_ALERT (1 << 0) /* number of bytes on FIFO lower than the water-mark */
#define MFRC522_HI_ALERT (1 << 1) /* number of bytes on FIFO higher than the water-mark */
#define MFRC522_TRUNNING (1 << 3) /* timer is running */
#define MFRC522_IRQ (1 << 4) /* indicates if any interrupt source requests attention */
#define MFRC522_CRC_READY (1 << 5) /* the CRC calculation has finished */
#define MFRC522_CRC_OK (1 << 6) /* when the calculation is done correctly this bit change to 1 */
/* Section 9.3.1.9: Status2Reg register */
#define MFRC522_MODEM_STATE_MASK (7 << 0) /* shows the state of the transmitter and receiver state machine */
#define MFRC522_MODEM_IDLE (0) /* idle */
#define MFRC522_MODEM_WAIT_BFR (1) /* wait for the BitFramingReg register’s StartSend bit */
#define MFRC522_MODEM_TXWAIT (2) /* wait until RF field is present if TxWaitRF bit is set to 1 */
#define MFRC522_MODEM_TXING (3) /* transmitting */
#define MFRC522_MODEM_RXWAIT (4) /* wait until RF field is present if TxWaitRF bit is set to 1 */
#define MFRC522_MODEM_WAIT_DATA (5) /* wait for data */
#define MFRC522_MODEM_RXING (6) /* receiving */
#define MFRC522_MF_CRYPTO1_ON (1 << 3) /* MIFARE Crypto1 unit is switched on */
#define MFRC522_I2C_FORCE_HS (1 << 6) /* set the I2C to high-speed mode (R/W bit) */
#define MFRC522_TEMP_SENS_CLEAR (1 << 7) /* clears the temperature error if it is below 125C (R/W bit) */
/* Section 9.3.1.10: FIFODataReg register */
#define MFRC522_FIFO_DATA_MASK (0xFF) /* Input and output of 64 byte FIFO buffer */
/* Section 9.3.1.11: FIFOLevelReg register */
#define MFRC522_FIFOLEVEL_MASK (0x7F) /* indicates the number of bytes stored in the FIFO buffer */
#define MFRC522_FLUSH_BUFFER (1 << 7) /* immediately clears the internal FIFO buffer */
/* Section 9.3.1.12: WaterLevelReg register */
#define MFRC522_WATER_LEVEL_MASK (0x3F) /* level for FIFO under- and overflow warning */
/* Section 9.3.1.13: ControlReg register */
#define MFRC522_RX_LAST_BITS_MASK (7 << 0) /* indicates the number of valid bits in the last received byte */
#define MFRC522_TSTART_NOW (1 << 6) /* timer starts immediately */
#define MFRC522_TSTOP_NOW (1 << 7) /* timer stops immediately */
/* Section 9.3.1.14: BitFramingReg register */
#define MFRC522_TX_LAST_BITS_MASK (7 << 0) /* defines the number of bits of the last byte that will be transmitted */
#define MFRC522_RX_ALIGN_MASK (7 << 4) /* used for reception of bit-oriented frames */
#define MFRC522_START_SEND (1 << 7) /* starts the transmission of data */
/* Section 9.3.1.15: CollReg register */
#define MFRC522_COLL_POS_MASK (0x1F) /* shows the bit position of the first detected collision */
#define MFRC522_COLL_POS_NOT_VALID (1 << 5) /* no collision detected or it is out of the range of CollPos[4:0] */
#define MFRC522_VALUES_AFTER_COLL (1 << 7) /* 0 means: all received bits will be cleared after a collision */
/* Section 9.3.2.2: ModeReg register */
#define MFRC522_CRC_PRESET_MASK (0x3) /* defines the preset value for the CalcCRC */
#define MFRC522_CRC_PRESET_0000 (0x0) /* 0000h CRC preset value */
#define MFRC522_CRC_PRESET_6363 (0x1) /* 6363h CRC preset value */
#define MFRC522_CRC_PRESET_A671 (0x2) /* A671h CRC preset value */
#define MFRC522_CRC_PRESET_FFFF (0x3) /* FFFFh CRC preset value */
#define MFRC522_POL_MFIN (1 << 3) /* defines the polarity of pin MFIN */
#define MFRC522_TX_WAIT_RF (1 << 5) /* transmitter can only be started if an RF field is generated */
#define MFRC522_MSB_FIRST (1 << 7) /* CRC coprocessor calculates the CRC with MSB first */
/* Section 9.3.2.3: TxModeReg register */
#define MFRC522_INV_MOD (1 << 3) /* modulation of transmitted data is inverted */
#define MFRC522_TX_SPEED_MASK (7 << 4) /* defines the bit rate during data transmission */
#define MFRC522_TX_106KBD (0 << 4) /* 106 kBd */
#define MFRC522_TX_212KBD (1 << 4) /* 212 kBd */
#define MFRC522_TX_424KBD (2 << 4) /* 424 kBd */
#define MFRC522_TX_848KBD (3 << 4) /* 848 kBd */
/* 4-7 << 4 - reserved */
#define MFRC522_TX_CRC_EN (1 << 7) /* enables CRC generation during data transmission */
/* Section 9.3.2.4: RxModeReg register */
#define MFRC522_RX_MULTIPLE (1 << 2) /* enable to receive more than one data frame, only at 106kBd */
#define MFRC522_RX_NO_ERR (1 << 3) /* ignore invalid data stream error (less than 4 bits received) */
#define MFRC522_RX_SPEED_MASK (7 << 4) /* defines the bit rate during data reception */
#define MFRC522_RX_106KBD (0 << 4) /* 106 kBd */
#define MFRC522_RX_212KBD (1 << 4) /* 212 kBd */
#define MFRC522_RX_424KBD (2 << 4) /* 424 kBd */
#define MFRC522_RX_848KBD (3 << 4) /* 848 kBd */
/* 4-7 << 4 - reserved */
#define MFRC522_RX_CRC_EN (1 << 7) /* enables CRC generation during data reception */
/* Section 9.3.2.5: TxControlReg register */
#define MFRC522_TX1_RF_EN (1 << 0) /* output signal on pin TX1 delivers 13.56MHz */
#define MFRC522_TX2_RF_EN (1 << 1) /* output signal on pin TX2 delivers 13.56MHz */
/* bit 2 - reserved */
#define MFRC522_TX2_CW (1 << 3) /* output signal on pin TX2 delivers (un)modulated 13.56MHz */
#define MFRC522_INV_TX1_RF_OFF (1 << 4) /* output signal on pin TX1 is inverted when driver TX1 is disabled */
#define MFRC522_INV_TX2_RF_OFF (1 << 5) /* output signal on pin TX2 is inverted when driver TX2 is disabled */
#define MFRC522_INV_TX1_RF_ON (1 << 6) /* output signal on pin TX1 is inverted when driver TX1 is enabled */
#define MFRC522_INV_TX2_RF_ON (1 << 7) /* output signal on pin TX2 is inverted when driver TX2 is enabled */
/* Section 9.3.2.6: TxASKReg register */
#define MFRC522_FORCE_100ASK (1 << 6) /* forces a 100% ASK modulation independent of the ModGsPReg setting */
/* Section 9.3.2.7: TxSelReg register */
#define MFRC522_MFOUT_SEL_MASK (0xF) /* selects the input for pin MFOUT */
#define MFRC522_MFOUT_3STATE (0) /* 3-state */
#define MFRC522_MFOUT_LOW (1) /* constant Low */
#define MFRC522_MFOUT_HIGH (2) /* constant High */
#define MFRC522_MFOUT_TEST_BUS (3) /* test bus signal as defined by the TstBusBitSel[2:0] value */
#define MFRC522_MFOUT_INT_ENV (4) /* modulation signal (envelope) from the internal encoder */
#define MFRC522_MFOUT_TX_STREAM (5) /* serial data stream to be transmitted, data stream before Miller encoder */
/* 6 - reserved */
#define MFRC522_MFOUT_RX_STREAM (7) /* serial data stream received, data stream after Manchester decoder */
/* 8-15 - reserved */
#define MFRC522_DRV_SEL_MASK (3 << 4) /* selects the input of drivers TX1 and TX2 */
#define MFRC522_DRV_SEL_3STATE (0 << 4) /* 3-state */
#define MFRC522_DRV_SEL_INT_ENV (1 << 4) /* modulation signal (envelope) from the internal encoder */
#define MFRC522_DVR_SEL_ENV_MFIN (2 << 4) /* modulation signal (envelope) from pin MFIN */
#define MFRC522_DVR_SEL_HIGH (3 << 4) /* High: depends on InvTx1RFOn/InvTx1RFOff and InvTx2RFOn/InvTx2RFOff */
/* Section 9.3.2.8: RxSelReg register */
#define MFRC522_RX_WAIT_MASK (0x3F) /* delay the receiver RxWait bit-clocks after transmission */
#define MFRC522_UART_SEL_MASK (3 << 6) /* selects the input of the contactless UART */
#define MFRC522_UART_LOW (0 << 6) /* constant Low */
#define MFRC522_UART_MANCHESTER (1 << 6) /* Manchester with subcarrier from pin MFIN */
#define MFRC522_UART_INT_MOD (2 << 6) /* modulated signal from the internal analog module, default */
#define MFRC522_UART_NRZ_CODE (3 << 6) /* NRZ coding without subcarrier from pin MFIN */
/* Section 9.3.2.9: RxThresholdReg register */
#define MFRC522_COLL_LEVEL_MASK (7) /* the minimum signal strength to generate a bit-collision */
#define MFRC522_MIN_LEVEL_MASK (0xF << 4) /* the minimum signal strength that will be accepted */
/* Section 9.3.2.10: DemodReg register */
#define MFRC522_TAU_SYNC_MASK (3 << 0) /* changes the time-constant of the internal PLL during burst */
#define MFRC522_TAU_RCV_MASK (3 << 2) /* changes the time-constant of the internal PLL during data reception */
#define MFRC522_TPRESCAL_EVEN (1 << 4) /* defines the Timer Prescaler formula to use */
#define MFRC522_FIX_IQ (1 << 5) /* defines if reception will be fixed at channel I or Q based on AddIQ[1:0] */
#define MFRC522_ADD_IQ_MASK (3 << 6) /* defines the use of I and Q channel during reception */
/* Section 9.3.2.13: MfTxReg register */
#define MFRC522_MF_TX_WAIT_MASK (3 << 0) /* defines the additional response time */
/* Section 9.3.2.14 MfRxReg register */
#define MFRC522_MF_RX_PARITY_DIS (1 << 4 ) /* disable parity bit to transmission and reception */
/* Section 9.3.2.16: SerialSpeedReg register */
#define MFRC522_BR_T1_MASK (0x1F) /* factor BR_T1 adjusts the transfer speed */
#define MFRC522_BR_T0_MASK (7 << 5) /* factor BR_T0 adjusts the transfer speed */
/* Section 9.3.3.6: RFCfgReg register */
#define MFRC522_RX_GAIN_MASK (0x7 << 4)
#define MFRC522_RX_GAIN_18DB (0x0 << 4)
#define MFRC522_RX_GAIN_23DB (0x1 << 4)
#define MFRC522_RX_GAIN_18DB_2 (0x2 << 4)
#define MFRC522_RX_GAIN_23DB_2 (0x3 << 4)
#define MFRC522_RX_GAIN_33DB (0x4 << 4)
#define MFRC522_RX_GAIN_38DB (0x5 << 4)
#define MFRC522_RX_GAIN_43DB (0x6 << 4)
#define MFRC522_RX_GAIN_48DB (0x7 << 4)
/* MFRC522 TModeReg and TPrescalerReg registers */
#define MFRC522_TPRESCALER_HI_MASK (0xF)
#define MFRC522_TAUTO_RESTART (1 << 4)
#define MFRC522_TGATED_MASK (3 << 5)
#define MFRC522_TGATED_NONGATED (0 << 5) /* non-gated mode */
#define MFRC522_TGATED_MFIN (1 << 5) /* gated by pin MFIN */
#define MFRC522_TGATED_AUX1 (2 << 5) /* gated by pin AUX1 */
#define MFRC522_TAUTO (1 << 7) /* timer starts automatically at the end of the transmission */
/* MFRC522 AutoTestReg register */
#define MFRC522_SELFTEST_MASK (0xF) /* for default operation the self test must be disabled by value 0000b */
#define MFRC522_RFT_MASK (3 << 4) /* reserved for production tests */
#define MFRC522_AMP_RCV (1 << 6) /* non-linear signal processing mode, increase range distance at 106kBd */
#define MFRC522_SELFTEST_EN 9 /* the self test is enabled by value 1001b */
#ifndef CONFIG_MFRC522_SPI_FREQ
# define CONFIG_MFRC522_SPI_FREQ (5000000)
#endif
/****************************************************************************
* Public Types
****************************************************************************/
struct mfrc522_dev_s
{
uint8_t state;
uint8_t pm_level;
FAR struct spi_dev_s *spi; /* SPI interface */
};
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
bool mfrc522_set_config(struct mfrc522_dev_s *dev, uint8_t flags);
#endif /* __DRIVERS_CONTACTLESS_MFRC522_H */
Reference in New Issue View Git Blame Copy Permalink