README
^^^^^^
README for NuttX port to NXP's PNEV5180B, which is a development board
containing a NXP-LPC1769 MCU and a PN5180 NFC Frontend.
Contents
^^^^^^^^
NXP's PNEV5180B Board
Configurations
NXP's PNEV5180B Board
^^^^^^^^^^^^^^^^^^^^^
Pin Description On Board Connector
-------------------------------- ---------------- -------------
P0.2/TXD0/AD0.7 TX J201
P0.3/RXD0/AD0.6 RX
P0.22/RTS1/TD1 LD200 ORANGE LED
P0.15/TXD1/SCK0/SCK PN5180-SCK
P0.16/RXD1/SSEL0/SSEL PN5180-SSEL PN5180
P0.17/CTS1/MISO0/MISO PN5180-MISO
P0.18/DCD1/M0SI0/MOSI PN5180-MOSI
P0.19/DSR1/SDA1 EEPROM (Not Assembled)
P0.20/DTR1/SCL1 EEPROM
P0.21/RI1/RD1 PN5180-AUX2 PN5180
P0.29/USB_D+ USB-D+ USB
P0.30/USB_D- USB-D-
P2.0/PWM1.1/TXD1 LD201 RED LED
P2.5/PWM1.6/DTR1/TRACEDATA0 PN5180-nPN_RST
P2.9/USB_CONNECT/RXD2 USB_CONNECT USB
P2.11/nEINT1/I2STX_CLK PN5180-BUSY PN5180
P2.12/nEINT2/I2STX_WS PN5180-IRQ
P3.25/MAT0.0/PWM1.2 LD203 GREEN LED
P3.26/STCLK/MAT0.1/PWM1.3 LD202 BLUE LED
NXP's PNEV5180B Board
^^^^^^^^^^^^^^^^^^^^^
UART
----
Board LPC1769
Signal Pin
----------------- -----------------
TX P0.2 TXD0
RX P0.3 RXD0
USB
---
Board LPC1769
Signal Pin
----------------- -----------------
USB_CONNECT P2.9 USB_CONNECT
USB_DM P0.29 USB_D-
USB_DP P0.30 USB_D+
PN5180
------
Board LPC1769
Signal Pin
----------------- -----------------
PN5180_SCK P0.15 SCK
PN5180_SSEL P0.16 SSEL
PN5180_MISO P0.17 MISO
PN5180_MOSI P0.18 MOSI
PN5180_AUX2 P0.21 GPIO I
PN5180_nPN_RST P2.5 GPIO O
PN5180_BUSY P2.11 GPIO I
PN5180_IRQ P2.12 GPIO I
Configurations
^^^^^^^^^^^^^^
Each PNEV5180B configuration is maintained in a sub-directory and can be
selected as follow:
cd tools
./configure.sh pnev5180b:<subdir>
cd -
Where <subdir> is one of the following:
nsh:
Configures the NuttShell (nsh) located at apps/system/nsh. The
Configuration enables the serial NSH interface.
NOTES:
1. This configuration uses the mconf-based configuration tool. To
change this configurations using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
usbnsh:
Configures the NuttShell (nsh) located at apps/system/nsh. The
Configuration enables the CDC/ACM based NSH interface on /dev/ttyACM0.
nsh-cdcecm:
Configures the NuttShell (nsh) to provide a terminal on UART0. The
Configuration also provides network interface eth0 via CDC/ECM.
usbnsh-cdcecm:
This configuration includes a USB Composite Device with both CDC/ACM and
CDC/ECM. NuttShell provides a terminal via CDC/ACM. A network interface
(eth0) is also provided via CDC/ECM.
knsh:
This is identical to the nsh configuratio above except that NuttX
is built as a kernel-mode, monolithic module and the user applications
are built separately.
a2f6dc9b7c