sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
0477fb116a
nuttx/drivers/mtd/s25fl1.c
Xiang Xiao 9f027208d4 fs: Add model field to geometry and mtd_geometry_s 
the model is very useful to track the device info

Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
2023-01-31 11:50:28 -03:00

1658 lines
56 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/****************************************************************************
* drivers/mtd/s25fl1.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/* Driver for QuadSPI-based S25FL116K, S25FL132K, and S25L164K */
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <stdlib.h>
#include <unistd.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/kmalloc.h>
#include <nuttx/signal.h>
#include <nuttx/fs/ioctl.h>
#include <nuttx/spi/qspi.h>
#include <nuttx/mtd/mtd.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* QuadSPI Mode. Per data sheet, either Mode 0 or Mode 3 may be used. */
#ifndef CONFIG_S25FL1_QSPIMODE
#define CONFIG_S25FL1_QSPIMODE QSPIDEV_MODE0
#endif
/* QuadSPI Frequency per data sheet::
*
* – Normal Read (Serial):
* 50 MHz clock rate (-40°C to +85°C/105°C)
* 45 MHz clock rate (-40°C to +125°C)
* – Fast Read (Serial):
* 108 MHz clock rate (-40°C to +85°C/105°C)
* 97 MHz clock rate (-40°C to +125°C)
* – Dual Read:
* 108 MHz clock rate (-40°C to +85°C/105°C)
* 97 MHz clock rate (-40°C to +125°C)
* – Quad Read:
* 108 MHz clock rate (-40°C to +85°C/105°C)
* 97 MHz clock rate for S25FL164K (-40°C to +125°C)
*
* Table 5.8:
* - Clock frequency for all SPI commands except for Read Data
* command (0x03) and Fast Read command (0x0b): 108 MHz
* - Clock frequency for Read Data command (0x03): 50 MHz
* - Clock frequency for all Fast Read commands SIO and MIO: 108 MHz
*
* In this implementation, only "Quad" reads are performed.
*/
#ifndef CONFIG_S25FL1_QSPI_FREQUENCY
#define CONFIG_S25FL1_QSPI_FREQUENCY 108000000
#endif
/* S25FL1 Commands **********************************************************/
/* Configuration, Status, Erase, Program Commands ***************************/
/* Command Value Description: */
/* Data sequence */
#define S25FL1_READ_STATUS1 0x05 /* Read status register 1: *
* 0x05 | SR1 */
#define S25FL1_READ_STATUS2 0x35 /* Read status register 2: *
* 0x35 | SR2 */
#define S25FL1_READ_STATUS3 0x33 /* Read status register 3: *
* 0x33 | SR3 */
#define S25FL1_WRITE_ENABLE 0x06 /* Write enable: *
* 0x06 */
#define S25FL1_VWRITE_ENABLE 0x50 /* Write enable for volatile status: *
* 0x50 */
#define S25FL1_WRITE_DISABLE 0x04 /* Write disable command code: *
* 0x04 */
#define S25FL1_WRITE_STATUS 0x01 /* Write status register: *
* 0x01 | SR1 | SR2 | SR3 */
#define S25FL1_WRAP_ENABLE 0x77 /* Set Burst with Wrap: *
* 0x77 | xx | xx | xx | SR3 */
#define S25FL1_UNPROTECT_SECTOR 0x39 /* Set Block / Pointer Protection: *
* 0x39 | ADDR(MS) | ADDR(MID) | xx */
#define S25FL1_PAGE_PROGRAM 0x02 /* Page Program: *
* 0x02 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | data */
#define S25FL1_SECTOR_ERASE 0x20 /* Sector Erase (4 kB) *
* 0x02 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) */
#define S25FL1_BLOCK_ERASE 0xd8 /* Block Erase (64 kB): *
* 0x02 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) */
#define S25FL1_CHIP_ERASE_1 0x60 /* Chip Erase 1: *
* 0x60 */
#define S25FL1_CHIP_ERASE_2 0xc7 /* Chip Erase 2: *
* 0xc7 */
#define S25FL1_ERASE_PROG_SUSPEND 0x75 /* Erase / Program Suspend: *
* 0x75 */
#define S25FL1_ERASE_PROG_RESUME 0x7a /* Erase / Program Resume: *
* 0x7a */
/* Read Commands ************************************************************/
/* Command Value Description: */
/* Data sequence */
#define S25FL1_READ_DATA 0x03 /* Read Data: *
* 0x03 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | data... */
#define S25FL1_FAST_READ 0x0b /* Fast Read: *
* 0x0b | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | dummy | data... */
#define S25FL1_FAST_READ_DUAL 0x3b /* Fast Read Dual Output: *
* 0x3b | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | dummy | data... */
#define S25FL1_FAST_READ_QUAD 0x6b /* Fast Read Dual Output: *
* 0x6b | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | dummy | data... */
#define S25FL1_FAST_READ_DUALIO 0xbb /* Fast Read Dual I/O: *
* 0xbb | ADDR(MS) | ADDR(LS) | data... */
#define S25FL1_FAST_READ_QUADIO 0xeb /* Fast Read Quad I/O: *
* 0xeb | ADDR | data... */
#define S25FL1_CONT_READ_RESET 0xff /* Continuous Read Mode Reset: *
* 0xff | 0xff */
/* Reset Commands ***********************************************************/
/* Command Value Description: */
/* Data sequence */
#define S25FL1_SOFT_RESET_ENABLE 0x66 /* Software Reset Enable: *
* 0x66 */
#define S25FL1_SOFT_RESET 0x99 /* Software Reset: *
* 0x99 */
/* Continuous Read Mode Reset: *
* 0xff | 0xff */
/* ID/Security Commands *************************&***************************/
/* Command Value Description: */
/* Data sequence */
#define S25FL1_DEEP_PWRDOWN 0xb9 /* Deep Power-down: *
* 0xb9 */
#define S25FL1_RELEASE_PWRDOWN 0xab /* Release Power down / Device ID: *
* 0xab | dummy | dummy | dummy | *
* DeviceID */
#define S25FL1_MANUFACTURER 0x90 /* Manufacturer / Device ID: *
* 0x90 | dummy | dummy | 0x00 | *
* Manufacturer | DeviceID */
#define S25FL1_JEDEC_ID 0x9f /* JEDEC ID: *
* 0x9f | Manufacturer | MemoryType | *
* Capacity */
#define S25FL1_READ_SFDP 0x5a /* Read SFDP Register / Read Unique ID *
* Number: *
* 0x5a | 0x00 | 0x00 | ADDR | dummy | *
* data... */
#define S25FL1_READ_SECURITY 0x48 /* Read Security Registers: *
* 0x48 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | dummy | data... */
#define S25FL1_ERASE_SECURITY 0x44 /* Erase Security Registers: *
* 0x48 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) */
#define S25FL1_PROgRAM_SECURITY 0x42 /* Program Security Registers: *
* 0x42 | ADDR(MS) | ADDR(MID) | *
* ADDR(LS) | data... */
/* Flash Manufacturer JEDEC IDs */
#define S25FL1_JEDEC_ID_SPANSION 0x01
#define S25FL1_JEDEC_ID_ATMEL 0x1f
#define S25FL1_JEDEC_ID_ST 0x20
#define S25FL1_JEDEC_ID_SST 0xbf
#define S25FL1_JEDEC_ID_MACRONIX 0xc2
#define S25FL1_JEDEC_ID_WINBOND 0xef
/* S25FL1 JEDIC IDs */
#define S25FL1_JEDEC_DEVICE_TYPE 0x40 /* S25FL1 memory device type */
#define S25FL116K_JEDEC_CAPACITY 0x15 /* S25FL116K memory capacity */
#define S25FL132K_JEDEC_CAPACITY 0x16 /* S25FL132K memory capacity */
#define S25FL164K_JEDEC_CAPACITY 0x17 /* S25FL164K memory capacity */
/* S25FL1 Registers *********************************************************/
/* Status register bit definitions */
#define STATUS1_BUSY_MASK (1 << 0) /* Bit 0: Device ready/busy status */
#define STATUS1_READY (0 << 0) /* 0 = Not Busy */
#define STATUS1_BUSY (1 << 0) /* 1 = Busy */
#define STATUS1_WEL_MASK (1 << 1) /* Bit 1: Write enable latch status */
#define STATUS1_WEL_DISABLED (0 << 1) /* 0 = Not Write Enabled */
#define STATUS1_WEL_ENABLED (1 << 1) /* 1 = Write Enabled */
#define STATUS1_BP_SHIFT (2) /* Bits 2-4: Block protect bits */
#define STATUS1_BP_MASK (7 << STATUS1_BP_SHIFT)
#define STATUS1_BP_NONE (0 << STATUS1_BP_SHIFT)
#define STATUS1_BP_ALL (7 << STATUS1_BP_SHIFT)
#define STATUS1_TB_MASK (1 << 5) /* Bit 5: Top / Bottom Protect */
#define STATUS1_TB_TOP (0 << 5) /* 0 = BP2-BP0 protect Top down */
#define STATUS1_TB_BOTTOM (1 << 5) /* 1 = BP2-BP0 protect Bottom up */
#define STATUS1_SEC_MASK (1 << 6) /* Bit 6: Sector / Block Protect */
#define STATUS1_SEC_BLOCK (0 << 6) /* 0 = BP2-BP0 protect 64-kB blocks */
#define STATUS1_SEC_SECTOR (1 << 6) /* 1 = BP2-BP0 protect 4-kB sectors */
#define STATUS1_SRP0_MASK (1 << 7) /* Bit 7: Status register protect 0 */
#define STATUS1_SRP0_UNLOCKED (0 << 7) /* 0 = WP# no effect / PS Lock Down */
#define STATUS1_SRP0_LOCKED (1 << 7) /* 1 = WP# protect / OTP Lock Down */
#define STATUS2_SRP1_MASK (1 << 0) /* Bit 0: Status register protect 1 */
#define STATUS2_SRP1_UNLOCKED (0 << 0) /* 0 = WP# no effect / PS Lock Down */
#define STATUS2_SRP1_LOCKED (1 << 0) /* 1 = WP# protect / OTP Lock Down */
#define STATUS2_QUAD_ENABLE_MASK (1 << 1) /* Bit 1: Quad Enable */
#define STATUS2_QUAD_DISABLE (0 << 1) /* 0 = Quad Mode Not Enabled */
#define STATUS2_QUAD_ENABLE (1 << 1) /* 1 = Quad Mode Enabled */
#define STATUS2_LB_SHIFT (2) /* Bits 2-5: Security Register Lock */
#define STATUS2_LB_MASK (15 << STATUS2_LB_SHIFT)
#define STATUS2_LB_NONE (0 << STATUS2_LB_SHIFT)
#define STATUS2_LB_ALL (15 << STATUS2_LB_SHIFT)
#define STATUS2_CMP_MASK (1 << 6) /* Bit 6: Complement Protect */
#define STATUS2_CMP_NORMAL (0 << 6) /* 0 = Normal Protection Map */
#define STATUS2_CMP_INVERTED (1 << 6) /* 1 = Inverted Protection Map */
#define STATUS2_SUS_MASK (1 << 7) /* Bit 7: Suspend Status */
#define STATUS2_SUS_NONE (0 << 7) /* 0 = Erase / Program not suspended */
#define STATUS2_SUS_SUSPENDED (1 << 7) /* 1 = Erase / Program suspended */
#define STATUS3_LC_SHIFT (0) /* Bits 0-3: Latency control */
#define STATUS3_LC_MASK (15 << STATUS3_LC_SHIFT)
#define STATUS3_W4_MASK (1 << 4) /* Bit 4: Burst Wrap Enable */
#define STATUS3_W4_DISABLED (0 << 4) /* 0 = Wrap Enabled */
#define STATUS3_W4_ENABLED (1 << 4) /* 1 = Wrap Disabled */
#define STATUS3_W56_SHIFT (5) /* Bits 5-6: Burst Wrap Length */
#define STATUS3_W56_MASK (3 << STATUS3_W56_SHIFT)
#define STATUS3_W56_8BYTE (0 << STATUS3_W56_SHIFT)
#define STATUS3_W56_16BYTE (1 << STATUS3_W56_SHIFT)
#define STATUS3_W56_32BYTE (2 << STATUS3_W56_SHIFT)
#define STATUS3_W56_63BYTE (3 << STATUS3_W56_SHIFT)
/* Bit 7: Reserved */
/* Chip Geometries **********************************************************/
/* All members of the family support uniform 4K-byte sectors */
#define S25FL116K_SECTOR_SIZE (4*1024)
#define S25FL116K_SECTOR_SHIFT (12)
#define S25FL116K_SECTOR_COUNT (512)
#define S25FL116K_PAGE_SIZE (256)
#define S25FL116K_PAGE_SHIFT (8)
#define S25FL132K_SECTOR_SIZE (4*1024)
#define S25FL132K_SECTOR_SHIFT (12)
#define S25FL132K_SECTOR_COUNT (1024)
#define S25FL132K_PAGE_SIZE (256)
#define S25FL132K_PAGE_SHIFT (8)
#define S25FL164K_SECTOR_SIZE (4*1024)
#define S25FL164K_SECTOR_SHIFT (12)
#define S25FL164K_SECTOR_COUNT (2048)
#define S25FL164K_PAGE_SIZE (256)
#define S25FL164K_PAGE_SHIFT (8)
/* Cache flags **************************************************************/
#define S25FL1_CACHE_VALID (1 << 0) /* 1=Cache has valid data */
#define S25FL1_CACHE_DIRTY (1 << 1) /* 1=Cache is dirty */
#define S25FL1_CACHE_ERASED (1 << 2) /* 1=Backing FLASH is erased */
#define IS_VALID(p) ((((p)->flags) & S25FL1_CACHE_VALID) != 0)
#define IS_DIRTY(p) ((((p)->flags) & S25FL1_CACHE_DIRTY) != 0)
#define IS_ERASED(p) ((((p)->flags) & S25FL1_CACHE_ERASED) != 0)
#define SET_VALID(p) do { (p)->flags |= S25FL1_CACHE_VALID; } while (0)
#define SET_DIRTY(p) do { (p)->flags |= S25FL1_CACHE_DIRTY; } while (0)
#define SET_ERASED(p) do { (p)->flags |= S25FL1_CACHE_ERASED; } while (0)
#define CLR_VALID(p) do { (p)->flags &= ~S25FL1_CACHE_VALID; } while (0)
#define CLR_DIRTY(p) do { (p)->flags &= ~S25FL1_CACHE_DIRTY; } while (0)
#define CLR_ERASED(p) do { (p)->flags &= ~S25FL1_CACHE_ERASED; } while (0)
/* 512 byte sector support **************************************************/
#define S25FL1_SECTOR512_SHIFT 9
#define S25FL1_SECTOR512_SIZE (1 << 9)
#define S25FL1_ERASED_STATE 0xff
/****************************************************************************
* Private Types
****************************************************************************/
/* This type represents the state of the MTD device.
* The struct mtd_dev_s must appear at the beginning of the definition so
* that you can freely cast between pointers to struct mtd_dev_s and struct
* s25fl1_dev_s.
*/
struct s25fl1_dev_s
{
struct mtd_dev_s mtd; /* MTD interface */
FAR struct qspi_dev_s *qspi; /* Saved QuadSPI interface instance */
uint16_t nsectors; /* Number of erase sectors */
uint8_t sectorshift; /* Log2 of sector size */
uint8_t pageshift; /* Log2 of page size */
FAR uint8_t *cmdbuf; /* Allocated command buffer */
FAR uint8_t *readbuf; /* Allocated status read buffer */
#ifdef CONFIG_S25FL1_SECTOR512
uint8_t flags; /* Buffered sector flags */
uint16_t esectno; /* Erase sector number in the cache */
FAR uint8_t *sector; /* Allocated sector data */
#endif
};
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
/* Locking */
static void s25fl1_lock(FAR struct qspi_dev_s *qspi);
static inline void s25fl1_unlock(FAR struct qspi_dev_s *qspi);
/* Low-level message helpers */
static int s25fl1_command(FAR struct qspi_dev_s *qspi,
uint8_t cmd);
static int s25fl1_command_address(FAR struct qspi_dev_s *qspi,
uint8_t cmd,
off_t addr,
uint8_t addrlen);
static int s25fl1_command_read(FAR struct qspi_dev_s *qspi,
uint8_t cmd,
FAR void *buffer,
size_t buflen);
static int s25fl1_command_write(FAR struct qspi_dev_s *qspi,
uint8_t cmd,
FAR const void *buffer,
size_t buflen);
static uint8_t sf25fl1_read_status1(FAR struct s25fl1_dev_s *priv);
static uint8_t sf25fl1_read_status2(FAR struct s25fl1_dev_s *priv);
static uint8_t sf25fl1_read_status3(FAR struct s25fl1_dev_s *priv);
static void s25fl1_write_enable(FAR struct s25fl1_dev_s *priv);
static void s25fl1_write_disable(FAR struct s25fl1_dev_s *priv);
static int s25fl1_readid(FAR struct s25fl1_dev_s *priv);
static int s25fl1_protect(FAR struct s25fl1_dev_s *priv,
off_t startblock,
size_t nblocks);
static int s25fl1_unprotect(FAR struct s25fl1_dev_s *priv,
off_t startblock,
size_t nblocks);
static bool s25fl1_isprotected(FAR struct s25fl1_dev_s *priv,
uint8_t status,
off_t address);
static int s25fl1_erase_sector(FAR struct s25fl1_dev_s *priv,
off_t offset);
static int s25fl1_erase_chip(FAR struct s25fl1_dev_s *priv);
static int s25fl1_read_byte(FAR struct s25fl1_dev_s *priv,
FAR uint8_t *buffer,
off_t address, size_t nbytes);
static int s25fl1_write_page(FAR struct s25fl1_dev_s *priv,
FAR const uint8_t *buffer,
off_t address,
size_t nbytes);
#ifdef CONFIG_S25FL1_SECTOR512
static int s25fl1_flush_cache(struct s25fl1_dev_s *priv);
static FAR uint8_t *s25fl1_read_cache(struct s25fl1_dev_s *priv,
off_t sector);
static void s25fl1_erase_cache(struct s25fl1_dev_s *priv,
off_t sector);
static int s25fl1_write_cache(FAR struct s25fl1_dev_s *priv,
FAR const uint8_t *buffer,
off_t sector,
size_t nsectors);
#endif
/* MTD driver methods */
static int s25fl1_erase(FAR struct mtd_dev_s *dev,
off_t startblock,
size_t nblocks);
static ssize_t s25fl1_bread(FAR struct mtd_dev_s *dev,
off_t startblock,
size_t nblocks,
FAR uint8_t *buf);
static ssize_t s25fl1_bwrite(FAR struct mtd_dev_s *dev,
off_t startblock,
size_t nblocks,
FAR const uint8_t *buf);
static ssize_t s25fl1_read(FAR struct mtd_dev_s *dev,
off_t offset,
size_t nbytes,
FAR uint8_t *buffer);
static int s25fl1_ioctl(FAR struct mtd_dev_s *dev,
int cmd,
unsigned long arg);
/****************************************************************************
* Private Data
****************************************************************************/
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: s25fl1_lock
****************************************************************************/
static void s25fl1_lock(FAR struct qspi_dev_s *qspi)
{
/* On QuadSPI buses where there are multiple devices, it will be necessary
* to lock QuadSPI to have exclusive access to the buses for a sequence of
* transfers. The bus should be locked before the chip is selected.
*
* This is a blocking call and will not return until we have exclusive
* access to the QuadSPI bus.
* We will retain that exclusive access until the bus is unlocked.
*/
QSPI_LOCK(qspi, true);
/* After locking the QuadSPI bus, the we also need call the setfrequency,
* setbits, and setmode methods to make sure that the QuadSPI is properly
* configured for the device.
* If the QuadSPI bus is being shared, then it may have been left in an
* incompatible state.
*/
QSPI_SETMODE(qspi, CONFIG_S25FL1_QSPIMODE);
QSPI_SETBITS(qspi, 8);
QSPI_SETFREQUENCY(qspi, CONFIG_S25FL1_QSPI_FREQUENCY);
}
/****************************************************************************
* Name: s25fl1_unlock
****************************************************************************/
static inline void s25fl1_unlock(FAR struct qspi_dev_s *qspi)
{
QSPI_LOCK(qspi, false);
}
/****************************************************************************
* Name: s25fl1_command
****************************************************************************/
static int s25fl1_command(FAR struct qspi_dev_s *qspi, uint8_t cmd)
{
struct qspi_cmdinfo_s cmdinfo;
finfo("CMD: %02x\n", cmd);
cmdinfo.flags = 0;
cmdinfo.addrlen = 0;
cmdinfo.cmd = cmd;
cmdinfo.buflen = 0;
cmdinfo.addr = 0;
cmdinfo.buffer = NULL;
return QSPI_COMMAND(qspi, &cmdinfo);
}
/****************************************************************************
* Name: s25fl1_command_address
****************************************************************************/
static int s25fl1_command_address(FAR struct qspi_dev_s *qspi,
uint8_t cmd,
off_t addr,
uint8_t addrlen)
{
struct qspi_cmdinfo_s cmdinfo;
finfo("CMD: %02x Address: %04lx addrlen=%d\n",
cmd, (unsigned long)addr, addrlen);
cmdinfo.flags = QSPICMD_ADDRESS;
cmdinfo.addrlen = addrlen;
cmdinfo.cmd = cmd;
cmdinfo.buflen = 0;
cmdinfo.addr = addr;
cmdinfo.buffer = NULL;
return QSPI_COMMAND(qspi, &cmdinfo);
}
/****************************************************************************
* Name: s25fl1_command_read
****************************************************************************/
static int s25fl1_command_read(FAR struct qspi_dev_s *qspi, uint8_t cmd,
FAR void *buffer, size_t buflen)
{
struct qspi_cmdinfo_s cmdinfo;
finfo("CMD: %02x buflen: %lu\n", cmd, (unsigned long)buflen);
cmdinfo.flags = QSPICMD_READDATA;
cmdinfo.addrlen = 0;
cmdinfo.cmd = cmd;
cmdinfo.buflen = buflen;
cmdinfo.addr = 0;
cmdinfo.buffer = buffer;
return QSPI_COMMAND(qspi, &cmdinfo);
}
/****************************************************************************
* Name: s25fl1_command_write
****************************************************************************/
static int s25fl1_command_write(FAR struct qspi_dev_s *qspi, uint8_t cmd,
FAR const void *buffer, size_t buflen)
{
struct qspi_cmdinfo_s cmdinfo;
finfo("CMD: %02x buflen: %lu\n", cmd, (unsigned long)buflen);
cmdinfo.flags = QSPICMD_WRITEDATA;
cmdinfo.addrlen = 0;
cmdinfo.cmd = cmd;
cmdinfo.buflen = buflen;
cmdinfo.addr = 0;
cmdinfo.buffer = (FAR void *)buffer;
return QSPI_COMMAND(qspi, &cmdinfo);
}
/****************************************************************************
* Name: sf25fl1_read_status1
****************************************************************************/
static uint8_t sf25fl1_read_status1(FAR struct s25fl1_dev_s *priv)
{
DEBUGVERIFY(s25fl1_command_read(priv->qspi, S25FL1_READ_STATUS1,
(FAR void *)&priv->readbuf[0], 1));
return priv->readbuf[0];
}
/****************************************************************************
* Name: sf25fl1_read_status2
****************************************************************************/
static uint8_t sf25fl1_read_status2(FAR struct s25fl1_dev_s *priv)
{
DEBUGVERIFY(s25fl1_command_read(priv->qspi, S25FL1_READ_STATUS2,
(FAR void *)&priv->readbuf[0], 1));
return priv->readbuf[0];
}
/****************************************************************************
* Name: sf25fl1_read_status3
****************************************************************************/
static uint8_t sf25fl1_read_status3(FAR struct s25fl1_dev_s *priv)
{
DEBUGVERIFY(s25fl1_command_read(priv->qspi, S25FL1_READ_STATUS3,
(FAR void *)&priv->readbuf[0], 1));
return priv->readbuf[0];
}
/****************************************************************************
* Name: s25fl1_write_enable
****************************************************************************/
static void s25fl1_write_enable(FAR struct s25fl1_dev_s *priv)
{
uint8_t status;
do
{
s25fl1_command(priv->qspi, S25FL1_WRITE_ENABLE);
status = sf25fl1_read_status1(priv);
}
while ((status & STATUS1_WEL_MASK) != STATUS1_WEL_ENABLED);
}
/****************************************************************************
* Name: s25fl1_write_disable
****************************************************************************/
static void s25fl1_write_disable(FAR struct s25fl1_dev_s *priv)
{
uint8_t status;
do
{
s25fl1_command(priv->qspi, S25FL1_WRITE_DISABLE);
status = sf25fl1_read_status1(priv);
}
while ((status & STATUS1_WEL_MASK) != STATUS1_WEL_DISABLED);
}
/****************************************************************************
* Name: s25fl1_write_status
****************************************************************************/
static void s25fl1_write_status(FAR struct s25fl1_dev_s *priv)
{
s25fl1_write_enable(priv);
s25fl1_command_write(priv->qspi, S25FL1_WRITE_STATUS,
(FAR const void *)priv->cmdbuf, 3);
s25fl1_write_disable(priv);
}
/****************************************************************************
* Name: s25fl1_readid
****************************************************************************/
static inline int s25fl1_readid(struct s25fl1_dev_s *priv)
{
/* Lock the QuadSPI bus and configure the bus. */
s25fl1_lock(priv->qspi);
/* Read the JEDEC ID */
s25fl1_command_read(priv->qspi, S25FL1_JEDEC_ID, priv->cmdbuf, 3);
/* Unlock the bus */
s25fl1_unlock(priv->qspi);
finfo("Manufacturer: %02x Device Type %02x, Capacity: %02x",
priv->cmdbuf[0], priv->cmdbuf[1], priv->cmdbuf[2]);
/* Check for a recognized memory device type */
if (priv->cmdbuf[1] != S25FL1_JEDEC_DEVICE_TYPE)
{
ferr("ERROR: Unrecognized device type: %02x\n", priv->cmdbuf[1]);
return -ENODEV;
}
/* Check for a supported capacity */
switch (priv->cmdbuf[2])
{
case S25FL116K_JEDEC_CAPACITY:
priv->sectorshift = S25FL116K_SECTOR_SHIFT;
priv->pageshift = S25FL116K_PAGE_SHIFT;
priv->nsectors = S25FL116K_SECTOR_COUNT;
break;
case S25FL132K_JEDEC_CAPACITY:
priv->sectorshift = S25FL132K_SECTOR_SHIFT;
priv->pageshift = S25FL116K_PAGE_SHIFT;
priv->nsectors = S25FL132K_SECTOR_COUNT;
break;
case S25FL164K_JEDEC_CAPACITY:
priv->sectorshift = S25FL164K_SECTOR_SHIFT;
priv->pageshift = S25FL116K_PAGE_SHIFT;
priv->nsectors = S25FL164K_SECTOR_COUNT;
break;
/* Support for this part is not implemented yet */
default:
ferr("ERROR: Unsupported memory capacity: %02x\n", priv->cmdbuf[2]);
return -ENODEV;
}
return OK;
}
/****************************************************************************
* Name: s25fl1_protect
****************************************************************************/
static int s25fl1_protect(FAR struct s25fl1_dev_s *priv,
off_t startblock, size_t nblocks)
{
/* Get the status register value to check the current protection */
priv->cmdbuf[0] = sf25fl1_read_status1(priv);
priv->cmdbuf[1] = sf25fl1_read_status2(priv);
priv->cmdbuf[2] = sf25fl1_read_status3(priv);
if ((priv->cmdbuf[0] & STATUS1_BP_MASK) == STATUS1_BP_NONE)
{
/* Protection already disabled */
return 0;
}
/* Check if sector protection registers are locked */
if ((priv->cmdbuf[0] & STATUS1_SRP0_MASK) == STATUS1_SRP0_LOCKED)
{
/* Yes.. unprotect section protection registers */
priv->cmdbuf[0] &= ~STATUS1_SRP0_MASK;
s25fl1_write_status(priv);
}
/* Set the protection mask to zero.
* REVISIT: This logic should really just set the BP bits as
* necessary to protect the range of sectors.
*/
priv->cmdbuf[0] |= STATUS1_BP_MASK;
s25fl1_write_status(priv);
/* Check the new status */
priv->cmdbuf[0] = sf25fl1_read_status1(priv);
if ((priv->cmdbuf[0] & STATUS1_BP_MASK) != STATUS1_BP_MASK)
{
return -EACCES;
}
return OK;
}
/****************************************************************************
* Name: s25fl1_unprotect
****************************************************************************/
static int s25fl1_unprotect(FAR struct s25fl1_dev_s *priv,
off_t startblock, size_t nblocks)
{
/* Get the status register value to check the current protection */
priv->cmdbuf[0] = sf25fl1_read_status1(priv);
priv->cmdbuf[1] = sf25fl1_read_status2(priv);
priv->cmdbuf[2] = sf25fl1_read_status3(priv);
if ((priv->cmdbuf[0] & STATUS1_BP_MASK) == STATUS1_BP_NONE &&
(priv->cmdbuf[1] & STATUS2_CMP_MASK) == 0)
{
/* Protection already disabled */
return 0;
}
/* Check if sector protection registers are locked */
if ((priv->cmdbuf[0] & STATUS1_SRP0_MASK) == STATUS1_SRP0_LOCKED)
{
/* Yes.. unprotect section protection registers */
priv->cmdbuf[0] &= ~STATUS1_SRP0_MASK;
s25fl1_write_status(priv);
}
/* Set the protection mask to zero (and not complemented).
* REVISIT: This logic should really just re-write the BP bits as
* necessary to unprotect the range of sectors.
*/
priv->cmdbuf[0] &= ~STATUS1_BP_MASK;
priv->cmdbuf[1] &= ~STATUS2_CMP_MASK;
s25fl1_write_status(priv);
/* Check the new status */
priv->cmdbuf[0] = sf25fl1_read_status1(priv);
if ((priv->cmdbuf[0] & (STATUS1_SRP0_MASK | STATUS1_BP_MASK)) != 0)
{
return -EACCES;
}
return OK;
}
/****************************************************************************
* Name: s25fl1_isprotected
****************************************************************************/
static bool s25fl1_isprotected(FAR struct s25fl1_dev_s *priv, uint8_t status,
off_t address)
{
off_t protstart;
off_t protend;
off_t protsize;
unsigned int bp;
/* What is protected? 64 Kb blocks? Or 4Kb sectors? */
if ((status & STATUS1_SEC_MASK) == STATUS1_SEC_BLOCK)
{
/* 64 Kb block */
protsize = 0x00010000;
}
else
{
/* 4 Kb sector */
protsize = 0x00001000;
}
/* The BP field is the essentially a multiplier on this protection size */
bp = (status & STATUS1_BP_MASK) >> STATUS1_BP_SHIFT;
switch (bp)
{
case 0:
return false;
case 1:
break;
case 6:
case 7:
return true;
default:
protsize <<= (protsize << (bp - 1));
break;
}
/* The final protection range then depends on if the protection region is
* configured top-down or bottom up (assuming CMP=0).
*/
if ((status & STATUS1_TB_MASK) != 0)
{
protstart = 0x00000000;
protend = protstart + protsize;
}
else
{
protend = 0x00200000;
protstart = protend - protsize;
}
return (address >= protstart && address < protend);
}
/****************************************************************************
* Name: s25fl1_erase_sector
****************************************************************************/
static int s25fl1_erase_sector(struct s25fl1_dev_s *priv, off_t sector)
{
off_t address;
uint8_t status;
finfo("sector: %08lx\n", (unsigned long)sector);
/* Check that the flash is ready and unprotected */
status = sf25fl1_read_status1(priv);
if ((status & STATUS1_BUSY_MASK) != STATUS1_READY)
{
ferr("ERROR: Flash busy: %02x", status);
return -EBUSY;
}
/* Get the address associated with the sector */
address = (off_t)sector << priv->sectorshift;
if ((status & STATUS1_BP_MASK) != 0 &&
s25fl1_isprotected(priv, status, address))
{
ferr("ERROR: Flash protected: %02x", status);
return -EACCES;
}
/* Send the sector erase command */
s25fl1_write_enable(priv);
s25fl1_command_address(priv->qspi, S25FL1_SECTOR_ERASE, address, 3);
/* Wait for erasure to finish */
while ((sf25fl1_read_status1(priv) & STATUS1_BUSY_MASK) != 0);
return OK;
}
/****************************************************************************
* Name: s25fl1_erase_chip
****************************************************************************/
static int s25fl1_erase_chip(struct s25fl1_dev_s *priv)
{
uint8_t status;
/* Check if the FLASH is protected */
status = sf25fl1_read_status1(priv);
if ((status & STATUS1_BP_MASK) != 0)
{
ferr("ERROR: FLASH is Protected: %02x", status);
return -EACCES;
}
/* Erase the whole chip */
s25fl1_write_enable(priv);
s25fl1_command(priv->qspi, S25FL1_CHIP_ERASE_2);
/* Wait for the erasure to complete */
status = sf25fl1_read_status1(priv);
while ((status & STATUS1_BUSY_MASK) != 0)
{
nxsig_usleep(200 * 1000);
status = sf25fl1_read_status1(priv);
}
return OK;
}
/****************************************************************************
* Name: s25fl1_read_byte
****************************************************************************/
static int s25fl1_read_byte(FAR struct s25fl1_dev_s *priv,
FAR uint8_t *buffer,
off_t address,
size_t buflen)
{
struct qspi_meminfo_s meminfo;
finfo("address: %08lx nbytes: %d\n", (long)address, (int)buflen);
#ifdef CONFIG_S25FL1_SCRAMBLE
meminfo.flags = QSPIMEM_READ | QSPIMEM_QUADIO | QSPIMEM_SCRAMBLE;
#else
meminfo.flags = QSPIMEM_READ | QSPIMEM_QUADIO;
#endif
meminfo.addrlen = 3;
meminfo.dummies = 6;
meminfo.buflen = buflen;
meminfo.cmd = S25FL1_FAST_READ_QUADIO;
meminfo.addr = address;
#ifdef CONFIG_S25FL1_SCRAMBLE
meminfo.key = CONFIG_S25FL1_SCRAMBLE_KEY;
#endif
meminfo.buffer = buffer;
return QSPI_MEMORY(priv->qspi, &meminfo);
}
/****************************************************************************
* Name: s25fl1_write_page
****************************************************************************/
static int s25fl1_write_page(struct s25fl1_dev_s *priv,
FAR const uint8_t *buffer,
off_t address,
size_t buflen)
{
struct qspi_meminfo_s meminfo;
unsigned int pagesize;
unsigned int npages;
int ret;
int i;
finfo("address: %08lx buflen: %u\n",
(unsigned long)address, (unsigned)buflen);
npages = (buflen >> priv->pageshift);
pagesize = (1 << priv->pageshift);
/* Set up non-varying parts of transfer description */
#ifdef CONFIG_S25FL1_SCRAMBLE
meminfo.flags = QSPIMEM_WRITE | QSPIMEM_SCRAMBLE;
#else
meminfo.flags = QSPIMEM_WRITE;
#endif
meminfo.cmd = S25FL1_PAGE_PROGRAM;
meminfo.addrlen = 3;
meminfo.buflen = pagesize;
#ifdef CONFIG_S25FL1_SCRAMBLE
meminfo.key = CONFIG_S25FL1_SCRAMBLE_KEY;
#endif
meminfo.dummies = 0;
/* Then write each page */
for (i = 0; i < npages; i++)
{
/* Set up varying parts of the transfer description */
meminfo.addr = address;
meminfo.buffer = (void *)buffer;
/* Write one page */
s25fl1_write_enable(priv);
ret = QSPI_MEMORY(priv->qspi, &meminfo);
s25fl1_write_disable(priv);
if (ret < 0)
{
ferr("ERROR: QSPI_MEMORY failed writing address=%06x\n",
address);
return ret;
}
/* Update for the next time through the loop */
buffer += pagesize;
address += pagesize;
buflen -= pagesize;
}
/* The transfer should always be an even number of sectors and hence also
* pages. There should be no remainder.
*/
DEBUGASSERT(buflen == 0);
return OK;
}
/****************************************************************************
* Name: s25fl1_flush_cache
****************************************************************************/
#ifdef CONFIG_S25FL1_SECTOR512
static int s25fl1_flush_cache(struct s25fl1_dev_s *priv)
{
int ret = OK;
/* If the cached is dirty (meaning that it no longer matches the old FLASH
* contents) or was erased (with the cache containing the correct FLASH
* contents), then write the cached erase block to FLASH.
*/
if (IS_DIRTY(priv) || IS_ERASED(priv))
{
off_t address;
/* Convert the erase sector numuber into a FLASH address */
address = (off_t)priv->esectno << priv->sectorshift;
/* Write entire erase block to FLASH */
ret = s25fl1_write_page(priv,
priv->sector,
address,
1 << priv->sectorshift);
if (ret < 0)
{
ferr("ERROR: s25fl1_write_page failed: %d\n", ret);
}
/* The case is no long dirty and the FLASH is no longer erased */
CLR_DIRTY(priv);
CLR_ERASED(priv);
}
return ret;
}
#endif
/****************************************************************************
* Name: s25fl1_read_cache
****************************************************************************/
#ifdef CONFIG_S25FL1_SECTOR512
static FAR uint8_t *s25fl1_read_cache(struct s25fl1_dev_s *priv,
off_t sector)
{
off_t esectno;
int shift;
int index;
int ret;
/* Convert from the 512 byte sector to the erase sector size of the device.
* For exmample, if the actual erase sector size if 4Kb (1 << 12), then we
* first shift to the right by 3 to get the sector number in 4096
* increments.
*/
shift = priv->sectorshift - S25FL1_SECTOR512_SHIFT;
esectno = sector >> shift;
finfo("sector: %ld esectno: %d shift=%d\n", sector, esectno, shift);
/* Check if the requested erase block is already in the cache */
if (!IS_VALID(priv) || esectno != priv->esectno)
{
/* No.. Flush any dirty erase block currently in the cache */
ret = s25fl1_flush_cache(priv);
if (ret < 0)
{
ferr("ERROR: s25fl1_flush_cache failed: %d\n", ret);
return NULL;
}
/* Read the erase block into the cache */
ret = s25fl1_read_byte(priv, priv->sector,
(esectno << priv->sectorshift),
(1 << priv->sectorshift));
if (ret < 0)
{
ferr("ERROR: s25fl1_read_byte failed: %d\n", ret);
return NULL;
}
/* Mark the sector as cached */
priv->esectno = esectno;
SET_VALID(priv); /* The data in the cache is valid */
CLR_DIRTY(priv); /* It should match the FLASH contents */
CLR_ERASED(priv); /* The underlying FLASH has not been erased */
}
/* Get the index to the 512 sector in the erase block that holds the
* argument
*/
index = sector & ((1 << shift) - 1);
/* Return the address in the cache that holds this sector */
return &priv->sector[index << S25FL1_SECTOR512_SHIFT];
}
#endif
/****************************************************************************
* Name: s25fl1_erase_cache
****************************************************************************/
#ifdef CONFIG_S25FL1_SECTOR512
static void s25fl1_erase_cache(struct s25fl1_dev_s *priv, off_t sector)
{
FAR uint8_t *dest;
/* First, make sure that the erase block containing the 512 byte sector is
* in the cache.
*/
dest = s25fl1_read_cache(priv, sector);
/* Erase the block containing this sector if it is not already erased.
* The erased indicated will be cleared when the data from the erase
* sector is read into the cache and set here when we erase the block.
*/
if (!IS_ERASED(priv))
{
off_t esectno = sector >>
(priv->sectorshift - S25FL1_SECTOR512_SHIFT);
finfo("sector: %ld esectno: %d\n", sector, esectno);
DEBUGVERIFY(s25fl1_erase_sector(priv, esectno));
SET_ERASED(priv);
}
/* Put the cached sector data into the erase state and mart the cache as
* dirty (but don't update the FLASH yet. The caller will do that at a
* more optimal time).
*/
memset(dest, S25FL1_ERASED_STATE, S25FL1_SECTOR512_SIZE);
SET_DIRTY(priv);
}
#endif
/****************************************************************************
* Name: s25fl1_write_cache
****************************************************************************/
#ifdef CONFIG_S25FL1_SECTOR512
static int s25fl1_write_cache(FAR struct s25fl1_dev_s *priv,
FAR const uint8_t *buffer, off_t sector,
size_t nsectors)
{
FAR uint8_t *dest;
int ret;
for (; nsectors > 0; nsectors--)
{
/* First, make sure that the erase block containing 512 byte sector is
* in memory.
*/
dest = s25fl1_read_cache(priv, sector);
/* Erase the block containing this sector if it is not already erased.
* The erased indicated will be cleared when the data from the erase
* sector is read into the cache and set here when we erase the sector.
*/
if (!IS_ERASED(priv))
{
off_t esectno = sector >>
(priv->sectorshift - S25FL1_SECTOR512_SHIFT);
finfo("sector: %ld esectno: %d\n", sector, esectno);
ret = s25fl1_erase_sector(priv, esectno);
if (ret < 0)
{
ferr("ERROR: s25fl1_erase_sector failed: %d\n", ret);
return ret;
}
SET_ERASED(priv);
}
/* Copy the new sector data into cached erase block */
memcpy(dest, buffer, S25FL1_SECTOR512_SIZE);
SET_DIRTY(priv);
/* Set up for the next 512 byte sector */
buffer += S25FL1_SECTOR512_SIZE;
sector++;
}
/* Flush the last erase block left in the cache */
return s25fl1_flush_cache(priv);
}
#endif
/****************************************************************************
* Name: s25fl1_erase
****************************************************************************/
static int s25fl1_erase(FAR struct mtd_dev_s *dev,
off_t startblock,
size_t nblocks)
{
FAR struct s25fl1_dev_s *priv = (FAR struct s25fl1_dev_s *)dev;
size_t blocksleft = nblocks;
#ifdef CONFIG_S25FL1_SECTOR512
int ret;
#endif
finfo("startblock: %08lx nblocks: %d\n", (long)startblock, (int)nblocks);
/* Lock access to the SPI bus until we complete the erase */
s25fl1_lock(priv->qspi);
while (blocksleft-- > 0)
{
/* Erase each sector */
#ifdef CONFIG_S25FL1_SECTOR512
s25fl1_erase_cache(priv, startblock);
#else
s25fl1_erase_sector(priv, startblock);
#endif
startblock++;
}
#ifdef CONFIG_S25FL1_SECTOR512
/* Flush the last erase block left in the cache */
ret = s25fl1_flush_cache(priv);
if (ret < 0)
{
nblocks = ret;
}
#endif
s25fl1_unlock(priv->qspi);
return (int)nblocks;
}
/****************************************************************************
* Name: s25fl1_bread
****************************************************************************/
static ssize_t s25fl1_bread(FAR struct mtd_dev_s *dev, off_t startblock,
size_t nblocks, FAR uint8_t *buffer)
{
#ifndef CONFIG_S25FL1_SECTOR512
FAR struct s25fl1_dev_s *priv = (FAR struct s25fl1_dev_s *)dev;
#endif
ssize_t nbytes;
finfo("startblock: %08lx nblocks: %d\n", (long)startblock, (int)nblocks);
/* On this device, we can handle the block read just like the byte-oriented
* read
*/
#ifdef CONFIG_S25FL1_SECTOR512
nbytes = s25fl1_read(dev, startblock << S25FL1_SECTOR512_SHIFT,
nblocks << S25FL1_SECTOR512_SHIFT, buffer);
if (nbytes > 0)
{
nbytes >>= S25FL1_SECTOR512_SHIFT;
}
#else
nbytes = s25fl1_read(dev, startblock << priv->pageshift,
nblocks << priv->pageshift, buffer);
if (nbytes > 0)
{
nbytes >>= priv->pageshift;
}
#endif
return nbytes;
}
/****************************************************************************
* Name: s25fl1_bwrite
****************************************************************************/
static ssize_t s25fl1_bwrite(FAR struct mtd_dev_s *dev, off_t startblock,
size_t nblocks, FAR const uint8_t *buffer)
{
FAR struct s25fl1_dev_s *priv = (FAR struct s25fl1_dev_s *)dev;
int ret = (int)nblocks;
finfo("startblock: %08lx nblocks: %d\n", (long)startblock, (int)nblocks);
/* Lock the QuadSPI bus and write all of the pages to FLASH */
s25fl1_lock(priv->qspi);
#if defined(CONFIG_S25FL1_SECTOR512)
ret = s25fl1_write_cache(priv, buffer, startblock, nblocks);
if (ret < 0)
{
ferr("ERROR: s25fl1_write_cache failed: %d\n", ret);
}
#else
ret = s25fl1_write_page(priv, buffer, startblock << priv->pageshift,
nblocks << priv->pageshift);
if (ret < 0)
{
ferr("ERROR: s25fl1_write_page failed: %d\n", ret);
}
#endif
s25fl1_unlock(priv->qspi);
return ret < 0 ? ret : nblocks;
}
/****************************************************************************
* Name: s25fl1_read
****************************************************************************/
static ssize_t s25fl1_read(FAR struct mtd_dev_s *dev,
off_t offset,
size_t nbytes,
FAR uint8_t *buffer)
{
FAR struct s25fl1_dev_s *priv = (FAR struct s25fl1_dev_s *)dev;
int ret;
finfo("offset: %08lx nbytes: %d\n", (long)offset, (int)nbytes);
/* Lock the QuadSPI bus and select this FLASH part */
s25fl1_lock(priv->qspi);
ret = s25fl1_read_byte(priv, buffer, offset, nbytes);
s25fl1_unlock(priv->qspi);
if (ret < 0)
{
ferr("ERROR: s25fl1_read_byte returned: %d\n", ret);
return (ssize_t)ret;
}
finfo("return nbytes: %d\n", (int)nbytes);
return (ssize_t)nbytes;
}
/****************************************************************************
* Name: s25fl1_ioctl
****************************************************************************/
static int s25fl1_ioctl(FAR struct mtd_dev_s *dev,
int cmd,
unsigned long arg)
{
FAR struct s25fl1_dev_s *priv = (FAR struct s25fl1_dev_s *)dev;
int ret = -EINVAL; /* Assume good command with bad parameters */
finfo("cmd: %d\n", cmd);
switch (cmd)
{
case MTDIOC_GEOMETRY:
{
FAR struct mtd_geometry_s *geo =
(FAR struct mtd_geometry_s *)((uintptr_t)arg);
if (geo)
{
memset(geo, 0, sizeof(*geo));
/* Populate the geometry structure with information need to
* know the capacity and how to access the device.
*
* NOTE:
* that the device is treated as though it where just an array
* of fixed size blocks. That is most likely not true, but
* the client will expect the device logic to do whatever is
* necessary to make it appear so.
*/
#ifdef CONFIG_S25FL1_SECTOR512
geo->blocksize = (1 << S25FL1_SECTOR512_SHIFT);
geo->erasesize = (1 << S25FL1_SECTOR512_SHIFT);
geo->neraseblocks = priv->nsectors <<
(priv->sectorshift - S25FL1_SECTOR512_SHIFT);
#else
geo->blocksize = (1 << priv->pageshift);
geo->erasesize = (1 << priv->sectorshift);
geo->neraseblocks = priv->nsectors;
#endif
ret = OK;
finfo("blocksize: %d erasesize: %d neraseblocks: %d\n",
geo->blocksize, geo->erasesize, geo->neraseblocks);
}
}
break;
case BIOC_PARTINFO:
{
FAR struct partition_info_s *info =
(FAR struct partition_info_s *)arg;
if (info != NULL)
{
#ifdef CONFIG_S25FL1_SECTOR512
info->numsectors = priv->nsectors <<
(priv->sectorshift - S25FL1_SECTOR512_SHIFT);
info->sectorsize = 1 << S25FL1_SECTOR512_SHIFT;
#else
info->numsectors = priv->nsectors <<
(priv->sectorshift - priv->pageshift);
info->sectorsize = 1 << priv->pageshift;
#endif
info->startsector = 0;
info->parent[0] = '\0';
ret = OK;
}
}
break;
case MTDIOC_BULKERASE:
{
/* Erase the entire device */
s25fl1_lock(priv->qspi);
ret = s25fl1_erase_chip(priv);
s25fl1_unlock(priv->qspi);
}
break;
case MTDIOC_PROTECT:
{
FAR const struct mtd_protect_s *prot =
(FAR const struct mtd_protect_s *)((uintptr_t)arg);
DEBUGASSERT(prot);
ret = s25fl1_protect(priv, prot->startblock, prot->nblocks);
}
break;
case MTDIOC_UNPROTECT:
{
FAR const struct mtd_protect_s *prot =
(FAR const struct mtd_protect_s *)((uintptr_t)arg);
DEBUGASSERT(prot);
ret = s25fl1_unprotect(priv, prot->startblock, prot->nblocks);
}
break;
case MTDIOC_ERASESTATE:
{
FAR uint8_t *result = (FAR uint8_t *)arg;
*result = S25FL1_ERASED_STATE;
ret = OK;
}
break;
default:
ret = -ENOTTY; /* Bad/unsupported command */
break;
}
finfo("return %d\n", ret);
return ret;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: s25fl1_initialize
*
* Description:
* Create an initialize MTD device instance for the QuadSPI-based ST24FL1
* FLASH part.
*
* MTD devices are not registered in the file system, but are created as
* instances that can be bound to other functions (such as a block or
* character driver front end).
*
****************************************************************************/
FAR struct mtd_dev_s *s25fl1_initialize(FAR struct qspi_dev_s *qspi,
bool unprotect)
{
FAR struct s25fl1_dev_s *priv;
int ret;
finfo("qspi: %p\n", qspi);
DEBUGASSERT(qspi != NULL);
/* Allocate a state structure (we allocate the structure instead of using
* a fixed, static allocation so that we can handle multiple FLASH devices.
* The current implementation would handle only one FLASH part per QuadSPI
* device (only because of the QSPIDEV_FLASH(0) definition) and so would
* have to be extended to handle multiple FLASH parts on the same QuadSPI
* bus.
*/
priv = (FAR struct s25fl1_dev_s *)kmm_zalloc(sizeof(struct s25fl1_dev_s));
if (priv)
{
/* Initialize the allocated structure (unsupported methods were
* nullified by kmm_zalloc).
*/
priv->mtd.erase = s25fl1_erase;
priv->mtd.bread = s25fl1_bread;
priv->mtd.bwrite = s25fl1_bwrite;
priv->mtd.read = s25fl1_read;
priv->mtd.ioctl = s25fl1_ioctl;
priv->mtd.name = "s25fl1";
priv->qspi = qspi;
/* Allocate a 4-byte buffer to support DMA command data */
priv->cmdbuf = (FAR uint8_t *)QSPI_ALLOC(qspi, 4);
if (priv->cmdbuf == NULL)
{
ferr("ERROR Failed to allocate command buffer\n");
goto errout_with_priv;
}
/* Allocate a one-byte buffer to support DMA status read data */
priv->readbuf = (FAR uint8_t *)QSPI_ALLOC(qspi, 1);
if (priv->readbuf == NULL)
{
ferr("ERROR Failed to allocate read buffer\n");
goto errout_with_cmdbuf;
}
/* Identify the FLASH chip and get its capacity */
ret = s25fl1_readid(priv);
if (ret != OK)
{
/* Unrecognized! Discard all of that work we just did and return
* NULL
*/
ferr("ERROR Unrecognized QSPI device\n");
goto errout_with_readbuf;
}
/* Enable quad mode */
priv->cmdbuf[0] = sf25fl1_read_status1(priv);
priv->cmdbuf[1] = sf25fl1_read_status2(priv);
priv->cmdbuf[2] = sf25fl1_read_status3(priv);
while ((priv->cmdbuf[1] & STATUS2_QUAD_ENABLE_MASK) == 0)
{
priv->cmdbuf[1] |= STATUS2_QUAD_ENABLE;
s25fl1_write_status(priv);
priv->cmdbuf[1] = sf25fl1_read_status2(priv);
nxsig_usleep(50 * 1000);
}
/* Unprotect FLASH sectors if so requested. */
if (unprotect)
{
ret = s25fl1_unprotect(priv, 0, priv->nsectors - 1);
if (ret < 0)
{
ferr("ERROR: Sector unprotect failed\n");
}
}
#ifdef CONFIG_S25FL1_SECTOR512 /* Simulate a 512 byte sector */
/* Allocate a buffer for the erase block cache */
priv->sector = (FAR uint8_t *)QSPI_ALLOC(qspi, 1 << priv->sectorshift);
if (priv->sector == NULL)
{
/* Allocation failed!
* Discard all of that work we just did and return NULL
*/
ferr("ERROR: Sector allocation failed\n");
goto errout_with_readbuf;
}
#endif
}
/* Return the implementation-specific state structure as the MTD device */
finfo("Return %p\n", priv);
return (FAR struct mtd_dev_s *)priv;
errout_with_readbuf:
QSPI_FREE(qspi, priv->readbuf);
errout_with_cmdbuf:
QSPI_FREE(qspi, priv->cmdbuf);
errout_with_priv:
kmm_free(priv);
return NULL;
}
Reference in New Issue View Git Blame Copy Permalink