nuttx

clock

sched/clock/ timekeeping: Use clock_basetime() to initialize g_clock_wall_time to get the best initial RTC value and initialize g_clock_last_counter too since the hardware may not start counting from zero.

2018-11-12 07:00:41 -06:00

environ

Documentation/NuttShell.html: Add a little more information for the NSH set command.

2018-10-02 11:57:39 -06:00

errno

Standardization of some function headers.

2018-03-13 09:52:27 -06:00

group

sched/group/group_foreachchild.c: group_foreachchild iterate by reverse order since the callback(e.g. group_killchildren) may remove the tcb from list

2018-11-08 07:03:30 -06:00

init

Assertions: Identify the running task correctly when dumping task state information. It takes time to switch to the target task after g_readytorun has been modified. If panic/assert happen during this period, the dump will contain the incorrect and confusing information due to the difference between the real running task and the return value of this_task(). This change resolve this problem by adding g_running_task to track the real running task through the context switch.

2018-11-15 07:11:51 -06:00

irq

Rethink some of the conditional logic of commit 1ac95584603258402ea4e9c48977e52f494f4c77: If the Critical Section Monitor enabled, that that platform-specific timer should be used to measure interrupt processing time, no matter what.

2018-11-26 12:18:58 -06:00

module

Fix some typographical errors.

2018-09-14 06:55:45 -06:00

mqueue

fs/aio, libs/libc/aio, sched/mqueue, sched/timer, and sched/signal: Remove the code duplication for SIGEV_THREAD.

2018-11-08 08:19:17 -06:00

paging

Replace all ASSERT with DEBUGASSERT to save the code space

2018-08-24 06:58:30 -06:00

pthread

Fix some typographical errors.

2018-09-14 06:55:45 -06:00

sched

sched/irq and sched/sched: Measurement of interrupt handler duration used to be available only in Tickless mode since it used the high resolution Tickless timer to measure interrupt time. This commit adds CONFIG_SCHED_IRQMONITOR_GETTIME which, if enabled, will force the interrupt duration caculation to use the same high-resolution, platform-specific timer as is used with the Critical Section Monitor. This leads to two improvements: (1) You can now measure interrupt duration in non-Tickless mode, and (2) in either mode, the interrupt duration and the critical section measures will use the same high-resulotion timer and should, therefore, never be any descripancy due to different clock sources.

2018-11-26 11:29:20 -06:00

semaphore

mm/iob and sched/semaphore: Work around some issues with the IOB throttle semaphore. It has some odd behaviors that can cause assertions in sem_post(). Also, it seems to get outside of its range occasionally. Need to REVISIT this.

2018-09-10 11:32:09 -06:00

signal

Critical Section Monitor: Add low level timer support for simulation. Fix serial bugs and logic errors in initial implementation. Still does not work; takes assertions.

2018-11-24 15:07:12 -06:00

task

binfmt/ and libs/libc: Make exepath_*() more common:

2018-11-08 07:27:14 -06:00

timer

fs/aio, libs/libc/aio, sched/mqueue, sched/timer, and sched/signal: Remove the code duplication for SIGEV_THREAD.

2018-11-08 08:19:17 -06:00

wdog

sched/wdog: improve accuracy of wd_gettime() in tickless mode

2018-11-09 09:26:34 -06:00

wqueue

Squashed commit of the following:

2018-09-12 08:57:06 -06:00

.gitignore

…

Kconfig

Rethink some of the conditional logic of commit 1ac95584603258402ea4e9c48977e52f494f4c77: If the Critical Section Monitor enabled, that that platform-specific timer should be used to measure interrupt processing time, no matter what.

2018-11-26 12:18:58 -06:00

Makefile

TLS: Simplify

2016-03-11 07:17:32 -06:00