sergiotarxz/nuttx
sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
nuttx/boards/arm/stm32f7/stm32f746g-disco/src/stm32f746g-disco.h

268 lines
8.0 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/stm32f7/stm32f746g-disco/src/stm32f746g-disco.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_STM32F7_STM32F746G_DISCO_SRC_STM32F746G_DISCO_H
#define __BOARDS_ARM_STM32F7_STM32F746G_DISCO_SRC_STM32F746G_DISCO_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
#define HAVE_USBDEV 1
#define HAVE_USBHOST 1
#define HAVE_USBMONITOR 1
/* Can't support USB host or device features if USB OTG FS is not enabled */
#ifndef CONFIG_STM32F7_OTGFS
# undef HAVE_USBDEV
# undef HAVE_USBHOST
#endif
/* Can't support USB device if USB device is not enabled */
#ifndef CONFIG_USBDEV
# undef HAVE_USBDEV
#endif
/* Can't support USB host is USB host is not enabled */
#ifndef CONFIG_USBHOST
# undef HAVE_USBHOST
#endif
/* Check if we should enable the USB monitor before starting NSH */
#ifndef CONFIG_USBMONITOR
# undef HAVE_USBMONITOR
#endif
#ifndef HAVE_USBDEV
# undef CONFIG_USBDEV_TRACE
#endif
#if !defined(CONFIG_USBDEV_TRACE) && !defined(CONFIG_USBHOST_TRACE)
# undef HAVE_USBMONITOR
#endif
/* procfs File System */
#ifdef CONFIG_FS_PROCFS
# ifdef CONFIG_NSH_PROC_MOUNTPOINT
# define STM32_PROCFS_MOUNTPOINT CONFIG_NSH_PROC_MOUNTPOINT
# else
# define STM32_PROCFS_MOUNTPOINT "/proc"
# endif
#endif
#ifdef CONFIG_STM32F7_SDMMC
#define HAVE_SDIO
#else
#undef HAVE_SDIO
#endif
/* STM32F736G Discovery GPIOs */
/* The STM32F746G-DISCO board has numerous LEDs but only one,
* LD1 located near the reset button, that can be controlled by software
* (LD2 is a power indicator, LD3-6 indicate USB status, LD7 is
* controlled by the ST-Link).
*
* LD1 is controlled by PI1 which is also the SPI2_SCK at the Arduino
* interface.
* One end of LD1 is grounded so a high output on PI1 will illuminate the
* LED.
*/
#define GPIO_LD1 (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTI | GPIO_PIN1)
/* Pushbutton B1, labelled "User", is connected to GPIO PI11.
* A high value will be sensed when the button is depressed.
* Note that the EXTI interrupt is configured.
*/
#define MIN_IRQBUTTON BUTTON_USER
#define MAX_IRQBUTTON BUTTON_USER
#define NUM_IRQBUTTONS 1
#define GPIO_BTN_USER (GPIO_INPUT | GPIO_FLOAT | GPIO_EXTI | GPIO_PORTI | GPIO_PIN11)
/* Sporadic scheduler instrumentation.
* This configuration has been used for evaluating the NuttX sporadic
* scheduler.
* In this evaluation, two GPIO outputs are used.
* One indicating the priority (high or low) of the sporadic thread and one
* indicating where the thread is running or not.
*
* There is nothing special about the pin selections:
*
* Arduino D2 PG6 - Indicates priority
* Arduino D4 PG7 - Indicates that the thread is running
*/
#define GPIO_SCHED_HIGHPRI (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTG | GPIO_PIN6)
#define GPIO_SCHED_RUNNING (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_50MHz | GPIO_OUTPUT_CLEAR | \
GPIO_PORTG | GPIO_PIN7)
#define GPIO_LCD_DISP (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTI|GPIO_PIN12)
#define GPIO_LCD_BL (GPIO_OUTPUT|GPIO_PUSHPULL|GPIO_SPEED_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTK|GPIO_PIN3)
/* SD/TF Card'detected pin */
#define GPIO_SDIO_NCD (GPIO_INPUT|GPIO_FLOAT|GPIO_EXTI|GPIO_PORTC|GPIO_PIN13)
#define SDIO_SLOTNO 0
#define SDIO_MINOR 0
/****************************************************************************
* Public Data
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Name: stm32_bringup
*
* Description:
* Perform architecture-specific initialization
*
* CONFIG_BOARD_LATE_INITIALIZE=y :
* Called from board_late_initialize().
*
* CONFIG_BOARD_LATE_INITIALIZE=n && CONFIG_BOARDCTL=y :
* Called from the NSH library
*
****************************************************************************/
int stm32_bringup(void);
/****************************************************************************
* Name: stm32_adc_setup
*
* Description:
* Initialize ADC and register the ADC driver.
*
****************************************************************************/
#ifdef CONFIG_ADC
int stm32_adc_setup(void);
#endif
/****************************************************************************
* Name: stm32_spidev_initialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the
* stm32f746g-disco board.
*
****************************************************************************/
void weak_function stm32_spidev_initialize(void);
/****************************************************************************
* Name: arch_sporadic_initialize
*
* Description:
* This configuration has been used for evaluating the NuttX sporadic
* scheduler.
*
****************************************************************************/
#ifdef CONFIG_SPORADIC_INSTRUMENTATION
void arch_sporadic_initialize(void);
#endif
/****************************************************************************
* Name: stm32_enablefmc
*
* Description:
* enable clocking to the FMC module
*
****************************************************************************/
#ifdef CONFIG_STM32F7_FMC
void stm32_enablefmc(void);
#endif
/****************************************************************************
* Name: stm32_disablefmc
*
* Description:
* disable clocking to the FMC module
*
****************************************************************************/
#ifdef CONFIG_STM32F7_FMC
void stm32_disablefmc(void);
#endif
/****************************************************************************
* Name: stm32_tsc_setup
*
* Description:
* This function is called by board-bringup logic to configure the
* touchscreen device. This function will register the driver as
* /dev/inputN where N is the minor device number.
*
* Input Parameters:
* minor - The input device minor number
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
#ifdef CONFIG_INPUT_FT5X06
int stm32_tsc_setup(int minor);
#endif
#ifdef CONFIG_MTD_N25QXXX
int stm32_n25qxxx_setup(void);
#endif
#ifdef HAVE_SDIO
int stm32_sdio_initialize(void);
#endif
#ifdef CONFIG_AUDIO_WM8994
int stm32_wm8994_initialize(int minor);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_ARM_STM32F7_STM32F746G_DISCO_SRC_STM32F746G_DISCO_H */
Reference in New Issue View Git Blame Copy Permalink