configs/skp16c26/README.txt
^^^^^^^^^^^^^^^^^^^^^^^^^^^
1. The buildroot package can be used to build an M16C toolchain. The toolchain
buildroot can be downloaded from misc/buildroot in the NuttX SVN. Insructions
for building the toolchain are provided below.
However, the target cannot be built because the GNU m16c-elf-ld link fails with
the following message:
m32c-elf-ld: BFD (GNU Binutils) 2.19 assertion fail /home/Owner/projects/nuttx/buildroot/toolchain_build_m32c/binutils-2.19/bfd/elf32-m32c.c:482
Where the reference line is:
/* If the symbol is out of range for a 16-bit address,
we must have allocated a plt entry. */
BFD_ASSERT (*plt_offset != (bfd_vma) -1);
No workaround is known at this time. This is a show stopper for M16C.
2. A supported version of the M16C toolchain is available here:
http://www.kpitgnutools.com/index.php
This download is free but requires registration. Unfortunately, this v0901 of
this toolchain shows the same behavior:
c:\Hew3\Tools\KPIT Cummins\GNUM16CM32C-ELF\v0901\m32c-elf\bin\m32c-elf-ld.exe: BFD (GNU Binutils) 2.19-GNUM16CM32C_v0901 assertion fail /home/kpit/fsfsrc/binutils-2.19/bfd/elf32-m32c.c:482
It is possible that this error messasge my be telling me -- a very roundabout way --
that I have exceeded the FLASH region, but I think that unlikely (it is difficult
to know if the link does not complete gracefully).
BUILDING THE R8C/M16C/M32C GNU TOOLCHAIN USING BUILDROOT
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
NOTE: See the toolchain issues above -- you may not want to waste your time.
1. CD to the correct directory.
Change to the directory just above the NuttX installation. If <nuttx-dir> is
where NuttX is installed, then cd to <nuttx-dir>/..
2. Get and Install the buildroot Module
a. Using a release tarball:
cd <nuttx-dir>/..
Download the appropriate buildroot package.
unpack the buildroot package
rename the directory to buildroot
b. Using SVN
Check out the misc/buildroot module. SVN checkout instructions:
svn co https://nuttx.svn.sourceforge.net/svnroot/nuttx nuttx/trunk/misc/buildroot
Move the buildroot Source Tree and create the archive directory
mv misc/buildroot .
Make the archive directory:
mkdir archive
The <nuttx-dir>/../buildroot is where the toolchain is built;
The <nuttx-dir>/../archive directory is where toolchain sources will be downloaded.
3. Make sure that NuttX is configured
cd <nuttx-dir>/tools
./configure.sh <nuttx-configuration>
4. Configure and Make the buildroot
cd buildroot
cp configs/m32c-defconfig-4.2.4 .config
make oldconfig
make
This will download the large source packages for the toolchain and build the toolchain.
The resulting binaries will be under buildroot/build_m32c. There will also be a
large build directory called toolchain_build_m32c; this directory can be removed once
the build completes successfully.
Cygwin GCC BUILD NOTES
^^^^^^^^^^^^^^^^^^^^^^
On Cygwin, the buildroot 'make' command will fail with an error like:
"...
build/genchecksum cc1-dummy > cc1-checksum.c
opening cc1-dummy: No such file or directory
..."
This is caused because on Cygwin, host executables will be generated with the extension .exe
and, apparently, the make variable "exeext" is set incorrectly. A work around after the
above occurs is:
cd toolchain_build_m32c/gcc-4.2.4-initial/gcc # Go to the directory where error occurred
mv cc1-dummy.exe cc1-dummy # Rename the executable without .exe
rm cc1-checksum.c # Get rid of the bad generated file
Then resume the buildroot make:
cd - # Back to the buildroot make directory
make # Restart the build
GCC is built twice. First a initial, "bootstap" GCC is produced in
toolchain_build_m32c/gcc-4.2.4-initial, then the final GCC is produced in
toolchain_build_m32c/gcc-4.2.4-final. The above error will occur twice: Once for
the intial GCC build (see above) and once for the final GCC build. For the final GCC
build, the workaround is the same except that the directory will be
toolchain_build_m32c/gcc-4.2.4-final/gcc.
ea1594a398