sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
0f10f6bdec
nuttx/configs/stm32ldiscovery/include/board.h

312 lines
12 KiB
C
Raw Blame History

/************************************************************************************
* configs/stm32ldiscovery/include/board.h
* include/arch/board/board.h
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIG_STM32LDISCOVERY_INCLUDE_BOARD_H
#define __CONFIG_STM32LDISCOVERY_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#ifndef __ASSEMBLY__
# include <stdint.h>
#endif
#include "stm32_rcc.h"
#include "stm32.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* Four different clock sources can be used to drive the system clock (SYSCLK):
*
* - HSI high-speed internal oscillator clock
* Generated from an internal 16 MHz RC oscillator
* - HSE high-speed external oscillator clock
* Normally driven by an external crystal (X3). However, this crystal is not fitted
* on the STM32L-Discovery board.
* - PLL clock
* - MSI multispeed internal oscillator clock
* The MSI clock signal is generated from an internal RC oscillator. Seven frequency
* ranges are available: 65.536 kHz, 131.072 kHz, 262.144 kHz, 524.288 kHz, 1.048 MHz,
* 2.097 MHz (default value) and 4.194 MHz.
*
* The devices have the following two secondary clock sources
* - LSI low-speed internal RC clock
* Drives the watchdog and RTC. Approximately 37KHz
* - LSE low-speed external oscillator clock
* Driven by 32.768KHz crystal (X2) on the OSC32_IN and OSC32_OUT pins.
*/
#define STM32_BOARD_XTAL 8000000ul /* X3 on board (not fitted)*/
#define STM32_HSI_FREQUENCY 16000000ul /* Approximately 16MHz */
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
#define STM32_MSI_FREQUENCY 2097000 /* Default is approximately 2.097Mhz */
#define STM32_LSI_FREQUENCY 37000 /* Approximately 37KHz */
#define STM32_LSE_FREQUENCY 32768 /* X2 on board */
/* PLL Configuration
*
* - PLL source is HSI -> 16MHz input (nominal)
* - PLL multipler is 6 -> 96MHz PLL VCO clock output (for USB)
* - PLL output divider 3 -> 32MHz divided down PLL VCO clock output
*
* Resulting SYSCLK frequency is 16MHz x 6 / 3 = 32MHz
*
* USB/SDIO:
* If the USB or SDIO interface is used in the application, the PLL VCO
* clock (defined by STM32_CFGR_PLLMUL) must be programmed to output a 96
* MHz frequency. This is required to provide a 48 MHz clock to the USB or
* SDIO (SDIOCLK or USBCLK = PLLVCO/2).
* SYSCLK
* The system clock is derived from the PLL VCO divided by the output division factor.
* Limitations:
* 96 MHz as PLLVCO when the product is in range 1 (1.8V),
* 48 MHz as PLLVCO when the product is in range 2 (1.5V),
* 24 MHz when the product is in range 3 (1.2V).
* Output division to avoid exceeding 32 MHz as SYSCLK.
* The minimum input clock frequency for PLL is 2 MHz (when using HSE as PLL source).
*/
#define STM32_CFGR_PLLSRC 0 /* Source is 16MHz HSI */
#ifdef CONFIG_STM32_USB
# define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx6 /* PLLMUL = 6 */
# define STM32_CFGR_PLLDIV RCC_CFGR_PLLDIV_3 /* PLLDIV = 3 */
# define STM32_PLL_FREQUENCY (6*STM32_HSI_FREQUENCY) /* PLL VCO Frequency is 96MHz */
#else
# define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx4 /* PLLMUL = 4 */
# define STM32_CFGR_PLLDIV RCC_CFGR_PLLDIV_2 /* PLLDIV = 2 */
# define STM32_PLL_FREQUENCY (4*STM32_HSI_FREQUENCY) /* PLL VCO Frequency is 64MHz */
#endif
/* Use the PLL and set the SYSCLK source to be the divided down PLL VCO output
* frequency (STM32_PLL_FREQUENCY divided by the PLLDIV value).
*/
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL /* Use the PLL as the SYSCLK */
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
#ifdef CONFIG_STM32_USB
# define STM32_SYSCLK_FREQUENCY (STM32_PLL_FREQUENCY/3) /* SYSCLK frequence is 96MHz/PLLDIV = 32MHz */
#else
# define STM32_SYSCLK_FREQUENCY (STM32_PLL_FREQUENCY/2) /* SYSCLK frequence is 64MHz/PLLDIV = 32MHz */
#endif
/* AHB clock (HCLK) is SYSCLK (32MHz) */
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY /* Same as above, to satisfy compiler */
/* APB2 clock (PCLK2) is HCLK (32MHz) */
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
#define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY)
/* APB2 timers 9, 10, and 11 will receive PCLK2. */
#define STM32_APB2_TIM9_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM10_CLKIN (STM32_PCLK2_FREQUENCY)
#define STM32_APB2_TIM11_CLKIN (STM32_PCLK2_FREQUENCY)
/* APB1 clock (PCLK1) is HCLK (32MHz) */
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY)
/* APB1 timers 2-7 will receive PCLK1 */
#define STM32_APB1_TIM2_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM3_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM4_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM5_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM6_CLKIN (STM32_PCLK1_FREQUENCY)
#define STM32_APB1_TIM7_CLKIN (STM32_PCLK1_FREQUENCY)
/* LED definitions ******************************************************************/
/* The STM32L-Discovery board has four LEDs. Two of these are controlled by
* logic on the board and are not available for software control:
*
* LD1 COM: LD2 default status is red. LD2 turns to green to indicate that
* communications are in progress between the PC and the ST-LINK/V2.
* LD2 PWR: Red LED indicates that the board is powered.
*
* And two LEDs can be controlled by software:
*
* User LD3: Green LED is a user LED connected to the I/O PB7 of the STM32L152
* MCU.
* User LD4: Blue LED is a user LED connected to the I/O PB6 of the STM32L152
* MCU.
*
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any
* way. The following definitions are used to access individual LEDs.
*/
/* LED index values for use with board_userled() */
#define BOARD_LED1 0 /* User LD3 */
#define BOARD_LED2 1 /* User LD4 */
#define BOARD_NLEDS 2
/* LED bits for use with board_userled_all() */
#define BOARD_LED1_BIT (1 << BOARD_LED1)
#define BOARD_LED2_BIT (1 << BOARD_LED2)
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 8 LEDs on board the
* STM32L-Discovery. The following definitions describe how NuttX controls the LEDs:
*
* SYMBOL Meaning LED state
* LED1 LED2
* ------------------- ----------------------- -------- --------
* LED_STARTED NuttX has been started OFF OFF
* LED_HEAPALLOCATE Heap has been allocated OFF OFF
* LED_IRQSENABLED Interrupts enabled OFF OFF
* LED_STACKCREATED Idle stack created ON OFF
* LED_INIRQ In an interrupt No change
* LED_SIGNAL In a signal handler No change
* LED_ASSERTION An assertion failed No change
* LED_PANIC The system has crashed OFF Blinking
* LED_IDLE STM32 is is sleep mode Not used
*/
#define LED_STARTED 0
#define LED_HEAPALLOCATE 0
#define LED_IRQSENABLED 0
#define LED_STACKCREATED 1
#define LED_INIRQ 2
#define LED_SIGNAL 2
#define LED_ASSERTION 2
#define LED_PANIC 3
/* Button definitions ***************************************************************/
/* The STM32L-Discovery supports two buttons; only one button is controllable by
* software:
*
* B1 USER: user and wake-up button connected to the I/O PA0 of the STM32L152RBT6.
* B2 RESET: pushbutton connected to NRST is used to RESET the STM32L152RBT6.
*/
#define BUTTON_USER 0
#define NUM_BUTTONS 1
#define BUTTON_USER_BIT (1 << BUTTON_USER)
/* Alternate Pin Functions **********************************************************/
/* The STM32L-Discovery has no on-board RS-232 driver. Further, there are no USART
* pins that do not conflict with the on board resources, in particular, the LCD:
* Most USART pins are available if the LCD is enabled; USART2 may be used if either
* the LCD or the on-board LEDs are disabled.
*
* PA9 USART1_TX LCD glass COM1 P2, pin 22
* PA10 USART1_RX LCD glass COM2 P2, pin 21
* PB6 USART1_TX LED Blue P2, pin 8
* PB7 USART1_RX LED Green P2, pin 7
*
* PA2 USART2_TX LCD SEG1 P1, pin 17
* PA3 USART2_RX LCD SEG2 P1, pin 18
*
* PB10 USART3_TX LCD SEG6 P1, pin 22
* PB11 USART3_RX LCD SEG7 P1, pin 23
* PC10 USART3_TX LCD SEG22 P2, pin 15
* PC11 USART3_RX LCD SEG23 P2, pin 14
*/
#if !defined(CONFIG_STM32_LCD)
/* Select PA9 and PA10 if the LCD is not enabled */
# define GPIO_USART1_RX GPIO_USART1_RX_1 /* PA10 */
# define GPIO_USART1_TX GPIO_USART1_TX_1 /* PA9 */
/* This there are no other options for USART1 on this part */
# define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
# define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */
/* Arbirtrarily select PB10 and PB11 */
# define GPIO_USART3_RX GPIO_USART3_RX_1 /* PB11 */
# define GPIO_USART3_TX GPIO_USART3_TX_1 /* PB10 */
#elif !defined(CONFIG_ARCH_LEDS)
/* Select PB6 and PB7 if the LEDs are not enabled */
# define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */
# define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */
#endif
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/****************************************************************************
* Name: stm32_slcd_initialize
*
* Description:
* Initialize the STM32L-Discovery LCD hardware and register the character
* driver as /dev/slcd.
*
****************************************************************************/
#ifdef CONFIG_STM32_LCD
int stm32_slcd_initialize(void);
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIG_STM32LDISCOVERY_INCLUDE_BOARD_H */
Reference in New Issue View Git Blame Copy Permalink