232 lines
7.6 KiB
C
232 lines
7.6 KiB
C
/****************************************************************************
|
|
* configs/sama5d3-xplained/src/sam_nandflash.c
|
|
*
|
|
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Most of this file derives from Atmel sample code for the SAMA5D3-Xplained
|
|
* board. That sample code has licensing that is compatible with the NuttX
|
|
* modified BSD license:
|
|
*
|
|
* Copyright (c) 2012, Atmel Corporation
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor Atmel nor the names of its contributors may
|
|
* be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include <sys/mount.h>
|
|
#include <stdbool.h>
|
|
#include <stdint.h>
|
|
#include <errno.h>
|
|
#include <debug.h>
|
|
|
|
#include <nuttx/mtd/mtd.h>
|
|
#include <nuttx/fs/nxffs.h>
|
|
|
|
#include "up_arch.h"
|
|
#include "sam_periphclks.h"
|
|
#include "sam_pio.h"
|
|
#include "sam_nand.h"
|
|
#include "chip/sam_hsmc.h"
|
|
#include "chip/sam_pinmap.h"
|
|
|
|
#include "sama5d3-xplained.h"
|
|
|
|
#ifdef CONFIG_SAMA5_EBICS3_NAND
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Private Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: board_nandflash_config
|
|
*
|
|
* Description:
|
|
* If CONFIG_SAMA5_EBICS3_NAND is defined, then NAND FLASH support is
|
|
* enabled. This function provides the board-specific implementation of
|
|
* the logic to reprogram the SMC to support NAND FLASH on the specified
|
|
* CS.
|
|
*
|
|
* Input Parameters:
|
|
* cs - Chip select number (in the event that multiple NAND devices
|
|
* are connected on-board).
|
|
*
|
|
* Returned Values:
|
|
* OK if the HSMC was successfully configured for this CS. A negated
|
|
* errno value is returned on a failure. This would fail with -ENODEV,
|
|
* for example, if the board does not support NAND FLASH on the requested
|
|
* CS.
|
|
*
|
|
****************************************************************************/
|
|
|
|
int board_nandflash_config(int cs)
|
|
{
|
|
uint32_t regval;
|
|
|
|
/* The Embest and Ronetix CM boards and one Hynix NAND HY27UF(08/16)2G2B
|
|
* Series NAND (MT29F2G08ABAEAWP). This part has a capacity of 256Mx8bit
|
|
* () with spare 8Mx8 bit capacity. The device contains 2048 blocks, composed
|
|
* by 64 x 2112 byte pages. The effective size is approximately 256MiB.
|
|
*
|
|
* NAND is available on CS3.
|
|
*/
|
|
|
|
if (cs == HSMC_CS3)
|
|
{
|
|
/* Make sure that the SMC peripheral is enabled. */
|
|
|
|
sam_hsmc_enableclk();
|
|
|
|
/* Configure the SMC */
|
|
|
|
regval = HSMC_SETUP_NWE_SETUP(1) | HSMC_SETUP_NCS_WRSETUP(1) |
|
|
HSMC_SETUP_NRD_SETUP(2) | HSMC_SETUP_NCS_RDSETUP(1);
|
|
putreg32(regval, SAM_HSMC_SETUP(HSMC_CS3));
|
|
|
|
regval = HSMC_PULSE_NWE_PULSE(5) | HSMC_PULSE_NCS_WRPULSE(7) |
|
|
HSMC_PULSE_NRD_PULSE(5) | HSMC_PULSE_NCS_RDPULSE(7);
|
|
putreg32(regval, SAM_HSMC_PULSE(HSMC_CS3));
|
|
|
|
regval = HSMC_CYCLE_NWE_CYCLE(8) | HSMC_CYCLE_NRD_CYCLE(9);
|
|
putreg32(regval, SAM_HSMC_CYCLE(HSMC_CS3));
|
|
|
|
regval = HSMC_TIMINGS_TCLR(3) | HSMC_TIMINGS_TADL(10) |
|
|
HSMC_TIMINGS_TAR(3) | HSMC_TIMINGS_TRR(4) |
|
|
HSMC_TIMINGS_TWB(5) | HSMC_TIMINGS_RBNSEL(3) |
|
|
HSMC_TIMINGS_NFSEL;
|
|
putreg32(regval, SAM_HSMC_TIMINGS(HSMC_CS3));
|
|
|
|
regval = HSMC_MODE_READMODE | HSMC_MODE_WRITEMODE |
|
|
HSMC_MODE_BIT_8 | HSMC_MODE_TDFCYCLES(1);
|
|
putreg32(regval, SAM_HSMC_MODE(HSMC_CS3));
|
|
|
|
/* Configure NAND PIO pins
|
|
*
|
|
* NAND Interface:
|
|
*
|
|
* NCS3/NANDCE - Dedicated pin; no configuration needed
|
|
* NANDCLE - PE21
|
|
* NANDALE - PE22
|
|
* NRD/NANDOE - Dedicated pin; no configuration needed
|
|
* NWE/NANDWE - Dedicated pin; no configuration needed
|
|
* NANDRDY - Dedicated pin; no configuration needed
|
|
* M_EBI_D0-7 - Dedicated pins; no configuration needed
|
|
*/
|
|
|
|
sam_configpio(PIO_HSMC_NANDALE);
|
|
sam_configpio(PIO_HSMC_NANDCLE);
|
|
|
|
return OK;
|
|
}
|
|
|
|
return -ENODEV;
|
|
}
|
|
|
|
/****************************************************************************
|
|
* Name: sam_nand_automount
|
|
*
|
|
* Description:
|
|
* Initialize and configure the NAND on CS3
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef HAVE_NAND
|
|
int sam_nand_automount(int minor)
|
|
{
|
|
FAR struct mtd_dev_s *mtd;
|
|
static bool initialized = false;
|
|
int ret;
|
|
|
|
/* Have we already initialized? */
|
|
|
|
if (!initialized)
|
|
{
|
|
/* Create and initialize an NAND MATD device */
|
|
|
|
mtd = sam_nand_initialize(HSMC_CS3);
|
|
if (!mtd)
|
|
{
|
|
fdbg("ERROR: Failed to create the NAND driver on CS%d\n", HSMC_CS3);
|
|
return -ENODEV;
|
|
}
|
|
|
|
#if defined(CONFIG_SAMA5D3XPLAINED_NAND_FTL)
|
|
/* Use the FTL layer to wrap the MTD driver as a block driver */
|
|
|
|
ret = ftl_initialize(NAND_MINOR, mtd);
|
|
if (ret < 0)
|
|
{
|
|
fdbg("ERROR: Failed to initialize the FTL layer: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
#elif defined(CONFIG_SAMA5D3XPLAINED_NAND_NXFFS)
|
|
/* Initialize to provide NXFFS on the MTD interface */
|
|
|
|
ret = nxffs_initialize(mtd);
|
|
if (ret < 0)
|
|
{
|
|
fdbg("ERROR: NXFFS initialization failed: %d\n", ret);
|
|
return ret;
|
|
}
|
|
|
|
/* Mount the file system at /mnt/nand */
|
|
|
|
ret = mount(NULL, "/mnt/nand", "nxffs", 0, NULL);
|
|
if (ret < 0)
|
|
{
|
|
fdbg("ERROR: Failed to mount the NXFFS volume: %d\n", errno);
|
|
return ret;
|
|
}
|
|
#endif
|
|
/* Now we are initialized */
|
|
|
|
initialized = true;
|
|
}
|
|
|
|
return OK;
|
|
}
|
|
#endif
|
|
|
|
#endif /* CONFIG_SAMA5_EBICS3_NAND */
|