nuttx/configs/efm32-g8xx-stk/src/efm32-g8xx-stk.h

95 lines
4.3 KiB
C

/****************************************************************************
* configs/efm32-g8xx-stk/src/efm32-g8xx-stk.h
*
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
****************************************************************************/
#ifndef __CONFIGS_EFM32_G8XX_STK_SRC_EFM32_G8XX_STK_H
#define __CONFIGS_EFM32_G8XX_STK_SRC_EFM32_G8XX_STK_H
/****************************************************************************
* Included Files
****************************************************************************/
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* UART0
*
* The control MCU acts as a board controller (BC). There is a UART
* connection between the EFM and the BC. The connection is made by
* setting the EFM_BC_EN (PD13) line high. The EFM can then use the BSP to
* send commands to the BC. When EFM_BC_EN is low, EFM_BC_TX and EFM_BC_RX
* can be used by other applications.
*/
#ifdef CONFIG_EFM32G8STK_BCEN
# define GPIO_BC_EN (GPIO_OUTPUT_PUSHPULL|GPIO_OUTPUT_SET|\
GPIO_PORTD|GPIO_PIN13)
#else
# define GPIO_BC_EN (GPIO_OUTPUT_PUSHPULL|GPIO_OUTPUT_CLEAR|\
GPIO_PORTD|GPIO_PIN13)
#endif
/* LEDs
*
* The EFM32 Gecko Start Kit has four yellow LEDs. These LEDs are connected
* as follows:
*
* ------------------------------------- --------------------
* EFM32 PIN BOARD SIGNALS
* ------------------------------------- --------------------
* C0/USART1_TX#0/PCNT0_S0IN#2/ACMP0_CH0 MCU_PC0 UIF_LED0
* C1/USART1_RX#0/PCNT0_S1IN#2/ACMP0_CH1 MCU_PC1 UIF_LED1
* C2/USART2_TX#0/ACMP0_CH2 MCU_PC2 UIF_LED2
* C3/USART2_RX#0/ACMP0_CH3 MCU_PC3 UIF_LED3
* ------------------------------------- --------------------
*
* All LEDs are grounded and so are illuminated by outputting a high
* value to the LED.
*/
#define GPIO_LED0 (GPIO_OUTPUT_WIREDOR_PULLDOWN|\
GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN0)
#define GPIO_LED1 (GPIO_OUTPUT_WIREDOR_PULLDOWN|\
GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN1)
#define GPIO_LED2 (GPIO_OUTPUT_WIREDOR_PULLDOWN|\
GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN2)
#define GPIO_LED3 (GPIO_OUTPUT_WIREDOR_PULLDOWN|\
GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN3)
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
#endif /* __CONFIGS_EFM32_G8XX_STK_SRC_EFM32_G8XX_STK_H */