165 lines
5.7 KiB
Plaintext
165 lines
5.7 KiB
Plaintext
README for the XMC4500 Relax
|
|
============================
|
|
|
|
The directory provides board support for the Infinion XMC4500 Relax v1
|
|
boards. There are to variants of this board: There is a Lite version
|
|
that has fewer features, for example, no 32.768KHz crystal.
|
|
|
|
The current configurations support only the Lite version of the board.
|
|
|
|
Status
|
|
======
|
|
|
|
2017-03-21: The XMC4500 Relax boots into NSH, provides the NSH prompt,
|
|
and the LEDs are working. But there is a problem with sserial input.
|
|
The most likely reason for this is there are no serial RX interripts.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
Be default, UART0 (aka, USIC0, channel 0) is used as the serial console.
|
|
The RX and TX pins is available:
|
|
|
|
RX - P1.4, Connector X2, pin 17
|
|
TX - P1.5, Connector X2, pin 16
|
|
GND - Available on pins 1-4 of either connector X1 or X2
|
|
VDD3.3 - Available on pins 37-38 of either connector X1 or X2
|
|
VDD5 - Available on pins 39-40 of either connector X1 or X2
|
|
|
|
A TTL to RS-232 convertor or a USB TTL-to-USB serial adaptor is required.
|
|
The notion of what is TX and what is RX depends on your point of view.
|
|
With the TTL to RS-232 converter, I connect pin 17 to the pin labeled
|
|
TX on the converter and pin 16 to the RX pin on the converter.
|
|
|
|
LEDs
|
|
====
|
|
|
|
The XMC4500 Relax Lite v1 board has two LEDs:
|
|
|
|
LED1 P1.1 High output illuminates
|
|
LED2 P1.0 High output illuminates
|
|
|
|
If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
any way. The definitions provided in the board.h header file can be used
|
|
to access individual LEDs.
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/sam_autoleds.c. The LEDs are used to encode
|
|
OS-related events as follows:
|
|
|
|
SYMBOL Meaning LED state
|
|
LED1 LED2
|
|
------------------ ------------------------ ------ ------
|
|
LED_STARTED NuttX has been started OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF
|
|
LED_STACKCREATED Idle stack created ON OFF
|
|
LED_INIRQ In an interrupt No change
|
|
LED_SIGNAL In a signal handler No change
|
|
LED_ASSERTION An assertion failed No change
|
|
LED_PANIC The system has crashed N/C Blinking
|
|
LED_IDLE MCU is is sleep mode Not used
|
|
|
|
Thus if LED1 is statically on, NuttX has successfully booted and is,
|
|
apparently, running normally. If LED2 is flashing at approximately
|
|
2Hz, then a fatal error has been detected and the system has halted.
|
|
|
|
Buttons
|
|
=======
|
|
|
|
The XMC4500 Relax Lite v1 board has two buttons:
|
|
|
|
BUTTON1 P1.14 Low input sensed when button pressed
|
|
BUTTON2 P1.15 Low input sensed when button pressed
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Information Common to All Configurations
|
|
----------------------------------------
|
|
Each XMC4500 Relax configuration is maintained in a sub-directory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh xmc5400-relax/<subdir>
|
|
cd -
|
|
|
|
Before starting the build, make sure that your PATH environment variable
|
|
includes the correct path to your toolchain.
|
|
|
|
And then build NuttX by simply typing the following. At the conclusion of
|
|
the make, the nuttx binary will reside in an ELF file called, simply, nuttx.
|
|
|
|
make oldconfig
|
|
make
|
|
|
|
The <subdir> that is provided above as an argument to the tools/configure.sh
|
|
must be is one of the following.
|
|
|
|
NOTES:
|
|
|
|
1. These configurations use the mconf-based configuration tool. To
|
|
change any of these configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. Unless stated otherwise, all configurations generate console
|
|
output on UART0 (aka USIC0, channel 0) as described above under
|
|
"Serial Console". The relevant configuration settings are listed
|
|
below:
|
|
|
|
CONFIG_XMC4_USIC0=y
|
|
CONFIG_XMC4_USIC0_CHAN0_ISUART=y
|
|
CONFIG_XMC4_USIC0_CHAN1_NONE=y
|
|
|
|
CONFIG_UART0_SERIALDRIVER=y
|
|
CONFIG_UART0_SERIAL_CONSOLE=y
|
|
|
|
CONFIG_UART0_RXBUFSIZE=256
|
|
CONFIG_UART0_TXBUFSIZE=256
|
|
CONFIG_UART0_BAUD=115200
|
|
CONFIG_UART0_BITS=8
|
|
CONFIG_UART0_PARITY=0
|
|
CONFIG_UART0_2STOP=0
|
|
|
|
|
|
3. All of these configurations are set up to build under Windows using the
|
|
"GNU Tools for ARM Embedded Processors" that is maintained by ARM
|
|
(unless stated otherwise in the description of the configuration).
|
|
|
|
https://developer.arm.com/open-source/gnu-toolchain/gnu-rm
|
|
|
|
That toolchain selection can easily be reconfigured using
|
|
'make menuconfig'. Here are the relevant current settings:
|
|
|
|
Build Setup:
|
|
CONFIG_HOST_WINDOWS=y : Window environment
|
|
CONFIG_WINDOWS_CYGWIN=y : Cywin under Windows
|
|
|
|
System Type -> Toolchain:
|
|
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIW=y : GNU ARM EABI toolchain
|
|
|
|
Configuration sub-directories
|
|
-----------------------------
|
|
|
|
nsh:
|
|
|
|
Configures the NuttShell (nsh) located at examples/nsh. This
|
|
configuration is focused on low level, command-line driver testing. It
|
|
has no network.
|
|
|
|
NOTES:
|
|
|
|
1. NSH built-in applications are supported.
|
|
|
|
Binary Formats:
|
|
CONFIG_BUILTIN=y : Enable support for built-in programs
|
|
|
|
Application Configuration:
|
|
CONFIG_NSH_BUILTIN_APPS=y : Enable starting apps from NSH command line
|