112 lines
3.7 KiB
ReStructuredText
112 lines
3.7 KiB
ReStructuredText
==============
|
|
NXP S32K118EVB
|
|
==============
|
|
|
|
NXP S32K118EVB-Q064 is an evaluation board for the `NXP S32K118 MCU <https://www.nxp.com/products/processors-and-microcontrollers/s32-automotive-platform/s32k-general-purpose-mcus/s32k1-microcontrollers-for-general-purpose:S32K1>`_ based on an Arm Cortex-M0+ core.
|
|
|
|
Features
|
|
========
|
|
|
|
- NXP FS32K118LAT0MLHT MCU
|
|
- 48 MHz Clock (Max.)
|
|
- 256 Kb Flash
|
|
- 25 Kb SRAM
|
|
- 2 Kb EEPROM
|
|
|
|
- NXP UJA1169TK/F System Basis Chip
|
|
|
|
- Connectivity:
|
|
- OpenSDA UART (Console @ 115,200 baud)
|
|
- CAN 2.0 (Transceiver part of UJA1169 SBC)
|
|
- I/O headers with GPIO, I2C, SPI, etc.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
By default, the serial console will be provided on the OpenSDA VCOM port:
|
|
|
|
=============== ==== ==========
|
|
OpenSDA UART RX PTB0 LPUART0_RX
|
|
OpenSDA UART TX PTB1 LPUART0_TX
|
|
=============== ==== ==========
|
|
|
|
USB drivers for the PEmicro CDC Serial Port are available here: http://www.pemicro.com/opensda/
|
|
|
|
LEDs and Buttons
|
|
================
|
|
|
|
Leds
|
|
----
|
|
|
|
The S32K118EVB has one RGB LED:
|
|
|
|
======== ===== ========
|
|
RedLED PTD16 FTM0 CH1
|
|
GreenLED PTD15 FTM0 CH0
|
|
BlueLED PTE8 FTM0 CH6
|
|
======== ===== ========
|
|
|
|
An output of '1' illuminates the LED.
|
|
|
|
If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in any way. The following definitions are used to access individual RGB components (see s32k118evb.h):
|
|
|
|
- GPIO_LED_R
|
|
- GPIO_LED_G
|
|
- GPIO_LED_B
|
|
|
|
The RGB components could, alternatively, be controlled through PWM using the common RGB LED driver.
|
|
|
|
If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board the S32K118EVB. The following definitions describe how NuttX controls the LEDs:
|
|
|
|
================ ======================= ===== ===== ====
|
|
State Description RED GREEN BLUE
|
|
================ ======================= ===== ===== ====
|
|
LED_STARTED NuttX has been started OFF OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF ON
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF ON
|
|
LED_STACKCREATED Idle stack created OFF ON OFF
|
|
LED_INIRQ In an interrupt
|
|
LED_SIGNAL In a signal handler
|
|
LED_ASSERTION An assertion failed
|
|
LED_PANIC The system has crashed FLASH OFF OFF
|
|
LED_IDLE S32K118 in sleep mode
|
|
================ ======================= ===== ===== ====
|
|
|
|
Buttons
|
|
-------
|
|
|
|
The S32K118EVB supports two buttons:
|
|
|
|
=== ====
|
|
SW2 PTD3
|
|
SW3 PTD5
|
|
=== ====
|
|
|
|
OpenSDA Notes
|
|
=============
|
|
|
|
- USB drivers for the PEmicro CDC Serial Port are available here: http://www.pemicro.com/opensda/
|
|
- The drag'n'drog interface expects files in .srec format.
|
|
- Using Segger J-Link: Easy... but remember to use the SWD connector J14 near the touch electrodes and not the OpenSDA connector near the OpenSDA USB connector J7.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each S32K118EVB configuration is maintained in a sub-directory and can be selected as follows::
|
|
|
|
tools/configure.sh s32k118evb:<subdir>
|
|
|
|
Where <subdir> is one of the sub-directories listed in the next paragraph.
|
|
|
|
NOTES (common for all configurations):
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To change this configuration using that tool, you should:
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt. Also see additional README.txt files in the NuttX tools repository.
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the reconfiguration process.
|
|
|
|
2. Unless otherwise stated, the serial console used is LPUART1 at 115,200 8N1.
|
|
|
|
nsh
|
|
---
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. Support for builtin applications is enabled, but in the base configuration the only application selected is the "Hello, World!" example.
|