sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
16f8966fa9
nuttx/boards/xtensa/esp32s3/common/scripts/flat_memory.ld
Almir Okato d098c1dc87 esp32s3: add simple boot support 
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.

This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s3 targets and removes the need
for running 'make bootloader' command for it.

Other related fix, but not directly to Simple Boot:
- Instrumentation is required to run from IRAM to support it during
initialization. `is_eco0` function also needs to run from IRAM.
- `rtc.data` section placement was fixed.
- Provide arch-defined interfaces for efuses, in order to decouple
board config level from arch-defined values.

Signed-off-by: Almir Okato <almir.okato@espressif.com>
2024-04-17 19:43:05 +08:00

198 lines
7.5 KiB
Plaintext
Raw Blame History

/****************************************************************************
* boards/xtensa/esp32s3/common/scripts/flat_memory.ld
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/****************************************************************************
* ESP32-S3 Linker Script Memory Layout
*
* This file describes the memory layout (memory blocks) as virtual
* memory addresses.
*
* <legacy/mcuboot>_sections.ld contains output sections to link compiler
* output into these memory blocks.
*
****************************************************************************/
#include <nuttx/config.h>
#include "esp32s3_aliases.ld"
#define SRAM_IRAM_START 0x40370000
#define SRAM_DIRAM_I_START 0x40378000
/* The memory region starting from SRAM_IRAM_END up to 0x403dffff is
* reserved to the 2nd stage bootloader for actually loading the NuttX
* Application Image code and data into IRAM and DRAM. Otherwise the
* Bootloader could end up overwriting itself and failing to load the NuttX
* Application Image properly.
*
* For more information, refer to the bootloader linker scripts:
* https://github.com/espressif/esp-idf/blob/v5.1/components/bootloader/subproject/main/ld/esp32s3/bootloader.ld#L46-L52
*/
#ifdef CONFIG_ESP32S3_APP_FORMAT_MCUBOOT
#define SRAM_IRAM_END 0x403ba000
#elif defined (CONFIG_ESPRESSIF_SIMPLE_BOOT)
#define SRAM_IRAM_END 0x403c0000
#else
#define SRAM_IRAM_END 0x403cc700
#endif
#define I_D_SRAM_OFFSET (SRAM_DIRAM_I_START - SRAM_DRAM_START)
#define SRAM_DRAM_START 0x3fc88000
#define SRAM_DRAM_END (SRAM_IRAM_END - I_D_SRAM_OFFSET) /* 2nd stage bootloader iram_loader_seg start address */
#define I_D_SRAM_SIZE (SRAM_DRAM_END - SRAM_DRAM_START)
#define ICACHE_SIZE 0x8000
#define SRAM_IRAM_ORG (SRAM_IRAM_START + CONFIG_ESP32S3_INSTRUCTION_CACHE_SIZE)
#define SRAM_IRAM_SIZE (I_D_SRAM_SIZE + ICACHE_SIZE - CONFIG_ESP32S3_INSTRUCTION_CACHE_SIZE)
#define DCACHE_SIZE 0x10000
#define SRAM_DRAM_ORG (SRAM_DRAM_START)
#ifdef CONFIG_ESP32S3_FLASH_4M
# define FLASH_SIZE 0x400000
#elif defined (CONFIG_ESP32S3_FLASH_8M)
# define FLASH_SIZE 0x800000
#elif defined (CONFIG_ESP32S3_FLASH_16M)
# define FLASH_SIZE 0x1000000
#elif defined (CONFIG_ESP32S3_FLASH_32M)
# define FLASH_SIZE 0x2000000
#endif
#define RESERVE_RTC_MEM 24
MEMORY
{
#ifdef CONFIG_ESP32S3_APP_FORMAT_MCUBOOT
/* The origin values for "metadata" and "ROM" memory regions are the actual
* load addresses.
*
* NOTE: The memory region starting from 0x0 with length represented by
* CONFIG_ESP32S3_APP_MCUBOOT_HEADER_SIZE is reserved for the MCUboot header,
* which will be prepended to the binary file by the "imgtool" during the
* signing of firmware image.
*/
metadata (RX) : org = CONFIG_ESP32S3_APP_MCUBOOT_HEADER_SIZE, len = 0x20
ROM (RX) : org = ORIGIN(metadata) + LENGTH(metadata),
len = FLASH_SIZE - ORIGIN(ROM)
#elif defined (CONFIG_ESPRESSIF_SIMPLE_BOOT)
/* The 0x20 offset is a convenience for the app binary image generation.
* Flash cache has 64KB pages. The .bin file which is flashed to the chip
* has a 0x18 byte file header, and each segment has a 0x08 byte segment
* header. Setting this offset makes it simple to meet the flash cache MMU's
* constraint that (paddr % 64KB == vaddr % 64KB).
*/
ROM (RX) : org = 0x20,
len = FLASH_SIZE - ORIGIN(ROM)
#endif
/* Below values assume the flash cache is on, and have the blocks this
* uses subtracted from the length of the various regions. The 'data access
* port' dram/drom regions map to the same iram/irom regions but are
* connected to the data port of the CPU and eg allow bytewise access.
*/
/* IRAM for CPU */
iram0_0_seg (RX) : org = SRAM_IRAM_ORG, len = SRAM_IRAM_SIZE
/* Flash mapped instruction data. */
#ifdef CONFIG_ESP32S3_APP_FORMAT_MCUBOOT
irom0_0_seg (RX) : org = 0x42000000, len = FLASH_SIZE
#else
/* (See ROM segment above for meaning of 0x20 offset.) */
irom0_0_seg (RX) : org = 0x42000020, len = FLASH_SIZE - 0x20
#endif
/* Shared data RAM, excluding memory reserved for bootloader and ROM
* bss/data/stack.
*/
dram0_0_seg (RW) : org = SRAM_DRAM_ORG, len = I_D_SRAM_SIZE
/* Flash mapped constant data */
#ifdef CONFIG_ESP32S3_APP_FORMAT_MCUBOOT
/* The DROM segment origin is offset by 0x40 for mirroring the actual ROM
* image layout:
* 0x0 - 0x1F : MCUboot header
* 0x20 - 0x3F : Application image metadata section
* 0x40 onwards: ROM code and data
* This is required to meet the following constraint from the external
* flash MMU:
* VMA % 64KB == LMA % 64KB
* i.e. the lower 16 bits of both the virtual address (address seen by the
* CPU) and the load address (physical address of the external flash) must
* be equal.
*/
drom0_0_seg (R) : org = 0x3c000000 + ORIGIN(ROM),
len = FLASH_SIZE - ORIGIN(ROM)
#else
/* (See ROM segment above for meaning of 0x20 offset.) */
drom0_0_seg (R) : org = 0x3c000020, len = FLASH_SIZE - 0x20
#endif
/* RTC fast memory (executable). Persists over deep sleep. */
rtc_iram_seg(RWX) : org = 0x600fe000, len = 0x2000 - RESERVE_RTC_MEM
/* RTC fast memory (same block as above), viewed from data bus */
rtc_data_seg(RW) : org = 0x600fe000, len = 0x2000 - RESERVE_RTC_MEM
/* We reduced the size of rtc_iram_seg by RESERVE_RTC_MEM value.
It reserves the amount of RTC fast memory that we use for this memory segment.
This segment is intended for keeping:
- (lower addr) rtc timer data (s_rtc_timer_retain_mem, see esp_clk.c files).
- (higher addr) bootloader rtc data (s_bootloader_retain_mem, when a Kconfig option is on).
The aim of this is to keep data that will not be moved around and have a fixed address.
*/
rtc_reserved_seg(RW) : org = 0x600fe000 + 0x2000 - RESERVE_RTC_MEM, len = RESERVE_RTC_MEM
/* RTC slow memory (data accessible). Persists over deep sleep.
* Start of RTC slow memory is reserved for ULP co-processor code + data,
* if enabled.
*/
rtc_slow_seg(RW) : org = 0x50000000 + CONFIG_ESP32S3_ULP_COPROC_RESERVE_MEM,
len = 0x2000 - CONFIG_ESP32S3_ULP_COPROC_RESERVE_MEM
}
#ifdef CONFIG_ESP32S3_RUN_IRAM
REGION_ALIAS("default_rodata_seg", dram0_0_seg);
REGION_ALIAS("default_code_seg", iram0_0_seg);
#else
REGION_ALIAS("default_rodata_seg", drom0_0_seg);
REGION_ALIAS("default_code_seg", irom0_0_seg);
#endif /* CONFIG_ESP32S3_RUN_IRAM */
/* Mark the end of the RTC heap (top of the RTC region) */
_ertcheap = 0x50001fff;
Reference in New Issue View Git Blame Copy Permalink