sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
17cc0b9bfe
nuttx/configs/flipnclick-sam3x/src/flipnclick-sam3x.h

281 lines
11 KiB
C
Raw Blame History

/************************************************************************************
* configs/flipnclick-sam3x/src/flipnclick-sam3x.h
*
* Copyright (C) 2018 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_FLIPNCLICK_SAM3X_SRC_FLIPNCLICK_SAM3X_H
#define __CONFIGS_FLIPNCLICK_SAM3X_SRC_FLIPNCLICK_SAM3X_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/irq.h>
#include <nuttx/irq.h>
#include "chip/sam_pinmap.h"
/************************************************************************************
* Pre-processor Definitions
************************************************************************************/
/* Configuration ************************************************************/
#define HAVE_SSD1306 1
/* The SSD1306 LCD must be selected, installed on the Flip&Click, and must
* be configured to use the SPI interface.
*/
#if !defined(CONFIG_FLIPNCLICK_SAM3X_SSD1306) || \
!defined(CONFIG_LCD_SSD1306_SPI)
# undef HAVE_SSD1306
# undef CONFIG_FLIPNCLICK_SAM3X_SSD1306
# undef CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBA
# undef CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBB
# undef CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBC
# undef CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBD
#endif
/* There are four LEDs on the top, blue side of the board. Only one can be
* controlled by software:
*
* LED L - PB27 (PWM13)
*
* There are also four LEDs on the back, white side of the board:
*
* LED A - PC6
* LED B - PC5
* LED C - PC7
* LED D - PC8
*
* A high output value illuminates the LEDs.
*/
#define GPIO_LED_L (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOB | GPIO_PIN27)
#define GPIO_LED_A (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN6)
#define GPIO_LED_B (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN5)
#define GPIO_LED_C (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN7)
#define GPIO_LED_D (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN8)
/* SPI chip select pins.
*
* SPI0 is available on the Arduino compatible SPI connector (but no SPI is
* available on pins D10-D13 of the main Arduino Shield connectors where
* you might expect then). The SPI connector is configured as follows:
*
* Pin Board Signal SAM3X Pin Board Signal SAM3X
* --- ------------ ----- --- ------------ -----
* 1 SPI0_MISO PA25 2 VCC-5V N/A
* 3 SPI0_SCK PA27 4 SPI0_MOSI PA26
* 5 MRST NRSTB 6 GND N/A
*
* SPI0 is also available on each of the mikroBUS Click connectors (in
* addition to 5V and GND). The connectivity differs only in the chip
* select pin:
*
* MikroBUS A: MikroBUS B:
* Pin Board Signal SAM3X Pin Board Signal SAM3X
* ---- ------------ ----- ---- ------------ -----
* CS SPI0_CS0 PA28 CS PA29 PA29
* SCK SPI0_SCK PA27 SCK SPI0_SCK PA27
* MISO SPI0_MISO PA25 MISO SPI0_MISO PA25
* MOSI SPI0_MOSI PA26 MOSI SPI0_MOSI PA26
*
* MikroBUS C: MikroBUS D:
* Pin Board Signal SAM3X Pin Board Signal SAM3X
* ---- ------------ ----- ---- ------------ -----
* CS SPI0_CS2 PB21 CS SPI0_CS3 PB23
* SCK SPI0_SCK PA27 SCK SPI0_SCK PA27
* MISO SPI0_MISO PA25 MISO SPI0_MISO PA25
* MOSI SPI0_MOSI PA26 MOSI SPI0_MOSI PA26
*/
#define GPIO_MBA_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOA | GPIO_PIN28)
#define MBA_CSNUM 0
#define GPIO_MBB_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOA | GPIO_PIN29)
#define MBB_CSNUM 1
#define GPIO_MBC_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOB | GPIO_PIN21)
#define MBC_CSNUM 2
#define GPIO_MBD_CS (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_SET | \
GPIO_PORT_PIOB | GPIO_PIN23)
#define MBD_CSNUM 3
/* SSD1306 OLED
*
* The HiletGo is a 128x64 OLED that can be driven either via SPI or I2C (SPI
* is the default and is what is used here). I have mounted the OLED on a
* proto click board. The OLED is connected as follows:
*
* OLED ALIAS DESCRIPTION PROTO CLICK
* ----- ----------- ------------- -----------------
* GND Ground GND
* VCC Power Supply 5V (3-5V)
* D0 SCL,CLK,SCK Clock SCK
* D1 SDA,MOSI Data MOSI,SDI
* RES RST,RESET Reset RST (GPIO OUTPUT)
* DC AO Data/Command INT (GPIO OUTPUT)
* CS Chip Select CS (GPIO OUTPUT)
*
* NOTE that this is a write-only display (MOSI only)!
*
* MikroBUS A: MikroBUS B:
* Pin Board Signal SAM3X Pin Board Signal SAM3X
* ---- ------------ ----- ---- ------------ -------
* RST RSTA PC1 RST RSTB PC2
* DC INTA PD1 DC INTB PD2
*
* MikroBUS C: MikroBUS D:
* Pin Board Signal SAM3X Pin Board Signal SAM3X
* ---- ------------ ----- ---- ------------ -------
* RST RSTC PC3 RST RSTD PC4
* DC INTC PD3 DC INTD PD6
*/
#if defined(CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBA)
# ifndef CONFIG_SAM34_SPI0
# error "The OLED driver requires CONFIG_SAM34_SPI0 in the configuration"
# endif
# define SSD1306_SPI_BUS 0
# define SSD1306_CSNUM MBA_CSNUM
# define GPIO_SSD1306_CS GPIO_MBA_CS
# define GPIO_SSD1306_RST (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN1)
# define GPIO_SSD1306_DC (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOD | GPIO_PIN1)
#elif defined(CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBB)
# ifndef CONFIG_SAM34_SPI0
# error "The OLED driver requires CONFIG_SAM34_SPI0 in the configuration"
# endif
# define SSD1306_SPI_BUS 0
# define SSD1306_CSNUM MBB_CSNUM
# define GPIO_SSD1306_CS GPIO_MBB_CS
# define GPIO_SSD1306_RST (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN2)
# define GPIO_SSD1306_DC (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOD | GPIO_PIN2)
#elif defined(CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBC)
# ifndef CONFIG_SAM34_SPI0
# error "The OLED driver requires CONFIG_SAM34_SPI0 in the configuration"
# endif
# define SSD1306_SPI_BUS 0
# define SSD1306_CSNUM MBC_CSNUM
# define GPIO_SSD1306_CS GPIO_MBC_CS
# define GPIO_SSD1306_RST (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN3)
# define GPIO_SSD1306_DC (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOD | GPIO_PIN3)
#elif defined(CONFIG_FLIPNCLICK_SAM3X_SSD1306_MBD)
# ifndef CONFIG_SAM34_SPI0
# error "The OLED driver requires CONFIG_SAM34_SPI0 in the configuration"
# endif
# define SSD1306_SPI_BUS 0
# define SSD1306_CSNUM MBD_CSNUM
# define GPIO_SSD1306_CS GPIO_MBD_CS
# define GPIO_SSD1306_RST (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOC | GPIO_PIN4)
# define GPIO_SSD1306_DC (GPIO_OUTPUT | GPIO_CFG_DEFAULT | GPIO_OUTPUT_CLEAR | \
GPIO_PORT_PIOD | GPIO_PIN6)
#endif
/************************************************************************************
* Public Types
************************************************************************************/
/************************************************************************************
* Public data
************************************************************************************/
#ifndef __ASSEMBLY__
/************************************************************************************
* Public Functions
************************************************************************************/
/****************************************************************************
* Name: sam_bringup
*
* Description:
* Perform architecture-specific initialization
*
* CONFIG_BOARD_INITIALIZE=y :
* Called from board_initialize().
*
* CONFIG_BOARD_INITIALIZE=y && CONFIG_LIB_BOARDCTL=y :
* Called from the NSH library
*
****************************************************************************/
int sam_bringup(void);
/****************************************************************************
* Name: sam_graphics_setup
*
* Description:
* Called by either NX initialization logic (via board_graphics_setup) or
* directly from the board bring-up logic in order to configure the
* SSD1306 OLED.
*
****************************************************************************/
#ifdef HAVE_SSD1306
struct lcd_dev_s; /* Forward reference */
FAR struct lcd_dev_s *sam_graphics_setup(unsigned int devno);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __CONFIGS_FLIPNCLICK_SAM3X_SRC_FLIPNCLICK_SAM3X_H */
Reference in New Issue View Git Blame Copy Permalink