245 lines
11 KiB
ReStructuredText
245 lines
11 KiB
ReStructuredText
==================
|
|
Espressif ESP32-C3
|
|
==================
|
|
|
|
The ESP32-C3 is an ultra-low-power and highly integrated SoC with a RISC-V
|
|
core and supports 2.4 GHz Wi-Fi and Bluetooth Low Energy.
|
|
|
|
* Address Space
|
|
- 800 KB of internal memory address space accessed from the instruction bus
|
|
- 560 KB of internal memory address space accessed from the data bus
|
|
- 1016 KB of peripheral address space
|
|
- 8 MB of external memory virtual address space accessed from the instruction bus
|
|
- 8 MB of external memory virtual address space accessed from the data bus
|
|
- 480 KB of internal DMA address space
|
|
* Internal Memory
|
|
- 384 KB ROM
|
|
- 400 KB SRAM (16 KB can be configured as Cache)
|
|
- 8 KB of SRAM in RTC
|
|
* External Memory
|
|
- Up to 16 MB of external flash
|
|
* Peripherals
|
|
- 35 peripherals
|
|
* GDMA
|
|
- 7 modules are capable of DMA operations.
|
|
|
|
ESP32-C3 Toolchain
|
|
==================
|
|
|
|
A generic RISC-V toolchain can be used to build ESP32-C3 projects.
|
|
SiFive's toolchain can be downloaded from: https://github.com/sifive/freedom-tools/releases
|
|
|
|
Second stage bootloader and partition table
|
|
===========================================
|
|
|
|
The NuttX port for now relies on IDF's second stage bootloader to carry on some hardware
|
|
initializations. The binaries for the bootloader and the partition table can be found in
|
|
this repository: https://github.com/espressif/esp-nuttx-bootloader
|
|
That repository contains a dummy IDF project that's used to build the bootloader and
|
|
partition table, these are then presented as Github assets and can be downloaded
|
|
from: https://github.com/espressif/esp-nuttx-bootloader/releases
|
|
Download ``bootloader-esp32c3.bin`` and ``partition-table-esp32c3.bin`` and place them
|
|
in a folder, the path to this folder will be used later to program them. This
|
|
can be: ``../esp-bins``
|
|
|
|
Building and flashing
|
|
=====================
|
|
|
|
First make sure that ``esptool.py`` is installed. This tool is used to convert
|
|
the ELF to a compatible ESP32 image and to flash the image into the board.
|
|
It can be installed with: ``pip install esptool``.
|
|
|
|
Configure the NuttX project: ``./tools/configure.sh esp32c3-devkit:nsh``
|
|
Run ``make`` to build the project. Note that the conversion mentioned above is
|
|
included in the build process.
|
|
The ``esptool.py`` command to flash all the binaries is::
|
|
|
|
esptool.py --chip esp32c3 --port /dev/ttyUSBXX --baud 921600 write_flash 0x0 bootloader.bin 0x8000 partition-table.bin 0x10000 nuttx.bin
|
|
|
|
However, this is also included in the build process and we can build and flash with::
|
|
|
|
make flash ESPTOOL_PORT=<port> ESPTOOL_BINDIR=../esp-bins
|
|
|
|
Where ``<port>`` is typically ``/dev/ttyUSB0`` or similar and ``../esp-bins`` is
|
|
the path to the folder containing the bootloader and the partition table
|
|
for the ESP32-C3 as explained above.
|
|
Note that this step is required only one time. Once the bootloader and partition
|
|
table are flashed, we don't need to flash them again. So subsequent builds
|
|
would just require: ``make flash ESPTOOL_PORT=/dev/ttyUSBXX``
|
|
|
|
Debugging with OpenOCD
|
|
======================
|
|
|
|
Download and build OpenOCD from Espressif, that can be found in
|
|
https://github.com/espressif/openocd-esp32
|
|
|
|
If you have an ESP32-C3 ECO3, no external JTAG is required to debug, the ESP32-C3
|
|
integrates a USB-to-JTAG adapter.
|
|
|
|
OpenOCD can then be used::
|
|
|
|
openocd -c 'set ESP_RTOS none' -f board/esp32c3-builtin.cfg
|
|
|
|
For versions prior to ESP32-C3 ECO3, an external JTAG adapter is needed.
|
|
It can be connected as follows::
|
|
|
|
TMS -> GPIO4
|
|
TDI -> GPIO5
|
|
TCK -> GPIO6
|
|
TDO -> GPIO7
|
|
|
|
Furthermore, an efuse needs to be burnt to be able to debug::
|
|
|
|
espefuse.py -p <port> burn_efuse DIS_USB_JTAG
|
|
|
|
OpenOCD can then be used::
|
|
|
|
openocd -c 'set ESP_RTOS none' -f board/esp32c3-ftdi.cfg
|
|
|
|
Peripheral Support
|
|
==================
|
|
|
|
The following list indicates the state of peripherals' support in NuttX:
|
|
|
|
=========== ======= =====
|
|
Peripheral Support NOTES
|
|
=========== ======= =====
|
|
ADC Yes
|
|
AES Yes
|
|
Bluetooth Yes
|
|
CDC Console Yes Rev.3
|
|
DMA Yes
|
|
eFuse Yes
|
|
GPIO Yes
|
|
I2C Yes
|
|
LED_PWM Yes
|
|
RNG Yes
|
|
RSA Yes
|
|
RTC Yes
|
|
SHA Yes
|
|
SPI Yes
|
|
SPIFLASH Yes
|
|
Timers Yes
|
|
Touch Yes
|
|
UART Yes
|
|
Watchdog Yes
|
|
Wifi Yes
|
|
=========== ======= =====
|
|
|
|
Secure Boot and Flash Encryption
|
|
================================
|
|
|
|
Secure Boot
|
|
-----------
|
|
|
|
Secure Boot protects a device from running any unauthorized (i.e., unsigned) code by checking that
|
|
each piece of software that is being booted is signed. On an ESP32-C3, these pieces of software include
|
|
the second stage bootloader and each application binary. Note that the first stage bootloader does not
|
|
require signing as it is ROM code thus cannot be changed. This is achieved using specific hardware in
|
|
conjunction with MCUboot (read more about MCUboot `here <https://docs.mcuboot.com/>`__).
|
|
|
|
The Secure Boot process on the ESP32-C3 involves the following steps performed:
|
|
|
|
1. The first stage bootloader verifies the second stage bootloader's RSA-PSS signature. If the verification is successful,
|
|
the first stage bootloader loads and executes the second stage bootloader.
|
|
|
|
2. When the second stage bootloader loads a particular application image, the application's signature (RSA, ECDSA or ED25519) is verified
|
|
by MCUboot.
|
|
If the verification is successful, the application image is executed.
|
|
|
|
.. warning:: Once enabled, Secure Boot will not boot a modified bootloader. The bootloader will only boot an
|
|
application firmware image if it has a verified digital signature. There are implications for reflashing
|
|
updated images once Secure Boot is enabled. You can find more information about the ESP32-C3's Secure boot
|
|
`here <https://docs.espressif.com/projects/esp-idf/en/latest/esp32c3/security/secure-boot-v2.html>`__.
|
|
|
|
.. note:: As the bootloader image is built on top of the Hardware Abstraction Layer component
|
|
of `ESP-IDF <https://github.com/espressif/esp-idf>`_, the
|
|
`API port by Espressif <https://docs.mcuboot.com/readme-espressif.html>`_ will be used
|
|
by MCUboot rather than the original NuttX port.
|
|
|
|
Flash Encryption
|
|
----------------
|
|
|
|
Flash encryption is intended for encrypting the contents of the ESP32-C3's off-chip flash memory. Once this feature is enabled,
|
|
firmware is flashed as plaintext, and then the data is encrypted in place on the first boot. As a result, physical readout
|
|
of flash will not be sufficient to recover most flash contents.
|
|
|
|
.. warning:: After enabling Flash Encryption, an encryption key is generated internally by the device and
|
|
cannot be accessed by the user for re-encrypting data and re-flashing the system, hence it will be permanently encrypted.
|
|
Re-flashing an encrypted system is complicated and not always possible. You can find more information about the ESP32-C3's Flash Encryption
|
|
`here <https://docs.espressif.com/projects/esp-idf/en/latest/esp32c3/security/flash-encryption.html>`__.
|
|
|
|
Prerequisites
|
|
-------------
|
|
|
|
First of all, we need to install ``imgtool`` (a MCUboot utility application to manipulate binary
|
|
images) and ``esptool`` (the ESP32-C3 toolkit)::
|
|
|
|
$ pip install imgtool esptool
|
|
|
|
We also need to make sure that the python modules are added to ``PATH``::
|
|
|
|
$ echo "PATH=$PATH:/home/$USER/.local/bin" >> ~/.bashrc
|
|
|
|
Now, we will create a folder to store the generated keys (such as ``~/signing_keys``)::
|
|
|
|
$ mkdir ~/signing_keys && cd ~/signing_keys
|
|
|
|
With all set up, we can now generate keys to sign the bootloader and application binary images,
|
|
respectively, of the compiled project::
|
|
|
|
$ espsecure.py generate_signing_key --version 2 bootloader_signing_key.pem
|
|
$ imgtool keygen --key app_signing_key.pem --type rsa-3072
|
|
|
|
.. important:: The contents of the key files must be stored securely and kept secret.
|
|
|
|
Enabling Secure Boot and Flash Encryption
|
|
-----------------------------------------
|
|
|
|
To enable Secure Boot for the current project, go to the project's NuttX directory, execute ``make menuconfig`` and the following steps:
|
|
|
|
1. Enable experimental features in :menuselection:`Build Setup --> Show experimental options`;
|
|
|
|
2. Enable MCUboot in :menuselection:`Application Configuration --> Bootloader Utilities --> MCUboot`;
|
|
|
|
3. Change image type to ``MCUboot-bootable format`` in :menuselection:`System Type --> Application Image Configuration --> Application Image Format`;
|
|
|
|
4. Enable building MCUboot from the source code by selecting ``Build binaries from source``;
|
|
in :menuselection:`System Type --> Application Image Configuration --> Source for bootloader binaries`;
|
|
|
|
5. Enable Secure Boot in :menuselection:`System Type --> Application Image Configuration --> Enable hardware Secure Boot in bootloader`;
|
|
|
|
6. If you want to protect the SPI Bus against data sniffing, you can enable Flash Encryption in
|
|
:menuselection:`System Type --> Application Image Configuration --> Enable Flash Encryption on boot`.
|
|
|
|
Now you can design an update and confirm agent to your application. Check the `MCUboot design guide <https://docs.mcuboot.com/design.html>`_ and the
|
|
`MCUboot Espressif port documentation <https://docs.mcuboot.com/readme-espressif.html>`_ for
|
|
more information on how to apply MCUboot. Also check some `notes about the NuttX MCUboot port <https://github.com/mcu-tools/mcuboot/blob/main/docs/readme-nuttx.md>`_,
|
|
the `MCUboot porting guide <https://github.com/mcu-tools/mcuboot/blob/main/docs/PORTING.md>`_ and some
|
|
`examples of MCUboot applied in Nuttx applications <https://github.com/apache/nuttx-apps/tree/master/examples/mcuboot>`_.
|
|
|
|
After you developed an application which implements all desired functions, you need to flash it into the primary image slot
|
|
of the device (it will automatically be in the confirmed state, you can learn more about image
|
|
confirmation `here <https://docs.mcuboot.com/design.html#image-swapping>`_).
|
|
To flash to the primary image slot, select ``Application image primary slot`` in
|
|
:menuselection:`System Type --> Application Image Configuration --> Target slot for image flashing`
|
|
and compile it using ``make -j ESPSEC_KEYDIR=~/signing_keys``.
|
|
|
|
When creating update images, make sure to change :menuselection:`System Type --> Application Image Configuration --> Target slot for image flashing`
|
|
to ``Application image secondary slot``.
|
|
|
|
.. important:: When deploying your application, make sure to disable UART Download Mode by selecting ``Permanently disabled`` in
|
|
:menuselection:`System Type --> Application Image Configuration --> UART ROM download mode`
|
|
and change usage mode to ``Release`` in `System Type --> Application Image Configuration --> Enable usage mode`.
|
|
**After disabling UART Download Mode you will not be able to flash other images through UART.**
|
|
|
|
|
|
Supported Boards
|
|
================
|
|
|
|
.. toctree::
|
|
:glob:
|
|
:maxdepth: 1
|
|
|
|
boards/*/*
|