278 lines
8.7 KiB
ReStructuredText
278 lines
8.7 KiB
ReStructuredText
===============
|
||
i.MX RT1064 EVK
|
||
===============
|
||
|
||
`i.MX RT1064 EVK <https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/mimxrt1064-evk-i-mx-rt1064-evaluation-kit:MIMXRT1064-EVK>`_
|
||
is an evaluation kit by NXP company. This kit uses the i.MX RT1064 crossover MCU with ARM Cortex M7 core.
|
||
|
||
Features
|
||
========
|
||
|
||
- Processor
|
||
- MIMXRT1066DVL6A processor
|
||
- Memory
|
||
- 1 Mb OCRAM memory
|
||
- 256 Mb SDRAM memory
|
||
- 512 Mb Hyper Flash - Populated but 0 ohm DNP
|
||
- 64 Mb QSPI Flash
|
||
- TF socket for SD card
|
||
- Display and Audio
|
||
- Parallel LCD connector
|
||
- Camera connector
|
||
- Audio CODEC
|
||
- 4-pole audio headphone jack
|
||
- External speaker connection
|
||
- Microphone
|
||
- SPDIF connector
|
||
- Connectivity
|
||
- Micro USB host and OTG connectors
|
||
- Ethernet (10/100T) connector
|
||
- CAN transceivers
|
||
- Arduino® interface
|
||
- Sensors
|
||
- FXOS8700CQ 6-Axis Ecompass (3-Axis Mag, 3-Axis Accel)
|
||
|
||
Serial Console
|
||
==============
|
||
|
||
Virtual console port provided by OpenSDA:
|
||
|
||
========= ============= ==========
|
||
UART1_TXD GPIO_AD_B0_12 LPUART1_TX
|
||
UART1_RXD GPIO_AD_B0_13 LPUART1_RX
|
||
========= ============= ==========
|
||
|
||
Arduino RS-232 Shield:
|
||
|
||
=== == ======= ============= ==========
|
||
J22 D0 UART_RX GPIO_AD_B1_07 LPUART3_RX
|
||
J22 D1 UART_TX GPIO_AD_B1_06 LPUART3_TX
|
||
=== == ======= ============= ==========
|
||
|
||
LEDs and buttons
|
||
================
|
||
|
||
LEDs
|
||
----
|
||
|
||
There are four LED status indicators located on the EVK Board. The
|
||
functions of these LEDs include:
|
||
|
||
=== ============
|
||
Pin Description
|
||
=== ============
|
||
D3 Power Supply
|
||
D18 User LED
|
||
D20 OpenSDA
|
||
D21 Reset LED
|
||
=== ============
|
||
|
||
Only a single LED, D18, is under software control. It connects to
|
||
GPIO_AD_B0_09 which is shared with JTAG_TDI and ENET_RST
|
||
|
||
This LED is not used by the board port unless CONFIG_ARCH_LEDS is
|
||
defined. In that case, the usage by the board port is defined in
|
||
include/board.h and src/imxrt_autoleds.c. The LED is used to encode
|
||
OS-related events as follows:
|
||
|
||
================ ======================= =====
|
||
SYMBOL Meaning LED
|
||
================ ======================= =====
|
||
LED_STARTED NuttX has been started OFF
|
||
LED_HEAPALLOCATE Heap has been allocated OFF
|
||
LED_IRQSENABLED Interrupts enabled OFF
|
||
LED_STACKCREATED Idle stack created ON
|
||
LED_INIRQ In an interrupt N/C
|
||
LED_SIGNAL In a signal handler N/C
|
||
LED_ASSERTION An assertion failed N/C
|
||
LED_PANIC The system has crashed FLASH
|
||
================ ======================= =====
|
||
|
||
Thus if the LED is statically on, NuttX has successfully booted and is,
|
||
apparently, running normally. If the LED is flashing at approximately
|
||
2Hz, then a fatal error has been detected and the system has halted.
|
||
|
||
Buttons
|
||
-------
|
||
|
||
There are five user interface switches on the MIMXRT1050 EVK Board:
|
||
|
||
- SW1: Power Switch (slide switch fir power from J2)
|
||
- SW2: ON/OFF Button
|
||
- SW3: Power-on Reset button state forces to reset the system power except SNVS domain
|
||
- SW9: Reset button
|
||
- SW8: User button GPIO5-00
|
||
|
||
Only the user button is available to the software. It is sensed on the
|
||
WAKEUP pin which will be pulled low when the button is pressed.
|
||
|
||
|
||
J-Link External Debug Probe
|
||
===========================
|
||
|
||
Install the J-Link Debug Host Tools and make sure they are in your search path.
|
||
|
||
Attach a J-Link 20-pin connector to J21. Check that jumpers J47 and J48 are
|
||
off (they are on by default when boards ship from the factory) to ensure SWD
|
||
signals are disconnected from the OpenSDA microcontroller.
|
||
|
||
Configurations
|
||
==============
|
||
|
||
can
|
||
---
|
||
|
||
This is an nsh configuration (see below) with added support of CAN driver.
|
||
FlexCAN3 is chosen as default, the change can be made at System type peripheral
|
||
selection. Please note that only FlexCAN3 and FlexCAN2 is available on this board.
|
||
|
||
Bitrate and sample point can be also changed at System type peripheral selection,
|
||
basic values are 1 MHz for bitrate and 0.80 for sample point. The FlexCAN driver
|
||
for imxrt runs at 80 MHz clock frequency.
|
||
|
||
The configuration also includes CAN utilities as candump and cansend.
|
||
|
||
canfd
|
||
-----
|
||
|
||
This is an nsh configuration (see below) with added support of CAN_FD driver.
|
||
FlexCAN3 is chosen as default, please note that only FlexCAN3 is capable of
|
||
providing CAN_FD support.
|
||
|
||
Bitrate and sample point can be also changed at System type peripheral selection,
|
||
basic values are 1 MHz for bitrate and 0.80 for sample point for arbitration phase
|
||
and 4 MHz (bitrate) and 0.90 (sample point) for data phase. The FlexCAN driver
|
||
for imxrt runs at 80 MHz clock frequency.
|
||
|
||
The configuration also includes CAN utilities as candump and cansend.
|
||
|
||
knsh
|
||
----
|
||
|
||
This is identical to the nsh configuration below except that NuttX
|
||
is built as a protected mode, monolithic module and the user applications
|
||
are built separately. It is recommends to use a special make command;
|
||
not just 'make' but make with the following two arguments:
|
||
|
||
.. code-block:: console
|
||
|
||
$ make pass1 pass2
|
||
|
||
In the normal case (just 'make'), make will attempt to build both user-
|
||
and kernel-mode blobs more or less interleaved. This actual works!
|
||
However, for me it is very confusing so I prefer the above make command:
|
||
Make the user-space binaries first (pass1), then make the kernel-space
|
||
binaries (pass2)
|
||
|
||
NOTES:
|
||
|
||
At the end of the build, there will be several files in the top-level
|
||
NuttX build directory:
|
||
|
||
PASS1:
|
||
- nuttx_user.elf - The pass1 user-space ELF file
|
||
- nuttx_user.hex - The pass1 Intel HEX format file (selected in defconfig)
|
||
- User.map - Symbols in the user-space ELF file
|
||
|
||
PASS2:
|
||
- nuttx - The pass2 kernel-space ELF file
|
||
- nuttx.hex - The pass2 Intel HEX file (selected in defconfig)
|
||
- System.map - Symbols in the kernel-space ELF file
|
||
|
||
The J-Link programmer will except files in .hex, .mot, .srec, and .bin
|
||
formats.
|
||
|
||
Combining .hex files. If you plan to use the .hex files with your
|
||
debugger or FLASH utility, then you may need to combine the two hex
|
||
files into a single .hex file. Here is how you can do that.
|
||
|
||
The 'tail' of the nuttx.hex file should look something like this
|
||
(with my comments added beginning with #):
|
||
|
||
.. code-block:: console::
|
||
|
||
$ tail nuttx.hex
|
||
#xx xxxx 00 data records
|
||
...
|
||
:10 C93C 00 000000000040184000C2010000000000 90
|
||
:10 C94C 00 2400080000801B4000C01B4000001C40 5D
|
||
:10 C95C 00 00401C4000000C4050BF0060FF000100 74
|
||
#xx xxxx 05 Start Linear Address Record
|
||
:04 0000 05 6000 02C1 D4
|
||
#xx xxxx 01 End Of File record
|
||
:00 0000 01 FF
|
||
|
||
Use an editor such as vi to remove the 05 and 01 records.
|
||
|
||
The 'head' of the nuttx_user.hex file should look something like
|
||
this (again with my comments added beginning with #):
|
||
|
||
.. code-block:: console::
|
||
|
||
$ head nuttx_user.hex
|
||
#xx xxxx 04 Extended Linear Address Record
|
||
:02 0000 04 6020 7A
|
||
#xx xxxx 00 data records
|
||
:10 0000 00 8905206030002060F2622060FC622060 80
|
||
:10 0010 00 0000242008002420080024205C012420 63
|
||
:10 0020 00 140024203D0020603100206071052060 14
|
||
...
|
||
|
||
Nothing needs to be done here. The nuttx_user.hex file should
|
||
be fine.
|
||
|
||
Combine the edited nuttx.hex and un-edited nuttx_user.hex
|
||
file to produce a single combined hex file:
|
||
|
||
.. code-block:: console::
|
||
|
||
$ cat nuttx.hex nuttx_user.hex >combined.hex
|
||
|
||
Then use the combined.hex file with the to write the FLASH image.
|
||
If you do this a lot, you will probably want to invest a little time
|
||
to develop a tool to automate these steps.
|
||
|
||
STATUS: This configuration was added on 8 June 2018 primarily to assure
|
||
that all of the components are in place to support the PROTECTED mode
|
||
build. This configuration, however, has not been verified as of this
|
||
writing.
|
||
|
||
netnsh
|
||
------
|
||
|
||
This configuration is similar to the nsh configuration except that is
|
||
has networking enabled, both IPv4 and IPv6. This NSH configuration is
|
||
focused on network-related testing.
|
||
|
||
nsh
|
||
---
|
||
|
||
Configures the NuttShell (nsh) located at examples/nsh. This NSH
|
||
configuration is focused on low level, command-line driver testing.
|
||
Built-in applications are supported, but none are enabled. This
|
||
configuration does not support a network.
|
||
|
||
lvgl
|
||
----
|
||
|
||
Configures the Littlev graphic library (lvgl) demo located under
|
||
examples/lvgldemo. This configuration needs the optional LCD model
|
||
RK043FN02H-CT from NXP. The LCD panel comes with the integrated
|
||
capacitive touchscreen sensor FT5336GQQ connected to the LPI2C1 bus,
|
||
address 0x38. NuttX support such touchscreen device via the driver
|
||
ft5x06 (drivers/input/ft5x06.c). At the moment only the polling
|
||
method is available, the board features an interrupt line connected
|
||
to the touchscreen sensor IC.
|
||
|
||
IMXRT1064 MCU provides the integrated LCD driver.
|
||
|
||
The LCD panel features:
|
||
- size 4.3"
|
||
- resolution 480×272 RGB
|
||
- backlight driver
|
||
- dimensions [mm]: 105.5 (W) x 67.2(H) x 4.35(D) Max.
|
||
|
||
To run the lvgl demo please type "lvgldemo" at nsh prompt::
|
||
|
||
nsh> lvgldemo
|