1119 lines
44 KiB
Plaintext
1119 lines
44 KiB
Plaintext
README
|
|
======
|
|
|
|
This README discusses issues unique to NuttX configurations for the
|
|
STMicro STM3210E-EVAL development board.
|
|
|
|
Contents
|
|
========
|
|
|
|
- Development Environment
|
|
- GNU Toolchain Options
|
|
- IDEs
|
|
- NuttX EABI "buildroot" Toolchain
|
|
- NuttX OABI "buildroot" Toolchain
|
|
- NXFLAT Toolchain
|
|
- DFU and JTAG
|
|
- OpenOCD
|
|
- LEDs
|
|
- Temperature Sensor
|
|
- RTC
|
|
- FSMC SRAM
|
|
- STM3210E-EVAL-specific Configuration Options
|
|
- Configurations
|
|
|
|
Development Environment
|
|
=======================
|
|
|
|
Either Linux or Cygwin on Windows can be used for the development environment.
|
|
The source has been built only using the GNU toolchain (see below). Other
|
|
toolchains will likely cause problems. Testing was performed using the Cygwin
|
|
environment.
|
|
|
|
GNU Toolchain Options
|
|
=====================
|
|
|
|
The NuttX make system has been modified to support the following different
|
|
toolchain options.
|
|
|
|
1. The CodeSourcery GNU toolchain,
|
|
2. The devkitARM GNU toolchain,
|
|
3. Raisonance GNU toolchain, or
|
|
4. The NuttX buildroot Toolchain (see below).
|
|
|
|
All testing has been conducted using the NuttX buildroot toolchain. However,
|
|
the make system is setup to default to use the devkitARM toolchain. To use
|
|
the CodeSourcery, devkitARM or Raisonance GNU toolchain, you simply need to
|
|
add one of the following configuration options to your .config (or defconfig)
|
|
file:
|
|
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYL=y : CodeSourcery under Linux
|
|
CONFIG_ARMV7M_TOOLCHAIN_DEVKITARM=y : devkitARM under Windows
|
|
CONFIG_ARMV7M_TOOLCHAIN_RAISONANCE=y : Raisonance RIDE7 under Windows
|
|
CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
|
|
|
|
If you are not using CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT, then you may also have to modify
|
|
the PATH in the setenv.h file if your make cannot find the tools.
|
|
|
|
NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
|
|
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
|
|
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
|
|
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
|
|
|
|
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
|
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
|
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
|
|
|
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
|
are used in Nuttx (e.g., include/arch). The make system works around these
|
|
problems for the Windows tools by copying directories instead of linking them.
|
|
But this can also cause some confusion for you: For example, you may edit
|
|
a file in a "linked" directory and find that your changes had no effect.
|
|
That is because you are building the copy of the file in the "fake" symbolic
|
|
directory. If you use a Windows toolchain, you should get in the habit of
|
|
making like this:
|
|
|
|
make clean_context all
|
|
|
|
An alias in your .bashrc file might make that less painful.
|
|
|
|
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
|
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
|
-Os.
|
|
|
|
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
|
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
|
path or will get the wrong version of make.
|
|
|
|
IDEs
|
|
====
|
|
|
|
NuttX is built using command-line make. It can be used with an IDE, but some
|
|
effort will be required to create the project.
|
|
|
|
Makefile Build
|
|
--------------
|
|
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
|
simply use the NuttX makefile to build the system. That is almost for free
|
|
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
|
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
|
there is a lot of help on the internet).
|
|
|
|
Native Build
|
|
------------
|
|
Here are a few tips before you start that effort:
|
|
|
|
1) Select the toolchain that you will be using in your .config file
|
|
2) Start the NuttX build at least one time from the Cygwin command line
|
|
before trying to create your project. This is necessary to create
|
|
certain auto-generated files and directories that will be needed.
|
|
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
|
|
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
|
|
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
|
on the command line.
|
|
|
|
Startup files will probably cause you some headaches. The NuttX startup file
|
|
is arch/arm/src/stm32/stm32_vectors.S. You may have to build NuttX
|
|
one time from the Cygwin command line in order to obtain the pre-built
|
|
startup object needed by an IDE.
|
|
|
|
NuttX EABI "buildroot" Toolchain
|
|
================================
|
|
|
|
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
|
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
|
different from the default in your PATH variable).
|
|
|
|
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
|
Bitbucket download site (https://bitbucket.org/nuttx/buildroot/downloads/).
|
|
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
|
|
|
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
|
|
|
cd tools
|
|
./configure.sh stm3210e-eval/<sub-dir>
|
|
|
|
2. Download the latest buildroot package into <some-dir>
|
|
|
|
3. unpack the buildroot tarball. The resulting directory may
|
|
have versioning information on it like buildroot-x.y.z. If so,
|
|
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
|
|
|
4. cd <some-dir>/buildroot
|
|
|
|
5. cp configs/cortexm3-eabi-defconfig-4.6.3 .config
|
|
|
|
6. make oldconfig
|
|
|
|
7. make
|
|
|
|
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
|
the path to the newly built binaries.
|
|
|
|
See the file configs/README.txt in the buildroot source tree. That has more
|
|
details PLUS some special instructions that you will need to follow if you are
|
|
building a Cortex-M3 toolchain for Cygwin under Windows.
|
|
|
|
NOTE: Unfortunately, the 4.6.3 EABI toolchain is not compatible with the
|
|
the NXFLAT tools. See the top-level TODO file (under "Binary loaders") for
|
|
more information about this problem. If you plan to use NXFLAT, please do not
|
|
use the GCC 4.6.3 EABI toochain; instead use the GCC 4.3.3 OABI toolchain.
|
|
See instructions below.
|
|
|
|
NuttX OABI "buildroot" Toolchain
|
|
================================
|
|
|
|
The older, OABI buildroot toolchain is also available. To use the OABI
|
|
toolchain:
|
|
|
|
1. When building the buildroot toolchain, either (1) modify the cortexm3-eabi-defconfig-4.6.3
|
|
configuration to use EABI (using 'make menuconfig'), or (2) use an exising OABI
|
|
configuration such as cortexm3-defconfig-4.3.3
|
|
|
|
2. Modify the Make.defs file to use the OABI conventions:
|
|
|
|
+CROSSDEV = arm-nuttx-elf-
|
|
+ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
|
|
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-gotoff.ld -no-check-sections
|
|
-CROSSDEV = arm-nuttx-eabi-
|
|
-ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
|
|
-NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections
|
|
|
|
NXFLAT Toolchain
|
|
================
|
|
|
|
If you are *not* using the NuttX buildroot toolchain and you want to use
|
|
the NXFLAT tools, then you will still have to build a portion of the buildroot
|
|
tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can
|
|
be downloaded from the NuttX Bitbucket download site
|
|
(https://bitbucket.org/nuttx/nuttx/downloads/).
|
|
|
|
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
|
|
|
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
|
|
|
cd tools
|
|
./configure.sh lpcxpresso-lpc1768/<sub-dir>
|
|
|
|
2. Download the latest buildroot package into <some-dir>
|
|
|
|
3. unpack the buildroot tarball. The resulting directory may
|
|
have versioning information on it like buildroot-x.y.z. If so,
|
|
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
|
|
|
4. cd <some-dir>/buildroot
|
|
|
|
5. cp configs/cortexm3-defconfig-nxflat .config
|
|
|
|
6. make oldconfig
|
|
|
|
7. make
|
|
|
|
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
|
the path to the newly builtNXFLAT binaries.
|
|
|
|
DFU and JTAG
|
|
============
|
|
|
|
Enbling Support for the DFU Bootloader
|
|
--------------------------------------
|
|
The linker files in these projects can be configured to indicate that you
|
|
will be loading code using STMicro built-in USB Device Firmware Upgrade (DFU)
|
|
loader or via some JTAG emulator. You can specify the DFU bootloader by
|
|
adding the following line:
|
|
|
|
CONFIG_STM32_DFU=y
|
|
|
|
to your .config file. Most of the configurations in this directory are set
|
|
up to use the DFU loader.
|
|
|
|
If CONFIG_STM32_DFU is defined, the code will not be positioned at the beginning
|
|
of FLASH (0x08000000) but will be offset to 0x08003000. This offset is needed
|
|
to make space for the DFU loader and 0x08003000 is where the DFU loader expects
|
|
to find new applications at boot time. If you need to change that origin for some
|
|
other bootloader, you will need to edit the file(s) ld.script.dfu for the
|
|
configuration.
|
|
|
|
The DFU SE PC-based software is available from the STMicro website,
|
|
http://www.st.com. General usage instructions:
|
|
|
|
1. Convert the NuttX Intel Hex file (nuttx.hex) into a special DFU
|
|
file (nuttx.dfu)... see below for details.
|
|
2. Connect the STM3210E-EVAL board to your computer using a USB
|
|
cable.
|
|
3. Start the DFU loader on the STM3210E-EVAL board. You do this by
|
|
resetting the board while holding the "Key" button. Windows should
|
|
recognize that the DFU loader has been installed.
|
|
3. Run the DFU SE program to load nuttx.dfu into FLASH.
|
|
|
|
What if the DFU loader is not in FLASH? The loader code is available
|
|
inside of the Demo dirctory of the USBLib ZIP file that can be downloaded
|
|
from the STMicro Website. You can build it using RIDE (or other toolchains);
|
|
you will need a JTAG emulator to burn it into FLASH the first time.
|
|
|
|
In order to use STMicro's built-in DFU loader, you will have to get
|
|
the NuttX binary into a special format with a .dfu extension. The
|
|
DFU SE PC_based software installation includes a file "DFU File Manager"
|
|
conversion program that a file in Intel Hex format to the special DFU
|
|
format. When you successfully build NuttX, you will find a file called
|
|
nutt.hex in the top-level directory. That is the file that you should
|
|
provide to the DFU File Manager. You will end up with a file called
|
|
nuttx.dfu that you can use with the STMicro DFU SE program.
|
|
|
|
Enabling JTAG
|
|
-------------
|
|
If you are not using the DFU, then you will probably also need to enable
|
|
JTAG support. By default, all JTAG support is disabled but there NuttX
|
|
configuration options to enable JTAG in various different ways.
|
|
|
|
These configurations effect the setting of the SWJ_CFG[2:0] bits in the AFIO
|
|
MAPR register. These bits are used to configure the SWJ and trace alternate function I/Os. The SWJ (SerialWire JTAG) supports JTAG or SWD access to the
|
|
Cortex debug port. The default state in this port is for all JTAG support
|
|
to be disable.
|
|
|
|
CONFIG_STM32_JTAG_FULL_ENABLE - sets SWJ_CFG[2:0] to 000 which enables full
|
|
SWJ (JTAG-DP + SW-DP)
|
|
|
|
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - sets SWJ_CFG[2:0] to 001 which enable
|
|
full SWJ (JTAG-DP + SW-DP) but without JNTRST.
|
|
|
|
CONFIG_STM32_JTAG_SW_ENABLE - sets SWJ_CFG[2:0] to 010 which would set JTAG-DP
|
|
disabled and SW-DP enabled
|
|
|
|
The default setting (none of the above defined) is SWJ_CFG[2:0] set to 100
|
|
which disable JTAG-DP and SW-DP.
|
|
|
|
OpenOCD
|
|
=======
|
|
|
|
I have also used OpenOCD with the STM3210E-EVAL. In this case, I used
|
|
the Olimex USB ARM OCD. See the script in configs/stm3210e-eval/tools/oocd.sh
|
|
for more information. Using the script:
|
|
|
|
1) Start the OpenOCD GDB server
|
|
|
|
cd <nuttx-build-directory>
|
|
configs/stm3210e-eval/tools/oocd.sh $PWD
|
|
|
|
2) Load Nuttx
|
|
|
|
cd <nuttx-built-directory>
|
|
arm-none-eabi-gdb nuttx
|
|
gdb> target remote localhost:3333
|
|
gdb> mon reset
|
|
gdb> mon halt
|
|
gdb> load nuttx
|
|
|
|
3) Running NuttX
|
|
|
|
gdb> mon reset
|
|
gdb> c
|
|
|
|
LEDs
|
|
====
|
|
|
|
The STM3210E-EVAL board has four LEDs labeled LD1, LD2, LD3 and LD4 on the
|
|
board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related
|
|
events as follows:
|
|
|
|
SYMBOL Meaning LED1* LED2 LED3 LED4
|
|
---------------- ----------------------- ----- ----- ----- -----
|
|
LED_STARTED NuttX has been started ON OFF OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
|
|
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
|
|
LED_STACKCREATED Idle stack created OFF OFF ON OFF
|
|
LED_INIRQ In an interrupt** ON N/C N/C OFF
|
|
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
|
|
LED_ASSERTION An assertion failed ON ON N/C OFF
|
|
LED_PANIC The system has crashed N/C N/C N/C ON
|
|
LED_IDLE STM32 is is sleep mode (Optional, not used)
|
|
|
|
* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
|
|
and these LEDs will give you some indication of where the failure was
|
|
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
|
|
is because of timer interrupts that result in the LED being illuminated
|
|
on a small proportion of the time.
|
|
*** LED2 may also flicker normally if signals are processed.
|
|
|
|
Temperature Sensor
|
|
==================
|
|
|
|
LM-75 Temperature Sensor Driver
|
|
-------------------------------
|
|
Support for the on-board LM-75 temperature sensor is available. This
|
|
support has been verified, but has not been included in any of the
|
|
available the configurations. To set up the temperature sensor, add the
|
|
following to the NuttX configuration file
|
|
|
|
Drivers -> Sensors
|
|
CONFIG_LM75=y
|
|
CONFIG_I2C_LM75=y
|
|
|
|
Then you can implement logic like the following to use the temperature
|
|
sensor:
|
|
|
|
#include <nuttx/sensors/lm75.h>
|
|
#include <arch/board/board.h>
|
|
|
|
ret = stm32_lm75initialize("/dev/temp"); /* Register the temperature sensor */
|
|
fd = open("/dev/temp", O_RDONLY); /* Open the temperature sensor device */
|
|
ret = ioctl(fd, SNIOC_FAHRENHEIT, 0); /* Select Fahrenheit */
|
|
bytesread = read(fd, buffer, 8*sizeof(b16_t)); /* Read temperature samples */
|
|
|
|
More complex temperature sensor operations are also available. See the
|
|
IOCTL commands enumerated in include/nuttx/sensors/lm75.h. Also read the
|
|
escriptions of the stm32_lm75initialize() and stm32_lm75attach()
|
|
interfaces in the arch/board/board.h file (sames as
|
|
configs/stm3210e-eval/include/board.h).
|
|
|
|
NSH Command Line Application
|
|
----------------------------
|
|
There is a tiny NSH command line application at examples/system/lm75 that
|
|
will read the current temperature from an LM75 compatible temperature sensor
|
|
and print the temperature on stdout in either units of degrees Fahrenheit or
|
|
Centigrade. This tiny command line application is enabled with the following
|
|
configuration options:
|
|
|
|
Library
|
|
CONFIG_LIBM=y
|
|
CONFIG_LIBC_FLOATINGPOINT=y
|
|
|
|
Applications -> NSH Library
|
|
CONFIG_NSH_ARCHINIT=y
|
|
|
|
Applications -> System Add-Ons
|
|
CONFIG_SYSTEM_LM75=y
|
|
CONFIG_SYSTEM_LM75_DEVNAME="/dev/temp"
|
|
CONFIG_SYSTEM_LM75_FAHRENHEIT=y (or CENTIGRADE)
|
|
CONFIG_SYSTEM_LM75_STACKSIZE=1024
|
|
CONFIG_SYSTEM_LM75_PRIORITY=100
|
|
|
|
RTC
|
|
===
|
|
|
|
The STM32 RTC may configured using the following settings.
|
|
|
|
CONFIG_RTC - Enables general support for a hardware RTC. Specific
|
|
architectures may require other specific settings.
|
|
CONFIG_RTC_HIRES - The typical RTC keeps time to resolution of 1
|
|
second, usually supporting a 32-bit time_t value. In this case,
|
|
the RTC is used to "seed" the normal NuttX timer and the
|
|
NuttX timer provides for higher resoution time. If CONFIG_RTC_HIRES
|
|
is enabled in the NuttX configuration, then the RTC provides higher
|
|
resolution time and completely replaces the system timer for purpose of
|
|
date and time.
|
|
CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the
|
|
frequency of the high resolution RTC must be provided. If CONFIG_RTC_HIRES
|
|
is not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
|
|
CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an alarm.
|
|
A callback function will be executed when the alarm goes off
|
|
|
|
In hi-res mode, the STM32 RTC operates only at 16384Hz. Overflow interrupts
|
|
are handled when the 32-bit RTC counter overflows every 3 days and 43 minutes.
|
|
A BKP register is incremented on each overflow interrupt creating, effectively,
|
|
a 48-bit RTC counter.
|
|
|
|
In the lo-res mode, the RTC operates at 1Hz. Overflow interrupts are not handled
|
|
(because the next overflow is not expected until the year 2106.
|
|
|
|
WARNING: Overflow interrupts are lost whenever the STM32 is powered down. The
|
|
overflow interrupt may be lost even if the STM32 is powered down only momentarily.
|
|
Therefore hi-res solution is only useful in systems where the power is always on.
|
|
|
|
FSMC SRAM
|
|
=========
|
|
|
|
The 8-Mbit SRAM is connected to the STM32 at PG10 which will be FSMC_NE3, Bank1
|
|
SRAM3. This memory will appear at address 0x68000000.
|
|
|
|
The on-board SRAM can be configured by setting
|
|
|
|
CONFIG_STM32_FSMC=y : Enables the FSMC
|
|
CONFIG_STM32_FSMC_SRAM=y : Enable external SRAM support
|
|
CONFIG_HEAP2_BASE=0x68000000 : SRAM will be located at 0x680000000
|
|
CONFIG_HEAP2_SIZE=1048576 : The size of the SRAM is 1Mbyte
|
|
CONFIG_MM_REGIONS=2 : There will be two memory regions
|
|
: in the heap
|
|
|
|
STM3210E-EVAL-specific Configuration Options
|
|
============================================
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM3=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=stm32
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_STM32F103ZE
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
|
|
configuration features.
|
|
|
|
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=stm3210e_eval (for the STM3210E-EVAL development board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_STM3210E_EVAL=y
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_RAM_SIZE=0x00010000 (64Kb)
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_RAM_START=0x20000000
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
Individual subsystems can be enabled:
|
|
AHB
|
|
---
|
|
CONFIG_STM32_DMA1
|
|
CONFIG_STM32_DMA2
|
|
CONFIG_STM32_CRC
|
|
CONFIG_STM32_FSMC
|
|
CONFIG_STM32_SDIO
|
|
|
|
APB1
|
|
----
|
|
CONFIG_STM32_TIM2
|
|
CONFIG_STM32_TIM3
|
|
CONFIG_STM32_TIM4
|
|
CONFIG_STM32_TIM5
|
|
CONFIG_STM32_TIM6
|
|
CONFIG_STM32_TIM7
|
|
CONFIG_STM32_WWDG
|
|
CONFIG_STM32_IWDG
|
|
CONFIG_STM32_SPI2
|
|
CONFIG_STM32_SPI4
|
|
CONFIG_STM32_USART2
|
|
CONFIG_STM32_USART3
|
|
CONFIG_STM32_UART4
|
|
CONFIG_STM32_UART5
|
|
CONFIG_STM32_I2C1
|
|
CONFIG_STM32_I2C2
|
|
CONFIG_STM32_USB
|
|
CONFIG_STM32_CAN1
|
|
CONFIG_STM32_BKP
|
|
CONFIG_STM32_PWR
|
|
CONFIG_STM32_DAC1
|
|
CONFIG_STM32_DAC2
|
|
CONFIG_STM32_USB
|
|
|
|
APB2
|
|
----
|
|
CONFIG_STM32_ADC1
|
|
CONFIG_STM32_ADC2
|
|
CONFIG_STM32_TIM1
|
|
CONFIG_STM32_SPI1
|
|
CONFIG_STM32_TIM8
|
|
CONFIG_STM32_USART1
|
|
CONFIG_STM32_ADC3
|
|
|
|
Timer and I2C devices may need to the following to force power to be applied
|
|
unconditionally at power up. (Otherwise, the device is powered when it is
|
|
initialized).
|
|
|
|
CONFIG_STM32_FORCEPOWER
|
|
|
|
Timer devices may be used for different purposes. One special purpose is
|
|
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
|
|
is defined (as above) then the following may also be defined to indicate that
|
|
the timer is intended to be used for pulsed output modulation, ADC conversion,
|
|
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
|
|
to assign the timer (n) for used by the ADC or DAC, but then you also have to
|
|
configure which ADC or DAC (m) it is assigned to.
|
|
|
|
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,8
|
|
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,8
|
|
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,8, m=1,..,3
|
|
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,8
|
|
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,8, m=1,..,2
|
|
|
|
For each timer that is enabled for PWM usage, we need the following additional
|
|
configuration settings:
|
|
|
|
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
|
|
|
|
NOTE: The STM32 timers are each capable of generating different signals on
|
|
each of the four channels with different duty cycles. That capability is
|
|
not supported by this driver: Only one output channel per timer.
|
|
|
|
Alternate pin mappings. The STM3210E-EVAL board requires only CAN1 remapping
|
|
On the STM3210E-EVAL board pin PB9 is wired as TX and pin PB8 is wired as RX.
|
|
Which then makes the proper connection through the CAN transiver SN65HVD230
|
|
out to the CAN D-type 9-pn male connector where pin 2 is CANL and pin 7 is CANH.
|
|
|
|
CONFIG_STM32_TIM1_FULL_REMAP
|
|
CONFIG_STM32_TIM1_PARTIAL_REMAP
|
|
CONFIG_STM32_TIM2_FULL_REMAP
|
|
CONFIG_STM32_TIM2_PARTIAL_REMAP_1
|
|
CONFIG_STM32_TIM2_PARTIAL_REMAP_2
|
|
CONFIG_STM32_TIM3_FULL_REMAP
|
|
CONFIG_STM32_TIM3_PARTIAL_REMAP
|
|
CONFIG_STM32_TIM4_REMAP
|
|
CONFIG_STM32_USART1_REMAP
|
|
CONFIG_STM32_USART2_REMAP
|
|
CONFIG_STM32_USART3_FULL_REMAP
|
|
CONFIG_STM32_USART3_PARTIAL_REMAP
|
|
CONFIG_STM32_SPI1_REMAP
|
|
CONFIG_STM32_SPI3_REMAP
|
|
CONFIG_STM32_I2C1_REMAP
|
|
CONFIG_STM32_CAN1_REMAP1
|
|
CONFIG_STM32_CAN1_REMAP2
|
|
CONFIG_STM32_CAN2_REMAP
|
|
|
|
JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):
|
|
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
|
|
but without JNTRST.
|
|
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
|
|
|
|
STM32F103Z specific device driver settings
|
|
|
|
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
|
|
m (m=4,5) for the console and ttys0 (default is the USART1).
|
|
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_U[S]ARTn_2STOP - Two stop bits
|
|
|
|
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
|
|
support. Non-interrupt-driven, poll-waiting is recommended if the
|
|
interrupt rate would be to high in the interrupt driven case.
|
|
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
|
|
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
|
|
|
|
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
|
|
and CONFIG_STM32_DMA2.
|
|
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
|
|
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
|
|
Default: Medium
|
|
CONFIG_STM32_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
|
|
4-bit transfer mode.
|
|
|
|
STM3210E-EVAL CAN Configuration
|
|
|
|
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
|
|
CONFIG_STM32_CAN2 must also be defined)
|
|
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
|
|
Standard 11-bit IDs.
|
|
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
|
|
Default: 8
|
|
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
|
|
Default: 4
|
|
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
|
|
mode for testing. The STM32 CAN driver does support loopback mode.
|
|
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
|
|
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
|
|
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
|
|
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
|
|
CONFIG_STM32_CAN_REGDEBUG - If CONFIG_DEBUG_FEATURES is set, this will generate an
|
|
dump of all CAN registers.
|
|
|
|
STM3210E-EVAL LCD Hardware Configuration
|
|
|
|
CONFIG_LCD_LANDSCAPE - Define for 320x240 display "landscape"
|
|
support. Default is this 320x240 "landscape" orientation
|
|
(this setting is informative only... not used).
|
|
CONFIG_LCD_PORTRAIT - Define for 240x320 display "portrait"
|
|
orientation support. In this orientation, the STM3210E-EVAL's
|
|
LCD ribbon cable is at the bottom of the display. Default is
|
|
320x240 "landscape" orientation.
|
|
CONFIG_LCD_RPORTRAIT - Define for 240x320 display "reverse
|
|
portrait" orientation support. In this orientation, the
|
|
STM3210E-EVAL's LCD ribbon cable is at the top of the display.
|
|
Default is 320x240 "landscape" orientation.
|
|
CONFIG_STM3210E_LCD_BACKLIGHT - Define to support a backlight.
|
|
CONFIG_STM3210E_LCD_PWM - If CONFIG_STM32_TIM1 is also defined, then an
|
|
adjustable backlight will be provided using timer 1 to generate
|
|
various pulse widthes. The granularity of the settings is
|
|
determined by CONFIG_LCD_MAXPOWER. If CONFIG_STM3210E_LCD_PWM (or
|
|
CONFIG_STM32_TIM1) is not defined, then a simple on/off backlight
|
|
is provided.
|
|
CONFIG_STM3210E_LCD_RDSHIFT - When reading 16-bit gram data, there appears
|
|
to be a shift in the returned data. This value fixes the offset.
|
|
Default 5.
|
|
|
|
The LCD driver dynamically selects the LCD based on the reported LCD
|
|
ID value. However, code size can be reduced by suppressing support for
|
|
individual LCDs using:
|
|
|
|
CONFIG_STM3210E_AM240320_DISABLE
|
|
CONFIG_STM3210E_SPFD5408B_DISABLE
|
|
CONFIG_STM3210E_R61580_DISABLE
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Each STM3210E-EVAL configuration is maintained in a sub-directory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh stm3210e-eval/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
composite
|
|
---------
|
|
|
|
This configuration exercises a composite USB interface consisting
|
|
of a CDC/ACM device and a USB mass storage device. This configuration
|
|
uses apps/system/composite.
|
|
|
|
nsh and nsh2:
|
|
------------
|
|
Configure the NuttShell (nsh) located at examples/nsh.
|
|
|
|
Differences between the two NSH configurations:
|
|
|
|
=========== ======================= ================================
|
|
nsh nsh2
|
|
=========== ======================= ================================
|
|
Platform Windows with Cygwin (2) Windows with Cygwin (2)
|
|
----------- ----------------------- --------------------------------
|
|
Toolchain: NuttX buildroot (1) Codesourcery for Windows (1)
|
|
----------- ----------------------- --------------------------------
|
|
Loader: DfuSe DfuSe
|
|
----------- ----------------------- --------------------------------
|
|
Serial Debug output: USART1 Debug output: USART1
|
|
Console: NSH output: USART1 NSH output: USART1 (3)
|
|
----------- ----------------------- --------------------------------
|
|
I2C No I2C1
|
|
----------- ----------------------- --------------------------------
|
|
microSD Yes Yes
|
|
Support
|
|
----------- ----------------------- --------------------------------
|
|
FAT FS CONFIG_FAT_LCNAMES=y CONFIG_FAT_LCNAMES=y
|
|
Config CONFIG_FAT_LFN=n CONFIG_FAT_LFN=y (4)
|
|
----------- ----------------------- --------------------------------
|
|
Support for No Yes
|
|
Built-in
|
|
Apps
|
|
----------- ----------------------- --------------------------------
|
|
Built-in None apps/examples/nx
|
|
Apps apps/examples/nxhello
|
|
apps/system/usbmsc (5)
|
|
apps/system/i2c
|
|
=========== ======================= ================================
|
|
|
|
(1) You will probably need to modify nsh/setenv.sh or nsh2/setenv.sh
|
|
to set up the correct PATH variable for whichever toolchain you
|
|
may use.
|
|
(2) Since DfuSe is assumed, this configuration may only work under
|
|
Cygwin without modification.
|
|
(3) When any other device other than /dev/console is used for a user
|
|
interface, (1) linefeeds (\n) will not be expanded to carriage return
|
|
/ linefeeds \r\n). You will need to configure your terminal program
|
|
to account for this. And (2) input is not automatically echoed so
|
|
you will have to turn local echo on.
|
|
(4) Microsoft holds several patents related to the design of
|
|
long file names in the FAT file system. Please refer to the
|
|
details in the top-level COPYING file. Please do not use FAT
|
|
long file name unless you are familiar with these patent issues.
|
|
(5) When built as an NSH add-on command (CONFIG_NSH_BUILTIN_APPS=y),
|
|
Caution should be used to assure that the SD drive is not in use when
|
|
the USB storage device is configured. Specifically, the SD driver
|
|
should be unmounted like:
|
|
|
|
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Card is mounted in NSH
|
|
...
|
|
nsh> umount /mnd/sdcard # Unmount before connecting USB!!!
|
|
nsh> msconn # Connect the USB storage device
|
|
...
|
|
nsh> msdis # Disconnect USB storate device
|
|
nsh> mount -t vfat /dev/mmcsd0 /mnt/sdcard # Restore the mount
|
|
|
|
Failure to do this could result in corruption of the SD card format.
|
|
|
|
1. Both configurations use the mconf-based configuration tool. To
|
|
change these configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. The nsh2 contains support for some built-in applications that can be
|
|
enabled by make some additional minor changes:
|
|
|
|
a. examples/can. The CAN test example can be enabled by changing the
|
|
following settings in nsh2/defconfig:
|
|
|
|
CONFIG_CAN=y : Enable CAN "upper-half" driver support
|
|
CONFIG_STM32_CAN1=y : Enable STM32 CAN1 "lower-half" driver support
|
|
|
|
The default CAN settings may need to change in your board board
|
|
configuration:
|
|
|
|
CONFIG_CAN_EXTID=y : Support extended IDs
|
|
CONFIG_CAN1_BAUD=250000 : Bit rate: 250 KHz
|
|
CONFIG_CAN_TSEG1=12 : 80% sample point
|
|
CONFIG_CAN_TSEG2=3
|
|
nx:
|
|
---
|
|
An example using the NuttX graphics system (NX). This example
|
|
focuses on general window controls, movement, mouse and keyboard
|
|
input.
|
|
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
|
|
CONFIG_LCD_RPORTRAIT=y : 240x320 reverse portrait
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. If you configured the multi-used NX server (which is disabled
|
|
by default), then you would also need:
|
|
|
|
CONFIG_EXAMPLES_NX_CLIENTPRIO=80
|
|
CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
|
|
CONFIG_EXAMPLES_NX_SERVERPRIO=120
|
|
CONFIG_EXAMPLES_NX_STACKSIZE=2048
|
|
|
|
3. This example provides a framework for a number of other standalone
|
|
graphics tests.
|
|
|
|
a. apps/examples/nxlines: The NXLINES graphic example illustrates
|
|
drawing of fat lines in various orientations. You can modify
|
|
this configuration so to support the NXLINES example by making
|
|
the following modifications to the NuttX configuration file:
|
|
|
|
Provide the new start-up entry point:
|
|
|
|
CONFIG_USER_ENTRYPOINT="nxlines_main"
|
|
|
|
Disable apps/examples/nx:
|
|
|
|
CONFIG_EXAMPLES_NX=n
|
|
|
|
Enable and configure apps/nxlines/nxlines:
|
|
|
|
CONFIG_EXAMPLES_NXLINES=y
|
|
CONFIG_EXAMPLES_NXLINES_VPLANE=0
|
|
CONFIG_EXAMPLES_NXLINES_DEVNO=0
|
|
CONFIG_EXAMPLES_NXLINES_DEFAULT_COLORS=n
|
|
CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
|
|
CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
|
|
CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
|
|
CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
|
|
CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
|
|
CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
|
|
CONFIG_EXAMPLES_NXLINES_BPP=16
|
|
CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
|
|
|
|
b. apps/examples/nxtext: Another example using the NuttX graphics
|
|
system (NX). This example focuses on placing text on the
|
|
background while pop-up windows occur. Text should continue to
|
|
update normally with or without the popup windows present.
|
|
|
|
You can modify this configuration so to support the NXLINES
|
|
example by making the following modifications to the NuttX
|
|
configuration file:
|
|
|
|
Provide the new start-up entry point:
|
|
|
|
CONFIG_USER_ENTRYPOINT="nxtext_main"
|
|
|
|
Disable apps/examples/nx:
|
|
|
|
CONFIG_EXAMPLES_NX=n
|
|
|
|
Enable an NX font:
|
|
|
|
CONFIG_NXFONT_SERIF22X28B=y
|
|
|
|
Enable and configure apps/nxlines/nxtext:
|
|
|
|
CONFIG_EXAMPLES_NXTEXT=y
|
|
CONFIG_EXAMPLES_NXTEXT_VPLANE=0
|
|
CONFIG_EXAMPLES_NXTEXT_DEVNO=0
|
|
CONFIG_EXAMPLES_NXTEXT_BPP=16
|
|
CONFIG_EXAMPLES_NXTEXT_BMCACHE=512
|
|
CONFIG_EXAMPLES_NXTEXT_GLCACHE=16
|
|
CONFIG_EXAMPLES_NXTEXT_DEFAULT_COLORS=n
|
|
CONFIG_EXAMPLES_NXTEXT_BGCOLOR=0x0011
|
|
CONFIG_EXAMPLES_NXTEXT_BGFONTCOLOR=0xffdf
|
|
CONFIG_EXAMPLES_NXTEXT_PUCOLOR=0xfd20
|
|
CONFIG_EXAMPLES_NXTEXT_PUFONTCOLOR=0x001f
|
|
CONFIG_EXAMPLES_NXTEXT_DEFAULT_FONT=n
|
|
CONFIG_EXAMPLES_NXTEXT_BGFONTID=11
|
|
CONFIG_EXAMPLES_NXTEXT_PUFONTID=1
|
|
CONFIG_EXAMPLES_NXTEXT_EXTERNINIT=n
|
|
|
|
If you configured the multi-used NX server (which is disabled
|
|
by default), then you would also need:
|
|
|
|
CONFIG_EXAMPLES_NXTEXT_STACKSIZE=2048
|
|
CONFIG_EXAMPLES_NXTEXT_CLIENTPRIO=80
|
|
CONFIG_EXAMPLES_NXTEXT_SERVERPRIO=120
|
|
CONFIG_EXAMPLES_NXTEXT_NOTIFYSIGNO=4
|
|
|
|
c. Others could be similar configured: apps/examples/nxhello,
|
|
nximage, ...
|
|
|
|
4. The nsh configuration was used to verify the discrete joystick
|
|
(DJoystick driver). If you would like to duplicate this test, below
|
|
are the configuration changes needed to setup the DJoystick driver
|
|
(see nuttx/drivers/input/djoystick.c) and the DJoystick test (see
|
|
apps/examples/djoystick):
|
|
|
|
Pre-requisites:
|
|
|
|
CONFIG_DISABLE_POLL=n # Don't disable poll()
|
|
CONFIG_BUILTIN=y # Enable support for built-in applications
|
|
CONFIG_NSH_BUILTIN_APPS=y # Enable NSH built-in applications
|
|
|
|
Enable the DJoystick driver:
|
|
|
|
CONFIG_INPUT=y # Enable input driver support
|
|
CONFIG_DJOYSTICK=y # Enable the joystick drivers
|
|
# (default parmeters should be okay)
|
|
Enable the DJoystick Example:
|
|
|
|
CONFIG_EXAMPLES_DJOYSTICK=y # Enable the DJoystick example
|
|
CONFIG_EXAMPLES_DJOYSTICK_DEVNAME="/dev/djoy0"
|
|
CONFIG_EXAMPLES_DJOYSTICK_SIGNO=13
|
|
|
|
When running the configuration, you should see the built-in
|
|
application 'djoy'. Just typo 'djoy' at the NSH command prompt.
|
|
The test will simply should the joystick position and will exect when
|
|
the joystick select indication is received (when the joystick button
|
|
is push downward).
|
|
|
|
nxterm:
|
|
----------
|
|
This is yet another NSH configuration. This NSH configuration differs
|
|
from the other, however, in that it uses the NxTerm driver to host
|
|
the NSH shell.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. Some of the differences in this configuration include these settings
|
|
in the defconfig file:
|
|
|
|
These select NX Multi-User mode:
|
|
|
|
CONFG_NX_MULTIUSER=y
|
|
CONFIG_DISABLE_MQUEUE=n
|
|
|
|
The following definition in the defconfig file to enables the NxTerm
|
|
driver:
|
|
|
|
CONFIG_NXTERM=y
|
|
|
|
And this selects apps/examples/nxterm instead of apps/examples/nsh:
|
|
|
|
CONFIG_EXAMPLES_NXTERM=y
|
|
|
|
Other configuration settings of interest:
|
|
|
|
CONFIG_HOST_WINDOWS=y : Windows
|
|
CONFIG_WINDOWS_CYGWIN=y : with Cygwin
|
|
CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin
|
|
CONFIG_LCD_LANDSCAPE=y : 320x240 landscape
|
|
|
|
pm:
|
|
--
|
|
This is a configuration that is used to test STM32 power management, i.e.,
|
|
to test that the board can go into lower and lower states of power usage
|
|
as a result of inactivity. This configuration is based on the nsh2
|
|
configuration with modifications for testing power management. This
|
|
configuration should provide some guideline for power management in your
|
|
STM32 application.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. Default configuration is Cygwin under windows using the CodeSourcery
|
|
toolchain:
|
|
|
|
CONFIG_HOST_WINDOWS=y : Windows
|
|
CONFIG_WINDOWS_CYGWIN=y : Cygwin
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
|
|
|
|
3. CONFIG_ARCH_CUSTOM_PMINIT and CONFIG_ARCH_IDLE_CUSTOM are necessary
|
|
parts of the PM configuration:
|
|
|
|
CONFIG_ARCH_CUSTOM_PMINIT=y
|
|
|
|
CONFIG_ARCH_CUSTOM_PMINIT moves the PM initialization from
|
|
arch/arm/src/stm32/stm32_pminitialiaze.c to configs/stm3210-eval/src/stm32_pm.c.
|
|
This allows us to support board-specific PM initialization.
|
|
|
|
CONFIG_ARCH_IDLE_CUSTOM=y
|
|
|
|
The bulk of the PM activities occur in the IDLE loop. The IDLE loop
|
|
is special because it is what runs when there is no other task running.
|
|
Therefore when the IDLE executes, we can be assure that nothing else
|
|
is going on; this is the ideal condition for doing reduced power
|
|
management.
|
|
|
|
The configuration CONFIG_ARCH_IDLE_CUSTOM allows us to "steal" the
|
|
normal STM32 IDLE loop (of arch/arm/src/stm32/stm32_idle.c) and replace
|
|
this with our own custom IDLE loop (at configs/stm3210-eval/src/up_idle.c).
|
|
|
|
4. Here are some additional things to note in the configuration:
|
|
|
|
CONFIG_PM_BUTTONS=y
|
|
|
|
CONFIG_PM_BUTTONS enables button support for PM testing. Buttons can
|
|
drive EXTI interrupts and EXTI interrupts can be used to wakeup for
|
|
certain reduced power modes (STOP mode). The use of the buttons here
|
|
is for PM testing purposes only; buttons would normally be part the
|
|
application code and CONFIG_PM_BUTTONS would not be defined.
|
|
|
|
CONFIG_RTC_ALARM=y
|
|
|
|
The RTC alarm is used to wake up from STOP mode and to transition to
|
|
STANDBY mode. This used of the RTC alarm could conflict with other
|
|
uses of the RTC alarm in your application.
|
|
|
|
usbserial:
|
|
---------
|
|
This configuration directory exercises the USB serial class
|
|
driver at examples/usbserial. See examples/README.txt for
|
|
more information.
|
|
|
|
CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin
|
|
|
|
USB debug output can be enabled as by changing the following
|
|
settings in the configuration file:
|
|
|
|
-CONFIG_DEBUG_FEATURES=n
|
|
-CONFIG_DEBUG_INFO=n
|
|
-CONFIG_DEBUG_USB=n
|
|
+CONFIG_DEBUG_FEATURES=y
|
|
+CONFIG_DEBUG_INFO=y
|
|
+CONFIG_DEBUG_USB=y
|
|
|
|
-CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
|
|
-CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
|
|
-CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
|
|
-CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
|
|
-CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
|
|
+CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=y
|
|
+CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=y
|
|
+CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=y
|
|
+CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=y
|
|
+CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=y
|
|
|
|
By default, the usbserial example uses the Prolific PL2303
|
|
serial/USB converter emulation. The example can be modified
|
|
to use the CDC/ACM serial class by making the following changes
|
|
to the configuration file:
|
|
|
|
-CONFIG_PL2303=y
|
|
+CONFIG_PL2303=n
|
|
|
|
-CONFIG_CDCACM=n
|
|
+CONFIG_CDCACM=y
|
|
|
|
The example can also be converted to use the alternative
|
|
USB serial example at apps/examples/usbterm by changing the
|
|
following:
|
|
|
|
-CONFIG_EXAMPLES_USBSERIAL=y
|
|
+CONFIG_EXAMPLES_USBSERIAL=n
|
|
|
|
-CONFIG_EXAMPLES_USBTERM=n
|
|
+CONFIG_EXAMPLES_USBTERM=y
|
|
|
|
usbmsc:
|
|
-------
|
|
This configuration directory exercises the USB mass storage
|
|
class driver at system/usbmsc. See examples/README.txt for
|
|
more information.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. Build environment (can be easily reconfigured):
|
|
|
|
CONFIG_HOST_LINUX=y : Linux (or Cygwin)
|
|
CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin
|