142 lines
5.4 KiB
C
142 lines
5.4 KiB
C
/****************************************************************************
|
|
* boards/arm/sam34/sam4l-xplained/src/sam_autoleds.c
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/* There are three LEDs on board the SAM4L Xplained Pro board: The EDBG
|
|
* controls two of the LEDs, a power LED and a status LED. There is only
|
|
* one user controllable LED, a yellow LED labeled LED0 near the SAM4L USB
|
|
* connector.
|
|
*
|
|
* This LED is controlled by PC07 and LED0 can be activated by driving the
|
|
* PC07 to GND.
|
|
*
|
|
* When CONFIG_ARCH_LEDS is defined in the NuttX configuration, NuttX will
|
|
* control LED0 as follows:
|
|
*
|
|
* SYMBOL Meaning LED0
|
|
* ------------------- ----------------------- ------
|
|
* LED_STARTED NuttX has been started OFF
|
|
* LED_HEAPALLOCATE Heap has been allocated OFF
|
|
* LED_IRQSENABLED Interrupts enabled OFF
|
|
* LED_STACKCREATED Idle stack created ON
|
|
* LED_INIRQ In an interrupt** N/C
|
|
* LED_SIGNAL In a signal handler*** N/C
|
|
* LED_ASSERTION An assertion failed N/C
|
|
* LED_PANIC The system has crashed FLASH
|
|
*
|
|
* Thus is LED0 is statically on, NuttX has successfully booted and is,
|
|
* apparently, running normally. If LED0 is flashing at approximately
|
|
* 2Hz, then a fatal error has been detected and the system has halted.
|
|
*/
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
#include <assert.h>
|
|
#include <debug.h>
|
|
|
|
#include <nuttx/board.h>
|
|
#include <arch/board/board.h>
|
|
|
|
#include "sam_gpio.h"
|
|
#include "sam4l-xplained.h"
|
|
|
|
#ifdef CONFIG_ARCH_LEDS
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: board_autoled_initialize
|
|
****************************************************************************/
|
|
|
|
void board_autoled_initialize(void)
|
|
{
|
|
sam_configgpio(GPIO_LED0);
|
|
}
|
|
|
|
/****************************************************************************
|
|
* Name: board_autoled_on
|
|
****************************************************************************/
|
|
|
|
void board_autoled_on(int led)
|
|
{
|
|
bool ledstate = true;
|
|
|
|
switch (led)
|
|
{
|
|
case 0: /* LED_STARTED: NuttX has been started LED0=OFF */
|
|
/* LED_HEAPALLOCATE: Heap has been allocated LED0=OFF */
|
|
/* LED_IRQSENABLED: Interrupts enabled LED0=OFF */
|
|
break; /* Leave ledstate == true to turn OFF */
|
|
|
|
default:
|
|
case 2: /* LED_INIRQ: In an interrupt LED0=N/C */
|
|
/* LED_SIGNAL: In a signal handler LED0=N/C */
|
|
/* LED_ASSERTION: An assertion failed LED0=N/C */
|
|
return; /* Return to leave LED0 unchanged */
|
|
|
|
case 3: /* LED_PANIC: The system has crashed LED0=FLASH */
|
|
case 1: /* LED_STACKCREATED: Idle stack created LED0=ON */
|
|
ledstate = false; /* Set ledstate == false to turn ON */
|
|
break;
|
|
}
|
|
|
|
sam_gpiowrite(GPIO_LED0, ledstate);
|
|
}
|
|
|
|
/****************************************************************************
|
|
* Name: board_autoled_off
|
|
****************************************************************************/
|
|
|
|
void board_autoled_off(int led)
|
|
{
|
|
switch (led)
|
|
{
|
|
/* These should not happen and are ignored */
|
|
|
|
default:
|
|
case 0: /* LED_STARTED: NuttX has been started LED0=OFF */
|
|
/* LED_HEAPALLOCATE: Heap has been allocated LED0=OFF */
|
|
/* LED_IRQSENABLED: Interrupts enabled LED0=OFF */
|
|
case 1: /* LED_STACKCREATED: Idle stack created LED0=ON */
|
|
|
|
/* These result in no-change */
|
|
|
|
case 2: /* LED_INIRQ: In an interrupt LED0=N/C */
|
|
/* LED_SIGNAL: In a signal handler LED0=N/C */
|
|
/* LED_ASSERTION: An assertion failed LED0=N/C */
|
|
return; /* Return to leave LED0 unchanged */
|
|
|
|
/* Turn LED0 off set driving the output high */
|
|
|
|
case 3: /* LED_PANIC: The system has crashed LED0=FLASH */
|
|
sam_gpiowrite(GPIO_LED0, true);
|
|
break;
|
|
}
|
|
}
|
|
|
|
#endif /* CONFIG_ARCH_LEDS */
|