33041c5d08
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@2972 42af7a65-404d-4744-a932-0658087f49c3
189 lines
6.0 KiB
Plaintext
Executable File
189 lines
6.0 KiB
Plaintext
Executable File
README
|
|
^^^^^^
|
|
|
|
This is the README file for the NuttX port to the Atmel AVR32DEV1 board.
|
|
|
|
Contents
|
|
^^^^^^^^
|
|
|
|
* Toolchains
|
|
* Development Environment
|
|
* GNU Toolchains
|
|
* IDEs
|
|
* AVR32 Bootloader
|
|
* AVR32DEV1 Configuration Options
|
|
* Configurations
|
|
|
|
Development Environment
|
|
^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Either Linux or Cygwin on Windows can be used for the development environment.
|
|
The source has been built only using the GNU toolchain (see below). Other
|
|
toolchains will likely cause problems. Testing was performed using the Cygwin
|
|
environment.
|
|
|
|
GNU Toolchains
|
|
^^^^^^^^^^^^^^
|
|
|
|
The build logic in these directories assume that you are using the GNU
|
|
toolchain with the Atmel patches. The patch file, pre-patched tool sources,
|
|
and pre-built binaries are available from the Atmel website.
|
|
|
|
CONFIG_AVR32_AVRTOOLSW=y # Use the windows version
|
|
CONFIG_AVR32_AVRTOOLSL=y # Ue the Linux version
|
|
|
|
NOTE: The NuttX builtroot cannot be used to build the AVR32 toolchain.
|
|
This is because the Atmel patches that add support for the AVR32 are not
|
|
included in the NuttX buildroot.
|
|
|
|
IDEs
|
|
^^^^
|
|
|
|
NuttX is built using command-line make. It can be used with an IDE, but some
|
|
effort will be required to create the project.
|
|
|
|
Makefile Build
|
|
--------------
|
|
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
|
simply use the NuttX makefile to build the system. That is almost for free
|
|
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
|
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
|
there is a lot of help on the internet).
|
|
|
|
Native Build
|
|
------------
|
|
Here are a few tips before you start that effort:
|
|
|
|
1) Select the toolchain that you will be using in your .config file
|
|
2) Start the NuttX build at least one time from the Cygwin command line
|
|
before trying to create your project. This is necessary to create
|
|
certain auto-generated files and directories that will be needed.
|
|
3) Set up include pathes: You will need include/, arch/avr/src/at91uc3,
|
|
arch/avr/src/common, arch/arm/src/avr, and sched/.
|
|
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
|
on the command line.
|
|
|
|
Startup files will probably cause you some headaches. The NuttX startup file
|
|
is arch/avr/src/avr3/up_nommuhead.S.
|
|
|
|
AVR32 Bootloader
|
|
^^^^^^^^^^^^^^^^
|
|
|
|
The linker scripts (ld.script) assume that you are using the bootloader.
|
|
The bootloader resides at 0x8000:0000 and so the ld.script files link
|
|
the application to execute after the bootloader at 0x8000:2000. To link
|
|
so that NuttX boots directly without using the bootloader, change the
|
|
flash definition from:
|
|
|
|
flash (rxai!w) : ORIGIN = 0x80002000, LENGTH = 256K - 8K
|
|
|
|
to:
|
|
flash (rxai!w) : ORIGIN = 0x80000000, LENGTH = 256K
|
|
|
|
AVR32DEV1 Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=avr
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_AVR=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_AVR32=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=at91uc3
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_AT91UC3B0256
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=avr32dev1 (for the AV32DEV1 board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_AVR32DEV1
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_START=0x20000000
|
|
|
|
CONFIG_DRAM_END - Last address+1 of installed RAM
|
|
|
|
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
|
|
|
CONFIG_ARCH_IRQPRIO - The AT91UC3B0256 supports interrupt prioritization
|
|
|
|
CONFIG_ARCH_IRQPRIO=y
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
AT91UC3B0256 specific device driver settings
|
|
|
|
CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
|
|
console and ttys0 (default is the USART0).
|
|
CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_USARTn_BAUD - The configure BAUD of the USART. Must be
|
|
CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_USARTn_2STOP - Two stop bits
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each Stellaris LM3S6965 Evaluation Kit configuration is maintained in a
|
|
sudirectory and can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh avr32dev1/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest:
|
|
This configuration directory, performs a simple OS test using
|
|
examples/ostest.
|
|
|
|
|