204 lines
6.8 KiB
C
204 lines
6.8 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32f0l0g0/nucleo-l073rz/include/board.h
|
|
* include/arch/board/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32F0L0G0_NUCLEO_L073RZ_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_STM32F0L0G0_NUCLEO_L073RZ_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
# include <stdbool.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* HSI - Internal 8 MHz RC Oscillator
|
|
* LSI - 32 KHz RC
|
|
* HSE - 8 MHz from MCO output of ST-LINK
|
|
* LSE - 32.768 kHz
|
|
*/
|
|
|
|
#define STM32_BOARD_XTAL 8000000ul
|
|
|
|
#define STM32_HSEBYP_ENABLE
|
|
#define STM32_HSI_FREQUENCY 8000000ul
|
|
#define STM32_LSI_FREQUENCY 32000 /* Between 30kHz and 60kHz */
|
|
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
|
|
#define STM32_LSE_FREQUENCY 32768 /* X2 on board */
|
|
|
|
/* PLL source is HSE/1, PLL multipler is 8:
|
|
* PLL frequency is 8MHz (XTAL) x 8 = 64MHz
|
|
*/
|
|
|
|
#define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC
|
|
#define STM32_CFGR_PLLXTPRE 0
|
|
#define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx8
|
|
#define STM32_PLL_FREQUENCY (8*STM32_BOARD_XTAL)
|
|
|
|
/* Use the PLL and set the SYSCLK source to be the PLL/2 (32MHz) */
|
|
|
|
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL
|
|
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
|
|
#define STM32_CFGR_PLLDIV RCC_CFGR_PLLDIV_2
|
|
#define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY/2
|
|
|
|
/* AHB clock (HCLK) is SYSCLK (32MHz) */
|
|
|
|
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
|
|
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
|
|
#define STM32_BOARD_HCLK STM32_HCLK_FREQUENCY
|
|
|
|
/* APB2 clock (PCLK2) is HCLK (32MHz) */
|
|
|
|
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
|
|
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
|
|
#define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY)
|
|
|
|
/* APB1 clock (PCLK1) is HCLK/2 (16MHz) */
|
|
|
|
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLKd2
|
|
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY/2)
|
|
|
|
/* 48MHz clock configuration */
|
|
|
|
#if defined(CONFIG_STM32F0L0G0_USB) || defined(CONFIG_STM32F0L0G0_RNG)
|
|
# define STM32_USE_CLK48 1
|
|
# define STM32_CLK48_SEL RCC_CCIPR_CLK48SEL_HSI48
|
|
# define STM32_HSI48_SYNCSRC SYNCSRC_NONE
|
|
#endif
|
|
|
|
/* TODO: timers */
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* The Nucleo LO73RZ board has three LEDs. Two of these are controlled by
|
|
* logic on the board and are not available for software control:
|
|
*
|
|
* LD1 COM: LD1 default status is red. LD1 turns to green to indicate that
|
|
* communications are in progress between the PC and the
|
|
* ST-LINK/V2-1.
|
|
* LD3 PWR: red LED indicates that the board is powered.
|
|
*
|
|
* And one can be controlled by software:
|
|
*
|
|
* User LD2: green LED is a user LED connected to the I/O PA5 of the
|
|
* STM32LO73RZ.
|
|
*
|
|
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LED in
|
|
* any way. The following definition is used to access the LED.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0 /* User LD2 */
|
|
#define BOARD_NLEDS 1
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
|
|
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the LED on board
|
|
* the Nucleo LO73RZ. The following definitions describe how NuttX controls
|
|
* the LED:
|
|
*
|
|
* SYMBOL Meaning LED1 state
|
|
* ------------------ ----------------------- ----------
|
|
* LED_STARTED NuttX has been started OFF
|
|
* LED_HEAPALLOCATE Heap has been allocated OFF
|
|
* LED_IRQSENABLED Interrupts enabled OFF
|
|
* LED_STACKCREATED Idle stack created ON
|
|
* LED_INIRQ In an interrupt No change
|
|
* LED_SIGNAL In a signal handler No change
|
|
* LED_ASSERTION An assertion failed No change
|
|
* LED_PANIC The system has crashed Blinking
|
|
* LED_IDLE STM32 is is sleep mode Not used
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 0
|
|
#define LED_IRQSENABLED 0
|
|
#define LED_STACKCREATED 1
|
|
#define LED_INIRQ 2
|
|
#define LED_SIGNAL 2
|
|
#define LED_ASSERTION 2
|
|
#define LED_PANIC 1
|
|
|
|
/* Button definitions *******************************************************/
|
|
|
|
/* The Nucleo LO73RZ supports two buttons; only one button is controllable
|
|
* by software:
|
|
*
|
|
* B1 USER: user button connected to the I/O PC13 of the STM32LO73RZ.
|
|
* B2 RESET: push button connected to NRST is used to RESET the
|
|
* STM32LO73RZ.
|
|
*/
|
|
|
|
#define BUTTON_USER 0
|
|
#define NUM_BUTTONS 1
|
|
|
|
#define BUTTON_USER_BIT (1 << BUTTON_USER)
|
|
|
|
/* Alternate function pin selections ****************************************/
|
|
|
|
/* I2C */
|
|
|
|
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_2 /* D15 - PB8 */
|
|
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_2 /* D14 - PB9 */
|
|
|
|
/* SPI1 */
|
|
|
|
#define GPIO_SPI1_MISO GPIO_SPI1_MISO_2 /* D12 - PA6 */
|
|
#define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_2 /* D11 - PA7 */
|
|
#define GPIO_SPI1_SCK GPIO_SPI1_SCK_1 /* D13 - PA5 */
|
|
|
|
/* SPI2 */
|
|
|
|
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_1 /* PB14 */
|
|
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */
|
|
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_1 /* PB10 */
|
|
|
|
/* USART */
|
|
|
|
/* By default the USART2 is connected to STLINK Virtual COM Port:
|
|
* USART2_RX - PA3
|
|
* USART2_TX - PA2
|
|
*/
|
|
|
|
#define GPIO_USART2_RX GPIO_USART2_RX_1 /* PA3 */
|
|
#define GPIO_USART2_TX GPIO_USART2_TX_1 /* PA2 */
|
|
|
|
/* DMA channels *************************************************************/
|
|
|
|
/* ADC */
|
|
|
|
#define ADC1_DMA_CHAN DMACHAN_ADC1 /* DMA1_CH1 */
|
|
|
|
#endif /* __BOARDS_ARM_STM32F0L0G0_NUCLEO_LO73RZ_INCLUDE_BOARD_H */
|