9bb950da29
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5322 42af7a65-404d-4744-a932-0658087f49c3
331 lines
8.4 KiB
Plaintext
331 lines
8.4 KiB
Plaintext
#
|
|
# For a description of the syntax of this configuration file,
|
|
# see misc/tools/kconfig-language.txt.
|
|
#
|
|
|
|
config LCD_NOGETRUN
|
|
bool "Write-only LCD"
|
|
default n
|
|
---help---
|
|
Many LCD hardware interfaces provide only minimal graphics capability. In
|
|
particulary, many simple LCD interfaces are write only. That is we, can
|
|
write graphics data to the LCD device memory, but we cannot read it back.
|
|
If the LCD hardware does not support reading the graphics memory, then
|
|
this option should be defined so that the NX layer can taking alternative
|
|
measures when the LCD is not readable. For example, if the LCD is not
|
|
readable, then NX will not attempt to support transparency.
|
|
|
|
See also NX_WRITEONLY in the graphics support menu.
|
|
|
|
config LCD_MAXCONTRAST
|
|
int "LCD maximum contrast"
|
|
default 63 if NOKIA6100_S1D15G10
|
|
default 127 if NOKIA6100_PCF8833
|
|
default 255 if LCD_P14201
|
|
default 63
|
|
---help---
|
|
must be 63 with the Epson controller and 127 with
|
|
the Phillips controller.
|
|
|
|
config LCD_MAXPOWER
|
|
int "LCD maximum power"
|
|
default 1
|
|
---help---
|
|
Maximum value of backlight setting. The backlight
|
|
control is managed outside of the 6100 driver so this value has no
|
|
meaning to the driver. Board-specific logic may place restrictions on
|
|
this value.
|
|
|
|
config LCD_P14201
|
|
bool "Rit P1402 series display"
|
|
default n
|
|
---help---
|
|
p14201.c. Driver for RiT P14201 series display with SD1329 IC
|
|
controller. This OLED is used with older versions of the
|
|
TI/Luminary LM3S8962 Evaluation Kit.
|
|
|
|
if LCD_P14201
|
|
config P14201_NINTERFACES
|
|
int "Number of physical P14201 devices"
|
|
default 1
|
|
range 1,1
|
|
---help---
|
|
Specifies the number of physical P14201
|
|
devices that will be supported.
|
|
|
|
config P14201_SPIMODE
|
|
int "SPI mode"
|
|
default 2
|
|
range 0,3
|
|
---help---
|
|
Controls the SPI mode
|
|
|
|
config P14201_FREQUENCY
|
|
int "SPI frequency"
|
|
default 1000000
|
|
---help---
|
|
Define to use a different bus frequency,FIXME DEFAULT VALUE OK?
|
|
|
|
config P14201_FRAMEBUFFER
|
|
bool "Enable P14201 GDDRAM cache"
|
|
default y
|
|
---help---
|
|
If defined, accesses will be performed
|
|
using an in-memory copy of the OLEDs GDDRAM. This cost of this
|
|
buffer is 128 * 96 / 2 = 6Kb. If this is defined, then the driver
|
|
will be fully functional. If not, then it will have the following
|
|
limitations:
|
|
|
|
Reading graphics memory cannot be supported, and
|
|
|
|
All pixel writes must be aligned to byte boundaries.
|
|
The latter limitation effectively reduces the 128x96 disply to 64x96.
|
|
endif
|
|
|
|
config LCD_NOKIA6100
|
|
bool "Nokia 6100 display support"
|
|
default n
|
|
---help---
|
|
nokia6100.c. Supports the Nokia 6100 display with either the Philips
|
|
PCF883 or the Epson S1D15G10 display controller. This LCD is used
|
|
with the Olimex LPC1766-STK (but has not been fully integrated).
|
|
if LCD_NOKIA6100
|
|
config NOKIA6100_NINTERFACES
|
|
int "Number of physical NOKIA6100 devices"
|
|
default 1
|
|
range 1,1
|
|
---help---
|
|
Specifies the number of physical Nokia
|
|
6100 devices that will be supported.
|
|
|
|
choice NOKIA6100_CONTROLLER
|
|
prompt "Controller Setup"
|
|
default NOKIA6100_S1D15G10
|
|
config NOKIA6100_S1D15G10
|
|
bool "S1D15G10 controller"
|
|
---help---
|
|
Selects the Epson S1D15G10 display controller
|
|
|
|
config NOKIA6100_PCF8833
|
|
bool "PCF8833 controller"
|
|
---help---
|
|
Selects the Phillips PCF8833 display controller
|
|
endchoice
|
|
|
|
config NOKIA6100_SPIMODE
|
|
int "SPI mode"
|
|
default 0
|
|
range 0,3
|
|
---help---
|
|
Controls the SPI mode
|
|
|
|
config NOKIA6100_FREQUENCY
|
|
int "SPI frequency"
|
|
default 1000000
|
|
---help---
|
|
Define to use a different bus frequency
|
|
|
|
config NOKIA6100_BLINIT
|
|
bool "Back light initial"
|
|
default n
|
|
---help---
|
|
Initial backlight setting
|
|
The following may need to be tuned for your hardware:
|
|
|
|
config NOKIA6100_BPP
|
|
int "Display bits per pixel"
|
|
default 8
|
|
---help---
|
|
Device supports 8, 12, and 16 bits per pixel.
|
|
|
|
config NOKIA6100_INVERT
|
|
int "Display inversion"
|
|
default 1
|
|
range 0,1
|
|
---help---
|
|
Display inversion, 0 or 1, Default: 1
|
|
|
|
config NOKIA6100_MY
|
|
int "Display row direction"
|
|
default 0
|
|
range 0,1
|
|
---help---
|
|
Display row direction, 0 or 1, Default: 0
|
|
|
|
config NOKIA6100_MX
|
|
int "Display column direction"
|
|
default 1
|
|
range 0,1
|
|
---help---
|
|
Display column direction, 0 or 1, Default: 1
|
|
|
|
config NOKIA6100_V
|
|
int "Display address direction"
|
|
default 0
|
|
range 0,1
|
|
---help---
|
|
Display address direction, 0 or 1, Default: 0
|
|
|
|
config NOKIA6100_ML
|
|
int "Display scan direction"
|
|
default 0
|
|
range 0,1
|
|
---help---
|
|
Display scan direction, 0 or 1, Default: 0
|
|
|
|
config NOKIA6100_RGBORD
|
|
int "Display RGB order"
|
|
default 0
|
|
range 0,1
|
|
---help---
|
|
Display RGB order, 0 or 1, Default: 0
|
|
Required LCD driver settings:
|
|
endif
|
|
|
|
config LCD_UG9664HSWAG01
|
|
bool "UG-9664HSWAG01 OLED Display Module"
|
|
default n
|
|
---help---
|
|
OLED Display Module, UG-9664HSWAG01, Univision Technology Inc. Used
|
|
with the LPCXpresso and Embedded Artists base board.
|
|
|
|
Required LCD driver settings:
|
|
LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
|
|
LCD_MAXPOWER should be 1: 0=off, 1=on
|
|
|
|
Required SPI driver settings:
|
|
SPI_CMDDATA - Include support for cmd/data selection.
|
|
|
|
if LCD_UG9664HSWAG01
|
|
|
|
config UG9664HSWAG01_SPIMODE
|
|
int "UG-9664HSWAG01 SPI Mode"
|
|
default 0
|
|
---help---
|
|
Controls the SPI mode
|
|
|
|
config UG9664HSWAG01_FREQUENCY
|
|
int "UG-9664HSWAG01 SPI Frequency"
|
|
default 3500000
|
|
---help---
|
|
Define to use a different bus frequency
|
|
|
|
config UG9664HSWAG01_NINTERFACES
|
|
int "Number of UG-9664HSWAG01 Devices"
|
|
default 1
|
|
---help---
|
|
Specifies the number of physical UG-9664HSWAG01 devices that will be
|
|
supported. NOTE: At present, this must be undefined or defined to be 1.
|
|
|
|
config UG9664HSWAG01_POWER
|
|
bool "Power control"
|
|
default n
|
|
---help---
|
|
If the hardware supports a controllable OLED a power supply, this
|
|
configuration should be defined. In this case the system must
|
|
provide an interface ug_power().
|
|
|
|
endif
|
|
|
|
config LCD_UG2864AMBAG01
|
|
bool "UG-2864AMBAG01 OLED Display Module"
|
|
default n
|
|
---help---
|
|
OLED Display Module, UG-2864AMBAG01, Univision Technology Inc.
|
|
|
|
Required LCD driver settings:
|
|
LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
|
|
LCD_MAXPOWER should be 1: 0=off, 1=on
|
|
|
|
Required SPI driver settings:
|
|
SPI_CMDDATA - Include support for cmd/data selection.
|
|
|
|
if LCD_UG2864AMBAG01
|
|
|
|
config UG2864AMBAG01_SPIMODE
|
|
int "UG-2864AMBAG01 SPI Mode"
|
|
default 3
|
|
---help---
|
|
Controls the SPI mode
|
|
|
|
config UG2864AMBAG01_FREQUENCY
|
|
int "UG-2864AMBAG01 SPI Frequency"
|
|
default 3500000
|
|
---help---
|
|
Define to use a different bus frequency
|
|
|
|
config UG2864AMBAG01_NINTERFACES
|
|
int "Number of UG-2864AMBAG01 Devices"
|
|
default 1
|
|
---help---
|
|
Specifies the number of physical UG-9664HSWAG01 devices that will be
|
|
supported. NOTE: At present, this must be undefined or defined to be 1.
|
|
|
|
endif
|
|
|
|
config LCD_SSD1289
|
|
bool "LCD Based on SSD1289 Controller"
|
|
default n
|
|
---help---
|
|
Enables generic support for any LCD based on the Solomon Systech,
|
|
Ltd, SSD1289 Controller. Use of this driver will usually require so
|
|
detailed customization of the LCD initialization code as necessary
|
|
for the specific LCD driven by the SSD1289 controller.
|
|
|
|
if LCD_SSD1289
|
|
|
|
choice
|
|
prompt "SSD1289 Initialization Profile"
|
|
default SSD1289_PROFILE1
|
|
|
|
config SSD1289_PROFILE1
|
|
bool "Profile 1"
|
|
|
|
config SSD1289_PROFILE2
|
|
bool "Profile 2"
|
|
|
|
config SSD1289_PROFILE3
|
|
bool "Profile 3"
|
|
|
|
endchoice
|
|
endif
|
|
|
|
choice
|
|
prompt "LCD Orientation"
|
|
default LCD_LANDSCAPE
|
|
depends on LCD
|
|
---help---
|
|
Some LCD drivers may support displays in different orientations.
|
|
If the LCD driver supports this capability, than these are configuration
|
|
options to select that display orientation.
|
|
|
|
config LCD_LANDSCAPE
|
|
bool "Landscape orientation"
|
|
---help---
|
|
Define for "landscape" orientation support. Landscape mode refers one
|
|
of two orientations where the the display is wider than it is tall
|
|
(LCD_RLANDSCAPE is the other). This is the default orientation.
|
|
|
|
config LCD_PORTRAIT
|
|
bool "Portrait orientation"
|
|
---help---
|
|
Define for "portrait" orientation support. Portrait mode refers one
|
|
of two orientations where the the display is taller than it is wide
|
|
(LCD_RPORTAIT is the other).
|
|
|
|
config LCD_RPORTRAIT
|
|
bool "Reverse portrait display"
|
|
---help---
|
|
Define for "reverse portrait" orientation support. Reverse portrait mode
|
|
refers one of two orientations where the the display is taller than it is
|
|
wide (LCD_PORTAIT is the other).
|
|
|
|
config LCD_RLANDSCAPE
|
|
bool "Reverse landscape orientation"
|
|
---help---
|
|
Define for "reverse landscape" orientation support. Reverse landscape mode
|
|
refers one of two orientations where the the display is wider than it is
|
|
tall (LCD_LANDSCAPE is the other).
|
|
|
|
endchoice
|