310 lines
11 KiB
Plaintext
310 lines
11 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
README for NuttX port to the Stellaris LMS38962 Evaluation Kit
|
|
|
|
Contents
|
|
^^^^^^^^
|
|
|
|
Stellaris LMS38962 Evaluation Kit
|
|
OLED
|
|
USB Device Controller Functions
|
|
Stellaris LM3S8962 Evaluation Kit Configuration Options
|
|
Configurations
|
|
|
|
Stellaris LMS38962 Evaluation Kit
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
The Stellaris LM3S8962 Evaluation Board includes the following features:
|
|
|
|
o Stellaris LM3S8962 microcontroller with fully-integrated 10/100 embedded
|
|
Ethernet controller
|
|
o Simple setup; USB cable provides serial communication, debugging, and
|
|
power
|
|
o OLED graphics display with 128 x 96 pixel resolution
|
|
o User LED, navigation switches, and select pushbuttons
|
|
o Magnetic speaker
|
|
o LM3S8962 I/O available on labeled break-out pads
|
|
o Standard ARM® 20-pin JTAG debug connector with input and output modes
|
|
o USB interface for debugging and power supply
|
|
o MicroSD card slot
|
|
|
|
Features of the LM3S8962 Microcontroller
|
|
|
|
o 32-bit RISC performance using ARM® Cortex™-M3 v7M architecture
|
|
- 50-MHz operation
|
|
- Hardware-division and single-cycle-multiplication
|
|
- Integrated Nested Vectored Interrupt Controller (NVIC)
|
|
- 42 interrupt channels with eight priority levels
|
|
o 256 KB single-cycle flash
|
|
o 64 KB single-cycle SRAM
|
|
o Four general-purpose 32-bit timers
|
|
o Integrated Ethernet MAC and PHY
|
|
o Three fully programmable 16C550-type UARTs
|
|
o Four 10-bit channels (inputs) when used as single-ended inputs
|
|
o Two independent integrated analog comparators
|
|
o Two I2C modules
|
|
o Three PWM generator blocks
|
|
- One 16-bit counter
|
|
- Two comparators
|
|
- Produces two independent PWM signals
|
|
- One dead-band generator
|
|
o Two QEI modules with position integrator for tracking encoder position
|
|
o 0 to 42 GPIOs, depending on user configuration
|
|
o On-chip low drop-out (LDO) voltage regulator
|
|
|
|
GPIO Usage
|
|
|
|
PIN SIGNAL EVB Function
|
|
--- ----------- ---------------------------------------
|
|
26 PA0/U0RX Virtual COM port receive
|
|
27 PA1/U0TX Virtual COM port transmit
|
|
10 PD0/IDX0 SD card chip select
|
|
11 PD1/PWM1 Sound
|
|
30 PA4/SSI0RX SD card data out
|
|
31 PA5/SSI0TX SD card and OLED display data in
|
|
28 PA2/SSI0CLK SD card and OLED display clock
|
|
22 PC7/PHB0 OLED display data/control select
|
|
29 PA3/SSI0FSS OLED display chip select
|
|
73 PE1/PWM5 Down switch
|
|
74 PE2/PHB1 Left switch
|
|
72 PE0/PWM4 Up switch
|
|
75 PE3/PHA1 Right switch
|
|
61 PF1/IDX1 Select switch
|
|
47 PF0/PWM0 User LED
|
|
23 PC6/CCP3 Enable +15 V
|
|
|
|
OLED
|
|
^^^^
|
|
|
|
The Evaluation Kit includes an OLED graphics display. Features:
|
|
|
|
- RiT P14201 series display
|
|
- 128 columns by 96 rows
|
|
- 4-bit, 16-level gray scale.
|
|
- High-contrast (typ. 500:1)
|
|
- Excellent brightness (120 cd/m2)
|
|
- Fast 10 us response.
|
|
|
|
The OLED display has a built-in controller IC with synchronous serial and
|
|
parallel interfaces (SSD1329). Synchronous serial (SSI) is used on the EVB.
|
|
The SSI port is shared with the microSD card slot.
|
|
|
|
- PC7: OLED display data/control select (D/Cn)
|
|
- PA3: OLED display chip select (CSn)
|
|
|
|
NOTE: Newer versions of the LM3S8962 Evaluation Kit has an OSAM 128x64x4 OLED
|
|
display. Some tweaks to drivers/lcd/p14201.c would be required to support that
|
|
LCD.
|
|
|
|
USB Device Controller Functions
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
Device Overview
|
|
|
|
An FT2232 device from Future Technology Devices International Ltd manages
|
|
USB-to-serial conversion. The FT2232 is factory configured by Luminary
|
|
Micro to implement a JTAG/SWD port (synchronous serial) on channel A and
|
|
a Virtual COM Port (VCP) on channel B. This feature allows two simultaneous
|
|
communications links between the host computer and the target device using
|
|
a single USB cable. Separate Windows drivers for each function are provided
|
|
on the Documentation and Software CD.
|
|
|
|
Debugging with JTAG/SWD
|
|
|
|
The FT2232 USB device performs JTAG/SWD serial operations under the control
|
|
of the debugger or the Luminary Flash Programmer. It also operate as an
|
|
In-Circuit Debugger Interface (ICDI), allowing debugging of any external
|
|
target board. Debugging modes:
|
|
|
|
MODE DEBUG FUNCTION USE SELECTED BY
|
|
1 Internal ICDI Debug on-board LM3S8962 Default Mode
|
|
microcontroller over USB
|
|
interface.
|
|
2 ICDI out to JTAG/SWD The EVB is used as a USB Connecting to an external
|
|
header to SWD/JTAG interface to target and starting debug
|
|
an external target. software. The red Debug Out
|
|
LED will be ON.
|
|
3 In from JTAG/SWD For users who prefer an Connecting an external
|
|
header external debug interface debugger to the JTAG/SWD
|
|
(ULINK, JLINK, etc.) with header.
|
|
the EVB.
|
|
|
|
Virtual COM Port
|
|
|
|
The Virtual COM Port (VCP) allows Windows applications (such as HyperTerminal)
|
|
to communicate with UART0 on the LM3S8962 over USB. Once the FT2232 VCP
|
|
driver is installed, Windows assigns a COM port number to the VCP channel.
|
|
|
|
Stellaris LM3S8962 Evaluation Kit Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_CORTEXM3=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=lm
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
|
chip:
|
|
|
|
CONFIG_ARCH_CHIP_LM3S8962
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the boards/ subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=lm3s8962-ek (for the Stellaris LM3S8962 Evaluation Kit)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_LM3S8962EK
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
|
|
|
CONFIG_RAM_SIZE=0x00010000 (64Kb)
|
|
|
|
CONFIG_RAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_RAM_START=0x20000000
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
|
|
|
There are configurations for disabling support for interrupts GPIO ports.
|
|
GPIOJ must be disabled because it does not exist on the LM3S8962.
|
|
Additional interrupt support can be disabled if desired to reduce memory
|
|
footprint.
|
|
|
|
CONFIG_TIVA_GPIOA_IRQS=y
|
|
CONFIG_TIVA_GPIOB_IRQS=y
|
|
CONFIG_TIVA_GPIOC_IRQS=y
|
|
CONFIG_TIVA_GPIOD_IRQS=y
|
|
CONFIG_TIVA_GPIOE_IRQS=y
|
|
CONFIG_TIVA_GPIOF_IRQS=y
|
|
CONFIG_TIVA_GPIOG_IRQS=y
|
|
CONFIG_TIVA_GPIOH_IRQS=y
|
|
CONFIG_TIVA_GPIOJ_IRQS=n << Always
|
|
|
|
LM3S8962 specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
CONFIG_TIVA_SSI0 - Select to enable support for SSI0
|
|
CONFIG_TIVA_SSI1 - Select to enable support for SSI1
|
|
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
|
Poll-waiting is recommended if the interrupt rate would be to
|
|
high in the interrupt driven case.
|
|
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
|
emptying the Rx FIFO. If the SPI frequency is high and this
|
|
value is large, then larger values of this setting may cause
|
|
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
|
|
|
CONFIG_TIVA_ETHERNET - This must be set (along with CONFIG_NET)
|
|
to build the Stellaris Ethernet driver
|
|
CONFIG_TIVA_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
|
CONFIG_TIVA_BOARDMAC - If the board-specific logic can provide
|
|
a MAC address (via tiva_ethernetmac()), then this should be selected.
|
|
CONFIG_TIVA_ETHHDUPLEX - Set to force half duplex operation
|
|
CONFIG_TIVA_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
|
CONFIG_TIVA_ETHNOPAD - Set to suppress Tx padding
|
|
CONFIG_TIVA_MULTICAST - Set to enable multicast frames
|
|
CONFIG_TIVA_PROMISCUOUS - Set to enable promiscuous mode
|
|
CONFIG_TIVA_BADCRC - Set to enable bad CRC rejection.
|
|
CONFIG_TIVA_DUMPPACKET - Dump each packet received/sent to the console.
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each Stellaris LM3S8962 Evaluation Kit configuration is maintained in a
|
|
sub-directory and can be selected as follow:
|
|
|
|
tools/configure.sh lm3s8962-ek:<subdir>
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
nsh:
|
|
Configures the NuttShell (nsh) located at examples/nsh.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. This configuration uses Cygwin under Windows with the NuttX buildroot
|
|
tool chain. This is eaily change by modifying the following:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM_TOOLCHAIN_BUILDROOT=y
|
|
|
|
3. The configuration enables both the serial and telnetd NSH interfaces.
|
|
|
|
4. As it is configured now, you MUST have a network connected. Otherwise,
|
|
the NSH prompt will not come up because the Ethernet driver is waiting
|
|
for the network to come up. That is probably a bug in the Ethernet
|
|
driver behavior!
|
|
|
|
nx
|
|
An example using the NuttX graphics system (NX). This example
|
|
focuses on general window controls, movement, mouse and keyboard
|
|
input.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. This configuration uses Cygwin under Windows with the NuttX buildroot
|
|
tool chain. This is eaily change by modifying the following:
|
|
|
|
CONFIG_HOST_WINDOWS=y
|
|
CONFIG_WINDOWS_CYGWIN=y
|
|
CONFIG_ARM_TOOLCHAIN_BUILDROOT=y
|