40cd67eee6
Gregory Nutt has submitted the SGA and we can migrate the licenses to Apache. Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
312 lines
13 KiB
C
312 lines
13 KiB
C
/****************************************************************************
|
|
* boards/arm/lpc17xx_40xx/mbed/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_LPC17XX_40XX_MBED_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_LPC17XX_40XX_MBED_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* NOTE:
|
|
* The following definitions require lpc17_40_syscon.h.
|
|
* It is not included here because the including C file may not have that
|
|
* file in its include path.
|
|
*/
|
|
|
|
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency */
|
|
#define BOARD_OSCCLK_FREQUENCY BOARD_XTAL_FREQUENCY /* Main oscillator frequency */
|
|
#define BOARD_RTCCLK_FREQUENCY (32000) /* RTC oscillator frequency */
|
|
#define BOARD_INTRCOSC_FREQUENCY (4000000) /* Internal RC oscillator frequency */
|
|
|
|
/* This is the clock setup we configure for:
|
|
*
|
|
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Select Main oscillator for source
|
|
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz -> PLL0 multiplier=20, pre-divider=1
|
|
* CCLCK = 480MHz / 6 = 80MHz -> CCLK divider = 6
|
|
*/
|
|
|
|
#define LPC17_40_CCLK 80000000 /* 80Mhz*/
|
|
|
|
/* Select the main oscillator as the frequency source.
|
|
* SYSCLK is then the frequency of the main oscillator.
|
|
*/
|
|
|
|
#undef CONFIG_LPC17_40_MAINOSC
|
|
#define CONFIG_LPC17_40_MAINOSC 1
|
|
#define BOARD_SCS_VALUE SYSCON_SCS_OSCEN
|
|
|
|
/* Select the main oscillator and CCLK divider.
|
|
* The output of the divider is CCLK.
|
|
* The input to the divider (PLLCLK) will be determined by the PLL output.
|
|
*/
|
|
|
|
#define BOARD_CCLKCFG_DIVIDER 6
|
|
#define BOARD_CCLKCFG_VALUE ((BOARD_CCLKCFG_DIVIDER-1) << SYSCON_CCLKCFG_SHIFT)
|
|
|
|
/* PLL0.
|
|
* PLL0 is used to generate the CPU clock divider input (PLLCLK).
|
|
*
|
|
* Source clock: Main oscillator
|
|
* PLL0 Multiplier value (M): 20
|
|
* PLL0 Pre-divider value (N): 1
|
|
*
|
|
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz
|
|
*/
|
|
|
|
#undef CONFIG_LPC17_40_PLL0
|
|
#define CONFIG_LPC17_40_PLL0 1
|
|
#define BOARD_CLKSRCSEL_VALUE SYSCON_CLKSRCSEL_MAIN
|
|
|
|
#define BOARD_PLL0CFG_MSEL 20
|
|
#define BOARD_PLL0CFG_NSEL 1
|
|
#define BOARD_PLL0CFG_VALUE \
|
|
(((BOARD_PLL0CFG_MSEL-1) << SYSCON_PLL0CFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL0CFG_NSEL-1) << SYSCON_PLL0CFG_NSEL_SHIFT))
|
|
|
|
/* PLL1 -- Not used. */
|
|
|
|
#undef CONFIG_LPC17_40_PLL1
|
|
#define BOARD_PLL1CFG_MSEL 36
|
|
#define BOARD_PLL1CFG_NSEL 1
|
|
#define BOARD_PLL1CFG_VALUE \
|
|
(((BOARD_PLL1CFG_MSEL-1) << SYSCON_PLL1CFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL1CFG_NSEL-1) << SYSCON_PLL1CFG_NSEL_SHIFT))
|
|
|
|
/* USB divider.
|
|
* This divider is used when PLL1 is not enabled to get the
|
|
* USB clock from PLL0:
|
|
*
|
|
* USBCLK = PLL0CLK / 10 = 48MHz
|
|
*/
|
|
|
|
#define BOARD_USBCLKCFG_VALUE SYSCON_USBCLKCFG_DIV10
|
|
|
|
/* FLASH Configuration */
|
|
|
|
#undef CONFIG_LPC17_40_FLASH
|
|
#define CONFIG_LPC17_40_FLASH 1
|
|
#define BOARD_FLASHCFG_VALUE 0x0000303a
|
|
|
|
/* Ethernet configuration */
|
|
|
|
//#define ETH_MCFG_CLKSEL_DIV ETH_MCFG_CLKSEL_DIV44
|
|
#define ETH_MCFG_CLKSEL_DIV ETH_MCFG_CLKSEL_DIV20
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* The MBED has 4 LEDs along the bottom of the board. Blue or off.
|
|
* If CONFIG_ARCH_LEDS is defined, the LEDs will be controlled as follows
|
|
* for NuttX debug functionality (where NC means "No Change").
|
|
*
|
|
* During the boot phases.
|
|
* LED1 and LED2 will show boot status. LED3/4 Not used.
|
|
*/
|
|
/* LED1 LED2 */
|
|
#define LED_STARTED 0 /* OFF OFF */
|
|
#define LED_HEAPALLOCATE 1 /* BLUE OFF */
|
|
#define LED_IRQSENABLED 2 /* OFF BLUE */
|
|
#define LED_STACKCREATED 3 /* OFF OFF */
|
|
|
|
/* After the system is booted, this logic will no longer use LEDs 1 & 2.
|
|
* They are available together with LED3 for use the application software
|
|
* using lpc17_40_led (prototyped below)
|
|
*/
|
|
/* LED1 LED2 LED3 LED4 */
|
|
#define LED_INIRQ 4 /* NC NC NC ON (momentary) */
|
|
#define LED_SIGNAL 5 /* NC NC NC ON (momentary) */
|
|
#define LED_ASSERTION 6 /* NC NC NC ON (momentary) */
|
|
#define LED_PANIC 7 /* NC NC NC ON (1Hz flashing) */
|
|
|
|
#define GPIO_SSP0_SCK GPIO_SSP0_SCK_1
|
|
#define GPIO_SSP0_SSEL GPIO_SSP0_SSEL_1
|
|
#define GPIO_SSP0_MISO GPIO_SSP0_MISO_1
|
|
#define GPIO_SSP0_MOSI GPIO_SSP0_MOSI_1
|
|
|
|
/* We need to redefine USB_PWRD as GPIO to get USB Host working
|
|
* Also remember to add 2 resistors of 15K to D+ and D- pins.
|
|
*/
|
|
|
|
#ifdef CONFIG_USBHOST
|
|
# ifdef GPIO_USB_PWRD
|
|
# undef GPIO_USB_PWRD
|
|
# define GPIO_USB_PWRD (GPIO_INPUT | GPIO_PORT1 | GPIO_PIN22)
|
|
# endif
|
|
#endif
|
|
|
|
/* Alternate pin selections *************************************************/
|
|
|
|
/* Pin Description Connector On Board Base Board
|
|
* -------------------------------- --------- -------------- ----------------
|
|
* P0[0]/RD1/TXD3/SDA1 J6-9 I2C E2PROM SDA TXD3/SDA1
|
|
* P0[1]/TD1/RXD3/SCL J6-10 RXD3/SCL1
|
|
* P0[2]/TXD0/AD0[7] J6-21
|
|
* P0[3]/RXD0/AD0[6] J6-22
|
|
* P0[4]/I2SRX-CLK/RD2/CAP2.0 J6-38 CAN_RX2
|
|
* P0[5]/I2SRX-WS/TD2/CAP2.1 J6-39 CAN_TX2
|
|
* P0[6]/I2SRX_SDA/SSEL1/MAT2[0] J6-8 SSEL1, OLED CS
|
|
* P0[7]/I2STX_CLK/SCK1/MAT2[1] J6-7 SCK1, OLED SCK
|
|
* P0[8]/I2STX_WS/MISO1/MAT2[2] J6-6 MISO1
|
|
* P0[9]/I2STX_SDA/MOSI1/MAT2[3] J6-5 MOSI1, OLED data in
|
|
* P0[10] J6-40 TXD2/SDA2
|
|
* P0[11] J6-41 RXD2/SCL2
|
|
* P0[15]/TXD1/SCK0/SCK J6-13 TXD1/SCK0
|
|
* P0[16]/RXD1/SSEL0/SSEL J6-14 RXD1/SSEL0
|
|
* P0[17]/CTS1/MISO0/MISO J6-12 MISO0
|
|
* P0[18]/DCD1/MOSI0/MOSI J6-11 MOSI0
|
|
* P0[19]/DSR1/SDA1 PAD17 N/A
|
|
* P0[20]/DTR1/SCL1 PAD18 I2C E2PROM SCL N/A
|
|
* P0[21]/RI1/MCIPWR/RD1 J6-23
|
|
* P0[22]/RTS1/TD1 J6-24 LED
|
|
* P0[23]/AD0[0]/I2SRX_CLK/CAP3[0] J6-15 AD0.0
|
|
* P0[24]/AD0[1]/I2SRX_WS/CAP3[1] J6-16 AD0.1
|
|
* P0[25]/AD0[2]/I2SRX_SDA/TXD3 J6-17 AD0.2
|
|
* P0[26]/AD0[3]/AOUT/RXD3 J6-18 AD0.3/AOUT / RGB LED
|
|
* P0[27]/SDA0/USB_SDA J6-25
|
|
* P0[28]/SCL0 J6-26
|
|
* P0[29]/USB_D+ J6-37 USB_D+
|
|
* P0[30]/USB_D- J6-36 USB_D-
|
|
*/
|
|
|
|
#define GPIO_UART3_TXD GPIO_UART3_TXD_1
|
|
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1
|
|
#define GPIO_UART3_RXD GPIO_UART3_RXD_1
|
|
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1
|
|
#define GPIO_SSP1_SCK GPIO_SSP1_SCK_1
|
|
#define GPIO_UART2_TXD GPIO_UART2_TXD_1
|
|
#define GPIO_UART2_RXD GPIO_UART2_RXD_1
|
|
#define GPIO_UART1_TXD GPIO_UART1_TXD_1
|
|
#define GPIO_SSP0_SCK GPIO_SSP0_SCK_1
|
|
#define GPIO_UART1_RXD GPIO_UART1_RXD_1
|
|
#define GPIO_SSP0_SSEL GPIO_SSP0_SSEL_1
|
|
#define GPIO_SSP0_MISO GPIO_SSP0_MISO_1
|
|
#define GPIO_SSP0_MOSI GPIO_SSP0_MOSI_1
|
|
|
|
/* P1[0]/ENET-TXD0 J6-34? TXD0 TX-(Ethernet PHY)
|
|
* P1[1]/ENET_TXD1 J6-35? TXD1 TX+(Ethernet PHY)
|
|
* P1[4]/ENET_TX_EN TXEN N/A
|
|
* P1[8]/ENET_CRS CRS_DV/MODE2 N/A
|
|
* P1[9]/ENET_RXD0 J6-32? RXD0/MODE0 RD-(Ethernet PHY)
|
|
* P1[10]/ENET_RXD1 J6-33? RXD1/MODE1 RD+(Ethernet PHY)
|
|
* P1[14]/ENET_RX_ER RXER/PHYAD0 N/A
|
|
* P1[15]/ENET_REF_CLK REFCLK N/A
|
|
* P1[16]/ENET_MDC MDC N/A
|
|
* P1[17]/ENET_MDIO MDIO N/A
|
|
* P1[18]/USB_UP_LED/PWM1[1]/CAP1[0] PAD1 N/A
|
|
* P1[19]/MC0A/USB_PPWR/N_CAP1.1 PAD2 N/A
|
|
* P1[20]/MCFB0/PWM1.2/SCK0 PAD3 N/A
|
|
* P1[21]/MCABORT/PWM1.3/SSEL0 PAD4 N/A
|
|
* P1[22]/MC0B/USB-PWRD/MAT1.0 PAD5 N/A
|
|
* P1[23]/MCFB1/PWM1.4/MISO0 PAD6 N/A
|
|
* P1[24]/MCFB2/PWM1.5/MOSI0 PAD7 N/A
|
|
* P1[25]/MC1A/MAT1.1 PAD8 N/A
|
|
* P1[26]/MC1B/PWM1.6/CAP0.0 PAD9 N/A
|
|
* P1[27]/CLKOUT/USB-OVRCR-N/CAP0.1 PAD10 N/A
|
|
* P1[28]/MC2A/PCAP1.0/MAT0.0 PAD11 N/A
|
|
* P1[29]/MC2B/PCAP1.1/MAT0.1 PAD12 N/A
|
|
* P1[30]/VBUS/AD0[4] J6-19 AD0.4
|
|
* P1[31]/SCK1/AD0[5] J6-20 AD0.5
|
|
*/
|
|
|
|
#define GPIO_ENET_MDC GPIO_ENET_MDC_1
|
|
#define GPIO_ENET_MDIO GPIO_ENET_MDIO_1
|
|
|
|
/* P2[0]/PWM1.1/TXD1 J6-42 PWM1.1 / RGB LED / RS422 RX
|
|
* P2[1]/PWM1.2/RXD1 J6-43 PWM1.2 / OLED voltage / RGB LED / RS422 RX
|
|
* P2[2]/PWM1.3/CTS1/TRACEDATA[3] J6-44 PWM1.3
|
|
* P2[3]/PWM1.4/DCD1/TRACEDATA[2] J6-45 PWM1.4
|
|
* P2[4]/PWM1.5/DSR1/TRACEDATA[1] J6-46 PWM1.5
|
|
* P2[5]/PWM1[6]/DTR1/TRACEDATA[0] J6-47 PWM1.6
|
|
* P2[6]/PCAP1[0]/RI1/TRACECLK J6-48
|
|
* P2[7]/RD2/RTS1 J6-49 OLED command/data
|
|
* P2[8]/TD2/TXD2 J6-50
|
|
* P2[9]/USB_CONNECT/RXD2 PAD19 USB Pullup N/A
|
|
* P2[10]/EINT0/NMI J6-51
|
|
* P2[11]/EINT1/I2STX_CLK J6-52
|
|
* P2[12]/EINT2/I2STX_WS J6-53
|
|
* P2[13]/EINT3/I2STX_SDA J6-27
|
|
*/
|
|
|
|
#define GPIO_PWM1p1 GPIO_PWM1p1_2
|
|
#define GPIO_PWM1p2 GPIO_PWM1p2_2
|
|
#define GPIO_PWM1p3 GPIO_PWM1p3_2
|
|
#define GPIO_PWM1p4 GPIO_PWM1p4_2
|
|
#define GPIO_PWM1p5 GPIO_PWM1p5_2
|
|
#define GPIO_PWM1p6 GPIO_PWM1p6_2
|
|
|
|
/* P3[25]/MAT0.0/PWM1.2 PAD13 N/A
|
|
* P3[26]/STCLK/MAT0.1/PWM1.3 PAD14 N/A
|
|
*
|
|
* P4[28]/RX-MCLK/MAT2.0/TXD3 PAD15 N/A
|
|
* P4[29]/TX-MCLK/MAT2.1/RXD3 PAD16 N/A
|
|
*/
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: lpc17_40_led
|
|
*
|
|
* Description:
|
|
* Once the system has booted, these functions can be used to control
|
|
* LEDs 1, 2 & 3
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_ARCH_LEDS
|
|
void lpc17_40_led(int lednum, int state);
|
|
#endif
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_LPC17XX_40XX_MBED_INCLUDE_BOARD_H */
|