| .. |
|
chip
|
arch/arm/src/xmc4/: Fix USIC_BRG_SCLKCFG definition
|
2018-02-09 13:00:20 -06:00 |
|
chip.h
|
arch/: Clean up some naming and spacing.
|
2018-06-20 15:38:06 -06:00 |
|
Kconfig
|
arch/arm/src/xmc4/Kconfig: Define user friend SPI alias to follow other arch names
|
2017-11-30 12:48:07 -06:00 |
|
Make.defs
|
arch/arm/src/armv7-m/up_trigger_irq.c: Add logic to trigger ARMv7-M interrupts and exceptions.
|
2018-08-25 10:23:21 -06:00 |
|
xmc4_allocateheap.c
|
arch/: Fix an error found in build testing. The protoype of mpu_log2regionfloor() changed; an additional parameter was added. However, none of the calls to mpu_log2regionfloor() were updated to pass the new, additional parameter.
|
2018-08-24 16:40:37 -06:00 |
|
xmc4_clockconfig.c
|
Merged in david_alessio/nuttx/refactor-pll-setup (pull request #581)
|
2018-01-22 13:20:35 +00:00 |
|
xmc4_clockconfig.h
|
XMC4xxx: Add USIC baudrate calculation.
|
2017-03-19 18:11:38 -06:00 |
|
xmc4_clockutils.c
|
XMC4xxx: Clean up problems associated with USIC initialization. USIC still does not work in UART mode.
|
2017-03-21 10:55:52 -06:00 |
|
xmc4_clrpend.c
|
XMC4xxx: Add commin USIC support logic for use in all USIC configurations.
|
2017-03-19 12:48:37 -06:00 |
|
xmc4_config.h
|
Revert "arch/arm/src/xmc4/xmc4_config.h: Add a check to doubly enforce the one UART per USIC rule."
|
2017-11-25 09:44:51 -06:00 |
|
xmc4_dma.c
|
|
|
|
xmc4_dma.h
|
|
|
|
xmc4_gpio.c
|
arch/arm/src/xmc4/xmc4_gpio.c: Add a specific bit encoding for openprain GPIO pin.
|
2018-07-02 10:56:58 -06:00 |
|
xmc4_gpio.h
|
arch/arm/src/xmc4/xmc4_gpio.c: Add a specific bit encoding for openprain GPIO pin.
|
2018-07-02 10:56:58 -06:00 |
|
xmc4_i2c.c
|
|
|
|
xmc4_i2c.h
|
Make sure that labeling is used consistently in all function headers.
|
2018-02-01 10:00:02 -06:00 |
|
xmc4_idle.c
|
|
|
|
xmc4_irq.c
|
In the current implementation we only use very high priority interrupts (levels 0, 0x10 and 0x20 in CORTEX-M speak) but that means there are loads of lower priority ones that are effectively unused. I have *not* changed the semantics of these levels but have 'shifted' them to be based around the midpoint of the available interrupts (0x80) rather than at the top end....that allows for interrupts to be defined above (or, indeed, below) them as needed by the application. This should have no functional effect on existing code but adds in a clean capability to define higher priority interrupts.
|
2018-12-03 17:41:59 -06:00 |
|
xmc4_lowputc.c
|
arm/src/xmc4: Include Alt. Interrupt Enable to RX_EVENTS and rename serial GPIO configurations.
|
2017-11-25 18:13:23 -06:00 |
|
xmc4_lowputc.h
|
XMC4xxx: Plug last holes to get a first, clean build.
|
2017-03-20 13:46:02 -06:00 |
|
xmc4_mpuinit.c
|
|
|
|
xmc4_mpuinit.h
|
|
|
|
xmc4_pwm.c
|
|
|
|
xmc4_pwm.h
|
|
|
|
xmc4_serial.c
|
Make sure that labeling is used consistently in all function headers.
|
2018-02-01 10:00:02 -06:00 |
|
xmc4_spi.c
|
/arch/arm/src/xmc4: Fix XMC4 SPI. It was working only for the first transfer
|
2018-06-16 13:45:01 -06:00 |
|
xmc4_spi.h
|
arch/arm/src/xmc4: Add SPI support for Infineon XMC45xx microcontroller
|
2018-04-14 12:19:47 -06:00 |
|
xmc4_start.c
|
Squashed commit of the following:
|
2018-06-20 12:30:37 -06:00 |
|
xmc4_start.h
|
XMC4xxx: Plug last holes to get a first, clean build.
|
2017-03-20 13:46:02 -06:00 |
|
xmc4_timerisr.c
|
arch/arm/src/lpc54xx: Adds Ethernet Tx done handling.
|
2017-12-29 17:28:38 -06:00 |
|
xmc4_userspace.c
|
|
|
|
xmc4_userspace.h
|
|
|
|
xmc4_usic.c
|
XMC4xxx: Misc clock clean-up; PBDIV should be controllable from board.h
|
2017-03-21 15:05:17 -06:00 |
|
xmc4_usic.h
|
XMC4xxx: Fix a pin configuration problem. Fix some mispellings.
|
2017-03-21 11:24:04 -06:00 |
