240 lines
9.9 KiB
C
240 lines
9.9 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32f0l0g0/stm32f051-discovery/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32F0L0G0_STM32F051_DISCOVERY_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_STM32F0L0G0_STM32F051_DISCOVERY_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* Four different clock sources can be used to drive the system clock
|
|
* (SYSCLK):
|
|
*
|
|
* - HSI high-speed internal oscillator clock
|
|
* Generated from an internal 8 MHz RC oscillator
|
|
* - HSE high-speed external oscillator clock
|
|
* Normally driven by an external crystal (X3). However, this crystal is
|
|
* not fitted on the STM32F0-Discovery board.
|
|
* - PLL clock
|
|
* - MSI multispeed internal oscillator clock
|
|
* The MSI clock signal is generated from an internal RC oscillator. Seven
|
|
* frequency ranges are available: 65.536 kHz, 131.072 kHz, 262.144 kHz,
|
|
* 524.288 kHz, 1.048 MHz, 2.097 MHz (default value) and 4.194 MHz.
|
|
*
|
|
* The devices have the following two secondary clock sources
|
|
* - LSI low-speed internal RC clock
|
|
* Drives the watchdog and RTC. Approximately 37KHz
|
|
* - LSE low-speed external oscillator clock
|
|
* Driven by 32.768KHz crystal (X2) on the OSC32_IN and OSC32_OUT pins.
|
|
*/
|
|
|
|
#define STM32_BOARD_XTAL 8000000ul /* X3 on board (not fitted)*/
|
|
|
|
#define STM32_HSI_FREQUENCY 8000000ul /* Approximately 8MHz */
|
|
#define STM32_HSI14_FREQUENCY 14000000ul /* HSI14 for ADC */
|
|
#define STM32_HSI48_FREQUENCY 48000000ul /* HSI48 for USB, only some STM32F0xx */
|
|
#define STM32_HSE_FREQUENCY STM32_BOARD_XTAL
|
|
#define STM32_LSI_FREQUENCY 40000 /* Approximately 40KHz */
|
|
#define STM32_LSE_FREQUENCY 32768 /* X2 on board */
|
|
|
|
/* PLL Configuration
|
|
*
|
|
* - PLL source is HSI -> 8MHz input (nominal)
|
|
* - PLL source predivider 2 -> 4MHz divided down PLL VCO clock output
|
|
* - PLL multipler is 12 -> 48MHz PLL VCO clock output (for USB)
|
|
*
|
|
* Resulting SYSCLK frequency is 8MHz x 12 / 2 = 48MHz
|
|
*
|
|
* USB:
|
|
* If the USB interface is used in the application, it requires a precise
|
|
* 48MHz clock which can be generated from either the (1) the internal
|
|
* main PLL with the HSE clock source using an HSE crystal oscillator. In
|
|
* this case, the PLL VCO clock (defined by STM32_CFGR_PLLMUL) must be
|
|
* programmed to output a 96 MHz frequency. This is required to provide a
|
|
* 48MHz clock to the (USBCLK = PLLVCO/2). Or (2) by using the internal
|
|
* 48MHz oscillator in automatic trimming mode. The synchronization for
|
|
* this oscillator can be taken from the USB data stream itself (SOF
|
|
* signalization) which allows crystal-less operation.
|
|
* SYSCLK
|
|
* The system clock is derived from the PLL VCO divided by the output
|
|
* division factor.
|
|
* Limitations:
|
|
* - 96 MHz as PLLVCO when the product is in range 1 (1.8V),
|
|
* - 48 MHz as PLLVCO when the product is in range 2 (1.5V),
|
|
* - 24 MHz when the product is in range 3 (1.2V).
|
|
* - Output division to avoid exceeding 32 MHz as SYSCLK.
|
|
* - The minimum input clock frequency for PLL is 2 MHz (when using HSE as
|
|
* PLL source).
|
|
*/
|
|
|
|
#define STM32_CFGR_PLLSRC RCC_CFGR_PLLSRC_HSId2 /* Source is HSI/2 */
|
|
#define STM32_PLLSRC_FREQUENCY (STM32_HSI_FREQUENCY/2) /* 8MHz / 2 = 4MHz */
|
|
#ifdef CONFIG_STM32F0L0G0_USB
|
|
# undef STM32_CFGR2_PREDIV /* Not used with source HSI/2 */
|
|
# define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx12 /* PLLMUL = 12 */
|
|
# define STM32_PLL_FREQUENCY (12*STM32_PLLSRC_FREQUENCY) /* PLL VCO Frequency is 48MHz */
|
|
#else
|
|
# undef STM32_CFGR2_PREDIV /* Not used with source HSI/2 */
|
|
# define STM32_CFGR_PLLMUL RCC_CFGR_PLLMUL_CLKx12 /* PLLMUL = 12 */
|
|
# define STM32_PLL_FREQUENCY (12*STM32_PLLSRC_FREQUENCY) /* PLL VCO Frequency is 48MHz */
|
|
#endif
|
|
|
|
/* Use the PLL and set the SYSCLK source to be the divided down PLL VCO
|
|
* output frequency (STM32_PLL_FREQUENCY divided by the PLLDIV value).
|
|
*/
|
|
|
|
#define STM32_SYSCLK_SW RCC_CFGR_SW_PLL /* Use the PLL as the SYSCLK */
|
|
#define STM32_SYSCLK_SWS RCC_CFGR_SWS_PLL
|
|
#ifdef CONFIG_STM32F0L0G0_USB
|
|
# define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY /* SYSCLK frequency is PLL VCO = 48MHz */
|
|
#else
|
|
# define STM32_SYSCLK_FREQUENCY STM32_PLL_FREQUENCY /* SYSCLK frequency is PLL VCO = 48MHz */
|
|
#endif
|
|
|
|
#define STM32_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK
|
|
#define STM32_HCLK_FREQUENCY STM32_SYSCLK_FREQUENCY
|
|
|
|
/* APB1 clock (PCLK1) is HCLK (48MHz) */
|
|
|
|
#define STM32_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK
|
|
#define STM32_PCLK1_FREQUENCY (STM32_HCLK_FREQUENCY)
|
|
|
|
/* APB2 clock (PCLK2) is HCLK (48MHz) */
|
|
|
|
#define STM32_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK
|
|
#define STM32_PCLK2_FREQUENCY STM32_HCLK_FREQUENCY
|
|
#define STM32_APB2_CLKIN (STM32_PCLK2_FREQUENCY)
|
|
|
|
/* APB1 timers 1-3, 6-7, and 14-17 will receive PCLK1 */
|
|
|
|
#define STM32_APB1_TIM1_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM2_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM3_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
|
|
#define STM32_APB1_TIM6_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM7_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
|
|
#define STM32_APB1_TIM14_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM15_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM16_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
#define STM32_APB1_TIM17_CLKIN (STM32_PCLK1_FREQUENCY)
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* The STM32F0-Discovery board has four LEDs. Two of these are controlled by
|
|
* logic on the board and are not available for software control:
|
|
*
|
|
* LD1 COM: LD2 default status is red. LD2 turns to green to indicate that
|
|
* communications are in progress between the PC and the
|
|
* ST-LINK/V2.
|
|
* LD2 PWR: Red LED indicates that the board is powered.
|
|
*
|
|
* And two LEDs can be controlled by software:
|
|
*
|
|
* User LD3: Green LED is a user LED connected to the I/O PB7 of the
|
|
* STM32F051R8 MCU.
|
|
* User LD4: Blue LED is a user LED connected to the I/O PB6 of the
|
|
* STM32F051R8 MCU.
|
|
*
|
|
* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
* any way. The following definitions are used to access individual LEDs.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0 /* User LD3 */
|
|
#define BOARD_LED2 1 /* User LD4 */
|
|
#define BOARD_NLEDS 2
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
|
|
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 8 LEDs on
|
|
* board the STM32F0-Discovery.
|
|
* The following definitions describe how NuttX controls the LEDs:
|
|
*
|
|
* SYMBOL Meaning LED state
|
|
* LED1 LED2
|
|
* ------------------- ----------------------- -------- --------
|
|
* LED_STARTED NuttX has been started OFF OFF
|
|
* LED_HEAPALLOCATE Heap has been allocated OFF OFF
|
|
* LED_IRQSENABLED Interrupts enabled OFF OFF
|
|
* LED_STACKCREATED Idle stack created ON OFF
|
|
* LED_INIRQ In an interrupt No change
|
|
* LED_SIGNAL In a signal handler No change
|
|
* LED_ASSERTION An assertion failed No change
|
|
* LED_PANIC The system has crashed OFF Blinking
|
|
* LED_IDLE STM32 is is sleep mode Not used
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 0
|
|
#define LED_IRQSENABLED 0
|
|
#define LED_STACKCREATED 1
|
|
#define LED_INIRQ 2
|
|
#define LED_SIGNAL 2
|
|
#define LED_ASSERTION 2
|
|
#define LED_PANIC 3
|
|
|
|
/* Button definitions *******************************************************/
|
|
|
|
/* The STM32F0-Discovery supports two buttons; only one button is
|
|
* controllable by software:
|
|
*
|
|
* B1 USER:
|
|
* user and wake-up button connected to the I/O PA0 of the STM32F051R8.
|
|
* B2 RESET:
|
|
* pushbutton connected to NRST is used to RESET the STM32F051R8.
|
|
*/
|
|
|
|
#define BUTTON_USER 0
|
|
#define NUM_BUTTONS 1
|
|
|
|
#define BUTTON_USER_BIT (1 << BUTTON_USER)
|
|
|
|
/* Alternate Pin Functions **************************************************/
|
|
|
|
/* USART 1 */
|
|
|
|
#define GPIO_USART1_TX GPIO_USART1_TX_1
|
|
#define GPIO_USART1_RX GPIO_USART1_RX_1
|
|
|
|
/* I2C pins definition */
|
|
|
|
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1
|
|
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1
|
|
|
|
#endif /* __BOARDS_ARM_STM32F0L0G0_STM32F051_DISCOVERY_INCLUDE_BOARD_H */
|