133 lines
4.3 KiB
C
133 lines
4.3 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32wb/flipperzero/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32WB_FLIPPERZERO_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_STM32WB_FLIPPERZERO_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
#endif
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
#include "flipperzero-clocking.h"
|
|
|
|
/* Do not include STM32WB header files here */
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* USART */
|
|
|
|
#define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */
|
|
#define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */
|
|
|
|
/* SPI */
|
|
|
|
#define GPIO_SPI2_SCK GPIO_SPI2_SCK_3 /* PD1 */
|
|
#define GPIO_SPI2_MISO GPIO_SPI2_MISO_2 /* PC2 */
|
|
#define GPIO_SPI2_MOSI GPIO_SPI2_MOSI_1 /* PB15 */
|
|
|
|
/* LEDs */
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
* defined. In that case, the usage by the board port is defined in
|
|
* include/board.h and src/stm32_autoleds.c.
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 0
|
|
#define LED_IRQSENABLED 0
|
|
#define LED_STACKCREATED 1
|
|
#define LED_INIRQ 1
|
|
#define LED_SIGNAL 2
|
|
#define LED_ASSERTION 2
|
|
#define LED_PANIC 1
|
|
|
|
/* Buttons */
|
|
|
|
#define BUTTON_SW1 0 /* PC4, needs SB47 close */
|
|
#define BUTTON_SW2 1 /* PD0 */
|
|
#define BUTTON_SW3 2 /* PD1 */
|
|
#define NUM_BUTTONS 3
|
|
|
|
#define BUTTON_SW1_BIT (1 << BUTTON_SW1)
|
|
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
|
|
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
|
|
|
|
/* LCD */
|
|
|
|
#define STM32WB_LCD_SPINO 2 /* SPI2 */
|
|
|
|
#define STM32WB_LCD_CS (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_5MHz |\
|
|
GPIO_OUTPUT_SET | GPIO_PORTC | GPIO_PIN11)
|
|
#define STM32WB_LCD_RST (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_5MHz |\
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN0)
|
|
#define STM32WB_LCD_A0 (GPIO_OUTPUT | GPIO_PUSHPULL | GPIO_SPEED_5MHz |\
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN1)
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: stm32wb_board_initialize
|
|
*
|
|
* Description:
|
|
* All STM32WB architectures must provide the following entry point.
|
|
* This entry point is called early in the initialization -- after all
|
|
* memory has been configured and mapped but before any devices have been
|
|
* initialized.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void stm32wb_board_initialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_STM32WB_FLIPPERZERO_INCLUDE_BOARD_H */
|