sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
4ec7af779d
nuttx/boards/arm/tiva/tm4c129e-launchpad/README.txt
chao an 5945f080b9 boars/spawn_proxy: remove all CONFIG_POSIX_SPAWN_PROXY_STACKSIZE 
Signed-off-by: chao an <anchao@xiaomi.com>
2023-04-27 17:35:58 +08:00

331 lines
11 KiB
Plaintext
Raw Blame History

README
======
This is the README file for a port of NuttX to the TM4C129E Crypto Connected
LaunchPad (more correctly, the EK-TM4C129EXL). For more information about this
board, see https://www.ti.com/tool/EK-TM4C129EXL.
Contents
========
- EK-TM4C1294XL and DK-TM4C129X
- Status
- Directory Structure
- Development Environment
- Toolchains
- Debugging
- Hardware
- MCU Clocking
- Serial Console
- GPIOs
- Buttons
- LEDs
- GPIOs
- Configurations
- nsh
- ipv6
- ostest
EK-TM4C1294XL and DK-TM4C129X
=============================
This board configuration derives from the EK-TM4C1294XL, which in turn derives
from the DK-T4C129X. Refer to the following README files for additional
information that may be relevant to this board as well:
boards/arm/tiva/tm4c1294-launchpad/README.txt
boards/arm/tiva/dk-tm4c129x/README.txt
Status
======
This port boots NuttX through to a functional NSH prompt.
Directory Structure
===================
Layout for board support package directories:
$TOPDIR/boards/ - Directory containing BSP subdirectories
arch - CPU architecture (e.g., arm)
chip - Chip type (e.g., tiva)
Within chip subdirectory:
<board> - Subdirectory for each board (e.g., LaunchPad129)
drivers - Board-specific drivers
include - Board-specific headers
scripts - Board-specific build scripts (e.g., linker, Make.defs)
src - Board-specific code
tools - Board-specific tools or scripts (e.g., OpenOCD startup)
configs/ - Subdirectory for one or more board configuration(s)
<config_1..n> - Configuration for use with tools/configure.sh or .bat
Development Environment
=======================
Toolchains
----------
An appropriate ARM toolchain is needed, such as:
* The toolchain built with the customized NuttX buildroot
* The ready-made GNU Tools for Arm Embedded Processors:
https://developer.arm.com/Tools%20and%20Software/GNU%20Toolchain
* The toolchain that installs with Texas Instruments Code Composer Studio
(CCS): https://www.ti.com/tool/CCSTUDIO
Debugging
---------
The board incorporates an In-Circuit Debug Interface (ICDI) which allows
FLASH programming and JTAG debugging. This is accessible via the Micro-USB
Type B connector labeled DEBUG (opposite end of the board from the Ethernet
port). The ICDI interface is implemented by a TM4C123G microcontroller.
To debug with OpenOCD and arm-nuttx-eabi-gdb:
* Use 'make menuconfig' to set CONFIG_DEBUG_SYMBOLS and CONFIG_DEBUG_NOOPT.
To see debug output, e.g., the "ABCDE" printed in __start(), also set
CONFIG_DEBUG_FEATURES.
* Build NuttX.
* Flash the code using:
$ openocd -f board/ek-tm4c1294xl.cfg -c "init" -c "reset halt" \
-c "stellaris mass_erase 0" -c "flash write_bank 0 nuttx.bin"
NOTE: The above command might fail unless either: udev rules have been
configured on the development system (preferred) or the command is run as
root with 'sudo' (not encouraged). See:
- https://openocd.org/doc/html/Running.html
- https://forgge.github.io/theCore/guides/running-openocd-without-sudo.html
* Start GDB with:
$ arm-nuttx-eabi-gdb -tui nuttx
* In GDB:
(gdb) target remote localhost:3333
(gdb) monitor reset halt
(gdb) load
Hardware
========
MCU Clocking
------------
By default, the MCU on this board is clocked from 25 MHz crystal Y1, also
required for clocking the TM4C129's internal Ethernet MAC and PHY. For core
and peripheral timing, the MCU's internal PLL multiplies this 25 MHz clock
to 120 MHz.
The MCU's Hibernation peripheral is clocked from 32.768-KHz crystal Y3.
Serial Console
--------------
These configurations use UART0 for the serial console.
By default (check jumper settings on the board), UART0 is connected to the
on-board ICDI interface and is forwarded through the ICDI virtual UART. On
the PC, this appears a Virtual COM Port over the same Micro-USB Type B
connection used for programming/debugging.
On Debian Linux, this shows up as /dev/ttyACM0. Other operating systems may
differ.
Buttons
-------
The board has two on-board pushbuttons accessible to software. These are
connected to GPIO pins PJ0 and PJ1.
In addition, the board also has a Reset switch and a Wake switch. The Reset
switch asserts the reset signal to the microcontroller, the Breadboard
headers, and the BoosterPack headers and, therefore, any attached
BoosterPack boards. The Wake switch is provided as one of the means to wake
the microcontroller from hibernate mode.
LEDs
----
The board has four LEDs which are accessible to software. LEDs D1 and D2 are
connected to GPIOs PN1 and PN0 and are dedicated for software use. LEDs D3
and D4 are connected to GPIOs PF4 and PF0 and can be controlled either by
software or by the integrated Ethernet PHY of the TM4C129ENCPDT.
GPIOs
-----
The board exposes almost all MCU pins to the breadboard and BoosterPack
connectors.
Configurations
==============
Each EK-TM4C129EXL configuration is maintained in a sub-directory and can be
selected as follow:
tools/configure.sh tm4c129e-launchpad:<subdir>
Where <subdir> is one of the following:
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
configuration enables the serial ICDI virtual UART on UART0. Support for
builtin applications is enabled, but in the base configuration no builtin
applications are selected.
NOTES:
1. This configuration uses the mconf-based configuration tool. To change
this configuration using that tool, you should:
a. Build and install the kconfig-mconf tool. See nuttx/README.txt see
additional README.txt files in the NuttX tools repository.
b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.
2. By default, this configuration uses the GNU ARM EABI toolchain
(Linaro) such as the one delivered with TI's Code Composer
Studio (CCS) and builds under Linux. (Cygwin / MSYS / MSYS2 under
Windows might work as well.) These options can be reconfigured
with 'make menuconfig' as described above.
CONFIG_HOST_LINUX=y : Linux (Cygwin under Windows okay too).
CONFIG_ARCH_TOOLCHAIN_GNU=y : GNU toolchain (arm-none-eabi-gcc)
CONFIG_ARM_TOOLCHAIN_GNU_EABIL=y
CONFIG_RAW_BINARY=y : Output formats: ELF and raw binary
3. Default stack sizes are large and should really be tuned to reduce the
RAM footprint:
CONFIG_SCHED_HPWORKSTACKSIZE=2048
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_INIT_STACKSIZE=2048
CONFIG_PTHREAD_STACK_DEFAULT=2048
CONFIG_POSIX_SPAWN_DEFAULT_STACKSIZE=2048
CONFIG_BUILTIN_PROXY_STACKSIZE=1024
CONFIG_SYSTEM_TELNETD_STACKSIZE=2048
CONFIG_SYSTEM_TELNETD_SESSION_STACKSIZE=2048
4. This configuration has the network enabled by default. See the paragraph
"Using the network with NSH" in the DK-TM4C129X README).
Networking can easily be disabled or reconfigured with 'make menuconfig'
if desired.
By default:
This configuration assumes a DHCP network.
The network initialization thread is enabled. NSH will create
a separate thread when it starts to initialize the network.
This eliminates start-up delays to bring up the network.
The persistent network monitor thread is enabled. It monitors
changes in link status, takes the network down when the link is
lost (e.g., cable disconnected), abd brings the network back up
when the link becomes available again (e.g., cable connected).
The Ethernet MAC address is factory-programmed into the non-volatile
USER0 and USER1 registers. If CONFIG_TIVA_BOARDMAC is defined, the
function tiva_ethernetmac() will obtain the MAC address from these
registers and use it.
ipv6:
----
This is another version of the NuttShell configuration. It is very similar
to the nsh configuration except that it has IPv6 enabled and IPv4 disabled.
Several network utilities that are not yet available under IPv6 are
disabled.
NOTES:
1. As of 2022-09-06, this configuration was identical to the nsh
configuration other than using IPv6. So all of the notes above regarding
the nsh configuration apply.
Telnet does work with IPv6 but is not enabled in this configuration (but
could be).
2. This configuration can be modified so that both IPv4 and IPv6 are
supported. Here is a summary of the additional configuration settings
required to support both IPv4 and IPv6:
CONFIG_NET_IPv4=y
CONFIG_NET_ARP=y
CONFIG_NET_ARP_SEND=y (optional)
CONFIG_NET_ICMP=y
CONFIG_NET_ICMP_SOCKET=y
CONFIG_NETDB_DNSCLIENT=y
CONFIG_NETUTILS_TELNETD=y
CONFIG_NSH_IPADDR=0x0a000002
CONFIG_NSH_DRIPADDR=0x0a000001
CONFIG_NSH_NETMASK=0xffffff00
CONFIG_NSH_TELNET=y
Then from NSH, you have both ping and ping6 commands:
nsh> ping 10.0.0.1
nsh> ping6 fc00::1
And from the host you can do similar:
ping 10.0.0.2
ping6 fc00::2 (Linux)
ping -6 fc00::2 (Windows cmd)
and Telnet is now enabled and works from the host... but only using IPv6
addressing:
telnet fc00::2
That is because the Telnet daemon will default to IPv6 and there is no
Telnet option to let you select which if both IPv4 and IPv6 are enabled.
3. You can enable IPv6 autonomous address configuration with the following
changes to the configuration:
+ CONFIG_NET_ICMPv6_AUTOCONF=y
+ CONFIG_ICMPv6_AUTOCONF_DELAYMSEC=100
+ CONFIG_ICMPv6_AUTOCONF_MAXTRIES=5
- CONFIG_NSH_DRIPv6ADDR_1=0xfc00
- CONFIG_NSH_DRIPv6ADDR_2=0x0000
- CONFIG_NSH_DRIPv6ADDR_3=0x0000
- CONFIG_NSH_DRIPv6ADDR_4=0x0000
- CONFIG_NSH_DRIPv6ADDR_5=0x0000
- CONFIG_NSH_DRIPv6ADDR_6=0x0000
- CONFIG_NSH_DRIPv6ADDR_7=0x0000
- CONFIG_NSH_DRIPv6ADDR_8=0x0001
- CONFIG_NSH_IPv6ADDR_1=0xfc00
- CONFIG_NSH_IPv6ADDR_2=0x0000
- CONFIG_NSH_IPv6ADDR_3=0x0000
- CONFIG_NSH_IPv6ADDR_4=0x0000
- CONFIG_NSH_IPv6ADDR_5=0x0000
- CONFIG_NSH_IPv6ADDR_6=0x0000
- CONFIG_NSH_IPv6ADDR_7=0x0000
- CONFIG_NSH_IPv6ADDR_8=0x0002
- CONFIG_NSH_IPv6NETMASK_1=0xffff
- CONFIG_NSH_IPv6NETMASK_2=0xffff
- CONFIG_NSH_IPv6NETMASK_3=0xffff
- CONFIG_NSH_IPv6NETMASK_4=0xffff
- CONFIG_NSH_IPv6NETMASK_5=0xffff
- CONFIG_NSH_IPv6NETMASK_6=0xffff
- CONFIG_NSH_IPv6NETMASK_7=0xffff
- CONFIG_NSH_IPv6NETMASK_8=0xff80
ostest:
------
This configuration is the same as 'nsh' described above, with the addition
of CONFIG_TESTING_OSTEST. This enables the built-in program 'ostest' which
runs a series of tests to exercise features of the operating system. This
configuration also enables several debugging options to assist with
diagnosing any failures.
Reference in New Issue View Git Blame Copy Permalink