117 lines
3.4 KiB
C
117 lines
3.4 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32/stm32f4discovery/src/stm32_ssd1351.c
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include <debug.h>
|
|
|
|
#include <nuttx/arch.h>
|
|
#include <nuttx/board.h>
|
|
#include <nuttx/spi/spi.h>
|
|
#include <nuttx/lcd/lcd.h>
|
|
#include <nuttx/lcd/ssd1351.h>
|
|
|
|
#include "stm32_gpio.h"
|
|
#include "stm32_spi.h"
|
|
|
|
#include "stm32f4discovery.h"
|
|
|
|
#ifdef CONFIG_LCD_SSD1351
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Configuration ************************************************************/
|
|
|
|
/* The pin configurations here require that SPI1 is selected */
|
|
|
|
#ifndef CONFIG_STM32_SPI1
|
|
# error "The OLED driver requires CONFIG_STM32_SPI1 in the configuration"
|
|
#endif
|
|
|
|
#ifndef CONFIG_SSD1351_SPI4WIRE
|
|
# error "The configuration requires the SPI 4-wire interface"
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: board_graphics_setup
|
|
*
|
|
* Description:
|
|
* Called by NX initialization logic to configure the OLED.
|
|
*
|
|
****************************************************************************/
|
|
|
|
struct lcd_dev_s *board_graphics_setup(unsigned int devno)
|
|
{
|
|
struct spi_dev_s *spi;
|
|
struct lcd_dev_s *dev;
|
|
|
|
/* Configure the OLED GPIOs. This initial configuration is RESET low,
|
|
* putting the OLED into reset state.
|
|
*/
|
|
|
|
stm32_configgpio(GPIO_OLED_RESET);
|
|
|
|
/* Wait a bit then release the OLED from the reset state */
|
|
|
|
up_mdelay(20);
|
|
stm32_gpiowrite(GPIO_OLED_RESET, true);
|
|
|
|
/* Get the SPI1 port interface */
|
|
|
|
spi = stm32_spibus_initialize(1);
|
|
if (spi == NULL)
|
|
{
|
|
lcderr("ERROR: Failed to initialize SPI port 1\n");
|
|
}
|
|
else
|
|
{
|
|
/* Bind the SPI port to the OLED */
|
|
|
|
dev = ssd1351_initialize(spi, devno);
|
|
if (dev == NULL)
|
|
{
|
|
lcderr("ERROR: Failed to bind SPI port 1 to OLED %d\n", devno);
|
|
}
|
|
else
|
|
{
|
|
lcdinfo("Bound SPI port 1 to OLED %d\n", devno);
|
|
|
|
/* And turn the OLED on */
|
|
|
|
dev->setpower(dev, LCD_FULL_ON);
|
|
return dev;
|
|
}
|
|
}
|
|
|
|
return NULL;
|
|
}
|
|
|
|
#endif /* CONFIG_LCD_SSD1351 */
|