55a4029885
configs: spresense: add basic LCD configuration
* arch: arm: cxd56xx: add Graphics Engine
Add driver for hardware image processor device
to enable the hardware image processor set CXD56_GE2D=true
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: lcd: add ILI9340 LCD Single Chip Driver
LCD Single Chip Driver, ILI9340, ILI Technology Corp.
Required LCD driver settings:
LCD_MAXCONTRAST should be 255, but any value >0 and <=255 will be accepted.
LCD_MAXPOWER should be 1: 0=off, 1=on
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* drivers: lcd: JDI LPM013M091A LCD Driver
JDI LPM013M091A LCD Driver.
This driver doesn't support reading data.
Recommended to use DMA to transfer data or displayed image would be
broken.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add basic LCD configuration
add basic LCD configuration for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add lpm013m091a LCD
add device configuration for lpm013m091a LCD on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add ili9340 LCD
add device configuration for ili9340 LCD on spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* configs: spresense: add defconfig with LCD
add defconfig with LCD for spresense board
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
291 lines
10 KiB
C
291 lines
10 KiB
C
/****************************************************************************
|
|
* configs/spresense/include/board.h
|
|
*
|
|
* Copyright 2018 Sony Semiconductor Solutions Corporation
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name of Sony Semiconductor Solutions Corporation nor
|
|
* the names of its contributors may be used to endorse or promote
|
|
* products derived from this software without specific prior written
|
|
* permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef _CONFIGS_SPRESENSE_INCLUDE_BOARD_H
|
|
#define _CONFIGS_SPRESENSE_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#include <nuttx/irq.h>
|
|
#include <sys/boardctl.h>
|
|
#include <stdbool.h>
|
|
|
|
#include "cxd56_clock.h"
|
|
#include "cxd56_power.h"
|
|
#include "cxd56_flash.h"
|
|
#include "cxd56_gauge.h"
|
|
#include "cxd56_charger.h"
|
|
#include "cxd56_gs2200m.h"
|
|
#include "cxd56_i2cdev.h"
|
|
#include "cxd56_bmi160.h"
|
|
#include "cxd56_sdcard.h"
|
|
#include "cxd56_wdt.h"
|
|
#include "cxd56_gpioif.h"
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking ****************************************************************/
|
|
|
|
#define BOARD_XTAL_FREQUENCY (26000000) /* XTAL oscillator frequency */
|
|
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency */
|
|
#define BOARD_INTRCOSC_FREQUENCY (8192000) /* Internal RC oscillator frequency */
|
|
|
|
#ifdef CONFIG_CXD56_80MHz
|
|
# define BOARD_FCLKOUT_FREQUENCY (80000000)
|
|
#else
|
|
# define BOARD_FCLKOUT_FREQUENCY (97500000)
|
|
#endif
|
|
|
|
#define CXD56_CCLK BOARD_FCLKOUT_FREQUENCY
|
|
|
|
/* USB0 ********************************************************************/
|
|
|
|
#define BOARD_USB0_CLKSRC PLL0USB_CLKSEL_XTAL
|
|
#define BOARD_USB0_MDIV 0x06167ffa /* Table 149 datsheet, valid for 12Mhz Fclkin */
|
|
#define BOARD_USB0_NP_DIV 0x00302062 /* Table 149 datsheet, valid for 12Mhz Fclkin */
|
|
|
|
/* SPIFI clocking **********************************************************/
|
|
|
|
/* The SPIFI will receive clocking from a divider per the settings provided
|
|
* in this file. The NuttX code will configure PLL1 as the input clock
|
|
* for the selected divider
|
|
*/
|
|
|
|
#undef BOARD_SPIFI_PLL1 /* No division */
|
|
#undef BOARD_SPIFI_DIVA /* Supports division by 1-4 */
|
|
#undef BOARD_SPIFI_DIVB /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVC /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVD /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVE /* Supports division by 1-256 */
|
|
|
|
#if BOARD_FCLKOUT_FREQUENCY < 20000000
|
|
# define BOARD_SPIFI_PLL1 1 /* Use PLL1 directly */
|
|
#else
|
|
# define BOARD_SPIFI_DIVB 1 /* Use IDIVB */
|
|
#endif
|
|
|
|
/* We need to configure the divider so that its output is as close to the
|
|
* desired SCLK value. The peak data transfer rate will be about half of
|
|
* this frequency in bytes per second.
|
|
*/
|
|
|
|
#if BOARD_FCLKOUT_FREQUENCY < 20000000
|
|
# define BOARD_SPIFI_FREQUENCY BOARD_FCLKOUT_FREQUENCY /* 72Mhz? */
|
|
#else
|
|
# define BOARD_SPIFI_DIVIDER (14) /* 204MHz / 14 = 14.57MHz */
|
|
# define BOARD_SPIFI_FREQUENCY (102000000) /* 204MHz / 14 = 14.57MHz */
|
|
#endif
|
|
|
|
/* UART clocking ***********************************************************/
|
|
|
|
/* Configure all UARTs to use the XTAL input frequency */
|
|
|
|
#define BOARD_UART0_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
#define BOARD_UART1_BASEFREQ 48750000
|
|
#define BOARD_UART2_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
|
|
/* LED definitions *********************************************************/
|
|
|
|
#define GPIO_LED1 (PIN_I2S1_BCK)
|
|
#define GPIO_LED2 (PIN_I2S1_LRCK)
|
|
#define GPIO_LED3 (PIN_I2S1_DATA_IN)
|
|
#define GPIO_LED4 (PIN_I2S1_DATA_OUT)
|
|
|
|
#define BOARD_LED1 (0)
|
|
#define BOARD_LED2 (1)
|
|
#define BOARD_LED3 (2)
|
|
#define BOARD_LED4 (3)
|
|
#define BOARD_NLEDS (4)
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
#define BOARD_LED3_BIT (1 << BOARD_LED3)
|
|
#define BOARD_LED4_BIT (1 << BOARD_LED4)
|
|
|
|
/* LED pattern for use with board_autoled_on() and board_autoled_off() */
|
|
|
|
#define LED_STARTED (BOARD_LED1_BIT)
|
|
#define LED_HEAPALLOCATE (BOARD_LED2_BIT)
|
|
#define LED_IRQSENABLED (BOARD_LED1_BIT | BOARD_LED2_BIT)
|
|
#define LED_STACKCREATED (BOARD_LED3_BIT)
|
|
#define LED_INIRQ (BOARD_LED1_BIT | BOARD_LED3_BIT)
|
|
#define LED_SIGNAL (BOARD_LED2_BIT | BOARD_LED3_BIT)
|
|
#define LED_ASSERTION (BOARD_LED1_BIT | BOARD_LED2_BIT | BOARD_LED3_BIT)
|
|
#define LED_PANIC (BOARD_LED4_BIT)
|
|
|
|
/* Buttons definitions *****************************************************/
|
|
|
|
#define BOARD_NUM_BUTTONS (2)
|
|
|
|
/* Power Control definitions ***********************************************/
|
|
|
|
/* Switch Device
|
|
* --------- -------------------------------
|
|
* LSW2 AcaPulco Audio Digital VDD
|
|
* LSW3 SPI-Flash & TCXO
|
|
* LSW4 GNSS LNA
|
|
* GPO0 AcaPulco Audio Analog VDD
|
|
* GPO1 Sensor 1.8V
|
|
* GPO2 Sensor 3.3V
|
|
* GPO3 Bluetooth/Bluetooth Low Energy
|
|
* GPO4 Image Sensor 1.2V
|
|
* GPO5 Image Sensor 3.3V
|
|
* GPO6 eMMC 3.3V/1.8V
|
|
* GPO7 Image Sensor 1.8V
|
|
*
|
|
*/
|
|
|
|
#define PMIC_NONE (0)
|
|
#define PMIC_TYPE_LSW (1u << 8)
|
|
#define PMIC_TYPE_GPO (1u << 9)
|
|
#define PMIC_TYPE_DDCLDO (1u << 10)
|
|
#define PMIC_GET_TYPE(v) ((v) & 0xff00)
|
|
#define PMIC_GET_CH(v) ((v) & 0x00ff)
|
|
#define PMIC_LSW(n) (PMIC_TYPE_LSW | (1u << (n)))
|
|
#define PMIC_GPO(n) (PMIC_TYPE_GPO | (1u << (n)))
|
|
#define PMIC_DDCLDO(n) (PMIC_TYPE_DDCLDO | (1u << (n)))
|
|
|
|
enum board_power_device
|
|
{
|
|
/* DDC/LDO */
|
|
|
|
POWER_DDC_IO = PMIC_DDCLDO(0),
|
|
POWER_LDO_EMMC = PMIC_DDCLDO(1),
|
|
POWER_DDC_ANA = PMIC_DDCLDO(2),
|
|
POWER_LDO_ANA = PMIC_DDCLDO(3),
|
|
POWER_DDC_CORE = PMIC_DDCLDO(4),
|
|
POWER_LDO_PERI = PMIC_DDCLDO(5),
|
|
|
|
/* Load Switch */
|
|
|
|
POWER_AUDIO_DVDD = PMIC_LSW(2),
|
|
POWER_FLASH = PMIC_LSW(3),
|
|
POWER_TCXO = PMIC_LSW(3),
|
|
POWER_LNA = PMIC_LSW(4),
|
|
|
|
/* GPO */
|
|
|
|
POWER_AUDIO_AVDD = PMIC_GPO(0),
|
|
POWER_SENSOR_18V = PMIC_GPO(1),
|
|
POWER_SENSOR_33V = PMIC_GPO(2),
|
|
POWER_BMI160 = POWER_SENSOR_18V,
|
|
POWER_SENSOR = POWER_SENSOR_18V | POWER_SENSOR_33V,
|
|
POWER_BTBLE = PMIC_GPO(3),
|
|
POWER_EINK = PMIC_NONE,
|
|
POWER_EMMC = PMIC_GPO(6),
|
|
POWER_LFOUR = PMIC_NONE,
|
|
POWER_LTE = PMIC_NONE,
|
|
POWER_IMAGE_SENSOR = PMIC_GPO(4) | PMIC_GPO(5) | PMIC_GPO(7),
|
|
};
|
|
|
|
/* LCD Display clocking ****************************************************/
|
|
|
|
#define ILI9340_SPI_MAXFREQUENCY 40000000
|
|
|
|
/* Display device pin definitions ******************************************/
|
|
|
|
#if defined(CONFIG_LCD_ON_MAIN_BOARD) /* Display connected to main board. */
|
|
|
|
#define DISPLAY_RST PIN_I2S0_BCK
|
|
#define DISPLAY_DC PIN_I2S0_LRCK
|
|
|
|
#define DISPLAY_SPI 5
|
|
|
|
#else /* Display is connected through extension board. */
|
|
|
|
#define DISPLAY_RST PIN_SPI2_MISO
|
|
#define DISPLAY_DC PIN_PWM2
|
|
|
|
#define DISPLAY_SPI 4
|
|
|
|
#endif
|
|
|
|
/*
|
|
* Set signal id for notify USB device connection status and
|
|
* supply current value.
|
|
* signal returns "usbdev_notify_s" struct pointer in sival_ptr.
|
|
*
|
|
* Arg: Value of sinal number
|
|
*/
|
|
|
|
#define BOARDIOC_USBDEV_SETNOTIFYSIG (BOARDIOC_USER+0x0001)
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: cxd56_boardinitialize
|
|
*
|
|
* Description:
|
|
*
|
|
****************************************************************************/
|
|
|
|
void cxd56_boardinitialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* _CONFIGS_SPRESENSE_INCLUDE_BOARD_H */
|