247 lines
10 KiB
C
247 lines
10 KiB
C
/************************************************************************************
|
|
* configs/lpcxpresso-lpc1115/include/board.h
|
|
*
|
|
* Copyright (C) 2015 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
|
* used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
************************************************************************************/
|
|
|
|
#ifndef __CONFIG_LPCXPRESSO_LPC1115_INCLUDE_BOARD_H
|
|
#define __CONFIG_LPCXPRESSO_LPC1115_INCLUDE_BOARD_H
|
|
|
|
/************************************************************************************
|
|
* Included Files
|
|
************************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
/************************************************************************************
|
|
* Pre-processor Definitions
|
|
************************************************************************************/
|
|
|
|
/* Clocking *************************************************************************/
|
|
/* NOTE: The following definitions require lpc11_syscon.h. It is not included here
|
|
* because the including C file may not have that file in its include path.
|
|
*/
|
|
|
|
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency */
|
|
#define BOARD_OSCCLK_FREQUENCY BOARD_XTAL_FREQUENCY /* Main oscillator frequency */
|
|
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency */
|
|
#define BOARD_INTRCOSC_FREQUENCY (1200000) /* Internal RC oscillator frequency */
|
|
|
|
/* This is the clock setup we configure for:
|
|
*
|
|
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Select Main oscillator for source
|
|
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz -> PLL0 multipler=20, pre-divider=1
|
|
* MCLK = 480MHz / 6 = 80MHz -> MCLK divider = 6
|
|
*/
|
|
|
|
#define LPC11_MCLK 48000000 /* 48Mhz */
|
|
|
|
/* Select the internal RC oscillator as the frequency source. SYSCLK is then the frequency
|
|
* of the main oscillator.
|
|
*/
|
|
|
|
#undef CONFIG_LPC11_INTRCOSC
|
|
#define CONFIG_LPC11_INTRCOSC 1
|
|
#define BOARD_SCS_VALUE SYSCON_SCS_OSCEN
|
|
|
|
/* Select the main oscillator and CCLK divider. The output of the divider is CCLK.
|
|
* The input to the divider (PLLCLK) will be determined by the PLL output.
|
|
*/
|
|
|
|
#define BOARD_CCLKCFG_DIVIDER 6
|
|
#define BOARD_CCLKCFG_VALUE ((BOARD_CCLKCFG_DIVIDER-1) << SYSCON_CCLKCFG_SHIFT)
|
|
|
|
/* PLL0. PLL0 is used to generate the CPU clock divider input (PLLCLK).
|
|
*
|
|
* Source clock: Main oscillator
|
|
* PLL0 Multiplier value (M): 20
|
|
* PLL0 Pre-divider value (N): 1
|
|
*
|
|
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz
|
|
*/
|
|
|
|
#undef CONFIG_LPC11_PLL0
|
|
#define CONFIG_LPC11_PLL0 1
|
|
#define BOARD_CLKSRCSEL_VALUE SYSCON_CLKSRCSEL_MAIN
|
|
|
|
#define BOARD_PLL0CFG_MSEL 20
|
|
#define BOARD_PLL0CFG_NSEL 1
|
|
#define BOARD_PLL0CFG_VALUE \
|
|
(((BOARD_PLL0CFG_MSEL-1) << SYSCON_PLL0CFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL0CFG_NSEL-1) << SYSCON_PLL0CFG_NSEL_SHIFT))
|
|
|
|
/* PLL1 -- Not used. */
|
|
|
|
#undef CONFIG_LPC11_PLL1
|
|
#define BOARD_PLL1CFG_MSEL 36
|
|
#define BOARD_PLL1CFG_NSEL 1
|
|
#define BOARD_PLL1CFG_VALUE \
|
|
(((BOARD_PLL1CFG_MSEL-1) << SYSCON_PLL1CFG_MSEL_SHIFT) | \
|
|
((BOARD_PLL1CFG_NSEL-1) << SYSCON_PLL1CFG_NSEL_SHIFT))
|
|
|
|
/* USB divider. This divider is used when PLL1 is not enabled to get the
|
|
* USB clock from PLL0:
|
|
*
|
|
* USBCLK = PLL0CLK / 10 = 48MHz
|
|
*/
|
|
|
|
#define BOARD_USBCLKCFG_VALUE SYSCON_USBCLKCFG_DIV10
|
|
|
|
/* FLASH Configuration */
|
|
|
|
#undef CONFIG_LPC11_FLASH
|
|
#define CONFIG_LPC11_FLASH 1
|
|
#define BOARD_FLASHCFG_VALUE 0x0000303a
|
|
|
|
/* LED definitions ******************************************************************/
|
|
/* The LPCXpresso LPC1115 board has a single red LED (there are additional LEDs on
|
|
* the base board not considered here).
|
|
*/
|
|
/* ON OFF */
|
|
#define LED_STARTED 0 /* OFF ON (never happens) */
|
|
#define LED_HEAPALLOCATE 0 /* OFF ON (never happens) */
|
|
#define LED_IRQSENABLED 0 /* OFF ON (never happens) */
|
|
#define LED_STACKCREATED 1 /* ON ON (never happens) */
|
|
#define LED_INIRQ 2 /* OFF NC (momentary) */
|
|
#define LED_SIGNAL 2 /* OFF NC (momentary) */
|
|
#define LED_ASSERTION 2 /* OFF NC (momentary) */
|
|
#define LED_PANIC 0 /* OFF ON (1Hz flashing) */
|
|
|
|
/* Alternate pin selections *********************************************************/
|
|
/* Pin Description Connector On Board Base Board
|
|
* -------------------------------- --------- -------------- ---------------------
|
|
* P0[0]/RD1/TXD3/SDA1 J6-9 I2C E2PROM SDA TXD3/SDA1
|
|
* P0[1]/TD1/RXD3/SCL J6-10 RXD3/SCL1
|
|
* P0[2]/TXD0/AD0[7] J6-21
|
|
* P0[3]/RXD0/AD0[6] J6-22
|
|
* P0[4]/I2SRX-CLK/RD2/CAP2.0 J6-38 CAN_RX2
|
|
* P0[5]/I2SRX-WS/TD2/CAP2.1 J6-39 CAN_TX2
|
|
* P0[6]/I2SRX_SDA/SSEL1/MAT2[0] J6-8 SSEL1, OLED CS
|
|
* P0[7]/I2STX_CLK/SCK1/MAT2[1] J6-7 SCK1, OLED SCK
|
|
* P0[8]/I2STX_WS/MISO1/MAT2[2] J6-6 MISO1
|
|
* P0[9]/I2STX_SDA/MOSI1/MAT2[3] J6-5 MOSI1, OLED data in
|
|
* P0[10] J6-40 TXD2/SDA2
|
|
* P0[11] J6-41 RXD2/SCL2
|
|
*/
|
|
|
|
#define GPIO_UART3_TXD GPIO_UART3_TXD_1
|
|
#define GPIO_I2C1_SDA GPIO_I2C1_SDA_1
|
|
#define GPIO_UART3_RXD GPIO_UART3_RXD_1
|
|
#define GPIO_I2C1_SCL GPIO_I2C1_SCL_1
|
|
#define GPIO_SSP1_SCK GPIO_SSP1_SCK_1
|
|
#define GPIO_UART2_TXD GPIO_UART2_TXD_1
|
|
#define GPIO_UART2_RXD GPIO_UART2_RXD_1
|
|
#define GPIO_UART1_TXD GPIO_UART1_TXD_1
|
|
#define GPIO_SSP0_SCK GPIO_SSP0_SCK_1
|
|
#define GPIO_UART1_RXD GPIO_UART1_RXD_1
|
|
#define GPIO_SSP0_SSEL GPIO_SSP0_SSEL_1
|
|
#define GPIO_SSP0_MISO GPIO_SSP0_MISO_1
|
|
#define GPIO_SSP0_MOSI GPIO_SSP0_MOSI_1
|
|
|
|
/* P1[0]/ENET-TXD0 J6-34? TXD0 TX-(Ethernet PHY)
|
|
* P1[1]/ENET_TXD1 J6-35? TXD1 TX+(Ethernet PHY)
|
|
* P1[4]/ENET_TX_EN TXEN N/A
|
|
* P1[8]/ENET_CRS CRS_DV/MODE2 N/A
|
|
* P1[9]/ENET_RXD0 J6-32? RXD0/MODE0 RD-(Ethernet PHY)
|
|
* P1[10]/ENET_RXD1 J6-33? RXD1/MODE1 RD+(Ethernet PHY)
|
|
*/
|
|
|
|
#define GPIO_ENET_MDC GPIO_ENET_MDC_1
|
|
#define GPIO_ENET_MDIO GPIO_ENET_MDIO_1
|
|
|
|
/* P2[0]/PWM1.1/TXD1 J6-42 PWM1.1 / RGB LED / RS422 RX
|
|
* P2[1]/PWM1.2/RXD1 J6-43 PWM1.2 / OLED voltage / RGB LED / RS422 RX
|
|
* P2[2]/PWM1.3/CTS1/TRACEDATA[3] J6-44 PWM1.3
|
|
* P2[3]/PWM1.4/DCD1/TRACEDATA[2] J6-45 PWM1.4
|
|
* P2[4]/PWM1.5/DSR1/TRACEDATA[1] J6-46 PWM1.5
|
|
* P2[5]/PWM1[6]/DTR1/TRACEDATA[0] J6-47 PWM1.6
|
|
* P2[6]/PCAP1[0]/RI1/TRACECLK J6-48
|
|
* P2[7]/RD2/RTS1 J6-49 OLED command/data
|
|
* P2[8]/TD2/TXD2 J6-50
|
|
* P2[9]/USB_CONNECT/RXD2 PAD19 USB Pullup N/A
|
|
* P2[10]/EINT0/NMI J6-51
|
|
* P2[11]/EINT1/I2STX_CLK J6-52
|
|
*/
|
|
|
|
#define GPIO_PWM1p1 GPIO_PWM1p1_2
|
|
#define GPIO_PWM1p2 GPIO_PWM1p2_2
|
|
#define GPIO_PWM1p3 GPIO_PWM1p3_2
|
|
#define GPIO_PWM1p4 GPIO_PWM1p4_2
|
|
#define GPIO_PWM1p5 GPIO_PWM1p5_2
|
|
#define GPIO_PWM1p6 GPIO_PWM1p6_2
|
|
|
|
/* P3[25]/MAT0.0/PWM1.2 PAD13 N/A
|
|
* P3[26]/STCLK/MAT0.1/PWM1.3 PAD14 N/A
|
|
*/
|
|
|
|
/************************************************************************************
|
|
* Public Types
|
|
************************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/************************************************************************************
|
|
* Public Data
|
|
************************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/************************************************************************************
|
|
* Public Function Prototypes
|
|
************************************************************************************/
|
|
/************************************************************************************
|
|
* Name: lpc11_boardinitialize
|
|
*
|
|
* Description:
|
|
* All LPC11xx architectures must provide the following entry point. This entry point
|
|
* is called early in the intitialization -- after all memory has been configured
|
|
* and mapped but before any devices have been initialized.
|
|
*
|
|
************************************************************************************/
|
|
|
|
void lpc11_boardinitialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __CONFIG_LPCXPRESSO_LPC1115_INCLUDE_BOARD_H */
|