236 lines
8.8 KiB
C
236 lines
8.8 KiB
C
/****************************************************************************
|
|
* boards/arm/sam34/arduino-due/include/board.h
|
|
*
|
|
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
|
* used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_SAM34_ARDUINO_DUE_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_SAM34_ARDUINO_DUE_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
# include <stdbool.h>
|
|
# ifdef CONFIG_SAM34_GPIO_IRQ
|
|
# include <arch/irq.h>
|
|
# endif
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* After power-on reset, the SAM3X device is running on a 4MHz internal RC.
|
|
* These definitions will configure clocking
|
|
*
|
|
* MAINOSC: Frequency = 12MHz (crystal)
|
|
* PLLA: PLL Divider = 1, Multiplier = 14 to generate PLLACK = 168MHz
|
|
* Master Clock (MCK): Source = PLLACK, Prescalar = 1 to generate MCK = 84MHz
|
|
* CPU clock: 84MHz
|
|
*/
|
|
|
|
#define BOARD_32KOSC_FREQUENCY (32768)
|
|
#define BOARD_SCLK_FREQUENCY (BOARD_32KOSC_FREQUENCY)
|
|
#define BOARD_MAINOSC_FREQUENCY (12000000) /* MAINOSC: 12MHz crystal on-board */
|
|
|
|
/* Main oscillator register settings.
|
|
*
|
|
* The start up time should be should be:
|
|
* Start Up Time = 8 * MOSCXTST / SLCK = 56 Slow Clock Cycles.
|
|
*/
|
|
|
|
#define BOARD_CKGR_MOR_MOSCXTST (62 << PMC_CKGR_MOR_MOSCXTST_SHIFT) /* Start-up Time */
|
|
|
|
/* PLLA configuration.
|
|
*
|
|
* Divider = 1
|
|
* Multipler = 14
|
|
*/
|
|
|
|
#define BOARD_CKGR_PLLAR_MUL (13 << PMC_CKGR_PLLAR_MUL_SHIFT)
|
|
#define BOARD_CKGR_PLLAR_COUNT (63 << PMC_CKGR_PLLAR_COUNT_SHIFT)
|
|
#define BOARD_CKGR_PLLAR_DIV PMC_CKGR_PLLAR_DIV_BYPASS
|
|
|
|
/* PMC master clock register settings.
|
|
*
|
|
* Source = PLLA
|
|
* Divider = 2
|
|
*/
|
|
|
|
#define BOARD_PMC_MCKR_CSS PMC_MCKR_CSS_PLLA
|
|
#define BOARD_PMC_MCKR_PRES PMC_MCKR_PRES_DIV2
|
|
|
|
/* USB UTMI PLL start-up time */
|
|
|
|
#define BOARD_CKGR_UCKR_UPLLCOUNT (3 << PMC_CKGR_UCKR_UPLLCOUNT_SHIFT)
|
|
|
|
/* Resulting frequencies */
|
|
|
|
#define BOARD_PLLA_FREQUENCY (168000000) /* PLLACK: 14 * 12Mhz / 1 */
|
|
#define BOARD_MCK_FREQUENCY (84000000) /* MCK: PLLACK / 2 */
|
|
#define BOARD_CPU_FREQUENCY (84000000) /* CPU: MCK */
|
|
|
|
/* HSMCI clocking
|
|
*
|
|
* Multimedia Card Interface clock (MCCK or MCI_CK) is Master Clock
|
|
* (MCK) divided by (2*(CLKDIV+1)).
|
|
*
|
|
* MCI_SPEED = MCCK / (2*(CLKDIV+1))
|
|
* CLKDIV = MCCK / MCI_SPEED / 2 - 1
|
|
*
|
|
* Where CLKDIV has a range of 0-255.
|
|
*/
|
|
|
|
/* MCK = 84MHz, CLKDIV = 104,
|
|
* MCI_SPEED = 84MHz / 2 * (104+1) = 400 KHz
|
|
*/
|
|
|
|
#define HSMCI_INIT_CLKDIV (104 << HSMCI_MR_CLKDIV_SHIFT)
|
|
|
|
/* MCK = 84MHz, CLKDIV = 2, MCI_SPEED = 84MHz / 2 * (2+1) = 14 MHz */
|
|
|
|
#define HSMCI_MMCXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
|
|
|
|
/* MCK = 84MHz, CLKDIV = 1, MCI_SPEED = 84MHz / 2 * (1+1) = 21 MHz */
|
|
|
|
#define HSMCI_SDXFR_CLKDIV (1 << HSMCI_MR_CLKDIV_SHIFT)
|
|
#define HSMCI_SDWIDEXFR_CLKDIV HSMCI_SDXFR_CLKDIV
|
|
|
|
/* FLASH wait states
|
|
*
|
|
* FWS MAX FREQUENCY
|
|
* 1.62V 1.8V
|
|
* --- ----- ------
|
|
* 0 17MHz 19MHz
|
|
* 1 45MHz 50MHz
|
|
* 2 58MHz 64MHz
|
|
* 3 70MHz 80MHz
|
|
* 4 78MHz 90MHz
|
|
*/
|
|
|
|
#define BOARD_FWS 4
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* There are three user-controllable LEDs on board the Arduino Due board:
|
|
*
|
|
* LED GPIO
|
|
* ---------------- -----
|
|
* L Amber LED PB27
|
|
* TX Yellow LED PA21
|
|
* RX Yellow LED PC30
|
|
*
|
|
* LED L is connected to ground and can be illuminated by driving the PB27
|
|
* output high. The TX and RX LEDs are pulled high and can be illuminated by
|
|
* driving the corresponding
|
|
* GPIO output to low.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED_L 0
|
|
#define BOARD_LED_RX 1
|
|
#define BOARD_LED_TX 2
|
|
#define BOARD_NLEDS 3
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED_L_BIT (1 << BOARD_LED_L)
|
|
#define BOARD_LED_RX_BIT (1 << BOARD_LED_RX)
|
|
#define BOARD_LED_TX_BIT (1 << BOARD_LED_TX)
|
|
|
|
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
* defined. In that case, the usage by the board port is defined in
|
|
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
|
|
* events as follows:
|
|
*
|
|
* SYMBOL MEANING LED STATE
|
|
* L TX RX
|
|
* ----------------------- -------------------------- -------- -------- --------
|
|
*/
|
|
|
|
#define LED_STARTED 0 /* NuttX has been started OFF OFF OFF */
|
|
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF OFF */
|
|
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF OFF */
|
|
#define LED_STACKCREATED 1 /* Idle stack created ON OFF OFF */
|
|
#define LED_INIRQ 2 /* In an interrupt N/C GLOW OFF */
|
|
#define LED_SIGNAL 2 /* In a signal handler N/C GLOW OFF */
|
|
#define LED_ASSERTION 2 /* An assertion failed N/C GLOW OFF */
|
|
#define LED_PANIC 3 /* The system has crashed N/C N/C Blinking */
|
|
#define LED_PANIC 3 /* MCU is is sleep mode ------ Not used -------- */
|
|
|
|
/* Thus if LED L is statically on, NuttX has successfully booted and is,
|
|
* apparently, running normmally. If LED RX is glowing, then NuttX is
|
|
* handling interrupts (and also signals and assertions). If TX is flashing
|
|
* at approximately 2Hz, then a fatal error has been detected and the system
|
|
*/
|
|
|
|
/* Button definitions *******************************************************/
|
|
|
|
/* There are no buttons on the Arduino Due board. */
|
|
|
|
/* GPIO pin configurations **************************************************/
|
|
|
|
#if 1 /* #ifdef CONFIG_ARDUINO_DUE_REV3 works with REV2 as well */
|
|
|
|
/* This port was performed on the Arduino Due Rev 2 board.
|
|
* A NuttX user reported issues with the serial port on his Aduino Due Rev 3
|
|
* board.
|
|
* That problem was resolved as follows:
|
|
*
|
|
* "... The issue was in my hardware. I found the difference between Arduino
|
|
* Due shematics (revision R2) and actual PCB layout of my Arduino (revision
|
|
* R3). On a schematics which I download from arduino.cc was shown that 2nd
|
|
* pin of IC10 is connected to the ground, but on my Arduino the 2nd pin
|
|
* of IC10 was connected to its 1st pin instead of ground and in my case
|
|
* IC10 works in open-drain mode, but RX0 pin on SAM3x doesn't have pull-up
|
|
* and thus TX signal from AtMega16U2 can't reach the SAM3x input pin, on
|
|
* this pin always '0'.
|
|
*
|
|
* "My solution is to enable internal pull-up in SAM3x. ...
|
|
* Now shell console on UART0 (via USB programming connector) of Arduino Due
|
|
* Due works as expected."
|
|
*/
|
|
|
|
# undef GPIO_UART0_RXD
|
|
# define GPIO_UART0_RXD (GPIO_PERIPHA | GPIO_CFG_DEFAULT | GPIO_PORT_PIOA | \
|
|
GPIO_PIN8 | GPIO_CFG_PULLUP)
|
|
#endif
|
|
#endif /* __BOARDS_ARM_SAM34_ARDUINO_DUE_INCLUDE_BOARD_H */
|