182 lines
7.2 KiB
C
182 lines
7.2 KiB
C
/****************************************************************************
|
|
* boards/arm/lpc31xx/olimex-lpc-h3131/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
# include "lpc31_cgudrvr.h"
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* Frequency of the FFAST input */
|
|
|
|
#define BOARD_FREQIN_FFAST (12000000) /* ffast (12 MHz crystal) */
|
|
|
|
/* HPLL0 configuration */
|
|
|
|
#define BOARD_HPLL0_FINSEL CGU_HPFINSEL_FFAST /* Frequency input selection */
|
|
#define BOARD_HPLL0_NDEC 131 /* PLL N-divider value */
|
|
#define BOARD_HPLL0_MDEC 29784 /* PLL M-divider value */
|
|
#define BOARD_HPLL0_PDEC 7 /* PLL P-divider value */
|
|
#define BOARD_HPLL0_SELR 0 /* SELR bandwidth selection */
|
|
#define BOARD_HPLL0_SELI 8 /* SELI bandwidth selection */
|
|
#define BOARD_HPLL0_SELP 31 /* SELP bandwidth selection */
|
|
#define BOARD_HPLL0_MODE 0 /* PLL mode */
|
|
#define BOARD_HPLL0_FREQ 406425600 /* Frequency of the PLL in MHz */
|
|
|
|
/* HPLL1 configuration */
|
|
|
|
#define BOARD_HPLL1_FINSEL CGU_HPFINSEL_FFAST /* Frequency input selection */
|
|
#define BOARD_HPLL1_NDEC 770 /* PLL N-divider value */
|
|
#define BOARD_HPLL1_MDEC 8191 /* PLL M-divider value */
|
|
#define BOARD_HPLL1_PDEC 98 /* PLL P-divider value */
|
|
#define BOARD_HPLL1_SELR 0 /* SELR bandwidth selection */
|
|
#define BOARD_HPLL1_SELI 16 /* SELI bandwidth selection */
|
|
#define BOARD_HPLL1_SELP 8 /* SELP bandwidth selection */
|
|
#define BOARD_HPLL1_MODE 0 /* PLL mode */
|
|
#define BOARD_HPLL1_FREQ 180000000 /* Frequency of the PLL in MHz */
|
|
|
|
/* The following 3 bitsets determine which clocks will be enabled at
|
|
* initialization time.
|
|
*/
|
|
|
|
#define BOARD_CLKS_0_31 \
|
|
(_RBIT(CLKID_APB0CLK,0)|_RBIT(CLKID_APB1CLK,0)|_RBIT(CLKID_APB2CLK,0)|\
|
|
_RBIT(CLKID_APB3CLK,0)|_RBIT(CLKID_APB4CLK,0)|_RBIT(CLKID_AHB2INTCCLK,0)|\
|
|
_RBIT(CLKID_AHB0CLK,0)|_RBIT(CLKID_ARM926CORECLK,0)|_RBIT(CLKID_ARM926BUSIFCLK,0)|\
|
|
_RBIT(CLKID_ARM926RETIMECLK,0)|_RBIT(CLKID_ISRAM0CLK,0)|_RBIT(CLKID_ISRAM1CLK,0)|\
|
|
_RBIT(CLKID_ISROMCLK,0)|_RBIT(CLKID_INTCCLK,0)|_RBIT(CLKID_AHB2APB0PCLK,0)|\
|
|
_RBIT(CLKID_EVENTROUTERPCLK,0)|_RBIT(CLKID_CLOCKOUT,0))
|
|
|
|
#define BOARD_CLKS_32_63 \
|
|
(_RBIT(CLKID_IOCONFPCLK,32)|_RBIT(CLKID_CGUPCLK,32)|_RBIT(CLKID_SYSCREGPCLK,32)|\
|
|
_RBIT(CLKID_OTPPCLK,32)|_RBIT(CLKID_AHB2APB1PCLK,32)|_RBIT(CLKID_AHB2APB2PCLK,32)|\
|
|
_RBIT(CLKID_AHB2APB3PCLK,32)|_RBIT(CLKID_EDGEDETPCLK,32))
|
|
|
|
#define BOARD_CLKS_64_92 \
|
|
(0)
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
* any way. The following definitions are used to access individual LEDs.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0
|
|
#define BOARD_LED2 1
|
|
#define BOARD_NLEDS 2
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
|
|
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
* defined. In that case, the usage by the board port is as follows:
|
|
*
|
|
* SYMBOL Meaning LED state
|
|
* LED2 LED1
|
|
* ------------------------ -------------------------- ------ ------
|
|
*/
|
|
|
|
#define LED_STARTED 0 /* NuttX has been started OFF OFF */
|
|
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF */
|
|
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF */
|
|
#define LED_STACKCREATED 1 /* Idle stack created ON OFF */
|
|
#define LED_INIRQ 2 /* In an interrupt N/C N/C */
|
|
#define LED_SIGNAL 2 /* In a signal handler N/C N/C */
|
|
#define LED_ASSERTION 2 /* An assertion failed N/C N/C */
|
|
#define LED_PANIC 3 /* The system has crashed N/C Blinking */
|
|
#undef LED_IDLE /* MCU is is sleep mode Not used */
|
|
|
|
/* Thus if LED2 is statically on, NuttX has successfully booted and is,
|
|
* apparently, running normmally. If LED1 is flashing at approximately
|
|
* 2Hz, then a fatal error has been detected and the system has halted.
|
|
*
|
|
* NOTE: That LED2 is not used after completion of booting and may
|
|
* be used by other board-specific logic.
|
|
*/
|
|
|
|
/* Button definitions *******************************************************/
|
|
|
|
/* The Olimex LPC_H3131 has no user buttons */
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: lpc31_setup_overcurrent
|
|
*
|
|
* Description:
|
|
* Setup to receive an interrupt-level callback if an overcurrent condition
|
|
* is detected.
|
|
*
|
|
* Input Parameters:
|
|
* handler - New overcurrent interrupt handler
|
|
* arg - The argument that will accompany the interrupt
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) returned on success; a negated errno value is returned on
|
|
* failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#if 0 /* Not ready yet */
|
|
int lpc31_setup_overcurrent(xcpt_t handler, void *arg);
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_LPC31XX_OLIMEX_LPC_H3131_INCLUDE_BOARD_H */
|