5fe6ab5fc3
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5466 42af7a65-404d-4744-a932-0658087f49c3
63 lines
1.8 KiB
INI
Executable File
63 lines
1.8 KiB
INI
Executable File
# NXP LPC2148 ARM7TDMI
|
|
|
|
#daemon configuration
|
|
telnet_port 4444
|
|
gdb_port 3333
|
|
|
|
#interface
|
|
interface ft2232
|
|
ft2232_device_desc "Olimex OpenOCD JTAG A"
|
|
ft2232_layout "olimex-jtag"
|
|
ft2232_vid_pid 0x15BA 0x0003
|
|
|
|
# Use RCLK. If RCLK is not available fall back to 500kHz.
|
|
#
|
|
# Depending on cabling you might be able to eek this up to 2000kHz.
|
|
jtag_rclk 500
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME lpc2148
|
|
}
|
|
|
|
if { [info exists CPUTAPID ] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4f1f0f0f
|
|
}
|
|
|
|
adapter_nsrst_delay 200
|
|
jtag_ntrst_delay 200
|
|
|
|
# NOTE!!! LPCs need reset pulled while RTCK is low. 0 to activate
|
|
# JTAG, power-on reset is not enough, i.e. you need to perform a
|
|
# reset before being able to talk to the LPC2148, attach is not possible.
|
|
|
|
reset_config trst_and_srst
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME arm7tdmi -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Force target into ARM state
|
|
arm core_state arm
|
|
|
|
# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
|
|
# "User Flash Mode" where interrupt vectors are _not_ remapped,
|
|
# and reside in flash instead).
|
|
#
|
|
# See section 7.1 on page 32 ("Memory Mapping control register") in
|
|
# "UM10139: Volume 1: LPC214x User Manual", Rev. 02 -- 25 July 2006.
|
|
# http://www.standardics.nxp.com/support/documents/microcontrollers/pdf/user.manual.lpc2141.lpc2142.lpc2144.lpc2146.lpc2148.pdf
|
|
mwb 0xE01FC040 0x01
|
|
}
|
|
|
|
# flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME lpc2000 0x0 0x7d000 0 0 $_TARGETNAME lpc2000_v2 14765 calc_checksum
|