sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
60194f1efd
nuttx/configs/stm3240g-eval/nettest/defconfig
patacongo 60194f1efd Add logic to support the FSMC SRAM in the NuttX heap 
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4433 42af7a65-404d-4744-a932-0658087f49c3
2012-02-27 23:14:43 +00:00

1266 lines
46 KiB
Plaintext
Raw Blame History

############################################################################
# configs/stm3240g-eval/nettest/defconfig
#
# Copyright (C) 2011-2012 Gregory Nutt. All rights reserved.
# Author: Gregory Nutt <gnutt@nuttx.org>
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
#
# 1. Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in
# the documentation and/or other materials provided with the
# distribution.
# 3. Neither the name NuttX nor the names of its contributors may be
# used to endorse or promote products derived from this software
# without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSSIBILITY OF SUCH DAMAGE.
#
############################################################################
#
# architecture selection
#
# CONFIG_ARCH - identifies the arch subdirectory and, hence, the
# processor architecture.
# CONFIG_ARCH_family - for use in C code. This identifies the
# particular chip family that the architecture is implemented
# in.
# CONFIG_ARCH_architecture - for use in C code. This identifies the
# specific architecture within the chip familyl.
# CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
# CONFIG_ARCH_CHIP_name - For use in C code
# CONFIG_ARCH_BOARD - identifies the configs subdirectory and, hence,
# the board that supports the particular chip or SoC.
# CONFIG_ARCH_BOARD_name - for use in C code
# CONFIG_ENDIAN_BIG - define if big endian (default is little endian)
# CONFIG_BOARD_LOOPSPERMSEC - for delay loops
# CONFIG_DRAM_SIZE - Describes the installed DRAM.
# CONFIG_DRAM_START - The start address of DRAM (physical)
# CONFIG_DRAM_END - Last address+1 of installed RAM
# CONFIG_ARCH_IRQPRIO - The STM3240xxx supports interrupt prioritization
# CONFIG_ARCH_FPU - The STM3240xxx supports a floating point unit (FPU)
# (But, unfortunately, GCC does not support it).
# CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
# stack. If defined, this symbol is the size of the interrupt
# stack in bytes. If not defined, the user task stacks will be
# used during interrupt handling.
# CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
# CONFIG_ARCH_BOOTLOADER - Set if you are using a bootloader.
# CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
# CONFIG_ARCH_BUTTONS - Enable support for buttons. Unique to board architecture.
# CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
# cause a 100 second delay during boot-up. This 100 second delay
# serves no purpose other than it allows you to calibrate
# CONFIG_BOARD_LOOPSPERMSEC. You simply use a stop watch to measure
# the 100 second delay then adjust CONFIG_BOARD_LOOPSPERMSEC until
# the delay actually is 100 seconds.
# CONFIG_ARCH_DMA - Support DMA initialization
#
CONFIG_ARCH=arm
CONFIG_ARCH_ARM=y
CONFIG_ARCH_CORTEXM4=y
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_STM32F407IG=y
CONFIG_ARCH_BOARD=stm3240g-eval
CONFIG_ARCH_BOARD_STM3240G_EVAL=y
CONFIG_BOARD_LOOPSPERMSEC=16717
CONFIG_DRAM_SIZE=0x00030000
CONFIG_DRAM_START=0x20000000
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_FPU=n
CONFIG_ARCH_INTERRUPTSTACK=n
CONFIG_ARCH_STACKDUMP=y
CONFIG_ARCH_BOOTLOADER=n
CONFIG_ARCH_LEDS=y
CONFIG_ARCH_BUTTONS=n
CONFIG_ARCH_CALIBRATION=n
CONFIG_ARCH_DMA=n
#
# Identify toolchain and linker options
#
CONFIG_STM32_CODESOURCERYW=y
CONFIG_STM32_CODESOURCERYL=n
CONFIG_STM32_ATOLLIC_LITE=n
CONFIG_STM32_ATOLLIC_PRO=n
CONFIG_STM32_DEVKITARM=n
CONFIG_STM32_RAISONANCE=n
CONFIG_STM32_BUILDROOT=n
#
# JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):
#
# CONFIG_STM32_DFU - Use the DFU bootloader, not JTAG
#
# JTAG Enable options:
#
# CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
# CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
# but without JNTRST.
# CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
#
CONFIG_STM32_DFU=y
CONFIG_STM32_JTAG_FULL_ENABLE=y
CONFIG_STM32_JTAG_NOJNTRST_ENABLE=n
CONFIG_STM32_JTAG_SW_ENABLE=n
#
# On-chip TCM SRAM configuration
#
# CONFIG_STM32_TCMEXCLUDE - Exclude TCM SRAM from the HEAP. You would need
# to do this if DMA is enabled to prevent non-DMA-able TCM memory from
# being a part of the stack.
#
#
# On-board FSMC SRAM configuration
#
# CONFIG_STM32_FSMC - Required. See below
# CONFIG_MM_REGIONS - Required. Must be 2 or 3 (see above)
#
# CONFIG_STM32_FSMC_SRAM=y - Indicates that SRAM is available via the
# FSMC (as opposed to an LCD or FLASH).
# CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space
# CONFIG_HEAP2_END - The end (+1) of the SRAM in the FSMC address space
#
CONFIG_STM32_FSMC_SRAM=y
CONFIG_HEAP2_BASE=0x64000000
CONFIG_HEAP2_END=(0x64000000+(2*1024*1024))
#
# Individual subsystems can be enabled:
#
# Individual subsystems can be enabled:
# AHB1:
CONFIG_STM32_CRC=n
CONFIG_STM32_BKPSRAM=n
CONFIG_STM32_CCMDATARAM=n
CONFIG_STM32_DMA1=n
CONFIG_STM32_DMA2=n
CONFIG_STM32_ETHMAC=y
CONFIG_STM32_OTGHS=n
# AHB2:
CONFIG_STM32_DCMI=n
CONFIG_STM32_CRYP=n
CONFIG_STM32_HASH=n
CONFIG_STM32_RNG=n
CONFIG_STM32_OTGFS=n
# AHB3:
CONFIG_STM32_FSMC=n
# APB1:
CONFIG_STM32_TIM2=n
CONFIG_STM32_TIM3=n
CONFIG_STM32_TIM4=n
CONFIG_STM32_TIM5=n
CONFIG_STM32_TIM6=n
CONFIG_STM32_TIM7=n
CONFIG_STM32_TIM12=n
CONFIG_STM32_TIM13=n
CONFIG_STM32_TIM14=n
CONFIG_STM32_WWDG=n
CONFIG_STM32_SPI2=n
CONFIG_STM32_SPI3=n
CONFIG_STM32_USART2=n
CONFIG_STM32_USART3=y
CONFIG_STM32_UART4=n
CONFIG_STM32_UART5=n
CONFIG_STM32_I2C1=n
CONFIG_STM32_I2C2=n
CONFIG_STM32_I2C3=n
CONFIG_STM32_CAN1=n
CONFIG_STM32_CAN2=n
CONFIG_STM32_DAC=n
CONFIG_STM32_PWR=n
# APB2:
CONFIG_STM32_TIM1=n
CONFIG_STM32_TIM8=n
CONFIG_STM32_USART1=n
CONFIG_STM32_USART6=n
CONFIG_STM32_ADC1=n
CONFIG_STM32_ADC2=n
CONFIG_STM32_ADC3=n
CONFIG_STM32_SDIO=n
CONFIG_STM32_SPI1=n
CONFIG_STM32_SYSCFG=y
CONFIG_STM32_TIM9=n
CONFIG_STM32_TIM10=n
CONFIG_STM32_TIM11=n
#
# Timer and I2C devices may need to the following to force power to be applied:
#
#CONFIG_STM32_FORCEPOWER=y
#
# STM32F40xxx specific serial device driver settings
#
# CONFIG_USARTn_SERIAL_CONSOLE - selects the USARTn for the
# console and ttys0 (default is the USART1).
# CONFIG_USARTn_RXBUFSIZE - Characters are buffered as received.
# This specific the size of the receive buffer
# CONFIG_USARTn_TXBUFSIZE - Characters are buffered before
# being sent. This specific the size of the transmit buffer
# CONFIG_USARTn_BAUD - The configure BAUD of the UART. Must be
# CONFIG_USARTn_BITS - The number of bits. Must be either 7 or 8.
# CONFIG_USARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
# CONFIG_USARTn_2STOP - Two stop bits
#
CONFIG_USART1_SERIAL_CONSOLE=n
CONFIG_USART2_SERIAL_CONSOLE=n
CONFIG_USART3_SERIAL_CONSOLE=y
CONFIG_USART4_SERIAL_CONSOLE=n
CONFIG_USART5_SERIAL_CONSOLE=n
CONFIG_USART1_TXBUFSIZE=128
CONFIG_USART2_TXBUFSIZE=128
CONFIG_USART3_TXBUFSIZE=128
CONFIG_USART4_TXBUFSIZE=128
CONFIG_USART5_TXBUFSIZE=128
CONFIG_USART1_RXBUFSIZE=128
CONFIG_USART2_RXBUFSIZE=128
CONFIG_USART3_RXBUFSIZE=128
CONFIG_USART4_RXBUFSIZE=128
CONFIG_USART5_RXBUFSIZE=128
CONFIG_USART1_BAUD=115200
CONFIG_USART2_BAUD=115200
CONFIG_USART3_BAUD=115200
CONFIG_USART4_BAUD=115200
CONFIG_USART5_BAUD=115200
CONFIG_USART1_BITS=8
CONFIG_USART2_BITS=8
CONFIG_USART3_BITS=8
CONFIG_USART4_BITS=8
CONFIG_USART5_BITS=8
CONFIG_USART1_PARITY=0
CONFIG_USART2_PARITY=0
CONFIG_USART3_PARITY=0
CONFIG_USART4_PARITY=0
CONFIG_USART5_PARITY=0
CONFIG_USART1_2STOP=0
CONFIG_USART2_2STOP=0
CONFIG_USART3_2STOP=0
CONFIG_USART4_2STOP=0
CONFIG_USART5_2STOP=0
#
# STM32F40xxx specific SSI device driver settings
#
# CONFIG_SSIn_DISABLE - select to disable all support for
# the SSI
# CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support
# Poll-waiting is recommended if the interrupt rate would be to
# high in the interrupt driven case.
# CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
# emptying the Rx FIFO. If the SPI frequency is high and this
# value is large, then larger values of this setting may cause
# Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
#
CONFIG_SSI0_DISABLE=n
CONFIG_SSI1_DISABLE=y
CONFIG_SSI_POLLWAIT=y
#CONFIG_SSI_TXLIMIT=4
#
# STM32F40xxx specific CAN device driver settings
#
# CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
# CONFIG_STM32_CAN2 must also be defined)
# CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
# Standard 11-bit IDs.
# CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
# Default: 8
# CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
# Default: 4
# CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
# mode for testing. The STM32 CAN driver does support loopback mode.
# CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
# CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
#
CONFIG_CAN=n
CONFIG_CAN_EXTID=n
#CONFIG_CAN_FIFOSIZE
#CONFIG_CAN_NPENDINGRTR
CONFIG_CAN_LOOPBACK=n
CONFIG_CAN1_BAUD=700000
CONFIG_CAN2_BAUD=700000
#
# STM32F40xxx Ethernet device driver settings
#
# CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
# CONFIG_STM32_MII - Support Ethernet MII interface
# CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
# CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
# CONFIG_STM32_RMII - Support Ethernet RMII interface
# CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
# CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
# may be defined to select full duplex mode. Default: half-duplex
# CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
# may be defined to select 100 MBps speed. Default: 10 Mbps
# CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
# defined. The PHY status register address may diff from PHY to PHY. This
# configuration sets the address of the PHY status register.
# CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
# defined. This provides bit mask indicating 10 or 100MBps speed.
# CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
# defined. This provides the value of the speed bit(s) indicating 100MBps speed.
# CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
# defined. This provide bit mask indicating full or half duplex modes.
# CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
# defined. This provides the value of the mode bits indicating full duplex mode.
# CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported
# but some hooks are indicated with this condition.
# CONFIG_STM32_ETHMAC_REGDEBUG - If CONFIG_DEBUG is also enabled, this will
# generate far more debug output than you could ever care to see unless you
# are debugging low-level Ethernet driver features.
#
CONFIG_STM32_PHYADDR=0x01
CONFIG_STM32_MII=y
CONFIG_STM32_MII_MCO1=y
CONFIG_STM32_MII_MCO2=n
CONFIG_STM32_RMII=n
CONFIG_STM32_AUTONEG=y
#CONFIG_STM32_ETHFD
#CONFIG_STM32_ETH100MB
CONFIG_STM32_PHYSR=16
CONFIG_STM32_PHYSR_SPEED=0x0002
CONFIG_STM32_PHYSR_100MBPS=0x0000
CONFIG_STM32_PHYSR_MODE=0x0004
CONFIG_STM32_PHYSR_FULLDUPLEX=0x0004
CONFIG_STM32_ETH_PTP=n
CONFIG_STM32_ETHMAC_REGDEBUG=n
#
# I2C configuration
#
CONFIG_I2C=n
CONFIG_I2C_POLLED=y
CONFIG_I2C_TRANSFER=y
CONFIG_I2C_TRACE=n
#
# General build options
#
# CONFIG_RRLOAD_BINARY - make the rrload binary format used with
# BSPs from www.ridgerun.com using the tools/mkimage.sh script
# CONFIG_INTELHEX_BINARY - make the Intel HEX binary format
# used with many different loaders using the GNU objcopy program
# Should not be selected if you are not using the GNU toolchain.
# CONFIG_MOTOROLA_SREC - make the Motorola S-Record binary format
# used with many different loaders using the GNU objcopy program
# Should not be selected if you are not using the GNU toolchain.
# CONFIG_RAW_BINARY - make a raw binary format file used with many
# different loaders using the GNU objcopy program. This option
# should not be selected if you are not using the GNU toolchain.
# CONFIG_HAVE_LIBM - toolchain supports libm.a
#
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=y
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=n
CONFIG_HAVE_LIBM=n
#
# General OS setup
#
# CONFIG_APPS_DIR - Identifies the relative path to the directory
# that builds the application to link with NuttX. Default: ../apps
# CONFIG_DEBUG - enables built-in debug options
# CONFIG_DEBUG_VERBOSE - enables verbose debug output
# CONFIG_DEBUG_SYMBOLS - build without optimization and with
# debug symbols (needed for use with a debugger).
# CONFIG_HAVE_CXX - Enable support for C++S
# CONFIG_MM_REGIONS - If the architecture includes multiple
# regions of memory to allocate from, this specifies the
# number of memory regions that the memory manager must
# handle and enables the API mm_addregion(start, end);
# CONFIG_ARCH_LOWPUTC - architecture supports low-level, boot
# time console output
# CONFIG_MSEC_PER_TICK - The default system timer is 100Hz
# or MSEC_PER_TICK=10. This setting may be defined to
# inform NuttX that the processor hardware is providing
# system timer interrupts at some interrupt interval other
# than 10 msec.
# CONFIG_RR_INTERVAL - The round robin timeslice will be set
# this number of milliseconds; Round robin scheduling can
# be disabled by setting this value to zero.
# CONFIG_SCHED_INSTRUMENTATION - enables instrumentation in
# scheduler to monitor system performance
# CONFIG_TASK_NAME_SIZE - Spcifies that maximum size of a
# task name to save in the TCB. Useful if scheduler
# instrumentation is selected. Set to zero to disable.
# CONFIG_START_YEAR, CONFIG_START_MONTH, CONFIG_START_DAY -
# Used to initialize the internal time logic.
# CONFIG_GREGORIAN_TIME - Enables Gregorian time conversions.
# You would only need this if you are concerned about accurate
# time conversions in the past or in the distant future.
# CONFIG_JULIAN_TIME - Enables Julian time conversions. You
# would only need this if you are concerned about accurate
# time conversion in the distand past. You must also define
# CONFIG_GREGORIAN_TIME in order to use Julian time.
# CONFIG_DEV_CONSOLE - Set if architecture-specific logic
# provides /dev/console. Enables stdout, stderr, stdin.
# CONFIG_DEV_LOWCONSOLE - Use the simple, low-level serial console
# driver (minimul support)
# CONFIG_MUTEX_TYPES: Set to enable support for recursive and
# errorcheck mutexes. Enables pthread_mutexattr_settype().
# CONFIG_PRIORITY_INHERITANCE : Set to enable support for priority
# inheritance on mutexes and semaphores.
# CONFIG_SEM_PREALLOCHOLDERS: This setting is only used if priority
# inheritance is enabled. It defines the maximum number of
# different threads (minus one) that can take counts on a
# semaphore with priority inheritance support. This may be
# set to zero if priority inheritance is disabled OR if you
# are only using semaphores as mutexes (only one holder) OR
# if no more than two threads participate using a counting
# semaphore.
# CONFIG_SEM_NNESTPRIO. If priority inheritance is enabled,
# then this setting is the maximum number of higher priority
# threads (minus 1) than can be waiting for another thread
# to release a count on a semaphore. This value may be set
# to zero if no more than one thread is expected to wait for
# a semaphore.
# CONFIG_FDCLONE_DISABLE. Disable cloning of all file descriptors
# by task_create() when a new task is started. If set, all
# files/drivers will appear to be closed in the new task.
# CONFIG_FDCLONE_STDIO. Disable cloning of all but the first
# three file descriptors (stdin, stdout, stderr) by task_create()
# when a new task is started. If set, all files/drivers will
# appear to be closed in the new task except for stdin, stdout,
# and stderr.
# CONFIG_SDCLONE_DISABLE. Disable cloning of all socket
# desciptors by task_create() when a new task is started. If
# set, all sockets will appear to be closed in the new task.
# CONFIG_SCHED_WORKQUEUE. Create a dedicated "worker" thread to
# handle delayed processing from interrupt handlers. This feature
# is required for some drivers but, if there are not complaints,
# can be safely disabled. The worker thread also performs
# garbage collection -- completing any delayed memory deallocations
# from interrupt handlers. If the worker thread is disabled,
# then that clean will be performed by the IDLE thread instead
# (which runs at the lowest of priority and may not be appropriate
# if memory reclamation is of high priority). If CONFIG_SCHED_WORKQUEUE
# is enabled, then the following options can also be used:
# CONFIG_SCHED_WORKPRIORITY - The execution priority of the worker
# thread. Default: 50
# CONFIG_SCHED_WORKPERIOD - How often the worker thread checks for
# work in units of microseconds. Default: 50*1000 (50 MS).
# CONFIG_SCHED_WORKSTACKSIZE - The stack size allocated for the worker
# thread. Default: CONFIG_IDLETHREAD_STACKSIZE.
# CONFIG_SIG_SIGWORK - The signal number that will be used to wake-up
# the worker thread. Default: 4
# CONFIG_SCHED_WAITPID - Enable the waitpid() API
# CONFIG_SCHED_ATEXIT - Enabled the atexit() API
#
#CONFIG_APPS_DIR=
CONFIG_DEBUG=n
CONFIG_DEBUG_VERBOSE=n
CONFIG_DEBUG_SYMBOLS=n
CONFIG_DEBUG_NET=n
CONFIG_HAVE_CXX=y
CONFIG_MM_REGIONS=2
CONFIG_ARCH_LOWPUTC=y
CONFIG_RR_INTERVAL=200
CONFIG_SCHED_INSTRUMENTATION=n
CONFIG_TASK_NAME_SIZE=0
CONFIG_START_YEAR=2011
CONFIG_START_MONTH=12
CONFIG_START_DAY=6
CONFIG_GREGORIAN_TIME=n
CONFIG_JULIAN_TIME=n
CONFIG_DEV_CONSOLE=y
CONFIG_DEV_LOWCONSOLE=y
CONFIG_MUTEX_TYPES=n
CONFIG_PRIORITY_INHERITANCE=n
CONFIG_SEM_PREALLOCHOLDERS=0
CONFIG_SEM_NNESTPRIO=0
CONFIG_FDCLONE_DISABLE=n
CONFIG_FDCLONE_STDIO=n
CONFIG_SDCLONE_DISABLE=y
CONFIG_SCHED_WORKQUEUE=n
CONFIG_SCHED_WORKPRIORITY=50
CONFIG_SCHED_WORKPERIOD=(50*1000)
CONFIG_SCHED_WORKSTACKSIZE=1024
CONFIG_SIG_SIGWORK=4
CONFIG_SCHED_WAITPID=y
CONFIG_SCHED_ATEXIT=n
#
# Settings for NXFLAT
#
# CONFIG_NXFLAT. Enable support for the NXFLAT binary format.
# This format will support execution of NuttX binaries located
# in a ROMFS filesystem (see examples/nxflat).
# CONFIG_NXFLAT_DUMPBUFFER. Dump a most buffers that NXFFLAT deals
# with. CONFIG_DEBUG, CONFIG_DEBUG_VERBOSE, and
# CONFIG_DEBUG_BINFMT have to be defined or
# CONFIG_NXFLAT_DUMPBUFFER does nothing.
# CONFIG_SYMTAB_ORDEREDBYNAME. Select if the system symbol table
# is ordered by symbol name
#
CONFIG_NXFLAT=n
CONFIG_NXFLAT_DUMPBUFFER=n
CONFIG_SYMTAB_ORDEREDBYNAME=y
#
# The following can be used to disable categories of
# APIs supported by the OS. If the compiler supports
# weak functions, then it should not be necessary to
# disable functions unless you want to restrict usage
# of those APIs.
#
# There are certain dependency relationships in these
# features.
#
# o mq_notify logic depends on signals to awaken tasks
# waiting for queues to become full or empty.
# o pthread_condtimedwait() depends on signals to wake
# up waiting tasks.
#
CONFIG_DISABLE_CLOCK=n
CONFIG_DISABLE_POSIX_TIMERS=n
CONFIG_DISABLE_PTHREAD=y
CONFIG_DISABLE_SIGNALS=n
CONFIG_DISABLE_MQUEUE=y
CONFIG_DISABLE_MOUNTPOINT=y
CONFIG_DISABLE_ENVIRON=y
CONFIG_DISABLE_POLL=y
#
# Misc libc settings
#
# CONFIG_NOPRINTF_FIELDWIDTH - sprintf-related logic is a
# little smaller if we do not support fieldwidthes
#
CONFIG_NOPRINTF_FIELDWIDTH=n
#
# Allow for architecture optimized implementations
#
# The architecture can provide optimized versions of the
# following to improve system performance
#
CONFIG_ARCH_MEMCPY=n
CONFIG_ARCH_MEMCMP=n
CONFIG_ARCH_MEMMOVE=n
CONFIG_ARCH_MEMSET=n
CONFIG_ARCH_STRCMP=n
CONFIG_ARCH_STRCPY=n
CONFIG_ARCH_STRNCPY=n
CONFIG_ARCH_STRLEN=n
CONFIG_ARCH_STRNLEN=n
CONFIG_ARCH_BZERO=n
#
# Sizes of configurable things (0 disables)
#
# CONFIG_MAX_TASKS - The maximum number of simultaneously
# active tasks. This value must be a power of two.
# CONFIG_MAX_TASK_ARGS - This controls the maximum number of
# of parameters that a task may receive (i.e., maxmum value
# of 'argc')
# CONFIG_NPTHREAD_KEYS - The number of items of thread-
# specific data that can be retained
# CONFIG_NFILE_DESCRIPTORS - The maximum number of file
# descriptors (one for each open)
# CONFIG_NFILE_STREAMS - The maximum number of streams that
# can be fopen'ed
# CONFIG_NAME_MAX - The maximum size of a file name.
# CONFIG_STDIO_BUFFER_SIZE - Size of the buffer to allocate
# on fopen. (Only if CONFIG_NFILE_STREAMS > 0)
# CONFIG_STDIO_LINEBUFFER - If standard C buffered I/O is enabled
# (CONFIG_STDIO_BUFFER_SIZE > 0), then this option may be added
# to force automatic, line-oriented flushing the output buffer
# for putc(), fputc(), putchar(), puts(), fputs(), printf(),
# fprintf(), and vfprintf(). When a newline is encountered in
# the output string, the output buffer will be flushed. This
# (slightly) increases the NuttX footprint but supports the kind
# of behavior that people expect for printf().
# CONFIG_NUNGET_CHARS - Number of characters that can be
# buffered by ungetc() (Only if CONFIG_NFILE_STREAMS > 0)
# CONFIG_PREALLOC_MQ_MSGS - The number of pre-allocated message
# structures. The system manages a pool of preallocated
# message structures to minimize dynamic allocations
# CONFIG_MQ_MAXMSGSIZE - Message structures are allocated with
# a fixed payload size given by this settin (does not include
# other message structure overhead.
# CONFIG_MAX_WDOGPARMS - Maximum number of parameters that
# can be passed to a watchdog handler
# CONFIG_PREALLOC_WDOGS - The number of pre-allocated watchdog
# structures. The system manages a pool of preallocated
# watchdog structures to minimize dynamic allocations
# CONFIG_PREALLOC_TIMERS - The number of pre-allocated POSIX
# timer structures. The system manages a pool of preallocated
# timer structures to minimize dynamic allocations. Set to
# zero for all dynamic allocations.
#
CONFIG_MAX_TASKS=8
CONFIG_MAX_TASK_ARGS=4
CONFIG_NPTHREAD_KEYS=0
CONFIG_NFILE_DESCRIPTORS=8
CONFIG_NFILE_STREAMS=8
CONFIG_NAME_MAX=32
CONFIG_STDIO_BUFFER_SIZE=0
CONFIG_STDIO_LINEBUFFER=y
CONFIG_NUNGET_CHARS=0
CONFIG_PREALLOC_MQ_MSGS=0
CONFIG_MQ_MAXMSGSIZE=0
CONFIG_MAX_WDOGPARMS=4
CONFIG_PREALLOC_WDOGS=8
CONFIG_PREALLOC_TIMERS=8
#
# Framebuffer driver options
#
CONFIG_FB_CMAP=n
CONFIG_FB_HWCURSOR=n
CONFIG_FB_HWCURSORIMAGE=n
#CONFIG_FB_HWCURSORSIZE
#CONFIG_FB_TRANSPARENCY
#
# Filesystem configuration
#
# CONFIG_FS_FAT - Enable FAT filesystem support
# CONFIG_FAT_SECTORSIZE - Max supported sector size
# CONFIG_FAT_LCNAMES - Enable use of the NT-style upper/lower case 8.3
# file name support.
# CONFIG_FAT_LFN - Enable FAT long file names. NOTE: Microsoft claims
# patents on FAT long file name technology. Please read the
# disclaimer in the top-level COPYING file and only enable this
# feature if you understand these issues.
# CONFIG_FAT_MAXFNAME - If CONFIG_FAT_LFN is defined, then the
# default, maximum long file name is 255 bytes. This can eat up
# a lot of memory (especially stack space). If you are willing
# to live with some non-standard, short long file names, then
# define this value. A good choice would be the same value as
# selected for CONFIG_NAME_MAX which will limit the visibility
# of longer file names anyway.
# CONFIG_FS_NXFFS: Enable NuttX FLASH file system (NXFF) support.
# CONFIG_NXFFS_ERASEDSTATE: The erased state of FLASH.
# This must have one of the values of 0xff or 0x00.
# Default: 0xff.
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
# don't both with file chunks smaller than this number of data bytes.
# CONFIG_NXFFS_MAXNAMLEN: The maximum size of an NXFFS file name.
# Default: 255.
# CONFIG_NXFFS_PACKTHRESHOLD: When packing flash file data,
# don't both with file chunks smaller than this number of data bytes.
# Default: 32.
# CONFIG_NXFFS_TAILTHRESHOLD: clean-up can either mean
# packing files together toward the end of the file or, if file are
# deleted at the end of the file, clean up can simply mean erasing
# the end of FLASH memory so that it can be re-used again. However,
# doing this can also harm the life of the FLASH part because it can
# mean that the tail end of the FLASH is re-used too often. This
# threshold determines if/when it is worth erased the tail end of FLASH
# and making it available for re-use (and possible over-wear).
# Default: 8192.
# CONFIG_FS_ROMFS - Enable ROMFS filesystem support
# CONFIG_FS_RAMMAP - For file systems that do not support XIP, this
# option will enable a limited form of memory mapping that is
# implemented by copying whole files into memory.
#
CONFIG_FS_FAT=n
CONFIG_FAT_LCNAMES=y
CONFIG_FAT_LFN=y
CONFIG_FAT_MAXFNAME=32
CONFIG_FS_NXFFS=n
CONFIG_FS_ROMFS=n
#
# SPI-based MMC/SD driver
#
# CONFIG_MMCSD_NSLOTS
# Number of MMC/SD slots supported by the driver
# CONFIG_MMCSD_READONLY
# Provide read-only access (default is read/write)
# CONFIG_MMCSD_SPICLOCK - Maximum SPI clock to drive MMC/SD card.
# Default is 20MHz.
#
CONFIG_MMCSD_NSLOTS=1
CONFIG_MMCSD_READONLY=n
CONFIG_MMCSD_SPICLOCK=12500000
#
# Block driver buffering
#
# CONFIG_FS_READAHEAD
# Enable read-ahead buffering
# CONFIG_FS_WRITEBUFFER
# Enable write buffering
#
CONFIG_FS_READAHEAD=n
CONFIG_FS_WRITEBUFFER=n
#
# STM32 SDIO-based MMC/SD driver
#
# CONFIG_SDIO_DMA
# SDIO driver supports DMA
# CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
# CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
# Default: Medium
# CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
# 4-bit transfer mode.
# CONFIG_MMCSD_MULTIBLOCK_DISABLE - Use only the single block transfer method.
# This setting is used to work around buggy drivers that cannot handle
# multiple block transfers.
# CONFIG_MMCSD_MMCSUPPORT
# Enable support for MMC cards
# CONFIG_MMCSD_HAVECARDDETECT
# SDIO driver card detection is 100% accurate
#
CONFIG_SDIO_DMA=n
#CONFIG_SDIO_PRI=128
#CONFIG_SDIO_DMAPRIO
#CONFIG_SDIO_WIDTH_D1_ONLY
CONFIG_MMCSD_MULTIBLOCK_DISABLE=y
CONFIG_MMCSD_MMCSUPPORT=n
CONFIG_MMCSD_HAVECARDDETECT=n
#
# TCP/IP and UDP support via uIP
#
# CONFIG_NET - Enable or disable all network features
# CONFIG_NET_NOINTS - uIP not called from interrupt level.
# CONFIG_NET_MULTIBUFFER - Use multiple input/output buffers (probably no)
# CONFIG_NET_IPv6 - Build in support for IPv6
# CONFIG_NSOCKET_DESCRIPTORS - Maximum number of socket descriptors per task/thread.
# CONFIG_NET_SOCKOPTS - Enable or disable support for socket options
# CONFIG_NET_BUFSIZE - uIP buffer size
# CONFIG_NET_TCP - TCP support on or off
# CONFIG_NET_TCP_CONNS - Maximum number of TCP connections (all tasks)
# CONFIG_NET_TCP_READAHEAD_BUFSIZE - Size of TCP read-ahead buffers
# CONFIG_NET_NTCP_READAHEAD_BUFFERS - Number of TCP read-ahead buffers (may be zero)
# CONFIG_NET_TCPBACKLOG - Incoming connections pend in a backlog until
# accept() is called. The size of the backlog is selected when listen() is called.
# CONFIG_NET_MAX_LISTENPORTS - Maximum number of listening TCP ports (all tasks)
# CONFIG_NET_UDP - UDP support on or off
# CONFIG_NET_UDP_CHECKSUMS - UDP checksums on or off
# CONFIG_NET_UDP_CONNS - The maximum amount of concurrent UDP connections
# CONFIG_NET_ICMP - ICMP ping response support on or off
# CONFIG_NET_ICMP_PING - ICMP ping request support on or off
# CONFIG_NET_PINGADDRCONF - Use "ping" packet for setting IP address
# CONFIG_NET_STATISTICS - uIP statistics on or off
# CONFIG_NET_RECEIVE_WINDOW - The size of the advertised receiver's window
# CONFIG_NET_BROADCAST - Broadcast support
# CONFIG_NET_ARPTAB_SIZE - The size of the ARP table
# CONFIG_NET_ARP_IPIN - Harvest IP/MAC address mappings from the ARP table
# from incoming IP packets.
# CONFIG_NET_MULTICAST - Outgoing multi-cast address support
# CONFIG_NET_FWCACHE_SIZE - number of packets to remember when
# looking for duplicates
#
CONFIG_NET=y
CONFIG_NET_NOINTS=n
CONFIG_NET_MULTIBUFFER=y
CONFIG_NET_IPv6=n
CONFIG_NSOCKET_DESCRIPTORS=10
CONFIG_NET_SOCKOPTS=y
CONFIG_NET_BUFSIZE=420
CONFIG_NET_TCP=y
CONFIG_NET_TCP_CONNS=40
#CONFIG_NET_TCP_READAHEAD_BUFSIZE
CONFIG_NET_NTCP_READAHEAD_BUFFERS=8
CONFIG_NET_TCPBACKLOG=n
CONFIG_NET_MAX_LISTENPORTS=40
CONFIG_NET_UDP=n
CONFIG_NET_UDP_CHECKSUMS=y
#CONFIG_NET_UDP_CONNS=10
CONFIG_NET_ICMP=y
CONFIG_NET_ICMP_PING=n
#CONFIG_NET_PINGADDRCONF=0
CONFIG_NET_STATISTICS=n
#CONFIG_NET_RECEIVE_WINDOW=
CONFIG_NET_BROADCAST=n
#CONFIG_NET_ARPTAB_SIZE=8
CONFIG_NET_ARP_IPIN=n
CONFIG_NET_MULTICAST=n
#CONFIG_NET_FWCACHE_SIZE=2
#
# UIP Network Utilities
# CONFIG_NET_DHCP_LIGHT - Reduces size of DHCP
# CONFIG_NET_RESOLV_ENTRIES - Number of resolver entries
#
CONFIG_NET_DHCP_LIGHT=n
CONFIG_NET_RESOLV_ENTRIES=4
#
# RTC Configuration
#
# CONFIG_RTC - Enables general support for a hardware RTC. Specific
# architectures may require other specific settings.
# CONFIG_RTC_DATETIME - There are two general types of RTC: (1) A simple
# battery backed counter that keeps the time when power is down, and (2)
# A full date / time RTC the provides the date and time information, often
# in BCD format. If CONFIG_RTC_DATETIME is selected, it specifies this
# second kind of RTC. In this case, the RTC is used to "seed" the normal
# NuttX timer and the NuttX system timer provides for higher resoution
# time.
# CONFIG_RTC_HIRES - If CONFIG_RTC_DATETIME not selected, then the simple,
# battery backed counter is used. There are two different implementations
# of such simple counters based on the time resolution of the counter:
# The typical RTC keeps time to resolution of 1 second, usually
# supporting a 32-bit time_t value. In this case, the RTC is used to
# "seed" the normal NuttX timer and the NuttX timer provides for higher
# resoution time. If CONFIG_RTC_HIRES is enabled in the NuttX configuration,
# then the RTC provides higher resolution time and completely replaces the
# system timer for purpose of date and time.
# CONFIG_RTC_FREQUENCY - If CONFIG_RTC_HIRES is defined, then the frequency
# of the high resolution RTC must be provided. If CONFIG_RTC_HIRES is
# not defined, CONFIG_RTC_FREQUENCY is assumed to be one.
# CONFIG_RTC_ALARM - Enable if the RTC hardware supports setting of an
# alarm. A callback function will be executed when the alarm goes off
#
CONFIG_RTC=n
CONFIG_RTC_DATETIME=y
CONFIG_RTC_HIRES=n
CONFIG_RTC_FREQUENCY=n
CONFIG_RTC_ALARM=n
#
# USB Device Configuration
#
# CONFIG_USBDEV
# Enables USB device support
# CONFIG_USBDEV_ISOCHRONOUS
# Build in extra support for isochronous endpoints
# CONFIG_USBDEV_DUALSPEED
# Hardware handles high and full speed operation (USB 2.0)
# CONFIG_USBDEV_SELFPOWERED
# Will cause USB features to indicate that the device is
# self-powered
# CONFIG_USBDEV_MAXPOWER
# Maximum power consumption in mA
# CONFIG_USBDEV_TRACE
# Enables USB tracing for debug
# CONFIG_USBDEV_TRACE_NRECORDS
# Number of trace entries to remember
#
CONFIG_USBDEV=n
CONFIG_USBDEV_ISOCHRONOUS=n
CONFIG_USBDEV_DUALSPEED=n
CONFIG_USBDEV_SELFPOWERED=y
CONFIG_USBDEV_REMOTEWAKEUP=n
CONFIG_USBDEV_MAXPOWER=100
CONFIG_USBDEV_TRACE=n
CONFIG_USBDEV_TRACE_NRECORDS=128
#
# USB Serial Device Configuration
#
# CONFIG_PL2303
# Enable compilation of the USB serial driver
# CONFIG_PL2303_EPINTIN
# The logical 7-bit address of a hardware endpoint that supports
# interrupt IN operation
# CONFIG_PL2303_EPBULKOUT
# The logical 7-bit address of a hardware endpoint that supports
# bulk OUT operation
# CONFIG_PL2303_EPBULKIN
# The logical 7-bit address of a hardware endpoint that supports
# bulk IN operation
# # CONFIG_PL2303_NWRREQS and CONFIG_PL2303_NRDREQS
# The number of write/read requests that can be in flight
# CONFIG_PL2303_VENDORID and CONFIG_PL2303_VENDORSTR
# The vendor ID code/string
# CONFIG_PL2303_PRODUCTID and CONFIG_PL2303_PRODUCTSTR
# The product ID code/string
# CONFIG_PL2303_RXBUFSIZE and CONFIG_PL2303_TXBUFSIZE
# Size of the serial receive/transmit buffers
#
CONFIG_PL2303=n
CONFIG_PL2303_EPINTIN=1
CONFIG_PL2303_EPBULKOUT=2
CONFIG_PL2303_EPBULKIN=3
CONFIG_PL2303_NWRREQS=4
CONFIG_PL2303_NRDREQS=4
CONFIG_PL2303_VENDORID=0x067b
CONFIG_PL2303_PRODUCTID=0x2303
CONFIG_PL2303_VENDORSTR="Nuttx"
CONFIG_PL2303_PRODUCTSTR="USBdev Serial"
CONFIG_PL2303_RXBUFSIZE=512
CONFIG_PL2303_TXBUFSIZE=512
#
# USB Storage Device Configuration
#
# CONFIG_USBMSC
# Enable compilation of the USB storage driver
# CONFIG_USBMSC_EP0MAXPACKET
# Max packet size for endpoint 0
# CONFIG_USBMSC_EPBULKOUT and CONFIG_USBMSC_EPBULKIN
# The logical 7-bit address of a hardware endpoints that support
# bulk OUT and IN operations
# CONFIG_USBMSC_NWRREQS and CONFIG_USBMSC_NRDREQS
# The number of write/read requests that can be in flight
# CONFIG_USBMSC_BULKINREQLEN and CONFIG_USBMSC_BULKOUTREQLEN
# The size of the buffer in each write/read request. This
# value needs to be at least as large as the endpoint
# maxpacket and ideally as large as a block device sector.
# CONFIG_USBMSC_VENDORID and CONFIG_USBMSC_VENDORSTR
# The vendor ID code/string
# CONFIG_USBMSC_PRODUCTID and CONFIG_USBMSC_PRODUCTSTR
# The product ID code/string
# CONFIG_USBMSC_REMOVABLE
# Select if the media is removable
#
CONFIG_USBMSC=n
CONFIG_USBMSC_EP0MAXPACKET=64
CONFIG_USBMSC_EPBULKOUT=2
CONFIG_USBMSC_EPBULKIN=5
CONFIG_USBMSC_NRDREQS=2
CONFIG_USBMSC_NWRREQS=2
CONFIG_USBMSC_BULKINREQLEN=256
CONFIG_USBMSC_BULKOUTREQLEN=256
CONFIG_USBMSC_VENDORID=0x584e
CONFIG_USBMSC_VENDORSTR="NuttX"
CONFIG_USBMSC_PRODUCTID=0x5342
CONFIG_USBMSC_PRODUCTSTR="USBdev Storage"
CONFIG_USBMSC_VERSIONNO=0x0399
CONFIG_USBMSC_REMOVABLE=y
#
# Graphics related configuration settings
#
# CONFIG_NX
# Enables overall support for graphics library and NX
# CONFIG_NX_MULTIUSER
# Configures NX in multi-user mode
# CONFIG_NX_NPLANES
# Some YUV color formats requires support for multiple planes,
# one for each color component. Unless you have such special
# hardware, this value should be undefined or set to 1
# CONFIG_NX_DISABLE_1BPP, CONFIG_NX_DISABLE_2BPP,
# CONFIG_NX_DISABLE_4BPP, CONFIG_NX_DISABLE_8BPP,
# CONFIG_NX_DISABLE_16BPP, CONFIG_NX_DISABLE_24BPP, and
# CONFIG_NX_DISABLE_32BPP
# NX supports a variety of pixel depths. You can save some
# memory by disabling support for unused color depths.
# CONFIG_NX_PACKEDMSFIRST
# If a pixel depth of less than 8-bits is used, then NX needs
# to know if the pixels pack from the MS to LS or from LS to MS
# CONFIG_NX_LCDDRIVER
# By default, NX builds to use a framebuffer driver (see
# include/nuttx/fb.h). If this option is defined, NX will
# build to use an LCD driver (see include/nuttx/lcd/lcd.h).
# CONFIG_LCD_MAXPOWER - The full-on power setting for an LCD device.
# CONFIG_LCD_MAXCONTRAST - The maximum contrast value for an LCD device.
# CONFIG_NX_MOUSE
# Build in support for mouse input
# CONFIG_NX_KBD
# Build in support of keypad/keyboard input
# CONFIG_NXTK_BORDERWIDTH
# Specifies with with of the border (in pixels) used with
# framed windows. The default is 4.
# CONFIG_NXTK_BORDERCOLOR1 and CONFIG_NXTK_BORDERCOLOR2
# Specify the colors of the border used with framed windows.
# CONFIG_NXTK_BORDERCOLOR2 is the shadow side color and so
# is normally darker. The default is medium and dark grey,
# respectively
# CONFIG_NXTK_AUTORAISE
# If set, a window will be raised to the top if the mouse position
# is over a visible portion of the window. Default: A mouse
# button must be clicked over a visible portion of the window.
# CONFIG_NXFONTS_CHARBITS
# The number of bits in the character set. Current options are
# only 7 and 8. The default is 7.
# CONFIG_NXFONT_SANS17X22
# This option enables support for a tiny, 17x22 san serif font
# (font ID FONTID_SANS17X22 == 14).
# CONFIG_NXFONT_SANS20X26
# This option enables support for a tiny, 20x26 san serif font
# (font ID FONTID_SANS20X26 == 15).
# CONFIG_NXFONT_SANS23X27
# This option enables support for a tiny, 23x27 san serif font
# (font ID FONTID_SANS23X27 == 1).
# CONFIG_NXFONT_SANS22X29
# This option enables support for a small, 22x29 san serif font
# (font ID FONTID_SANS22X29 == 2).
# CONFIG_NXFONT_SANS28X37
# This option enables support for a medium, 28x37 san serif font
# (font ID FONTID_SANS28X37 == 3).
# CONFIG_NXFONT_SANS39X48
# This option enables support for a large, 39x48 san serif font
# (font ID FONTID_SANS39X48 == 4).
# CONFIG_NXFONT_SANS17X23B
# This option enables support for a tiny, 17x23 san serif bold font
# (font ID FONTID_SANS17X23B == 16).
# CONFIG_NXFONT_SANS20X27B
# This option enables support for a tiny, 20x27 san serif bold font
# (font ID FONTID_SANS20X27B == 17).
# CONFIG_NXFONT_SANS22X29B
# This option enables support for a small, 22x29 san serif bold font
# (font ID FONTID_SANS22X29B == 5).
# CONFIG_NXFONT_SANS28X37B
# This option enables support for a medium, 28x37 san serif bold font
# (font ID FONTID_SANS28X37B == 6).
# CONFIG_NXFONT_SANS40X49B
# This option enables support for a large, 40x49 san serif bold font
# (font ID FONTID_SANS40X49B == 7).
# CONFIG_NXFONT_SERIF22X29
# This option enables support for a small, 22x29 font (with serifs)
# (font ID FONTID_SERIF22X29 == 8).
# CONFIG_NXFONT_SERIF29X37
# This option enables support for a medium, 29x37 font (with serifs)
# (font ID FONTID_SERIF29X37 == 9).
# CONFIG_NXFONT_SERIF38X48
# This option enables support for a large, 38x48 font (with serifs)
# (font ID FONTID_SERIF38X48 == 10).
# CONFIG_NXFONT_SERIF22X28B
# This option enables support for a small, 27x38 bold font (with serifs)
# (font ID FONTID_SERIF22X28B == 11).
# CONFIG_NXFONT_SERIF27X38B
# This option enables support for a medium, 27x38 bold font (with serifs)
# (font ID FONTID_SERIF27X38B == 12).
# CONFIG_NXFONT_SERIF38X49B
# This option enables support for a large, 38x49 bold font (with serifs)
# (font ID FONTID_SERIF38X49B == 13).
#
# NX Multi-user only options:
#
# CONFIG_NX_BLOCKING
# Open the client message queues in blocking mode. In this case,
# nx_eventhandler() will not return until a message is received and processed.
# CONFIG_NX_MXSERVERMSGS and CONFIG_NX_MXCLIENTMSGS
# Specifies the maximum number of messages that can fit in
# the message queues. No additional resources are allocated, but
# this can be set to prevent flooding of the client or server with
# too many messages (CONFIG_PREALLOC_MQ_MSGS controls how many
# messages are pre-allocated).
#
CONFIG_NX=n
CONFIG_NX_MULTIUSER=n
CONFIG_NX_NPLANES=1
CONFIG_NX_DISABLE_1BPP=y
CONFIG_NX_DISABLE_2BPP=y
CONFIG_NX_DISABLE_4BPP=y
CONFIG_NX_DISABLE_8BPP=y
CONFIG_NX_DISABLE_16BPP=n
CONFIG_NX_DISABLE_24BPP=y
CONFIG_NX_DISABLE_32BPP=y
CONFIG_NX_PACKEDMSFIRST=n
CONFIG_NX_LCDDRIVER=y
CONFIG_LCD_MAXPOWER=1
CONFIG_LCD_MAXCONTRAST=1
CONFIG_NX_MOUSE=y
CONFIG_NX_KBD=y
#CONFIG_NXTK_BORDERWIDTH=4
CONFIG_NXTK_BORDERCOLOR1=0xd69a
CONFIG_NXTK_BORDERCOLOR2=0xad55
CONFIG_NXTK_AUTORAISE=n
CONFIG_NXFONT_SANS17X22=y
CONFIG_NXFONT_SANS20X26=n
CONFIG_NXFONT_SANS22X29=n
CONFIG_NXFONT_SANS23X27=n
CONFIG_NXFONT_SANS28X37=n
CONFIG_NXFONT_SANS17X23B=n
CONFIG_NXFONT_SANS20X27B=y
CONFIG_NXFONT_SANS22X29B=y
CONFIG_NXFONT_SANS28X37B=n
CONFIG_NXFONT_SANS40X49B=n
CONFIG_NXFONT_SERIF22X29=n
CONFIG_NXFONT_SERIF29X37=n
CONFIG_NXFONT_SERIF38X48=n
CONFIG_NXFONT_SERIF22X28B=n
CONFIG_NXFONT_SERIF27X38B=n
CONFIG_NXFONT_SERIF38X49B=n
CONFIG_NXFONTS_CHARBITS=7
CONFIG_NX_BLOCKING=y
CONFIG_NX_MXSERVERMSGS=32
CONFIG_NX_MXCLIENTMSGS=16
#
# Settings for examples/uip
#
CONFIG_EXAMPLE_UIP_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_EXAMPLE_UIP_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_EXAMPLE_UIP_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_EXAMPLE_UIP_DHCPC=n
#
# Settings for examples/nettest
#
CONFIG_EXAMPLE_NETTEST_SERVER=n
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=y
CONFIG_EXAMPLE_NETTEST_NOMAC=y
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_EXAMPLE_NETTEST_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1)
#
# Settings for examples/ostest
#
CONFIG_EXAMPLES_OSTEST_LOOPS=1
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
#
# Settings for apps/nshlib
#
# CONFIG_NSH_BUILTIN_APPS - Support external registered,
# "named" applications that can be executed from the NSH
# command line (see apps/README.txt for more information).
# CONFIG_NSH_FILEIOSIZE - Size of a static I/O buffer
# CONFIG_NSH_STRERROR - Use strerror(errno)
# CONFIG_NSH_LINELEN - Maximum length of one command line
# CONFIG_NSH_NESTDEPTH - Max number of nested if-then[-else]-fi
# CONFIG_NSH_DISABLESCRIPT - Disable scripting support
# CONFIG_NSH_DISABLEBG - Disable background commands
# CONFIG_NSH_ROMFSETC - Use startup script in /etc
# CONFIG_NSH_CONSOLE - Use serial console front end
# CONFIG_NSH_TELNET - Use telnetd console front end
# CONFIG_NSH_ARCHINIT - Platform provides architecture
# specific initialization (nsh_archinitialize()).
#
# If CONFIG_NSH_TELNET is selected:
# CONFIG_NSH_IOBUFFER_SIZE -- Telnetd I/O buffer size
# CONFIG_NSH_DHCPC - Obtain address using DHCP
# CONFIG_NSH_IPADDR - Provides static IP address
# CONFIG_NSH_DRIPADDR - Provides static router IP address
# CONFIG_NSH_NETMASK - Provides static network mask
# CONFIG_NSH_NOMAC - Use a bogus MAC address
#
# If CONFIG_NSH_ROMFSETC is selected:
# CONFIG_NSH_ROMFSMOUNTPT - ROMFS mountpoint
# CONFIG_NSH_INITSCRIPT - Relative path to init script
# CONFIG_NSH_ROMFSDEVNO - ROMFS RAM device minor
# CONFIG_NSH_ROMFSSECTSIZE - ROMF sector size
# CONFIG_NSH_FATDEVNO - FAT FS RAM device minor
# CONFIG_NSH_FATSECTSIZE - FAT FS sector size
# CONFIG_NSH_FATNSECTORS - FAT FS number of sectors
# CONFIG_NSH_FATMOUNTPT - FAT FS mountpoint
#
CONFIG_NSH_BUILTIN_APPS=n
CONFIG_NSH_FILEIOSIZE=512
CONFIG_NSH_STRERROR=n
CONFIG_NSH_LINELEN=64
CONFIG_NSH_NESTDEPTH=3
CONFIG_NSH_DISABLESCRIPT=n
CONFIG_NSH_DISABLEBG=n
CONFIG_NSH_ROMFSETC=n
CONFIG_NSH_CONSOLE=y
CONFIG_NSH_TELNET=y
CONFIG_NSH_ARCHINIT=n
CONFIG_NSH_IOBUFFER_SIZE=512
CONFIG_NSH_DHCPC=n
CONFIG_NSH_NOMAC=y
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2)
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1)
CONFIG_NSH_NETMASK=(255<<24|255<<16|255<<8|0)
CONFIG_NSH_ROMFSMOUNTPT="/etc"
CONFIG_NSH_INITSCRIPT="init.d/rcS"
CONFIG_NSH_ROMFSDEVNO=0
CONFIG_NSH_ROMFSSECTSIZE=64
CONFIG_NSH_FATDEVNO=1
CONFIG_NSH_FATSECTSIZE=512
CONFIG_NSH_FATNSECTORS=1024
CONFIG_NSH_FATMOUNTPT=/tmp
#
# Architecture-specific NSH options
#
CONFIG_NSH_MMCSDSPIPORTNO=0
CONFIG_NSH_MMCSDSLOTNO=0
CONFIG_NSH_MMCSDMINOR=0
#
# I2C tool settings
#
# CONFIG_I2CTOOL_BUILTIN - Build the tools as an NSH built-in command
# CONFIG_I2CTOOL_MINBUS - Smallest bus index supported by the hardware (default 0).
# CONFIG_I2CTOOL_MAXBUS - Largest bus index supported by the hardware (default 3)
# CONFIG_I2CTOOL_MINADDR - Minium device address (default: 0x03)
# CONFIG_I2CTOOL_MAXADDR - Largest device address (default: 0x77)
# CONFIG_I2CTOOL_MAXREGADDR - Largest register address (default: 0xff)
# CONFIG_I2CTOOL_DEFFREQ - Default frequency (default: 1000000)
#
CONFIG_I2CTOOL_BUILTIN=y
CONFIG_I2CTOOL_MINBUS=1
CONFIG_I2CTOOL_MAXBUS=3
#CONFIG_I2CTOOL_MINADDR
#CONFIG_I2CTOOL_MAXADDR
#CONFIG_I2CTOOL_MAXREGADDR
CONFIG_I2CTOOL_DEFFREQ=100000
#
# Settings for examples/usbserial
#
# CONFIG_EXAMPLES_USBSERIAL_INONLY
# Only verify IN (device-to-host) data transfers. Default: both
# CONFIG_EXAMPLES_USBSERIAL_OUTONLY
# Only verify OUT (host-to-device) data transfers. Default: both
# CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL
# Send only small, single packet messages. Default: Send large and small.
# CONFIG_EXAMPLES_USBSERIAL_ONLYBIG
# Send only large, multi-packet messages. Default: Send large and small.
#
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
#
# Stack and heap information
#
# CONFIG_BOOT_RUNFROMFLASH - Some configurations support XIP
# operation from FLASH but must copy initialized .data sections to RAM.
# (should also be =n for the STM3240G-EVAL which always runs from flash)
# CONFIG_BOOT_COPYTORAM - Some configurations boot in FLASH
# but copy themselves entirely into RAM for better performance.
# CONFIG_CUSTOM_STACK - The up_ implementation will handle
# all stack operations outside of the nuttx model.
# CONFIG_STACK_POINTER - The initial stack pointer (arm7tdmi only)
# CONFIG_IDLETHREAD_STACKSIZE - The size of the initial stack.
# This is the thread that (1) performs the inital boot of the system up
# to the point where user_start() is spawned, and (2) there after is the
# IDLE thread that executes only when there is no other thread ready to
# run.
# CONFIG_USERMAIN_STACKSIZE - The size of the stack to allocate
# for the main user thread that begins at the user_start() entry point.
# CONFIG_PTHREAD_STACK_MIN - Minimum pthread stack size
# CONFIG_PTHREAD_STACK_DEFAULT - Default pthread stack size
# CONFIG_HEAP_BASE - The beginning of the heap
# CONFIG_HEAP_SIZE - The size of the heap
#
CONFIG_BOOT_RUNFROMFLASH=n
CONFIG_BOOT_COPYTORAM=n
CONFIG_CUSTOM_STACK=n
CONFIG_STACK_POINTER=
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
CONFIG_PTHREAD_STACK_MIN=256
CONFIG_PTHREAD_STACK_DEFAULT=2048
CONFIG_HEAP_BASE=
CONFIG_HEAP_SIZE=
Reference in New Issue View Git Blame Copy Permalink