257 lines
8.4 KiB
ReStructuredText
257 lines
8.4 KiB
ReStructuredText
================
|
||
ST Nucleo L496ZG
|
||
================
|
||
|
||
This page discusses issues unique to NuttX configurations for the STMicro
|
||
Nucleo-144 board for STM32L4 chips.
|
||
|
||
Nucleo L496ZG
|
||
=============
|
||
|
||
ST Nucleo L496ZG board from ST Micro is supported. See
|
||
|
||
http://www.st.com/content/st_com/en/products/evaluation-tools/product-evaluation-tools/mcu-eval-tools/stm32-mcu-eval-tools/stm32-mcu-nucleo/nucleo-l496zg.html
|
||
|
||
The Nucleo L496ZG order part number is NUCLEO-L496ZG. It is one member of
|
||
the STM32 Nucleo-144 board family.
|
||
|
||
NUCLEO-L496ZG Features
|
||
----------------------
|
||
|
||
- Microprocessor: STM32L496ZGT6 Core: ARM 32-bit Cortex®-M4 CPU with FPU,
|
||
80 MHz, MPU, and DSP instructions.
|
||
- Memory: 1024 KB Flash 320KB of SRAM (including 64KB of SRAM2)
|
||
- ADC: 3×12-bit: up to 24 channels
|
||
- DMA: 2 X 7-stream DMA controllers with FIFOs and burst support
|
||
- Timers: Up to 13 timers: (2x 16-bit lowpower), two 32-bit timers,
|
||
2x watchdogs, SysTick
|
||
- GPIO: 114 I/O ports with interrupt capability
|
||
- LCD: LCD-TFT Controller, Parallel interface
|
||
- I2C: 4 × I2C interfaces (SMBus/PMBus)
|
||
- U[S]ARTs: 3 USARTs, 2 UARTs (27 Mbit/s, ISO7816 interface, LIN, IrDA,
|
||
modem control)
|
||
- SPI/12Ss: 6/3 (simplex) (up to 50 Mbit/s), 3 with muxed simplex I2S
|
||
for audio class accuracy via internal audio PLL or external
|
||
clock
|
||
- QSPI: Dual mode Quad-SPI
|
||
- SAIs: 2 Serial Audio Interfaces
|
||
- CAN: 2 X CAN interface
|
||
- SDMMC interface
|
||
- USB: USB 2.0 full-speed device/host/OTG controller with on-chip PHY
|
||
- Camera Interface: 8/14 Bit
|
||
- CRC calculation unit
|
||
- TRG: True random number generator
|
||
- RTC
|
||
|
||
See https://developer.mbed.org/platforms/ST-Nucleo-L496ZG for additional
|
||
information about this board.
|
||
|
||
Hardware
|
||
========
|
||
Section needs updating
|
||
|
||
GPIO - there are 144 I/O lines on the STM32L4xxZx with various pins pined out
|
||
on the Nucleo 144.
|
||
|
||
Keep in mind that:
|
||
|
||
- The I/O is 3.3 Volt not 5 Volt like on the Arduino products.
|
||
- The Nucleo-144 board family has 3 pages of Solder Bridges AKA Solder
|
||
Blobs (SB) that can alter the factory configuration. We will note SB
|
||
in effect but will assume the factory default settings.
|
||
|
||
Our main concern is establishing a console and LED utilization for
|
||
debugging.
|
||
|
||
Buttons
|
||
-------
|
||
|
||
B1 USER: the user button is connected to the I/O PC13 (Tamper support, SB173
|
||
ON and SB180 OFF)
|
||
|
||
LEDs
|
||
----
|
||
|
||
The Board provides a 3 user LEDs, LD1-LD3
|
||
LED1 (Green) PB_0 (SB120 ON and SB119 OFF)
|
||
LED2 (Blue) PB_7 (SB139 ON)
|
||
LED3 (Red) PB_14 (SP118 ON)
|
||
|
||
- When the I/O is HIGH value, the LEDs are on.
|
||
- When the I/O is LOW, the LEDs are off.
|
||
|
||
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
||
defined. In that case, the usage by the board port is defined in
|
||
include/board.h and src/stm32_autoleds.c. The LEDs are used to encode OS
|
||
related events as follows when the LEDs are available:
|
||
|
||
=================== ======================= === ===== ====
|
||
SYMBOL Meaning RED GREEN BLUE
|
||
=================== ======================= === ===== ====
|
||
LED_STARTED NuttX has been started OFF OFF OFF
|
||
LED_HEAPALLOCATE Heap has been allocated OFF OFF ON
|
||
LED_IRQSENABLED Interrupts enabled OFF ON OFF
|
||
LED_STACKCREATED Idle stack created OFF ON ON
|
||
LED_INIRQ In an interrupt NC NC ON (momentary)
|
||
LED_SIGNAL In a signal handler NC ON OFF (momentary)
|
||
LED_ASSERTION An assertion failed ON NC ON (momentary)
|
||
LED_PANIC The system has crashed ON OFF OFF (flashing 2Hz)
|
||
LED_IDLE MCU is is sleep mode ON OFF OFF
|
||
=================== ======================= === ===== ====
|
||
|
||
OFF - means that the OS is still initializing. Initialization is very fast
|
||
so if you see this at all, it probably means that the system is
|
||
hanging up somewhere in the initialization phases.
|
||
|
||
GREEN - This means that the OS completed initialization.
|
||
|
||
BLUE - Whenever and interrupt or signal handler is entered, the BLUE LED is
|
||
illuminated and extinguished when the interrupt or signal handler
|
||
exits.
|
||
|
||
VIOLET - If a recovered assertion occurs, the RED and blue LED will be
|
||
illuminated briefly while the assertion is handled. You will
|
||
probably never see this.
|
||
|
||
Flashing RED - In the event of a fatal crash, all other LEDs will be
|
||
extinguished and RED LED will FLASH at a 2Hz rate.
|
||
|
||
Thus if the GREEN LED is lit, NuttX has successfully booted and is,
|
||
apparently, running normally. If the RED LED is flashing at
|
||
approximately 2Hz, then a fatal error has been detected and the system has
|
||
halted.
|
||
|
||
Serial Consoles
|
||
===============
|
||
|
||
USART3
|
||
------
|
||
|
||
Default board is configured to use USART3 as console.
|
||
|
||
Pins and Connectors::
|
||
|
||
FUNC GPIO Connector
|
||
Pin NAME
|
||
---- --- ------- ----
|
||
TXD: PC4 CN8-9, A4
|
||
RXD: PC5 CN8-11, A5
|
||
---- --- ------- ----
|
||
|
||
You must use a 3.3 TTL to RS-232 converter or a USB to 3.3V TTL::
|
||
|
||
Nucleo 144 FTDI TTL-232R-3V3
|
||
------------- -------------------
|
||
TXD - CN8-9 - RXD - Pin 5 (Yellow)
|
||
RXD - CN8-11 - TXD - Pin 4 (Orange)
|
||
GND - GND Pin 1 (Black)
|
||
------------- -------------------
|
||
|
||
*Note you will be reverse RX/TX
|
||
|
||
Use make menuconfig to configure USART3 as the console::
|
||
|
||
CONFIG_STM32L4_USART3=y
|
||
CONFIG_USART3_SERIALDRIVER=y
|
||
CONFIG_USART3_SERIAL_CONSOLE=y
|
||
CONFIG_USART3_RXBUFSIZE=256
|
||
CONFIG_USART3_TXBUFSIZE=256
|
||
CONFIG_USART3_BAUD=115200
|
||
CONFIG_USART3_BITS=8
|
||
CONFIG_USART3_PARITY=0
|
||
CONFIG_USART3_2STOP=0
|
||
|
||
USART2
|
||
------
|
||
|
||
USART 2 could be used as console as well.
|
||
|
||
Virtual COM Port
|
||
----------------
|
||
|
||
Yet another option is to use LPUART1 and the USB virtual COM port. This
|
||
option may be more convenient for long term development, but is painful
|
||
to use during board bring-up. However the LPUART peripheral has not yet
|
||
been tested for this board.
|
||
|
||
Solder Bridges. This configuration requires::
|
||
|
||
PG7 LPUART1 TX SB131 ON and SB195 OFF (Default)
|
||
PG8 LPUART1 RX SB130 ON and SB193 OFF (Default)
|
||
|
||
Default
|
||
-------
|
||
|
||
As shipped, the virtual COM port is enabled.
|
||
|
||
SPI
|
||
---
|
||
|
||
Since this board is so generic, having a quick way to vet the SPI
|
||
configuration seams in order. So the board provides a quick test
|
||
that can be selected vi CONFIG_NUCLEO_SPI_TEST that will initialize
|
||
the selected buses (SPI1-SPI3) and send some text on the bus at
|
||
application initialization time board_app_initialize.
|
||
|
||
SDIO
|
||
----
|
||
|
||
To test the SD performance one can use a SparkFun microSD Sniffer
|
||
from https://www.sparkfun.com/products/9419 or similar board
|
||
and connect it as follows::
|
||
|
||
VCC V3.3 CN11 16
|
||
GND GND CN11-8
|
||
CMD PD2 CN11-4
|
||
CLK PC12 CN11-3
|
||
DAT0 - PC8 CN12-2
|
||
DAT1 - PC9 CN12-1
|
||
DAT2 PC10 CN11-1
|
||
CD PC11 CN11-2
|
||
|
||
Configurations
|
||
==============
|
||
|
||
nsh
|
||
---
|
||
|
||
Configures the NuttShell (nsh) located at apps/examples/nsh for the
|
||
Nucleo-144 boards. The Configuration enables the serial interfaces
|
||
on USART6. Support for builtin applications is enabled, but in the base
|
||
configuration no builtin applications are selected (see NOTES below).
|
||
|
||
NOTES:
|
||
|
||
1. This configuration uses the mconf-based configuration tool. To
|
||
change this configuration using that tool, you should:
|
||
|
||
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
||
see additional README.txt files in the NuttX tools repository.
|
||
|
||
b. If this is the initial configuration then execute::
|
||
|
||
./tools/configure.sh nucleo-l496zg:nsh
|
||
|
||
in nuttx/ in order to start configuration process.
|
||
Caution: Doing this step more than once will overwrite .config with
|
||
the contents of the nucleo-l496zg/nsh/defconfig file.
|
||
|
||
c. Execute 'make oldconfig' in nuttx/ in order to refresh the
|
||
configuration.
|
||
|
||
d. Execute 'make menuconfig' in nuttx/ in order to start the
|
||
reconfiguration process.
|
||
|
||
e. Save the .config file to reuse it in the future starting at step d.
|
||
|
||
2. By default, this configuration uses the ARM GNU toolchain
|
||
for Linux. That can easily be reconfigured, of course.::
|
||
|
||
CONFIG_HOST_LINUX=y : Builds under Linux
|
||
CONFIG_ARM_TOOLCHAIN_GNU_EABI=y : ARM GNU for Linux
|
||
|
||
3. Although the default console is LPUART1 (which would correspond to
|
||
the Virtual COM port) I have done all testing with the console
|
||
device configured for USART3 (see instruction above under "Serial
|
||
Consoles).
|