sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
6336d79bb3
nuttx/configs/sama5d3x-ek/include/board.h

288 lines
12 KiB
C
Raw Blame History

/************************************************************************************
* configs/sama5df3x-ek/include/board.h
*
* Copyright (C) 2013 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
************************************************************************************/
#ifndef __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_H
#define __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_H
/************************************************************************************
* Included Files
************************************************************************************/
#include <nuttx/config.h>
/************************************************************************************
* Definitions
************************************************************************************/
/* Clocking *************************************************************************/
/* After power-on reset, the SAMA5 device is running on a 12MHz internal RC. These
* definitions will configure operational clocking.
*/
#if 1 /* #if !defined(CONFIG_SAMA5_OHCI) || defined(CONFIG_SAMA5_EHCI) */
/* This is the configuration provided in the Atmel example code. This setup results
* in a CPU clock of 396MHz.
*
* In this configuration, UPLL is the source of the UHPHS clock (if enabled).
*/
# include <arch/board/board_396MHz.h>
#else
/* OHCI Only. This is an alternative slower configuration that will produce a 48MHz
* USB clock with the required accuracy using only PLLA. When PPLA is used to clock
* OHCI, an additional requirement is the PLLACK be a multiple of 48MHz. This setup
* results in a CPU clock of 384MHz.
*/
# include <arch/board/board_384MHz.h>
#endif
/* LCD Geometry and Timing */
#define BOARD_LCD_WIDTH 800 /* Display width (pixels) */
#define BOARD_LCD_HEIGHT 480 /* Display height (pixels) */
#define BOARD_LCD_PIXELCLOCK 33260000 /* Pixel clock */
#define BOARD_LCDC_GUARDTIME 9 /* Guard time */
#define BOARD_LCD_VSPW 2 /* Vertical pulse width (lines) */
#define BOARD_LCD_HSPW 128 /* Horizontal pulse width (LCDDOTCLK) */
#define BOARD_LCD_VFPW 37 /* Vertical front porch (lines) */
#define BOARD_LCD_VBPW 8 /* Vertical back porch (lines) */
#define BOARD_LCD_HFPW 168 /* Horizontal front porch (LCDDOTCLK cycles) */
#define BOARD_LCD_HBPW 88 /* Horizontal back porch (LCDDOTCLK cycles) */
/* LED definitions ******************************************************************/
/* There are two LEDs on the SAMA5D3 series-CM board that can be controlled
* by software. A blue LED is controlled via PIO pins. A red LED normally
* provides an indication that power is supplied to the board but can also
* be controlled via software.
*
* PE25. This blue LED is pulled high and is illuminated by pulling PE25
* low.
*
* PE24. The red LED is also pulled high but is driven by a transistor so
* that it is illuminated when power is applied even if PE24 is not
* configured as an output. If PE24 is configured as an output, then the
* LCD is illuminated by a high output.
*/
/* LED index values for use with sam_setled() */
#define BOARD_BLUE 0
#define BOARD_RED 1
#define BOARD_NLEDS 2
/* LED bits for use with sam_setleds() */
#define BOARD_BLUE_BIT (1 << BOARD_BLUE)
#define BOARD_RED_BIT (1 << BOARD_RED)
/* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
* defined. In that case, the usage by the board port is defined in
* include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
* events as follows:
*
* SYMBOL Val Meaning LED state
* Blue Red
* ----------------- --- ----------------------- -------- -------- */
#define LED_STARTED 0 /* NuttX has been started OFF OFF */
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF OFF */
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF OFF */
#define LED_STACKCREATED 1 /* Idle stack created ON OFF */
#define LED_INIRQ 2 /* In an interrupt No change */
#define LED_SIGNAL 2 /* In a signal handler No change */
#define LED_ASSERTION 2 /* An assertion failed No change */
#define LED_PANIC 3 /* The system has crashed OFF Blinking */
#undef LED_IDLE /* MCU is is sleep mode Not used */
/* Thus if the blue LED is statically on, NuttX has successfully booted and
* is, apparently, running normmally. If the red is flashing at
* approximately 2Hz, then a fatal error has been detected and the system
* has halted.
*/
/* Button definitions ***************************************************************/
/* There are five push button switches on the SAMA5D3X-EK base board:
*
* 1. One Reset, board reset (BP1)
* 2. One Wake up, push button to bring the processor out of low power mode
* (BP2)
* 3. One User momentary Push Button
* 4. One Disable CS Push Button
*
* Only the momentary push button is controllable by software (labeled
* "PB_USER1" on the board):
*
* - PE27. Pressing the switch connect PE27 to grounded. Therefore, PE27
* must be pulled high internally. When the button is pressed the SAMA5
* will sense "0" is on PE27.
*/
#define BUTTON_USER1 0
#define NUM_BUTTONS 1
#define BUTTON_USER1_BIT (1 << BUTTON_USER1)
/* PIO configuration ****************************************************************/
/* LCDC */
#define PIO_LCD_DAT16 PIO_LCD_DAT16_2
#define PIO_LCD_DAT17 PIO_LCD_DAT17_2
#define PIO_LCD_DAT18 PIO_LCD_DAT18_2
#define PIO_LCD_DAT19 PIO_LCD_DAT19_2
#define PIO_LCD_DAT20 PIO_LCD_DAT20_2
#define PIO_LCD_DAT21 PIO_LCD_DAT21_2
#define PIO_LCD_DAT22 PIO_LCD_DAT22_1
#define PIO_LCD_DAT23 PIO_LCD_DAT23_1
/************************************************************************************
* Assembly Language Macros
************************************************************************************/
#ifdef __ASSEMBLY__
.macro config_sdram
.endm
#endif /* __ASSEMBLY__ */
/************************************************************************************
* Public Data
************************************************************************************/
#ifndef __ASSEMBLY__
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C" {
#else
#define EXTERN extern
#endif
/************************************************************************************
* Public Function Prototypes
************************************************************************************/
/************************************************************************************
* Name: sam_boardinitialize
*
* Description:
* All SAMA5 architectures must provide the following entry point. This entry point
* is called early in the intitialization -- after all memory has been configured
* and mapped but before any devices have been initialized.
*
************************************************************************************/
void sam_boardinitialize(void);
/************************************************************************************
* Name: sam_phyirq
*
* Description:
* This function may be called to register an interrupt handler that will be
* called when an interrupt is received from a PHY.
*
************************************************************************************/
#if defined(CONFIG_NET) && (defined(CONFIG_SAMA5_EMAC) || defined(CONFIG_SAMA5_GMAC)) && \
defined(CONFIG_SAMA5_PIOE_IRQ)
xcpt_t sam_phyirq(int intf, xcpt_t irqhandler);
#endif
/************************************************************************************
* Name: sam_ledinit, sam_setled, and sam_setleds
*
* Description:
* If CONFIG_ARCH_LEDS is defined, then NuttX will control the on-board LEDs. If
* CONFIG_ARCH_LEDS is not defined, then the following interfaces are available to
* control the LEDs from user applications.
*
************************************************************************************/
#ifndef CONFIG_ARCH_LEDS
void sam_ledinit(void);
void sam_setled(int led, bool ledon);
void sam_setleds(uint8_t ledset);
#endif
/************************************************************************************
* Name: up_buttoninit
*
* Description:
* up_buttoninit() must be called to initialize button resources. After that,
* up_buttons() may be called to collect the current state of all buttons or
* up_irqbutton() may be called to register button interrupt handlers.
*
************************************************************************************/
#ifdef CONFIG_ARCH_BUTTONS
void up_buttoninit(void);
/************************************************************************************
* Name: up_buttons
*
* Description:
* After up_buttoninit() has been called, up_buttons() may be called to collect
* the state of all buttons. up_buttons() returns an 8-bit bit set with each bit
* associated with a button. See the BUTTON* definitions above for the meaning of
* each bit in the returned value.
*
************************************************************************************/
uint8_t up_buttons(void);
/************************************************************************************
* Name: up_irqbutton
*
* Description:
* This function may be called to register an interrupt handler that will be
* called when a button is depressed or released. The ID value is one of the
* BUTTON* definitions provided above. The previous interrupt handler address is
* returned (so that it may restored, if so desired).
*
************************************************************************************/
#ifdef CONFIG_SAMA5_PIOE_IRQ
xcpt_t up_irqbutton(int id, xcpt_t irqhandler);
#endif
#endif /* CONFIG_ARCH_BUTTONS */
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* !__ASSEMBLY__ */
#endif /* __CONFIGS_SAMA5D3X_EK_INCLUDE_BOARD_H */
Reference in New Issue View Git Blame Copy Permalink