d42fc094fa
arm: stm32: codestyle fixes
* arm: stm32f0l0g0: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32f7: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32h7: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32l4: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
* arm: stm32: codestyle fixes
After the board restructuration is time for codestyle cleanup
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Approved-by: Gregory Nutt <gnutt@nuttx.org>
516 lines
20 KiB
C
516 lines
20 KiB
C
/****************************************************************************
|
|
* boards/arm/stm32/viewtool-stm32f107/src/viewtool_stm32f107.h
|
|
*
|
|
* Copyright (C) 2013-2014, 2016, 2018 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
|
* used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_STM32_VIEWTOOL_STM32F107_SRC_H
|
|
#define __BOARDS_ARM_STM32_VIEWTOOL_STM32F107_SRC_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#include <nuttx/compiler.h>
|
|
#include <stdint.h>
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
/* Configuration ************************************************************/
|
|
/* Assume that everything is supported */
|
|
|
|
#define HAVE_USBDEV 1
|
|
#define HAVE_MMCSD 1
|
|
#define HAVE_RTC_DRIVER 1
|
|
|
|
/* Handle chip differences */
|
|
|
|
#if defined(CONFIG_ARCH_CHIP_STM32F103VC)
|
|
# undef CONFIG_STM32_OTGFS
|
|
#elif defined(CONFIG_ARCH_CHIP_STM32F107VC)
|
|
# undef CONFIG_STM32_USB
|
|
# undef CONFIG_STM32_SDIO
|
|
#else
|
|
# error Unknown chip on Viewtool board
|
|
# undef HAVE_USBDEV
|
|
# undef HAVE_MMCSD
|
|
#endif
|
|
|
|
/* Check if USB is enabled */
|
|
|
|
#if !defined(CONFIG_STM32_OTGFS) && !defined(CONFIG_STM32_USB)
|
|
# undef HAVE_USBDEV
|
|
#elif !defined(CONFIG_USBDEV)
|
|
# warning CONFIG_STM32_OTGFS (F107) or CONFIG_STM32_USB (F103) is enabled but CONFIG_USBDEV is not
|
|
# undef HAVE_USB
|
|
#endif
|
|
|
|
/* Can't support MMC/SD features if the SDIO peripheral is disabled */
|
|
|
|
#ifndef CONFIG_STM32_SDIO
|
|
# undef HAVE_MMCSD
|
|
#endif
|
|
|
|
/* Can't support MMC/SD features if mountpoints are disabled */
|
|
|
|
#ifdef CONFIG_DISABLE_MOUNTPOINT
|
|
# undef HAVE_MMCSD
|
|
#endif
|
|
|
|
/* Default MMC/SD slot number/device minor number */
|
|
|
|
#define VIEWTOOL_MMCSD_SLOTNO 0
|
|
|
|
/* Check if we can support the RTC driver */
|
|
|
|
#if !defined(CONFIG_RTC) || !defined(CONFIG_RTC_DRIVER)
|
|
# undef HAVE_RTC_DRIVER
|
|
#endif
|
|
|
|
/* procfs File System */
|
|
|
|
#ifdef CONFIG_FS_PROCFS
|
|
# ifdef CONFIG_NSH_PROC_MOUNTPOINT
|
|
# define STM32_PROCFS_MOUNTPOINT CONFIG_NSH_PROC_MOUNTPOINT
|
|
# else
|
|
# define STM32_PROCFS_MOUNTPOINT "/proc"
|
|
# endif
|
|
#endif
|
|
|
|
/* GPIO Configuration *******************************************************/
|
|
/* LEDs
|
|
*
|
|
* There are four LEDs on the ViewTool STM32F103/F107 board that can be controlled
|
|
* by software: LED1 through LED4. All pulled high and can be illuminated by
|
|
* driving the output to low
|
|
*
|
|
* LED1 PA6
|
|
* LED2 PA7
|
|
* LED3 PB12
|
|
* LED4 PB13
|
|
*/
|
|
|
|
#define GPIO_LED1 (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz|\
|
|
GPIO_OUTPUT_SET | GPIO_PORTA | GPIO_PIN6)
|
|
#define GPIO_LED2 (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz|\
|
|
GPIO_OUTPUT_SET | GPIO_PORTA | GPIO_PIN7)
|
|
#define GPIO_LED3 (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz|\
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN12)
|
|
#define GPIO_LED4 (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz|\
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN13)
|
|
|
|
/* Buttons ******************************************************************/
|
|
/* All pulled high and will be sensed low when depressed.
|
|
*
|
|
* SW2 PC11 Needs J42 closed
|
|
* SW3 PC12 Needs J43 closed
|
|
* SW4 PA0 Needs J44 closed
|
|
*/
|
|
|
|
#define MIN_IRQBUTTON BUTTON_SW2
|
|
#define MAX_IRQBUTTON BUTTON_SW4
|
|
#define NUM_IRQBUTTONS (BUTTON_SW4 - BUTTON_SW2 + 1)
|
|
|
|
#define GPIO_SW2 (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTC | GPIO_PIN11)
|
|
#define GPIO_SW3 (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTC | GPIO_PIN12)
|
|
#define GPIO_SW4 (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTA | GPIO_PIN10)
|
|
|
|
/* microSD Card Interface
|
|
*
|
|
* microSD Connector
|
|
* -----------------
|
|
*
|
|
* ----------------------------- ------------------------- --------------------------------
|
|
* Connector J17 GPIO CONFIGURATION(s)
|
|
* PIN SIGNAL LEGEND (no remapping) DP83848C Board
|
|
* --- ------------- ----------- ------------------------- --------------------------------
|
|
* 1 VDD 3.3 N/A N/A 3.3
|
|
* 2 GND N/A N/A GND
|
|
* 3 PC8 SDIO_D0 GPIO_SDIO_D0 D0
|
|
* 4 PD2 SDIO_CMD GPIO_SDIO_CMD CMD
|
|
* 5 PC12 SDIO_CLK GPIO_SDIO_CK CLK
|
|
* 6 PC11 SDIO_D3 GPIO_SDIO_D3 D3
|
|
* 7 PC10 SDIO_D2 GPIO_SDIO_D2 D2
|
|
* 8 PC9 SDIO_D1 GPIO_SDIO_D1 D1
|
|
* 9 PA8 CD Board-specific GPIO input CD
|
|
* --- ------------- ----------- ------------------------- --------------------------------
|
|
*
|
|
* NOTES:
|
|
* 1. The STM32F107 does not support the SDIO/memory card interface. So the SD card
|
|
* cannot be used with the STM32F107 (unless the pin-out just happens to match up
|
|
* with an SPI-based card interface???)
|
|
*/
|
|
|
|
#ifdef CONFIG_ARCH_CHIP_STM32F103VC
|
|
# define GPIO_SD_CD (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_EXTI| \
|
|
GPIO_PORTA | GPIO_PIN8)
|
|
#endif
|
|
|
|
/* USB
|
|
*
|
|
* The Viewtool base board has a USB Mini-B connector. Only USB device can
|
|
* be supported with this connector.
|
|
*
|
|
* ------------------------- ------------------------------------
|
|
* USB Connector
|
|
* J10 mini-USB GPIO CONFIGURATION(s)
|
|
* --- --------- ----------- ------------------------------------
|
|
* Pin Signal
|
|
* --- --------- ----------- ------------------------------------
|
|
* 1 USB_VBUS VDD_USB (No sensing available)
|
|
* 2 OTG_DM PA11 GPIO_OTGFS_DM (F107) GPIO_USB_DM (F103)
|
|
* 3 OTG_DP PA12 GPIO_OTGFS_DP (F107) GPIO_USB_DP (F103)
|
|
* 4 OTG_ID PA10 GPIO_OTGFS_ID (F107)
|
|
* 5 Shield N/A N/A
|
|
* 6 Shield N/A N/A
|
|
* 7 Shield N/A N/A
|
|
* 8 Shield N/A N/A
|
|
* 9 Shield N/A N/A
|
|
* PE11 USB_EN GPIO controlled soft pull-up (if J51 closed)
|
|
*
|
|
* NOTES:
|
|
* 1. GPIO_OTGFS_VBUS (F107) should not be configured. No VBUS sensing
|
|
* 2. GPIO_OTGFS_SOF (F107) is not used
|
|
* 3. The OTG FS module has is own, internal soft pull-up logic. J51 should
|
|
* be open so that PE11 activity does effect USB.
|
|
*/
|
|
|
|
#ifdef CONFIG_ARCH_CHIP_STM32F103VC
|
|
# define GPIO_USB_PULLUP (GPIO_OUTPUT | GPIO_CNF_OUTOD | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTE | GPIO_PIN11)
|
|
#endif
|
|
|
|
/* LCD
|
|
*
|
|
* An LCD may be connected via J11. Only the STM32F103 supports the FSMC signals
|
|
* needed to drive the LCD.
|
|
*
|
|
* The LCD features an (1) HY32D module with built-in SSD1289 LCD controller, and (a)
|
|
* a XPT2046 touch screen controller.
|
|
*
|
|
* LCD Connector
|
|
* -------------
|
|
*
|
|
* ----------------------------- ------------------------ --------------------------------
|
|
* Connector J11 GPIO CONFIGURATION(s)
|
|
* PIN SIGNAL LEGEND (F103 only) LCD Module
|
|
* --- ------------- ----------- ------------------------ --------------------------------
|
|
* 1 VDD_5 NC N/A 5V ---
|
|
* 2 GND GND N/A GND ---
|
|
* 3 PD14 DATA0 GPIO_NPS_D0 D0 HY32D
|
|
* 4 PD15 DATA1 GPIO_NPS_D1 D1 HY32D
|
|
* 5 PD0 DATA2 GPIO_NPS_D2 D2 HY32D
|
|
* 6 PD1 DATA3 GPIO_NPS_D3 D3 HY32D
|
|
* 7 PE7 DATA4 GPIO_NPS_D4 D4 HY32D
|
|
* 8 PE8 DATA5 GPIO_NPS_D5 D5 HY32D
|
|
* 9 PE9 DATA6 GPIO_NPS_D6 D6 HY32D
|
|
* 10 PE10 DATA7 GPIO_NPS_D7 D7 HY32D
|
|
* 11 PE11 DATA8 GPIO_NPS_D8 D8 HY32D
|
|
* 12 PE12 DATA9 GPIO_NPS_D9 D9 HY32D
|
|
* 13 PE13 DATA10 GPIO_NPS_D10 D10 HY32D
|
|
* 14 PE14 DATA11 GPIO_NPS_D11 D11 HY32D
|
|
* 15 PE15 DATA12 GPIO_NPS_D12 D12 HY32D
|
|
* 16 PD8 DATA13 GPIO_NPS_D13 D13 HY32D
|
|
* 17 PD9 DATA14 GPIO_NPS_D14 D14 HY32D
|
|
* 18 PD10 DATA15 GPIO_NPS_D15 D15 HY32D
|
|
* 19 (3) LCD_CS GPIO_NPS_NE1 CS HY32D
|
|
* 20 PD11 LCD_RS GPIO_NPS_A16 RS HY32D
|
|
* 21 PD5 LCD_R/W GPIO_NPS_NWE WR HY32D
|
|
* 22 PD4 LCD_RD GPIO_NPS_NOE RD HY32D
|
|
* 23 PB1 LCD_RESET (GPIO) RESET HY32D
|
|
* 24 N/C NC N/A TE (unused?)
|
|
* 25 VDD_3.3 BL_VCC N/A BLVDD CA6219 (Drives LCD backlight)
|
|
* 26 GND BL_GND N/A BLGND CA6219
|
|
* 27 PB0 BL_PWM GPIO_TIM3_CH3OUT(2) BL_CNT CA6219
|
|
* 28 PC5 LCDTP_IRQ (GPIO) TP_IRQ XPT2046
|
|
* 29 PC4 LCDTP_CS (GPIO) TP_CS XPT2046
|
|
* 30 PB13 LCDTP_CLK GPIO_SPI2_SCK TP_SCK XPT2046
|
|
* 31 PB15 LCDTP_DIN GPIO_SPI2_MOSI TP_SI XPT2046
|
|
* 32 PB14 LCDTP_DOUT GPIO_SPI2_MISO TP_SO XPT2046
|
|
* 33 VDD_3.3 VDD_3.3 N/A 3.3V ---
|
|
* 34 GND GND N/A GND ---
|
|
* --- ------------- ----------- ------------------------ --------------------------------
|
|
*
|
|
* NOTES:
|
|
* 1) Only the F103 version of the board supports the FSMC
|
|
* 2) No remap
|
|
* 3) LCD_CS is controlled by J13 JUMPER4 (under the LCD unfortunately):
|
|
*
|
|
* 1->2 : PD7 (GPIO_NPS_NE1) enables the multiplexor : 1E\ enable input (active LOW)
|
|
* 3->4 : PD13 provides 1A0 input (1A1 is grounded). : 1A0 address input
|
|
* So will chip enable to either LCD_CS or
|
|
* Flash_CS.
|
|
* 5->6 : 1Y0 output to LCD_CS : 1Y0 address output
|
|
* 7->8 : 1Y1 output to Flash_CE : 1Y1 address output
|
|
*
|
|
* Truth Table:
|
|
* 1E\ 1A0 1A1 1Y0 1Y1
|
|
* --- --- --- --- ---
|
|
* HI N/A N/A HI HI
|
|
* LO LO LO LO HI
|
|
* LO HI LO HI LO
|
|
*/
|
|
|
|
#define GPIO_LCD_RESET (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTB| GPIO_PIN1)
|
|
#define GPIO_LCDTP_IRQ (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTC | GPIO_PIN5)
|
|
#define GPIO_LCDTP_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTC | GPIO_PIN4)
|
|
|
|
/* Freescale MPL115A barometer (optional add-on)
|
|
*
|
|
* This board support logic includes support for a Freescale MPL115A barometer
|
|
* using SPI3 with chip select on PB6.
|
|
*/
|
|
|
|
#define GPIO_MPL115A_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN6)
|
|
|
|
/* FT80x GUI Discrete I/O (See README.txt for details):
|
|
*
|
|
* ------ ----------- --------------------
|
|
* NAME VIEWTOOL STM32
|
|
* ------ ----------- --------------------
|
|
* CS# J8 Pin 12 PA4/NSS1 (For SPI1)
|
|
* CS# J8 Pin 6 PB12/NSS2 (For SPI2)
|
|
* INT# J18 Pin 8 PA1
|
|
* PD# J18 Pin 6 PC5
|
|
*/
|
|
|
|
#if defined(CONFIG_VIEWTOOL_FT80X_SPI1)
|
|
# define FT80X_SPIBUS 1
|
|
# define GPIO_FT80X_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTA | GPIO_PIN4)
|
|
#elif defined(CONFIG_VIEWTOOL_FT80X_SPI2)
|
|
# define FT80X_SPIBUS 2
|
|
# define GPIO_FT80X_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN12)
|
|
#endif
|
|
#define GPIO_FT80X_INT (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTA | GPIO_PIN1)
|
|
#define GPIO_FT80_PD (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_CLEAR | GPIO_PORTC| GPIO_PIN5)
|
|
|
|
/* MAX3421E USB HOST Discrete I/O (See README.txt for details):
|
|
*
|
|
* ------ ----------- --------------------
|
|
* NAME VIEWTOOL STM32
|
|
* ------ ----------- --------------------
|
|
* CS# J8 Pin 12 PA4/NSS1 (For SPI1)
|
|
* CS# J8 Pin 6 PB12/NSS2 (For SPI2)
|
|
* INT# J18 Pin 10 PA0
|
|
* RST# J18 Pin 8 PA1
|
|
* GPX J18 Pin 6 PC5 (not used)
|
|
*/
|
|
|
|
#if defined(CONFIG_VIEWTOOL_MAX3421E_SPI1)
|
|
# define MAX3421E_SPIBUS 1
|
|
# define GPIO_MAX3421E_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTA | GPIO_PIN4)
|
|
#elif defined(CONFIG_VIEWTOOL_MAX3421E_SPI2)
|
|
# define MAX3421E_SPIBUS 2
|
|
# define GPIO_MAX3421E_CS (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_SET | GPIO_PORTB | GPIO_PIN12)
|
|
#endif
|
|
#define GPIO_MAX3421E_INT (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_EXTI | GPIO_PORTA | GPIO_PIN0)
|
|
#define GPIO_MAX3421E_RST (GPIO_OUTPUT | GPIO_CNF_OUTPP | GPIO_MODE_50MHz | \
|
|
GPIO_OUTPUT_CLEAR | GPIO_PORTA | GPIO_PIN1)
|
|
#define GPIO_MAX3421E_GPX (GPIO_INPUT | GPIO_CNF_INFLOAT | GPIO_MODE_INPUT | \
|
|
GPIO_PORTC | GPIO_PIN5)
|
|
|
|
/****************************************************************************
|
|
* Public Functions
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_bringup
|
|
*
|
|
* Description:
|
|
* Perform architecture-specific initialization
|
|
*
|
|
* CONFIG_BOARD_LATE_INITIALIZE=y :
|
|
* Called from board_late_initialize().
|
|
*
|
|
* CONFIG_BOARD_LATE_INITIALIZE=n && CONFIG_LIB_BOARDCTL=y :
|
|
* Called from the NSH library
|
|
*
|
|
****************************************************************************/
|
|
|
|
int stm32_bringup(void);
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_spidev_initialize
|
|
*
|
|
* Description:
|
|
* Called to configure SPI chip select GPIO pins for the M3 Wildfire board.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void weak_function stm32_spidev_initialize(void);
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_led_initialize
|
|
*
|
|
* Description:
|
|
* Configure LEDs. LEDs are left in the OFF state.
|
|
*
|
|
****************************************************************************/
|
|
|
|
void stm32_led_initialize(void);
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_usbdev_initialize
|
|
*
|
|
* Description:
|
|
* Called from stm32_usbdev_initialize very early in initialization to
|
|
* setup USB-related GPIO pins for the Viewtool STM32F107 board.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#if defined(CONFIG_STM32_OTGFS) && defined(CONFIG_USBDEV)
|
|
void weak_function stm32_usbdev_initialize(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_tsc_setup
|
|
*
|
|
* Description:
|
|
* This function is called by board-bringup logic to configure the
|
|
* touchscreen device. This function will register the driver as
|
|
* /dev/inputN where N is the minor device number.
|
|
*
|
|
* Input Parameters:
|
|
* minor - The input device minor number
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_INPUT_ADS7843E
|
|
int stm32_tsc_setup(int minor);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_sdinitialize
|
|
*
|
|
* Description:
|
|
* Initialize the SPI-based SD card. Requires CONFIG_DISABLE_MOUNTPOINT=n
|
|
* and CONFIG_STM32_SPI1=y
|
|
*
|
|
****************************************************************************/
|
|
|
|
int stm32_sdinitialize(int minor);
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_can_setup
|
|
*
|
|
* Description:
|
|
* Initialize CAN and register the CAN device
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifdef CONFIG_CAN
|
|
int stm32_can_setup(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_mpl115ainitialize
|
|
*
|
|
* Description:
|
|
* Initialize and register the MPL115A Pressure Sensor driver.
|
|
*
|
|
* Input Parameters:
|
|
* devpath - The full path to the driver to register. E.g., "/dev/press0"
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) on success; a negated errno value on failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#if defined(CONFIG_SPI) && defined(CONFIG_SENSORS_MPL115A) && defined(CONFIG_STM32_SPI3)
|
|
int stm32_mpl115ainitialize(FAR const char *devpath);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_ft80x_setup
|
|
*
|
|
* Description:
|
|
* This function is called by board-bringup logic to configure the
|
|
* FT80x GUI device.
|
|
*
|
|
* Input Parameters:
|
|
* None
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#if defined(CONFIG_VIEWTOOL_FT80X_SPI1) || defined(CONFIG_VIEWTOOL_FT80X_SPI2)
|
|
int stm32_ft80x_setup(void);
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: stm32_max3421e_setup
|
|
*
|
|
* Description:
|
|
* This function is called by board-bringup logic to configure the
|
|
* MAX3421E USB host.
|
|
*
|
|
* Input Parameters:
|
|
* None
|
|
*
|
|
* Returned Value:
|
|
* Zero is returned on success. Otherwise, a negated errno value is
|
|
* returned to indicate the nature of the failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#if defined(CONFIG_VIEWTOOL_MAX3421E_SPI1) || defined(CONFIG_VIEWTOOL_MAX3421E_SPI2)
|
|
int stm32_max3421e_setup(void);
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_STM32_VIEWTOOL_STM32F107_SRC_H */
|