68951e8d72
* Remove multiple newlines at the end of files * Remove the whitespace from the end of lines
104 lines
3.8 KiB
Plaintext
104 lines
3.8 KiB
Plaintext
README
|
|
======
|
|
|
|
This directory holds NuttX board support for the TI LaunchXL-CC1310. This
|
|
board features the CC1310F128 part with 128Kb of FLASH and 20Kb of SRAM.
|
|
|
|
Contents
|
|
========
|
|
|
|
o Status
|
|
o Serial Console
|
|
o LEDs and Buttons
|
|
o Using J-Link
|
|
|
|
Status
|
|
======
|
|
|
|
2019-01-21: Fragmentary board support in place. The initial intent
|
|
of this board support is simply to assist in the CC13x0 architecture
|
|
development. Serious board development will occur later. At present,
|
|
the CC13x0 does not even compile error-free: Compilation of cc14x0_rom.c
|
|
fails because the DDI0 OSC header file has not yet been ported.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
The on-board XDS110 Debugger provide a USB virtual serial console using
|
|
UART0 (PA0/U0RX and PA1/U0TX).
|
|
|
|
A J-Link debugger is used (see below), then the RXD/TXD jumper pins can
|
|
be used to support a serial console through appropriate TTL level adapater
|
|
(RS-232 or USB serial).
|
|
|
|
LEDs and Buttons
|
|
================
|
|
|
|
LEDs
|
|
----
|
|
|
|
The LaunchXL-cc1310 and two LEDs controlled by software: DIO7_GLED (CR1)
|
|
and DIO6_RLED (CR2). A high output value illuminates an LED.
|
|
|
|
DIO7_GLED CR1 High output illuminuates
|
|
DIO6_RLED CR2 High output illuminuates
|
|
|
|
If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
any way. The definitions provided in the board.h header file can be used
|
|
to access individual LEDs.
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/cc1312_autoleds.c. The LEDs are used to encode
|
|
OS-related events as follows:
|
|
|
|
SYMBOL Meaning LED state
|
|
GLED RLED
|
|
------------------ ------------------------ ------ ------
|
|
LED_STARTED NuttX has been started OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF ON
|
|
LED_IRQSENABLED Interrupts enabled OFF ON
|
|
LED_STACKCREATED Idle stack created ON OFF
|
|
LED_INIRQ In an interrupt N/C GLOW
|
|
LED_SIGNAL In a signal handler N/C GLOW
|
|
LED_ASSERTION An assertion failed N/C GLOW
|
|
LED_PANIC The system has crashed OFF Blinking
|
|
LED_IDLE MCU is is sleep mode Not used
|
|
|
|
Thus iF GLED is statically on, NuttX has successfully booted and is,
|
|
apparently, running normally. A soft glow of the RLED means that the
|
|
board is taking interrupts. If GLED is off and GLED is flashing at
|
|
approximately 2Hz, then a fatal error has been detected and the system
|
|
has halted.
|
|
|
|
Buttons
|
|
-------
|
|
|
|
The LaunchXL-CC1310 has two push-puttons:
|
|
|
|
DIO13_BTN1 SW1 Low input sensed when depressed
|
|
DIO14_BTN2 SW2 Low input sensed when depressed
|
|
|
|
Using J-Link
|
|
============
|
|
|
|
Reference https://wiki.segger.com/CC1310_LaunchPad:
|
|
|
|
When shipped, the TI CC1310 LaunchPad evaluation board is configured to be
|
|
used with the on-board debug probe. In order to use it with J-Link, the
|
|
on-board debug probe needs to be isolated to make sure that it does not
|
|
drive the debug signals. This can be done by removing some jumpers next
|
|
to the XDS110 Out / CC1310 In connector [RXD, TXD, RST, TMS, TCK, TDO, TDI,
|
|
SWO]. After isolating the on-board probe, the CC130F128 device can be
|
|
debugged using J-Link. The J-Link needs to be connected to the board
|
|
using the micro JTAG connector marked "In".
|
|
|
|
I use the Olimex ARM-JTAG-20-10 to interface with the board:
|
|
https://www.olimex.com/Products/ARM/JTAG/ARM-JTAG-20-10/
|
|
|
|
NOTE: When connecting the J-Link GDB server, the interface must be set to
|
|
JTAG, not SWD as you might expect.
|
|
|
|
The RXD/TXD pins. PA0/U0RX and PA1/U0TX, can then support a Serial console
|
|
using the appropriate TTL adapter (TTL to RS-232 or TTL to USB serial).
|