sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
6b255474e3
nuttx/arch/avr/src/at32uc3/at32uc3_lowconsole.c
patacongo e69cbad010 Add logic so that a RAM log can be used in place of a console device 
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4380 42af7a65-404d-4744-a932-0658087f49c3
2012-02-11 03:50:52 +00:00

392 lines
12 KiB
C
Raw Blame History

/******************************************************************************
* arch/avr/src/at32uc3/at32uc3_lowconsole.c
*
* Copyright (C) 2010, 2012 Gregory Nutt. All rights reserved.
* Author: Gregory Nutt <gnutt@nuttx.org>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* 3. Neither the name NuttX nor the names of its contributors may be
* used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************/
/******************************************************************************
* Included Files
******************************************************************************/
#include <nuttx/config.h>
#include "at32uc3_config.h"
#include <assert.h>
#include <debug.h>
#include <arch/irq.h>
#include <arch/board/board.h>
#include "up_arch.h"
#include "up_internal.h"
#include "at32uc3_internal.h"
#include "at32uc3_pm.h"
#include "at32uc3_usart.h"
#include "at32uc3_pinmux.h"
/******************************************************************************
* Private Definitions
******************************************************************************/
/* Select USART parameters for the selected console */
#if defined(CONFIG_USART0_SERIAL_CONSOLE)
# define AVR32_CONSOLE_BASE AVR32_USART0_BASE
# define AVR32_CONSOLE_BAUD CONFIG_USART0_BAUD
# define AVR32_CONSOLE_BITS CONFIG_USART0_BITS
# define AVR32_CONSOLE_PARITY CONFIG_USART0_PARITY
# define AVR32_CONSOLE_2STOP CONFIG_USART0_2STOP
#elif defined(CONFIG_USART1_SERIAL_CONSOLE)
# define AVR32_CONSOLE_BASE AVR32_USART1_BASE
# define AVR32_CONSOLE_BAUD CONFIG_USART1_BAUD
# define AVR32_CONSOLE_BITS CONFIG_USART1_BITS
# define AVR32_CONSOLE_PARITY CONFIG_USART1_PARITY
# define AVR32_CONSOLE_2STOP CONFIG_USART1_2STOP
#elif defined(CONFIG_USART2_SERIAL_CONSOLE)
# define AVR32_CONSOLE_BASE AVR32_USART2_BASE
# define AVR32_CONSOLE_BAUD CONFIG_USART2_BAUD
# define AVR32_CONSOLE_BITS CONFIG_USART2_BITS
# define AVR32_CONSOLE_PARITY CONFIG_USART2_PARITY
# define AVR32_CONSOLE_2STOP CONFIG_USART2_2STOP
#else
# error "No CONFIG_USARTn_SERIAL_CONSOLE Setting"
#endif
/******************************************************************************
* Private Types
******************************************************************************/
/******************************************************************************
* Private Function Prototypes
******************************************************************************/
/******************************************************************************
* Global Variables
******************************************************************************/
/******************************************************************************
* Private Variables
******************************************************************************/
/******************************************************************************
* Private Functions
******************************************************************************/
/******************************************************************************
* Name: usart_putreg
*
* Description:
* Write a value to a USART register
*
******************************************************************************/
#ifdef HAVE_RS232_DEVICE
static inline void usart_putreg(uintptr_t usart_base, unsigned int offset, uint32_t value)
{
putreg32(value, usart_base + offset);
}
#endif
/******************************************************************************
* Name: usart_getreg
*
* Description:
* Get a value from a USART register
*
******************************************************************************/
#ifdef HAVE_RS232_DEVICE
static inline uint32_t usart_getreg(uintptr_t usart_base, unsigned int offset)
{
return getreg32(usart_base + offset);
}
#endif
/******************************************************************************
* Name: usart_setbaudrate
*
* Description:
* Configure the UART baud rate.
*
******************************************************************************/
#ifdef HAVE_RS232_DEVICE
static void usart_setbaudrate(uintptr_t usart_base, uint32_t baudrate)
{
uint32_t cd;
uint32_t mr;
/* Select 16x or 8x oversampling mode or go to synchronous mode */
mr = usart_getreg(usart_base, AVR32_USART_MR_OFFSET);
if (baudrate < AVR32_PBA_CLOCK / 16)
{
/* Select 16x oversampling mode and clear the SYNC mode bit */
mr &= ~(USART_MR_OVER|USART_MR_SYNC);
/* Calculate the clock divider assuming 16x oversampling */
cd = (AVR32_PBA_CLOCK + (baudrate << 3)) / (baudrate << 4);
}
else if (baudrate < AVR32_PBA_CLOCK / 8)
{
/* Select 8x oversampling mode and clear the SYNC mode bit */
mr &= ~USART_MR_SYNC;
mr |= USART_MR_OVER;
/* Calculate the clock divider assuming 16x oversampling */
cd = (AVR32_PBA_CLOCK + (baudrate << 2)) / (baudrate << 3);
}
else
{
/* Set the SYNC mode bit */
mr |= USART_MR_SYNC;
/* Use the undivided PBA clock */
cd = AVR32_PBA_CLOCK / baudrate;
}
DEBUGASSERT(cd > 0 && cd < 65536);
usart_putreg(usart_base, AVR32_USART_MR_OFFSET, mr);
usart_putreg(usart_base, AVR32_USART_BRGR_OFFSET, cd);
}
#endif
/******************************************************************************
* Public Functions
******************************************************************************/
/******************************************************************************
* Name: usart_reset
*
* Description:
* Reset a USART.
*
******************************************************************************/
#ifdef HAVE_RS232_DEVICE
void usart_reset(uintptr_t usart_base)
{
irqstate_t flags;
/* Disable all USART interrupts */
flags = irqsave();
usart_putreg(usart_base, AVR32_USART_IDR_OFFSET, 0xffffffff);
irqrestore(flags);
/* Reset mode and other registers */
usart_putreg(usart_base, AVR32_USART_MR_OFFSET, 0); /* Reset mode register */
usart_putreg(usart_base, AVR32_USART_RTOR_OFFSET, 0); /* Reset receiver timeout register */
usart_putreg(usart_base, AVR32_USART_TTGR_OFFSET, 0); /* Reset transmitter timeguard reg */
/* Disable RX and TX, put USART in reset, disable handshaking signals */
usart_putreg(usart_base, AVR32_USART_CR_OFFSET,
USART_CR_RSTRX|USART_CR_RSTTX|USART_CR_RSTSTA|USART_CR_RSTIT|
USART_CR_RSTNACK|USART_CR_DTRDIS|USART_CR_RTSDIS);
}
#endif
/******************************************************************************
* Name: usart_configure
*
* Description:
* Configure a USART as a RS-232 UART.
*
******************************************************************************/
#ifdef HAVE_RS232_DEVICE
void usart_configure(uintptr_t usart_base, uint32_t baud, unsigned int parity,
unsigned int nbits, bool stop2)
{
uint32_t regval;
/* Reset the USART and disable RX and TX */
usart_reset(usart_base);
/* Configure STOP bits */
regval = USART_MR_MODE_NORMAL|USART_MR_CHMODE_NORMAL; /* Normal RS-232 mode */
regval |= stop2 ? USART_MR_NBSTOP_2 : USART_MR_NBSTOP_1;
/* Configure parity */
switch (parity)
{
case 0:
default:
regval |= USART_MR_PAR_NONE;
break;
case 1:
regval |= USART_MR_PAR_ODD;
break;
case 2:
regval |= USART_MR_PAR_EVEN;
break;
}
/* Configure the number of bits per word */
DEBUGASSERT(nbits >= 5 && nbits <= 9);
if (nbits == 9)
{
regval |= USART_MR_MODE9;
}
else
{
regval |= USART_MR_CHRL_BITS(nbits);
}
usart_putreg(usart_base, AVR32_USART_MR_OFFSET, regval);
/* Set the baud rate generation register */
usart_setbaudrate(usart_base, baud);
/* Enable RX and TX */
regval = usart_getreg(usart_base, AVR32_USART_CR_OFFSET);
regval |= (USART_CR_RXEN|USART_CR_TXEN);
usart_putreg(usart_base, AVR32_USART_CR_OFFSET, regval);
}
#endif
/******************************************************************************
* Name: up_consoleinit
*
* Description:
* Initialize a console for debug output. This function is called very
* early in the intialization sequence to configure the serial console uart
* (only).
*
******************************************************************************/
void up_consoleinit(void)
{
uint32_t pbamask = 0;
uint32_t regval;
/* Setup GPIO pins fand enable module clocking or each configured USART/UART */
#ifdef CONFIG_AVR32_USART0_RS232
/* PINMUX_USART0_RXD and PINMUX_USART0_TXD must be defined in board.h. It
* must define them be be one of {PINMUX_USART0_RXD_1, PINMUX_USART0_RXD_2}
* and {PINMUX_USART_0TXD_1, PINMUX_USART0_TXD_2}, respectively.
*/
at32uc3_configgpio(PINMUX_USART0_RXD);
at32uc3_configgpio(PINMUX_USART0_TXD);
/* Enable clocking to USART0 (This should be the default state after reset) */
pbamask |= PM_PBAMASK_USART0;
#endif
#ifdef CONFIG_AVR32_USART1_RS232
/* PINMUX_USART1_RXD and PINMUX_USART1_TXD must be defined in board.h. It
* must define them be be one of {PINMUX_USART1_RXD_1, PINMUX_USART1_RXD_2,
* PINMUX_USART1_RXD_3} and {PINMUX_USART1_TXD_1, PINMUX_USART1_TXD_2,
* PINMUX_USART1_TXD_3}, respectively.
*/
at32uc3_configgpio(PINMUX_USART1_RXD);
at32uc3_configgpio(PINMUX_USART1_TXD);
/* Enable clocking to USART1 (This should be the default state after reset) */
pbamask |= PM_PBAMASK_USART1;
#endif
#ifdef CONFIG_AVR32_USART2_RS232
/* PINMUX_USART2_RXD and PINMUX_USART2_TXD must be defined in board.h. It
* must define them be be one of {PINMUX_USART2_RXD_1, PINMUX_USART2_RXD_2}
* and {PINMUX_USART2_TXD_1, PINMUX_USART2_TXD_2}, respectively.
*/
at32uc3_configgpio(PINMUX_USART2_RXD);
at32uc3_configgpio(PINMUX_USART2_TXD);
/* Enable clocking to USART2 (This should be the default state after reset) */
pbamask |= PM_PBAMASK_USART2;
#endif
/* Enable selected clocks (and disabled unselected clocks) */
regval = getreg32(AVR32_PM_PBAMASK);
regval &= ~(PM_PBAMASK_USART0|PM_PBAMASK_USART1|PM_PBAMASK_USART2);
regval |= pbamask;
putreg32(regval, AVR32_PM_PBAMASK);
/* Then configure the console here (if it is not going to be configured
* by up_earlyserialinit()).
*/
#if defined(HAVE_SERIAL_CONSOLE) && !defined(USE_EARLYSERIALINIT)
usart_configure(AVR32_CONSOLE_BASE, AVR32_CONSOLE_BAUD, AVR32_CONSOLE_PARITY,
AVR32_CONSOLE_BITS, (bool)AVR32_CONSOLE_2STOP);
#endif
}
/******************************************************************************
* Name: up_lowputc
*
* Description:
* Output one byte on the serial console
*
******************************************************************************/
void up_lowputc(char ch)
{
#ifdef HAVE_SERIAL_CONSOLE
/* Wait until the TX to become ready */
while ((usart_getreg(AVR32_CONSOLE_BASE, AVR32_USART_CSR_OFFSET) & USART_CSR_TXRDY) == 0);
/* Then send the character */
usart_putreg(AVR32_CONSOLE_BASE, AVR32_USART_THR_OFFSET, (uint32_t)ch);
#endif
}
Reference in New Issue View Git Blame Copy Permalink