6b412c873b
can be omitted from the command line when flashing. Signed-off-by: Abdelatif Guettouche <abdelatif.guettouche@espressif.com>
160 lines
5.3 KiB
Makefile
160 lines
5.3 KiB
Makefile
############################################################################
|
|
# tools/esp32/Config.mk
|
|
#
|
|
# Licensed to the Apache Software Foundation (ASF) under one or more
|
|
# contributor license agreements. See the NOTICE file distributed with
|
|
# this work for additional information regarding copyright ownership. The
|
|
# ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance with the
|
|
# License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
# License for the specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
############################################################################
|
|
|
|
# These are the macros that will be used in the NuttX make system to compile
|
|
# and assemble source files and to insert the resulting object files into an
|
|
# archive. These replace the default definitions at tools/Config.mk
|
|
|
|
ifeq ($(CONFIG_ESP32_FLASH_2M),y)
|
|
FLASH_SIZE := 2MB
|
|
else ifeq ($(CONFIG_ESP32_FLASH_4M),y)
|
|
FLASH_SIZE := 4MB
|
|
else ifeq ($(CONFIG_ESP32_FLASH_8M),y)
|
|
FLASH_SIZE := 8MB
|
|
else ifeq ($(CONFIG_ESP32_FLASH_16M),y)
|
|
FLASH_SIZE := 16MB
|
|
endif
|
|
|
|
ifeq ($(CONFIG_ESP32_FLASH_MODE_DIO),y)
|
|
FLASH_MODE := dio
|
|
else ifeq ($(CONFIG_ESP32_FLASH_MODE_DOUT),y)
|
|
FLASH_MODE := dout
|
|
else ifeq ($(CONFIG_ESP32_FLASH_MODE_QIO),y)
|
|
FLASH_MODE := qio
|
|
else ifeq ($(CONFIG_ESP32_FLASH_MODE_QOUT),y)
|
|
FLASH_MODE := qout
|
|
endif
|
|
|
|
ifeq ($(CONFIG_ESP32_FLASH_FREQ_80M),y)
|
|
FLASH_FREQ := 80m
|
|
else ifeq ($(CONFIG_ESP32_FLASH_FREQ_40M),y)
|
|
FLASH_FREQ := 40m
|
|
else ifeq ($(CONFIG_ESP32_FLASH_FREQ_26M),y)
|
|
FLASH_FREQ := 26m
|
|
else ifeq ($(CONFIG_ESP32_FLASH_FREQ_20M),y)
|
|
FLASH_FREQ := 20m
|
|
endif
|
|
|
|
ifeq ($(CONFIG_ESP32_FLASH_DETECT),y)
|
|
ESPTOOL_WRITEFLASH_OPTS := -fs detect -fm dio -ff $(FLASH_FREQ)
|
|
else
|
|
ESPTOOL_WRITEFLASH_OPTS := -fs $(FLASH_SIZE) -fm dio -ff $(FLASH_FREQ)
|
|
endif
|
|
|
|
# Configure the variables according to build environment
|
|
|
|
ifdef ESPTOOL_BINDIR
|
|
ifeq ($(CONFIG_ESP32_APP_FORMAT_LEGACY),y)
|
|
BL_OFFSET := 0x1000
|
|
PT_OFFSET := 0x8000
|
|
APP_OFFSET := 0x10000
|
|
BOOTLOADER := $(ESPTOOL_BINDIR)/bootloader-esp32.bin
|
|
PARTITION_TABLE := $(ESPTOOL_BINDIR)/partition-table-esp32.bin
|
|
APP_IMAGE := nuttx.bin
|
|
FLASH_BL := $(BL_OFFSET) $(BOOTLOADER)
|
|
FLASH_PT := $(PT_OFFSET) $(PARTITION_TABLE)
|
|
ESPTOOL_BINS := $(FLASH_BL) $(FLASH_PT)
|
|
else ifeq ($(CONFIG_ESP32_APP_FORMAT_MCUBOOT),y)
|
|
BL_OFFSET := 0x1000
|
|
BOOTLOADER := $(ESPTOOL_BINDIR)/mcuboot-esp32.bin
|
|
FLASH_BL := $(BL_OFFSET) $(BOOTLOADER)
|
|
ESPTOOL_BINS := $(FLASH_BL)
|
|
endif
|
|
endif
|
|
|
|
ifeq ($(CONFIG_ESP32_APP_FORMAT_LEGACY),y)
|
|
APP_OFFSET := 0x10000
|
|
APP_IMAGE := nuttx.bin
|
|
FLASH_APP := $(APP_OFFSET) $(APP_IMAGE)
|
|
else ifeq ($(CONFIG_ESP32_APP_FORMAT_MCUBOOT),y)
|
|
ifeq ($(CONFIG_ESP32_ESPTOOL_TARGET_PRIMARY),y)
|
|
VERIFIED := --confirm
|
|
APP_OFFSET := $(CONFIG_ESP32_OTA_PRIMARY_SLOT_OFFSET)
|
|
else ifeq ($(CONFIG_ESP32_ESPTOOL_TARGET_SECONDARY),y)
|
|
VERIFIED :=
|
|
APP_OFFSET := $(CONFIG_ESP32_OTA_SECONDARY_SLOT_OFFSET)
|
|
endif
|
|
|
|
APP_IMAGE := nuttx_signed.bin
|
|
FLASH_APP := $(APP_OFFSET) $(APP_IMAGE)
|
|
endif
|
|
|
|
ESPTOOL_BINS += $(FLASH_APP)
|
|
|
|
ifeq ($(CONFIG_ESP32_QEMU_IMAGE),y)
|
|
MK_QEMU_IMG=$(TOPDIR)/tools/esp32/mk_qemu_img.sh -b $(BOOTLOADER) -p $(PARTITION_TABLE)
|
|
else
|
|
MK_QEMU_IMG=
|
|
endif
|
|
|
|
# POSTBUILD -- Perform post build operations
|
|
|
|
ifeq ($(CONFIG_ESP32_APP_FORMAT_MCUBOOT),y)
|
|
define POSTBUILD
|
|
$(Q) echo "MKIMAGE: ESP32 binary"
|
|
$(Q) if ! imgtool version 1>/dev/null 2>&1; then \
|
|
echo ""; \
|
|
echo "imgtool not found. Please run: \"pip install imgtool\""; \
|
|
echo ""; \
|
|
echo "Run make again to create the nuttx_signed.bin image."; \
|
|
exit 1; \
|
|
fi
|
|
imgtool sign --pad --pad-sig $(VERIFIED) --align 4 -v 0 \
|
|
-H $(CONFIG_ESP32_APP_MCUBOOT_HEADER_SIZE) --pad-header \
|
|
-S $(CONFIG_ESP32_OTA_SLOT_SIZE) \
|
|
nuttx.bin nuttx_signed.bin
|
|
$(Q) echo "Generated: nuttx_signed.bin (MCUboot compatible)"
|
|
endef
|
|
else
|
|
define POSTBUILD
|
|
$(Q) echo "MKIMAGE: ESP32 binary"
|
|
$(Q) if ! esptool.py version 1>/dev/null 2>&1; then \
|
|
echo ""; \
|
|
echo "esptool.py not found. Please run: \"pip install esptool\""; \
|
|
echo ""; \
|
|
echo "Run make again to create the nuttx.bin image."; \
|
|
exit 1; \
|
|
fi
|
|
$(Q) if [ -z $(FLASH_SIZE) ]; then \
|
|
echo "Missing Flash memory size configuration for the ESP32 chip."; \
|
|
exit 1; \
|
|
fi
|
|
$(eval ESPTOOL_ELF2IMG_OPTS := -fs $(FLASH_SIZE) -fm $(FLASH_MODE) -ff $(FLASH_FREQ))
|
|
esptool.py -c esp32 elf2image $(ESPTOOL_ELF2IMG_OPTS) -o nuttx.bin nuttx
|
|
$(Q) echo "Generated: nuttx.bin (ESP32 compatible)"
|
|
$(Q) $(MK_QEMU_IMG)
|
|
endef
|
|
endif
|
|
|
|
# ESPTOOL_BAUD -- Serial port baud rate used when flashing/reading via esptool.py
|
|
|
|
ESPTOOL_BAUD ?= 921600
|
|
|
|
# DOWNLOAD -- Download binary image via esptool.py
|
|
|
|
define DOWNLOAD
|
|
$(Q) if [ -z $(ESPTOOL_PORT) ]; then \
|
|
echo "DOWNLOAD error: Missing serial port device argument."; \
|
|
echo "USAGE: make download ESPTOOL_PORT=<port> [ ESPTOOL_BAUD=<baud> ] [ ESPTOOL_BINDIR=<dir> ]"; \
|
|
exit 1; \
|
|
fi
|
|
esptool.py -c esp32 -p $(ESPTOOL_PORT) -b $(ESPTOOL_BAUD) write_flash $(ESPTOOL_WRITEFLASH_OPTS) $(ESPTOOL_BINS)
|
|
endef
|