nuttx/configs/sam3u-ek/touchscreen/defconfig
patacongo f39a3c9417 Remove several unused configuration values
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5113 42af7a65-404d-4744-a932-0658087f49c3
2012-09-08 04:29:48 +00:00

566 lines
13 KiB
Plaintext
Executable File

############################################################################
# configs/sam3u-ek/touchscreen/defconfig
#
# Copyright (C) 2011 Gregory Nutt. All rights reserved.
# Author: Gregory Nutt <gnutt@nuttx.org>
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
#
# 1. Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in
# the documentation and/or other materials provided with the
# distribution.
# 3. Neither the name NuttX nor the names of its contributors may be
# used to endorse or promote products derived from this software
# without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
# "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
# LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
# FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
# COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
# BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
# OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
# ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
# POSPIBILITY OF SUCH DAMAGE.
#
############################################################################
#
# Architecture Selection
#
CONFIG_ARCH="arm"
CONFIG_ARCH_ARM=y
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP="sam3u"
CONFIG_ARCH_CHIP_AT91SAM3U4E=y
CONFIG_ARCH_BOARD="sam3u-ek"
CONFIG_ARCH_BOARD_SAM3UEK=y
CONFIG_BOARD_LOOPSPERMSEC=4768
CONFIG_DRAM_SIZE=32768
CONFIG_DRAM_START=0x20000000
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_INTERRUPTSTACK=n
CONFIG_ARCH_STACKDUMP=y
CONFIG_ARCH_BOOTLOADER=n
CONFIG_ARCH_LEDS=y
CONFIG_ARCH_BUTTONS=y
CONFIG_ARCH_CALIBRATION=n
CONFIG_ARCH_DMA=n
#
# Identify toolchain and linker options
#
CONFIG_SAM3U_CODESOURCERYW=n
CONFIG_SAM3U_CODESOURCERYL=n
CONFIG_SAM3U_DEVKITARM=n
CONFIG_SAM3U_BUILDROOT=y
#
# Individual subsystems can be enabled:
#
CONFIG_SAM3U_DMA=n
CONFIG_SAM3U_HSMCI=n
CONFIG_SAM3U_NAND=n
CONFIG_SAM3U_SPI=y
CONFIG_SAM3U_UART=y
CONFIG_SAM3U_USART0=n
CONFIG_SAM3U_USART1=n
CONFIG_SAM3U_USART2=n
CONFIG_SAM3U_USART3=n
#
# Some subsystems can be configured to operate in different ways..
# The drivers need to know how to configure the subsystem.
#
CONFIG_GPIOA_IRQ=y
CONFIG_GPIOB_IRQ=n
CONFIG_GPIOC_IRQ=n
CONFIG_USART0_ISUART=y
CONFIG_USART1_ISUART=y
CONFIG_USART2_ISUART=y
CONFIG_USART3_ISUART=y
#
# SAM3U specific serial device driver settings
#
CONFIG_UART_SERIAL_CONSOLE=Y
CONFIG_USART0_SERIAL_CONSOLE=n
CONFIG_USART1_SERIAL_CONSOLE=n
CONFIG_USART2_SERIAL_CONSOLE=n
CONFIG_USART3_SERIAL_CONSOLE=n
CONFIG_UART_TXBUFSIZE=256
CONFIG_USART0_TXBUFSIZE=256
CONFIG_USART1_TXBUFSIZE=256
CONFIG_USART2_TXBUFSIZE=256
CONFIG_USART3_TXBUFSIZE=256
CONFIG_UART_RXBUFSIZE=256
CONFIG_USART0_RXBUFSIZE=256
CONFIG_USART1_RXBUFSIZE=256
CONFIG_USART2_RXBUFSIZE=256
CONFIG_USART3_RXBUFSIZE=256
CONFIG_UART_BAUD=115200
CONFIG_USART0_BAUD=115200
CONFIG_USART1_BAUD=115200
CONFIG_USART2_BAUD=115200
CONFIG_USART3_BAUD=115200
CONFIG_UART_BITS=8
CONFIG_USART0_BITS=8
CONFIG_USART1_BITS=8
CONFIG_USART2_BITS=8
CONFIG_USART3_BITS=8
CONFIG_UART_PARITY=0
CONFIG_USART0_PARITY=0
CONFIG_USART1_PARITY=0
CONFIG_USART2_PARITY=0
CONFIG_USART3_PARITY=0
CONFIG_UART_2STOP=0
CONFIG_USART0_2STOP=0
CONFIG_USART1_2STOP=0
CONFIG_USART2_2STOP=0
CONFIG_USART3_2STOP=0
#
# Input device configuration
#
CONFIG_INPUT=y
CONFIG_INPUT_ADS7843E=y
#
# General build options
#
CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=y
CONFIG_HAVE_LIBM=n
#
# General OS setup
#
CONFIG_USER_ENTRYPOINT="nsh_main"
CONFIG_DEBUG=n
CONFIG_DEBUG_VERBOSE=n
CONFIG_DEBUG_SYMBOLS=n
CONFIG_DEBUG_GRAPHICS=n
CONFIG_DEBUG_LCD=n
CONFIG_DEBUG_INPUT=n
CONFIG_MM_REGIONS=3
CONFIG_ARCH_LOWPUTC=y
CONFIG_RR_INTERVAL=200
CONFIG_SCHED_INSTRUMENTATION=n
CONFIG_TASK_NAME_SIZE=0
CONFIG_START_YEAR=2011
CONFIG_START_MONTH=9
CONFIG_START_DAY=30
CONFIG_GREGORIAN_TIME=n
CONFIG_JULIAN_TIME=n
CONFIG_DEV_CONSOLE=y
CONFIG_DEV_LOWCONSOLE=n
CONFIG_MUTEX_TYPES=n
CONFIG_PRIORITY_INHERITANCE=n
CONFIG_SEM_PREALLOCHOLDERS=0
CONFIG_SEM_NNESTPRIO=0
CONFIG_FDCLONE_DISABLE=n
CONFIG_FDCLONE_STDIO=n
CONFIG_SDCLONE_DISABLE=y
CONFIG_SCHED_WORKQUEUE=y
CONFIG_SCHED_WORKPRIORITY=192
CONFIG_SCHED_WORKPERIOD=50000
CONFIG_SCHED_WORKSTACKSIZE=1024
CONFIG_SIG_SIGWORK=4
CONFIG_SCHED_WAITPID=y
CONFIG_SCHED_ATEXIT=n
#
# Settings for NXFLAT
#
CONFIG_NXFLAT=y
CONFIG_NXFLAT_DUMPBUFFER=n
CONFIG_SYMTAB_ORDEREDBYNAME=y
#
# The following can be used to disable categories of
# APIs supported by the OS. If the compiler supports
# weak functions, then it should not be necessary to
# disable functions unless you want to restrict usage
# of those APIs.
#
# There are certain dependency relationships in these
# features.
#
# o mq_notify logic depends on signals to awaken tasks
# waiting for queues to become full or empty.
# o pthread_condtimedwait() depends on signals to wake
# up waiting tasks.
#
CONFIG_DISABLE_CLOCK=n
CONFIG_DISABLE_POSIX_TIMERS=n
CONFIG_DISABLE_PTHREAD=n
CONFIG_DISABLE_SIGNALS=n
CONFIG_DISABLE_MQUEUE=n
CONFIG_DISABLE_MOUNTPOINT=n
CONFIG_DISABLE_ENVIRON=n
CONFIG_DISABLE_POLL=y
#
# Misc libc settings
#
CONFIG_NOPRINTF_FIELDWIDTH=n
#
# Allow for architecture optimized implementations
#
# The architecture can provide optimized versions of the
# following to improve system performance
#
CONFIG_ARCH_MEMCPY=n
CONFIG_ARCH_MEMCMP=n
CONFIG_ARCH_MEMMOVE=n
CONFIG_ARCH_MEMSET=n
CONFIG_ARCH_STRCMP=n
CONFIG_ARCH_STRCPY=n
CONFIG_ARCH_STRNCPY=n
CONFIG_ARCH_STRLEN=n
CONFIG_ARCH_STRNLEN=n
CONFIG_ARCH_BZERO=n
#
# Sizes of configurable things (0 disables)
#
CONFIG_MAX_TASKS=16
CONFIG_MAX_TASK_ARGS=4
CONFIG_NPTHREAD_KEYS=4
CONFIG_NFILE_DESCRIPTORS=8
CONFIG_NFILE_STREAMS=8
CONFIG_NAME_MAX=32
CONFIG_STDIO_BUFFER_SIZE=256
CONFIG_NUNGET_CHARS=2
CONFIG_PREALLOC_MQ_MSGS=4
CONFIG_MQ_MAXMSGSIZE=32
CONFIG_MAX_WDOGPARMS=2
CONFIG_PREALLOC_WDOGS=4
CONFIG_PREALLOC_TIMERS=4
#
# Framebuffer driver options
#
CONFIG_FB_CMAP=n
CONFIG_FB_HWCURSOR=n
CONFIG_FB_HWCURSORIMAGE=n
#CONFIG_FB_HWCURSORSIZE
#CONFIG_FB_TRANSPARENCY
#
# Filesystem configuration
#
CONFIG_FS_FAT=y
CONFIG_FS_ROMFS=n
CONFIG_FS_FAT=y
CONFIG_FAT_LCNAMES=y
CONFIG_FAT_LFN=y
CONFIG_FAT_MAXFNAME=32
CONFIG_FS_NXFFS=n
CONFIG_FS_ROMFS=n
#
# SPI-based MMC/SD driver
#
CONFIG_MMCSD_NSLOTS=1
CONFIG_MMCSD_READONLY=n
CONFIG_MMCSD_SPICLOCK=12500000
#
# Block driver buffering
#
CONFIG_FS_READAHEAD=n
CONFIG_FS_WRITEBUFFER=n
#
# SDIO-based MMC/SD driver
#
CONFIG_SDIO_DMA=n
CONFIG_SDIO_BLOCKSETUP=y
CONFIG_MMCSD_MMCSUPPORT=n
CONFIG_MMCSD_HAVECARDDETECT=n
#
# TCP/IP and UDP support via uIP
#
CONFIG_NET=n
CONFIG_NET_IPv6=n
CONFIG_NSOCKET_DESCRIPTORS=0
CONFIG_NET_SOCKOPTS=y
CONFIG_NET_BUFSIZE=420
CONFIG_NET_TCP=n
CONFIG_NET_TCP_CONNS=40
CONFIG_NET_MAX_LISTENPORTS=40
CONFIG_NET_UDP=n
CONFIG_NET_UDP_CHECKSUMS=y
#CONFIG_NET_UDP_CONNS=10
CONFIG_NET_ICMP=n
CONFIG_NET_ICMP_PING=n
#CONFIG_NET_PINGADDRCONF=0
CONFIG_NET_STATISTICS=y
#CONFIG_NET_RECEIVE_WINDOW=
#CONFIG_NET_ARPTAB_SIZE=8
CONFIG_NET_BROADCAST=n
#
# UIP Network Utilities
#
CONFIG_NET_DHCP_LIGHT=n
CONFIG_NET_RESOLV_ENTRIES=4
#
# USB Device Configuration
#
CONFIG_USBDEV=n
CONFIG_USBDEV_ISOCHRONOUS=n
CONFIG_USBDEV_DUALSPEED=n
CONFIG_USBDEV_SELFPOWERED=y
CONFIG_USBDEV_REMOTEWAKEUP=n
CONFIG_USBDEV_MAXPOWER=100
CONFIG_USBDEV_TRACE=n
CONFIG_USBDEV_TRACE_NRECORDS=128
#
# USB Serial Device Configuration
#
CONFIG_PL2303=n
CONFIG_PL2303_EPINTIN=1
CONFIG_PL2303_EPBULKOUT=2
CONFIG_PL2303_EPBULKIN=3
CONFIG_PL2303_NWRREQS=4
CONFIG_PL2303_NRDREQS=4
CONFIG_PL2303_VENDORID=0x067b
CONFIG_PL2303_PRODUCTID=0x2303
CONFIG_PL2303_VENDORSTR="Nuttx"
CONFIG_PL2303_PRODUCTSTR="USBdev Serial"
CONFIG_PL2303_RXBUFSIZE=512
CONFIG_PL2303_TXBUFSIZE=512
#
# USB Storage Device Configuration
#
CONFIG_USBMSC=n
CONFIG_USBMSC_EP0MAXPACKET=64
CONFIG_USBMSC_EPBULKOUT=2
CONFIG_USBMSC_EPBULKIN=5
CONFIG_USBMSC_NRDREQS=2
CONFIG_USBMSC_NWRREQS=2
CONFIG_USBMSC_BULKINREQLEN=256
CONFIG_USBMSC_BULKOUTREQLEN=256
CONFIG_USBMSC_VENDORID=0x584e
CONFIG_USBMSC_VENDORSTR="NuttX"
CONFIG_USBMSC_PRODUCTID=0x5342
CONFIG_USBMSC_PRODUCTSTR="USBdev Storage"
CONFIG_USBMSC_VERSIONNO=0x0399
CONFIG_USBMSC_REMOVABLE=y
#
# Graphics related configuration settings
#
CONFIG_NX=y
CONFIG_NX_MULTIUSER=n
CONFIG_NX_NPLANES=1
CONFIG_NX_DISABLE_1BPP=y
CONFIG_NX_DISABLE_2BPP=y
CONFIG_NX_DISABLE_4BPP=y
CONFIG_NX_DISABLE_8BPP=y
CONFIG_NX_DISABLE_16BPP=n
CONFIG_NX_DISABLE_24BPP=y
CONFIG_NX_DISABLE_32BPP=y
CONFIG_NX_PACKEDMSFIRST=n
CONFIG_NX_LCDDRIVER=y
CONFIG_LCD_MAXPOWER=31
CONFIG_LCD_MAXCONTRAST=1
CONFIG_NX_MOUSE=y
CONFIG_NX_KBD=y
#CONFIG_NXTK_BORDERWIDTH=4
#CONFIG_NXTK_BORDERCOLOR1
#CONFIG_NXTK_BORDERCOLOR2
CONFIG_NXTK_AUTORAISE=n
CONFIG_NXFONT_SANS23X27=y
CONFIG_NXFONTS_CHARBITS=7
CONFIG_NX_BLOCKING=y
CONFIG_NX_MXSERVERMSGS=32
CONFIG_NX_MXCLIENTMSGS=16
#
# SAM3U-EK LCD Hardware Configuration
#
CONFIG_LCD_LANDSCAPE=n
CONFIG_LCD_PORTRAIT=y
#
# Settings for examples/uip
#
CONFIG_EXAMPLE_UIP_IPADDR=0x0a000002
CONFIG_EXAMPLE_UIP_DRIPADDR=0x0a000001
CONFIG_EXAMPLE_UIP_NETMASK=0xffffff00
CONFIG_EXAMPLE_UIP_DHCPC=n
#
# Settings for examples/nettest
CONFIG_EXAMPLE_NETTEST_SERVER=n
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=n
CONFIG_EXAMPLE_NETTEST_NOMAC=n
CONFIG_EXAMPLE_NETTEST_IPADDR=0x0a000002
CONFIG_EXAMPLE_NETTEST_DRIPADDR=0x0a000001
CONFIG_EXAMPLE_NETTEST_NETMASK=0xffffff00
CONFIG_EXAMPLE_NETTEST_CLIENTIP=0x0a000001
#
# Settings for examples/ostest
#
CONFIG_EXAMPLES_OSTEST_LOOPS=1
CONFIG_EXAMPLES_OSTEST_STACKSIZE=2048
CONFIG_EXAMPLES_OSTEST_NBARRIER_THREADS=3
#
# Settings for apps/nshlib
#
CONFIG_NSH_BUILTIN_APPS=y
CONFIG_NSH_FILEIOSIZE=512
CONFIG_NSH_STRERROR=n
CONFIG_NSH_LINELEN=64
CONFIG_NSH_NESTDEPTH=3
CONFIG_NSH_DISABLESCRIPT=n
CONFIG_NSH_DISABLEBG=n
CONFIG_NSH_ROMFSETC=n
CONFIG_NSH_CONSOLE=y
#CONFIG_NSH_CONDEV="/dev/ttyS1"
CONFIG_NSH_TELNET=n
CONFIG_NSH_ARCHINIT=n
CONFIG_NSH_IOBUFFER_SIZE=512
CONFIG_NSH_DHCPC=n
CONFIG_NSH_NOMAC=n
CONFIG_NSH_IPADDR=0x0a000002
CONFIG_NSH_DRIPADDR=0x0a000001
CONFIG_NSH_NETMASK=0xffffff00
CONFIG_NSH_ROMFSMOUNTPT="/etc"
CONFIG_NSH_INITSCRIPT="init.d/rcS"
CONFIG_NSH_ROMFSDEVNO=0
CONFIG_NSH_ROMFSSECTSIZE=64
CONFIG_NSH_FATDEVNO=1
CONFIG_NSH_FATSECTSIZE=512
CONFIG_NSH_FATNSECTORS=1024
CONFIG_NSH_FATMOUNTPT="/tmp"
#
# Architecture-specific NSH options
#
CONFIG_NSH_MMCSDSPIPORTNO=0
CONFIG_NSH_MMCSDSLOTNO=0
CONFIG_NSH_MMCSDMINOR=0
#
# Settings for examples/usbserial
#
CONFIG_EXAMPLES_USBSERIAL_INONLY=n
CONFIG_EXAMPLES_USBSERIAL_OUTONLY=n
CONFIG_EXAMPLES_USBSERIAL_ONLYSMALL=n
CONFIG_EXAMPLES_USBSERIAL_ONLYBIG=n
CONFIG_EXAMPLES_USBSERIAL_TRACEINIT=n
CONFIG_EXAMPLES_USBSERIAL_TRACECLASS=n
CONFIG_EXAMPLES_USBSERIAL_TRACETRANSFERS=n
CONFIG_EXAMPLES_USBSERIAL_TRACECONTROLLER=n
CONFIG_EXAMPLES_USBSERIAL_TRACEINTERRUPTS=n
#
# Settings for examples/nx
#
CONFIG_EXAMPLES_NX_BUILTIN=y
CONFIG_EXAMPLES_NX_VPLANE=0
CONFIG_EXAMPLES_NX_DEVNO=0
CONFIG_EXAMPLES_NX_BGCOLOR=0x7b5d
CONFIG_EXAMPLES_NX_COLOR1=0xe73f
CONFIG_EXAMPLES_NX_COLOR2=0xdefb
CONFIG_EXAMPLES_NX_TBCOLOR=0xad55
CONFIG_EXAMPLES_NX_FONTCOLOR=0x0000
CONFIG_EXAMPLES_NX_BPP=16
CONFIG_EXAMPLES_NX_RAWWINDOWS=n
CONFIG_EXAMPLES_NX_STACKSIZE=2048
CONFIG_EXAMPLES_NX_CLIENTPRIO=80
CONFIG_EXAMPLES_NX_SERVERPRIO=120
CONFIG_EXAMPLES_NX_NOTIFYSIGNO=4
#
# Settings for examples/nxhello
#
CONFIG_EXAMPLES_NXHELLO_BUILTIN=y
CONFIG_EXAMPLES_NXHELLO_VPLANE=0
CONFIG_EXAMPLES_NXHELLO_DEVNO=0
CONFIG_EXAMPLES_NXHELLO_BGCOLOR=0x0011
CONFIG_EXAMPLES_NXHELLO_FONTID=6
CONFIG_EXAMPLES_NXHELLO_FONTCOLOR=0xffdf
CONFIG_EXAMPLES_NXHELLO_BPP=16
CONFIG_EXAMPLES_NXHELLO_EXTERNINIT=n
#
# Settings for examples/nximage
#
CONFIG_EXAMPLES_NXIMAGE_BUILTIN=y
CONFIG_EXAMPLES_NXIMAGE_VPLANE=0
CONFIG_EXAMPLES_NXIMAGE_DEVNO=0
CONFIG_EXAMPLES_NXIMAGE_BPP=16
CONFIG_EXAMPLES_NXIMAGE_XSCALEp5=n
CONFIG_EXAMPLES_NXIMAGE_XSCALE1p5=y
CONFIG_EXAMPLES_NXIMAGE_XSCALE2p0=n
CONFIG_EXAMPLES_NXIMAGE_YSCALEp5=n
CONFIG_EXAMPLES_NXIMAGE_YSCALE1p5=y
CONFIG_EXAMPLES_NXIMAGE_YSCALE2p0=n
CONFIG_EXAMPLES_NXIMAGE_EXTERNINIT=n
#
# Settings for examples/nxlines
#
CONFIG_EXAMPLES_NXLINES_BUILTIN=n
CONFIG_EXAMPLES_NXLINES_VPLANE=0
CONFIG_EXAMPLES_NXLINES_DEVNO=0
CONFIG_EXAMPLES_NXLINES_BGCOLOR=0x0320
CONFIG_EXAMPLES_NXLINES_LINEWIDTH=16
CONFIG_EXAMPLES_NXLINES_LINECOLOR=0xffe0
CONFIG_EXAMPLES_NXLINES_BORDERWIDTH=4
CONFIG_EXAMPLES_NXLINES_BORDERCOLOR=0xffe0
CONFIG_EXAMPLES_NXLINES_CIRCLECOLOR=0xf7bb
CONFIG_EXAMPLES_NXLINES_BPP=16
CONFIG_EXAMPLES_NXLINES_EXTERNINIT=n
#
# Settings for examples/touchscreen
#
CONFIG_EXAMPLES_TOUCHSCREEN_BUILTIN=y
CONFIG_EXAMPLES_TOUCHSCREEN_MINOR=0
CONFIG_EXAMPLES_TOUCHSCREEN_DEVPATH="/dev/input0"
CONFIG_EXAMPLES_TOUCHSCREEN_NSAMPLES=25
#
# Stack and heap information
#
CONFIG_BOOT_RUNFROMFLASH=n
CONFIG_BOOT_COPYTORAM=n
CONFIG_CUSTOM_STACK=n
CONFIG_IDLETHREAD_STACKSIZE=1024
CONFIG_USERMAIN_STACKSIZE=2048
CONFIG_PTHREAD_STACK_MIN=256
CONFIG_PTHREAD_STACK_DEFAULT=2048
CONFIG_HEAP_BASE=
CONFIG_HEAP_SIZE=