sergiotarxz/nuttx
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
6c42928cd6
nuttx/boards/arm/lpc54xx/lpcxpresso-lpc54628/src/lpcxpresso-lpc54628.h
Xiang Xiao cd001725b7 arch/arm: Remove FAR and CODE from board folder(1) 
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
2022-05-03 16:50:52 +03:00

390 lines
11 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/lpc54xx/lpcxpresso-lpc54628/src/lpcxpresso-lpc54628.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_LPC54XX_LPCXPRESSO_LPC54628_SRC_LPCXPRESSO_LPC54628_H
#define __BOARDS_ARM_LPC54XX_LPCXPRESSO_LPC54628_SRC_LPCXPRESSO_LPC54628_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include "lpc54_config.h"
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
#define HAVE_I2CTOOL 1
#define HAVE_FT5x06 1
#define HAVE_MMCSD 1
#define HAVE_RTC_DRIVER 1
/* Do we need to register I2C drivers on behalf of the I2C tool? */
#ifdef CONFIG_SYSTEM_I2CTOOL
# ifndef CONFIG_I2C_DRIVER
# warning CONFIG_SYSTEM_I2CTOOL requires CONFIG_I2C_DRIVER
# undef HAVE_I2CTOOL
# endif
# ifndef HAVE_I2C_MASTER_DEVICE
# warning CONFIG_SYSTEM_I2CTOOL requires HAVE_I2C_MASTER_DEVICE
# undef HAVE_I2CTOOL
# endif
#else
# undef HAVE_I2CTOOL
#endif
/* Do we need to register FT5x06 touch panel driver? */
#ifdef CONFIG_INPUT_FT5X06
# ifndef CONFIG_LPC54_I2C2_MASTER
# warning CONFIG_INPUT_FT5X06 requires CONFIG_LPC54_I2C2_MASTER
# undef HAVE_FT5x06
# endif
# ifndef CONFIG_FT5X06_POLLMODE
# warning CONFIG_INPUT_FT5X06 requires CONFIG_FT5X06_POLLMODE
# undef HAVE_FT5x06
# endif
#else
# undef HAVE_FT5x06
#endif
/* MMC/SD support */
#ifdef CONFIG_LPC54_SDMMC
# ifndef CONFIG_MMCSD
# warning MMC/SD support requires CONFIG_MMCSD
# undef HAVE_MMCSD
# endif
# ifndef CONFIG_MMCSD_SDIO
# warning MMC/SD support requires CONFIG_MMCSD_SDIO
# undef HAVE_MMCSD
# endif
# ifdef CONFIG_DISABLE_MOUNTPOINT
# warning MMC/SD cannot be supported with CONFIG_DISABLE_MOUNTPOINT
# undef HAVE_MMCSD
# endif
# ifdef CONFIG_NSH_MMCSDMINOR
# define MMCSD_MINOR CONFIG_NSH_MMCSDMINOR
# else
# define MMCSD_MINOR 0
# endif
#else
# undef HAVE_MMCSD
#endif
/* Check if we can support the RTC driver */
#if !defined(CONFIG_RTC) || !defined(CONFIG_RTC_DRIVER)
# undef HAVE_RTC_DRIVER
#endif
/* Indices into a sparse I2C array. Used with lpc54_i2c_handle() */
#ifdef CONFIG_LPC54_I2C0_MASTER
# define I2C0NDX 0
# define I2C0CNT 1
# define __I2C1NX 1
#else
# define I2C0CNT 0
# define __I2C1NX 0
#endif
#ifdef CONFIG_LPC54_I2C1_MASTER
# define I2C1NDX __I2C1NX
# define I2C1CNT 1
# define __I2C2NX (__I2C1NX + 1)
#else
# define I2C1CNT 0
# define __I2C2NX 0
#endif
#ifdef CONFIG_LPC54_I2C2_MASTER
# define I2C2NDX __I2C2NX
# define I2C2CNT 1
# define __I2C3NX (__I2C2NX + 1)
#else
# define I2C2CNT 0
# define __I2C3NX __I2C2NX
#endif
#ifdef CONFIG_LPC54_I2C3_MASTER
# define I2C3NDX __I2C3NX
# define I2C3CNT 1
# define __I2C4NX (__I2C3NX + 1)
#else
# define I2C3CNT 0
# define __I2C4NX __I2C3NX
#endif
#ifdef CONFIG_LPC54_I2C4_MASTER
# define I2C4NDX __I2C4NX
# define I2C4CNT 1
# define __I2C5NX (__I2C4NX + 1)
#else
# define I2C4CNT 0
# define __I2C5NX __I2C4NX
#endif
#ifdef CONFIG_LPC54_I2C5_MASTER
# define I2C5NDX __I2C5NX
# define I2C5CNT 1
# define __I2C6NX (__I2C5NX + 1)
#else
# define I2C5CNT 0
# define __I2C6NX __I2C5NX
#endif
#ifdef CONFIG_LPC54_I2C6_MASTER
# define I2C6NDX __I2C6NX
# define I2C6CNT 1
# define __I2C7NX (__I2C6NX + 1)
#else
# define I2C6CNT 0
# define __I2C7NX __I2C6NX
#endif
#ifdef CONFIG_LPC54_I2C7_MASTER
# define I2C7NDX __I2C7NX
# define I2C7CNT 1
# define __I2C8NX (__I2C7NX + 1)
#else
# define I2C7CNT 0
# define __I2C8NX __I2C7NX
#endif
#ifdef CONFIG_LPC54_I2C8_MASTER
# define I2C8NDX __I2C8NX
# define I2C8CNT 1
# define __I2C9NX (__I2C8NX + 1)
#else
# define I2C8CNT 0
# define __I2C9NX __I2C8NX
#endif
#ifdef CONFIG_LPC54_I2C9_MASTER
# define I2CNDX __I2C9NX
# define I2C9CNT 1
#else
# define I2C9CNT 0
#endif
#define NI2C (I2C0CNT + I2C1CNT + I2C2CNT + I2C3CNT + I2C4CNT + \
I2C5CNT + I2C6CNT + I2C7CNT + I2C8CNT + I2C9CNT )
/* LED definitions **********************************************************/
/* The LPCXpress-LPC54628 has three user LEDs: D9, D11, and D12. These
* LEDs are for application use. They are illuminated when the driving
* signal from the LPC546xx is low. The LEDs are driven by ports P2-2 (D9),
* P3-3 (D11) and P3-14 (D12).
*/
#define GPIO_LED_D9 \
(GPIO_PORT2 | GPIO_PIN2 | GPIO_VALUE_ONE | GPIO_OUTPUT | \
GPIO_MODE_DIGITAL | GPIO_FILTER_OFF | GPIO_PUSHPULL | GPIO_PULLUP)
#define GPIO_LED_D11 \
(GPIO_PORT3 | GPIO_PIN3 | GPIO_VALUE_ONE | GPIO_OUTPUT | \
GPIO_MODE_DIGITAL | GPIO_FILTER_OFF | GPIO_PUSHPULL | GPIO_PULLUP)
#define GPIO_LED_D12 \
(GPIO_PORT3 | GPIO_PIN14 | GPIO_VALUE_ONE | GPIO_OUTPUT | \
GPIO_MODE_DIGITAL | GPIO_FILTER_OFF | GPIO_PUSHPULL | GPIO_PULLUP)
/* Button definitions *******************************************************/
/* The LPCXpresso has four switches:
*
* SW2 ISP2 P0.6
* SW3 ISP1 P0.5
* SW4 ISP0 P0.4
* SW5 User Button P1.1
*
* In all cased, the signal is low when the button is pressed.
*
* SW2, SW3, SW4 can be used to force the LPC546xx in to ISP boot modes.
* After boot these buttons could be used as user buttons. However, they are
* not available when the on-board SRDRAM is used because P0.4, P0.5, and
* P0.6 are also used as EMC_D2, EMC_D3, and EMC_D4, respectively.
*
* So SW5 is really the only button that that is generally available for
* software usage. When pressed, it will be sensed low.
*
* P1.1 is a Type D pin.
*/
#define GPIO_BUTTON_USER \
(GPIO_PORT1 | GPIO_PIN1 | GPIO_INTBOTH | GPIO_MODE_DIGITAL | GPIO_FILTER_ON)
/* LCD/TSC definitions ******************************************************/
/* The backlight is controlled by P3.31 and is intended to connect via PWM
* to control the brightness level. For simplicity here, it configured as a
* simple GPIO output.
*
* The output goes to the enable (EN) pin of a AP5724 step-up DC/DC
* converter designed to drive white LEDs with a constant current. A high
* input at EN turns the converter on, and a low input turns it off.
*/
#define GPIO_LCD_BL \
(GPIO_PORT3 | GPIO_PIN31 | GPIO_VALUE_ZERO | GPIO_OUTPUT | \
GPIO_MODE_DIGITAL | GPIO_FILTER_OFF | GPIO_PUSHPULL | GPIO_PULLUP)
/* The integrated touchscreen uses one GPIO out and one GPIO interrupting
* GPIO input:
*
* P2.27 CT_RSTn Active low
* P4.0 INTR On falling edge, I belieive
*
* The FT4x06's WAKE-UP interrupt pin is not brought out.
*/
#define GPIO_FT5X06_CTRSTN \
(GPIO_PORT2 | GPIO_PIN27 | GPIO_VALUE_ZERO | GPIO_OUTPUT | \
GPIO_MODE_DIGITAL | GPIO_FILTER_OFF | GPIO_PUSHPULL | GPIO_PULLUP)
#define GPIO_FT5X06_INTR \
(GPIO_PORT4 | GPIO_PIN20 | GPIO_INTFE | GPIO_MODE_DIGITAL | GPIO_FILTER_OFF)
/* I2C addresses (7-bit): */
#define CODEC_I2C_ADDRESS 0x1a
#define ACCEL_I2C_ADDRESS 0x1d
#define FT5X06_I2C_ADDRESS 0x38
/****************************************************************************
* Public Types
****************************************************************************/
/****************************************************************************
* Public Data
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Public Functions Definitions
****************************************************************************/
/****************************************************************************
* Name: lpc54_bringup
*
* Description:
* Perform architecture-specific initialization
*
* CONFIG_BOARD_LATE_INITIALIZE=y :
* Called from board_late_initialize().
*
* CONFIG_BOARD_LATE_INITIALIZE=n && CONFIG_BOARDCTL=y :
* Called from the NSH library
*
****************************************************************************/
int lpc54_bringup(void);
/****************************************************************************
* Name: lpc54_sdram_initialize
*
* Description:
* Initialize external SDRAM
*
****************************************************************************/
#ifdef CONFIG_LPC54_EMC
void lpc54_sdram_initialize(void);
#endif
/****************************************************************************
* Name: lpc54_lcd_initialize
*
* Description:
* Initialize the LCD. Setup backlight (initially off)
*
****************************************************************************/
void lpc54_lcd_initialize(void);
/****************************************************************************
* Name: lpc54_i2ctool
*
* Description:
* Register I2C drivers for the I2C tool.
*
****************************************************************************/
#ifdef HAVE_I2CTOOL
void lpc54_i2ctool(void);
#endif
/****************************************************************************
* Name: lpc54_ft5x06_register
*
* Description:
* Register the FT5x06 touch panel driver
*
****************************************************************************/
#ifdef HAVE_FT5x06
int lpc54_ft5x06_register(void);
#endif
/****************************************************************************
* Name: lpc54_i2c_handle
*
* Description:
* Create (or reuse) an I2C handle
*
****************************************************************************/
#if defined(HAVE_I2CTOOL) || defined(HAVE_FT5x06)
struct i2c_master_s *lpc54_i2c_handle(int bus, int ndx);
#endif
/****************************************************************************
* Name: lpc54_i2c_free
*
* Description:
* Free an I2C handle created by lpc54_i2c_handle
*
****************************************************************************/
#if defined(HAVE_I2CTOOL) || defined(HAVE_FT5x06)
void lpc54_i2c_free(int ndx);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_ARM_LPC54XX_LPCXPRESSO_LPC54628_SRC_LPCXPRESSO_LPC54628_H */
Reference in New Issue View Git Blame Copy Permalink